Home

Datasheet

1. ee
2. offset 01 00 OK n p shaft faktor 3 000 OK Effective Circumference 3000 OK Vehicle Registration No NOIL 00000 OK Vehicle Registration Date 2013 06 01 OK Registering Member State PL OK Speed Authorised km h 90 End Click value to edit Set Product Code fig 3 tachograph data read Editing data Click the editable value to open edit box OK UTC 2010 03 24 08 14 offset 01 00 OK shaft faktor gt DK OK Effective Circumference 5580 Buttons gt Revert to original value Cancel edit OK Confirm edit The value will be validated and the data will be prepared to write operation If the value is incorrect the message will appear Please correct data Writing data The ProgS software allows writing only to Tachograph Simulator DTCOSIM The DTCOSIM must be connected using USB KSIM infertace with DTC cable Cables between USB KSIM and tachographs tachograph simulator can be changed without unplugging USB KSIM from computer Click Write DTCOSIM to write data to DTCOSIM If the modified only box is checked only modified data will be saved to DTCOSIM otherwise all data will be sent and saved into DTCOSIMM Clicking the Add data to write button will open additional data list to write fig 4 This list is used to add values that are supported by the tachograph simulator but was not read from the attached device For example if data co
3. service manual for instructions For DTCO and 2400 tachograph the Product Code can be set using Set Product Code button After clicking the Set Product Code button the configuration window will appear The configuration window will initially setup Product Code with data read from attached device The configuration will be made in 1 or 2 steps depending on the tachopgraph configuration For with CANTCO1 repetition rate parameter equal to 0 there will be only one step configuration as the 10 th digit of Product Code will be permanently set to 1 Further instructions will be displayed in configuration windows Setting Product Code STEP 1 Second digit after dot determine CAN interface type If this digit is 0 the CAN interface is disabled Try with digits 2 or 3 and choose the right one by watching the speedometer If the speedometer is working properly the digit is correct and should not be changed in next steps 1324 0 0000000100 Write DTCOSIM TEZ AAA A MA k n E a DTCOSIM Programmer ProgS Te Setting Product Code STEP 2 The 10 th digit after dot determines period of speed information transmission through CAN bus 2 10 ms period F 20 ms period 1 4 5 5 ms period Additionally 4 or 5 will set HAYD repetition period to 100 ms 1324 020000000 01 Write DTCOSIM HC A A A ce r r r A en
4. 78129 Device Type Interface USB KSIM Stoneridge 400 Siemens DU 1324 set below are examples for each DTCOSIM Programmer ProgS v1 05 XX modified only Write DTCOSIM Reading Data AO AA AN O Manufacture date Odometer km K const VIN UTC oip shaft faktor Add data to write fig 2 2400 tachograph data read DTCOSIM Programmer Progs USB Device gt Device Mo 1305078129 Device Type Interface USB KSIM Product Code WIN Reading Data Manufacture date Time Offset UTC Odometer km Effective Circumference K const o p shatt faktor Add data to write fig 3 1324 tachograph data read 2011 07 13 108064 6 9000 WMAH05 77 3M35000X 2013 05 29 08 14 offset 01 00 3 000 Click value to edit Set Product Code DTCOSIM Programmer ProgS v1 05 XX modified only Write DTCOSIM 1324 020000000500 WMAHO57773M35000X 2011 07 13 01 00 2013 05 29 08 15 08 108064 6 3000 9000 3 000 Click value to edit az DTCOSIM Programmer Prog5 USB Device DTCOSIM Programmer Device No 1305078129 Device Type Interface USB KSIM Progs v1 05 XX Eee modified only Siemens VD 1324 Head ll Write DT COSIM Reading Data MANTAN OK ECU Hardware No 1381 OK Manufacture date 2011 07 13 OK K const 9000 OK Odometer km 108064 6 OK VIN WMAH057773M35000X OK Tyre Size 295 95R22 5 OK Next Calibration 2013 01 01 OK UTC 2013 05 29 08 15
5. ProgS 1 05 tachograph simulator programming tool USER MANUAL Ver 1 0 06 2013 KT ProgS software ProgS is a software tool to read data from tachograph and program DTCOSIM tachograph simulator The software communicates with the tachograph simulator or tachograph using USB KSIM interface The ProgS software works on Windows XP and Windows 7 Main program window ag DTCOSIM Programmer ProgS USB Device DTCOSIM Programmer Device No 1305078129 Ms ProgS v1 04 XX Device Type Interface USB KSIM modified only Read Please select the type of tachograph and click Head fig 1 main program window Reading data The ProgS can read from tachograph or tachograph simulator The tachograph tachograph simulator should be connected to computer using USB KSIM interface Select the type of tachograph device that will be read and press Read The ProgS software can read data from tachograph or tachograph simulator In case of reading from tachograph simulator the device type should be set to the device that is simulated by DTCOSIM The USB KSIM should be connected to the target device using appropriate connector kit DTC to connect to digital or tachograph simulator STN to connect to Stoneridge 2400 tachograph 1324 to connect to 1324 tachograph Each tachograph type contains different data type of tachograph lag DTCOSIM Programmer ProgS USB Device gt Device No 13050
6. me from 1324 tachograph the add data to write list will have 2400 and DTCO tachograph specific parameters These additional data can be edited and wrote to the device together with all other parameters The additional data are written if it is not empty This means that if you don t want to write it it should be left blank delete the parameters value ag DTCOSIM Programmer Prog5 E USB Device Device Mo 1305078129 Device Type Interface USB KSIM DTCOSIM Programmer ProgS v1 05 x Stonendge 2400 Modified only Siemens VDO 1324 Read STOP Write DTCOSIM DTCO Reading Data MENE OK Manufacture date OK Odometer km K const VIN UTC oip shaft faktor 2011 07 13 108064 6 9000 WMAH057 773M35000X 2013 05 29 08 24 offset 01 00 3 000 Click value to edit Additional data to Write always written if nat empty Set Product Code Code Effective Circumference Tyre Size Next Calibration Vehicle Registration No Vehicle Registration Date Registering Member State Speed Authorised km h fig 4 additional data list Setting Product Code 3000 295 95R22 5 2013 01 01 NOL00000 2013 01 01 PL 90 Click value to edit parameter The Product code must be set for the tachograph simulator to work properly This parameter consist of 16 digits with dot after 4 th digit example 1324 620000000400 For the 1324 type tachograph the Product Code is set manually Refer to DTCOSIM

Datasheet

Contents

Download Pdf Manuals

Related Search

Related Contents