Feeding Frenzy System Operator Manual
Contents
1. Feeding Frenzy System Documentation 040 FF OPER UCT Rev B gt Read this manual before use Keep this manual with the machine at all times www globalw com http service globalvr com techsupport globalw com Phone 408 597 3435 Fax 408 597 3437 2006 Global VR Inc All Rights Reserved Feeding Frenzy is a Trademark of Sprout Games LLC Used under License GLOBAL VR and the GLOBAL VH logo are registered trademarks of Global VR Inc All other trademarks are the properties of their respective owners Table of Contents Chapter 1 INTRODUCTION 1 1 Safety 3 1 2 Warnings 3 1 3 Environment Conditions 4 1 4 FCC Regulatory Notices 4 1 5 Feeding Frenzy Game Features 5 1 6 Cabinet Models and Features 6 Chapter 2 GAME SETUP 2 1 Pre Game Installation 7 2 2 Fish Panel Installation 8 2 3 Playing a Feeding Frenzy Game 10 Chapter 3 OPERATOR MENUS 3 1 How to Use the Operator Menus 11 3 2 Operator Menu 12 did Settings Menu 13 3 4 Statistics Menu 16 3 0 Diagnostics 16 3 5 1 Video Test 17 Chapter 4 SERVICE 4 1 system Restore CD 18 4 2 Troubleshooting 19 4 3 Cabinet Specifications 24 4 4 Jamma Harness Wire Diagram 25 4 5 Computer Diagram 26 4 6 Technical Support Contact Info 27 4 7 Feeding Frenzy Warranty Info 28 2 Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 Chapter 1 INTRODUCTION 1 1 SAFETY NOTICES The following safety instructions apply to all game operators and service pe2. Location The Settings menu has seven sub menus that are used to setup the cabinet location information the amount of coins that are needed to start a game sound levels redemption play and tournament settings Below is a detailed description of each menu found under the Settings menu 3 3 1 Game Settings The Game Settings will adjust the playing functions and software settings of the game Trackball Sensitivity This will adjust how fast or slow trackball responds to the player This will also affect how much the DASH button works Starting and Continue Lives This will adjust how many lives a player gets when they start or continue a game Difficulty This will adjust the speed of the enemy fish and the amount of time give to clear a level First Free Life amp Additional Lives This will set the amount of points needed to earn an extra life within the game Intelli Tune This is an automatic game difficulty adjusting tool that helps optimize the earnings of the cabinet Intelli Tune will measure the players performance in the game and adjust the game difficulty to achieve the desired game length This helps beginners learn the game and helps to limit experts to a set amount of playing time Adjust the desired game length min and max time limits as needed Game Settings Min Trackball Sensitivity Starting Lives Mi OUT Lives Regel Score on Continue Difficulty First Free Life ai Nddilional Livea avery n 10000 g
3. While this computer system has been designed and determined to be compliant with regulatory agency limits for EMI there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference with radio communications services which can be determined by turning the equipment off and on you are encouraged to try to correct the interference by one or more of the following measures e Reorient the receiving antenna e Relocate the computer with respect to the receiver e Move the Feeding Frenzy away from the receiver e Plug the Feeding Frenzy into a different outlet so that the computer and the receiver are on different branch circuits If necessary consult a Regulatory EMC representative of Feeding Frenzy Technologies or an experienced radio television technician for additional suggestions You may find the FCC Interference Handbook 1986 to be helpful It is available from the U S Government Print Office Washington DC 20402 Stock No 004 000 00450 7 or on the word wide web at http www fcc gov bureaus compliance www tvibookt html This device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and and if not
4. Dash Not Used GRY WH 24 WH RED P1B3 Out of Tickets Not Used GRN YL 2d 5 GRN RD Not Used Not Used OR BLK EN 26 OR RD Not Used Ground BLK 27 BLK Ground Ground BLK 28 BLK Ground 2006 GLOBAL VR All Rights Reserved ES Ss Note Wire colors may vary due t o harness revisions 25 26 uim Suppl ia TES Ihre AC Power Power AC Power input must use a EC 14 power cord connector Power AC Power input must use a EC 14 power cord connector must use a IEC 14 power cord connector one of the power connectors from the power supply to DC Power the UGCI P to provide 12vdc and 5vdc power in the JAMMA harness 3 JAMMA Connect the JAMMA harness to the UGCI P board The trackball will connect directly to the PS 2 port on PS 2 the computer The Printer Port on the computer connects to the printer port EN Printer Port on the UGCI P Connect the USB HASP Security Dongle to the USB ports on Em eran the motherboard 7 Audio Out The Green Audio Out Port on the computer connect to the Audio In port on the UGCI P Video Out Connect the Video cable from the monitor to the 15 Pin Video Port on the computer Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 4 6 TECHNICAL SUPPORT CONTACT INFO Service amp Parts Hours 7 00AM 5 00PM Pacific Time Monday Friday Phone 408 597 3435 Fax 408 597 3437 E mail techsupport globalvr com Website hitp service globalvr com Free
5. 20000 amp K amp A ITE Desired Game Length os Cycles 1435 GE Min O00 amp Max oEcE ECEOE E Dolo 2006 GLOBAL VR All Rights Reserved 1 3 3 3 2 Credits Settings The credits menu will set how many credits each coin drop is worth and how many credits it takes to play a game You can also set the game to freeplay from this menu 3 3 3 Sound Settings The sound menu will adjust the sound levels for both the music and game play sound You can turn the attract mode sound on or off The global sound will control the over all sound levels of the cabinet instead of having to adjust the music and sound levels individually Sound Settings Credit Settings Each Coin 9 01 Credit s Music ome E Min Max P HU ME AE UE Each Play cNEI g Credit s Sound X Attract Sound A Freeplay E Master Volume 3 3 4 Timers The input timeout will adjust how long a game will stay in play without any input from the trackball or buttons from a player The intro and wrap up timeouts will adjust how long the game will display the game info screens when a game level is started intro and when the game level has ended wrap up T Timer 5 Input Timeout 0 30 G Seconds Intro Timeout 010 amp Seconds Wrapup Timeout 010 f Seconds 1 4 Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 3 3 5 Redemption The redemption menu is used to modify the redemption settings for the game Redemp
6. port on the monitor Check the video cable and make sure it is not pinched or frayed If you are getting no audio and no video and the computer is powered on you might have a faulty hard drive or corrupted software on the hard drive Reload the software from the System Restore CD to see if this solves the problem If you continue to have hard drive problems after you reload the software you may have a faulty hard drive Verify the line voltage is set to the correct voltage for your area 115V or 230V Unplug the AC power cord from the computer and re plug it back in to power on the computer If the UGCI P card is bad all buttons and controls on the cabinet will not work Make sure that the UGCI P card has power plugged into it from the computer power supply Verify that the DB 25 cable is firmly connected to the UGCI P card Verify that no wires are frayed or improperly shorting to ground in the wire harness Verify that the external PC power supply is working This provides 12 volt and 5 volt DC power to the hardware connected to the wiring harness 21 4 2 4 Control Troubleshooting Problem Cause Possible Solution Buttons do not work Bad micro switch Replace the micro switch on the button and re test Verify that the wires are connected to the correct spades on the micro switch Bad wiring Turn off the cabinet Verify that all the wires are firmly connected to each button Verify that no wires are frayed or improper
7. telephone e mail and online support are provided for systems during the warranty period GLOBAL VR Technical Support can help you troubleshoot problems and diagnose defective parts We can also answer questions about the operation of your game When you contact Technical Support please provide the information listed below as applicable to assist the Technical Support representative in solving your problem quickly For your convenience space is provided to write important numbers e Cabinet Serial Number e Operating System Version and Games Installed e Proof of Purchase information e Your mailing address and telephone number e Asummary of the question or a detailed description of the problem e Specific error message e Date of latest install or upgrade e Any changes made to the system e For game play issues the game and number of players e To comment on this document please e mail techpubs globalvr com Warranty Service If at some point you require warranty service contact your distributor If technical support staff determines that parts on your Feeding Frenzy cabinet are defective a Return Merchandize Authorization RMA number will be issued 2006 GLOBAL VR All Rights Reserved 2f 4 7 FEEDING FRENZY WARRANTY INFO 28 LIMITED WARRANTY GLOBAL VR warrants that its computer circuit boards hard drives power supplies monitors displays controls sensors and mechanical structures are free from defects
8. 00 M X Computer Hard Drive 3 5 Inch ATA66 40GB Computer CD ROM Drive 5 25 ATA 24x Computer CPU Intel 2 0Ghz Celeron 478 HS Computer M emory PC2100 256M B DDR266 Computer Chassis T4 Base Only Graphics Feeding Frenzy 27 Control Panel Graphics Feeding Frenzy 27M arquee Graphics Feeding Frenzy 27 Left Graphics Feeding Frenzy 27 Right Computer UGCI P JAMMA O Card Software Feeding Frenzy 27 VGA Flat Monitor 27 VGA Flat Monitor Chassis PCB Monitor Bezel Monitor Glass Speakers Entropy Ticket Dispenser Feeding Frenzy JAM MA Harness Leg Levelers Cabinet Wheels Trackball 3 inch White Power Plate with Fuse and Connectors Coin Door Assembly M eter Service Switch Cabinet Fans Power Strip 6 Outlets Button Green Button Red Button Player 1 Button Player 2 Keys Rear Door Keys Fish Panels Keys Coin Door Keys Coin Vault RS IR3 RS eo n e oa ees ica sca es ees e em Hi ca ien een res pe s e pesa nsa n ise e a es s e o ps ende ed ied Lied 2 lt Part Number 040 FF OPER UCT 115 ACPOW ER CBL 115 AUD MIN CBL 115 CAT5E7B CBL 115 CDIDE40 CBL 115 PRINTER CBL 115 USB6A A COM 136 FF27002 LAI 138 FUNNEL FAR 285 ATX250W SPA 290 P4800M X ASU 300 40GB3 5 ATA 305 24X52 5 SAM 310 C2 0GHZ INT 315 256 266 DDR 850 T4 BASE MET 890 FF27CON ART 890 FF27M RQ ART 890 FF27LS ART 890 FF27RS ART 990 UGCI P UCT 997 FF GAM E UCT 115 FFJAMMA CBL Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7
9. 5 2006 4 4 JAMMA HARNESS WIRE DIAGRAM tBundie l 5 Control Parsi id m 5m END rs c5 se gy c1 18 a JAMMA go Se 5 Psr ag i woe Connector x ge PT Butten 1 L ai 18 i ie ui JB 415 418 eee mo B 9 Tw IL es Bits 1 03 8 g 57 g PZ Sioi L Bundie 29 lt Redenp tlg Ca 96 cui 1H ce Ba L E a l1 sx dist LH cm om 1 Ma i et ce P1 B3 Qui of Ticwets 18 oa 17 Cli T w amp Loop mq B Guo B DNI amp Loop Coin in 1 vi IB zi B ee he xi 1B ud JB 6 Loop c B ge SP 4 f 3 a a B D RM B d Bundle 3469 Bp cu IB mo 108 Lae l 108 is zi JAMMA PIN OUT COMPONENT Ground EN i BLK Ground Ground EM BLK Ground 45V RD o RD 5V 5V RD EM 4 RD 5V 5V BL EM 5 BL 5V 12V OR EDEN s OR 12V KEY E l7 KEY Not Used WH RD 8 WHBLK Meter 4 Not Used BLK GRN 9 GRY Ticket Dispenser Left Speaker BL RD E BE 10 RD YL Left Speaker Right Speaker BL GR 11 RD BLK Right Speaker Not Used GRN 2 RD Not Used Not Used WH eee 33 BL Not Used Not Used WH OR ae 14 BLK Not Used Not Used BLK WH LEM 15 wHBRN Test Switch Coin 2 BRN BLK 16 YUBLK Coint P2 Start RD WH mee 17 RD P1 Start Not Used BL WH ae is BL Not Used Not Used GRN WH T 19 GRN Not Used Not Used OR WH ae 20 OR Not Used Not Used YL WH BEEN gt YL Not Used Not Used BRN WH EM 22 BRN P1B1 Inhale Not Used PR WH ENS 23 PR P1B2
10. IL d q E tti ng S Music AE AE MU Setti ngs Game p Sound AS a UE Statistics Diagnostics Attract Sound f Language English Use the trackball to move the selection arrow through the operator menu Press the DASH button to select a menu or to change a game setting 2006 GLOBAL VR All Rights Reserved 1 1 Operator Menu Settings Slalistics Diagnoslics Reset Defaults Reset High Scores VERSION RC1 115 1028 160000 SERIAL CAD23092743 The operator menu is the default screen displayed when you press the test switch Use the BACK option to return to the previous menu screen throughout the different menus This menu holds the game sound credit and redemption settings This menu shows the accounting data for the game The amount of credits earned games played and last time the statistics data was reset Use this menu to test and validate that the hardware on the Diagnostics cabinet is working correctly L Use this setting to adjust the default Language used in the anguage game and operator menu Reset Defaults Use this setting to reset the operator menu settings to the default factory settings the cabinet shipped with Use this setting to reset the high score table displayed in the Reset High Score attract mode 1 2 Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 3 3 SETTINGS MENU Setti ngs Gema pu Credit Salop Sound Salop Timor amp elup Redempbon Toaormgnmont
11. LITY PERFORM ANCE OR SAFETY OF ANY NON GLOBAL VR PART OR ANY M ODIFICATION PERFORM ED BY ANY PRODUCT DISTRIBUTOR UNLESS SUCH WORK IS EXPRESSLY AUTHORIZED IN ADVANCE BY GLOBAL VR THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESSED OR IM PLIED WARRANTIES INCLUDING THE IM PLIED WARRANTIES OF M ERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND ALL OTHER OBLIGATIONS OR LIABILITIES ON GLOBAL VR S PART EXCEPT FOR ANY EXPRESS WARRANTY SET FORTH IN A WRITTEN CONTRACT BETWEEN GLOBAL VR AND PURCHASER CONTAINING SPECIFIC TERM S WHICH SUPERSEDE THE TERM S HEREIN THIS WARRANTY DOES NOT AUTHORIZE ANY OTHER PERSON TO ASSUME OTHER LIABILITIES IF ANY CONNECTED WITH THE SALE OF PRODUCTS BY GLOBAL VR Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006
12. This shows the total amount of credits inserted for the game F This shows the total amount of time left to eat fish and complete the growth bar to move onto the next level Trackball This is used to move Andy the fish across the screen Andy will move in the direction the trackball is rolled Dash Button This button is used to quickly move Andy across the screen Be careful you don t swim right into the mouth of another fish Inhale Button This button is used to vacuum up fish you can eat in a small area in front of you his button is only used with certain fish like the Lion fish shown above 1 0 Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 Chapter 3 OPERATOR MENU 3 1 HOW TO USE THE OPERATOR MENU This chapter describes how to use the operator menu to setup and adjust the settings on your Feeding Frenzy cabinet All game settings such as Language Cabinet Setup Game Configuration Accounting and Diagnostics are options of the Operator Menu Press the test switch behind the coin mech door as shown in the figure below to display the operator menu Operator Menu Sellings Slahglica Diagnostica Minuet Delmia Rigol High Scorag CoinzDoord Once in the operator menu you will use the trackball to highlight menu options and the DASH button will be used to select the menu items You can use the test switch at any time to exit the operator menu and return to the game Operator Menu c OUT
13. abinet so that at least one Fish Panel can easily be seen by customers as they walk through your arcade location The Fish Panels draw attention to this unique cabinet and help drive up earnings 2006 GLOBAL VR All Rights Reserved 9 n a P is o EVE The outer edge of the screen is filled with information bars that help explain the size of the fish and what fish you can eat in the game Each information bar is described below The goal of the game is to eat as many fish as you can without being eaten yourself and to complete the growth bar before the clock runs out to move onto the next level A The Menu bar tells you what fish you can eat for that level As you eat fish you grow in size when you grow in size another fish becomes available to eat off the screen B This shows your total score for the game The more fish you eat the more points you earn C The Growth Bar shows how many fish you have to eat for this level Eating more fish will add to the bar When you reach the red triangles in the Growth bar you grow to the next size fish and you can now eat the next available fish shown in the Menu bar A D The Ability bar is only used after stage eight when you are a Lion Fish or better When the Ability bar is charged you can use the INHALE button to suck fish into your mouth As you use the INHALE button the energy from the ability bar is used The Ability bar when empty will slowly recharge as you play the game E
14. anel with water Now unlock the Fish Panel doors and pull them open from the top and remove them from the cabinet tz Back side of Fish Panels 2 Take the Fish Panel doors over to your sink where you will fill the Fish Panel with water On the back side of the Fish Panel door is a water fill hole as shown in the picture below Do not fill the Fish Panel completely full of water as it will spill over the top edge when powered on instead leave a 1 inch gap of air at the top as shown in the picture below foul Back side of Fish Panel 8 Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 3 Insert the Fish Panel door back into the cabinet Make sure the air hose coming out of the bottom of the Fish Panel door goes into the slot on the bottom edge of the Fish Panel cutout on the cabinet as shown in the picture below If the air hose is not installed correctly the Fish Panel door will pinch the air hose when closed and you will get very little air flow to bubble the fish inside the Fish Panel 4 Close and lock the Fish Panel doors Next from the back of the cabinet plug the air hose from the air pump into the one way valve from the Fish Panel and you are finished When the cabinet is powered on the fish inside the Fish Panel will begin to swim around from 4 or 5 streams of bubbles creating a very unique cabinet Arrow shows direction of air flow GLOBAL VR recommends displaying the Feeding Frenzy c
15. aser with a substitute unit or on site service during the warranty period or at any time If after investigation GLOBAL VR determines that the reported problem was not covered by the warranty Purchaser shall pay GLOBAL VR for the cost of investigating the problem at its then prevailing per incident billing rate No repair or replacement of any Product or part therein shall extend the warranty period as to the entire Product The warranty on the repaired part only shall be in effect for a period of ninety 90 days following the repair or replacement of that part or the remaining period of the Product parts warranty whichever is greater Purchaser s exclusive remedy and GLOBAL VR s sole obligation is to supply or pay for all labor necessary to repair any Product found to be defective within the warranty period and to supply at no extra charge new or rebuilt replacements for defective parts If repair or replacement fails to remedy the defect then and only in such event shall GLOBAL VR refund to Purchaser the purchase price for said Product Purchaser s failure to make a claim as provided above or continued use of the Product shall constitute an unqualified acceptance of said Product and a waiver by Purchaser of all claims thereto IN NO EVENT SHALL GLOBAL VR BE LIABLE FOR LOSS OF PROFITS LOSS OF USE INCIDENTAL OR CONSEQUENTIAL DAM AGES RESULTING FROM OPERATION OF THE GAME IN ANY CONDITION GLOBAL VR SHALL NOT BE RESPONSIBLE FOR THE SUITABI
16. cabinet at your location ls 3 4 Carefully remove the cabinet from the shipping container Give yourself plenty of space around the cabinet as you remove it from the shipping container Inspect the exterior of the cabinet for any damage Move the Feeding Frenzy cabinet to the location were it will be operated Avoid installing the game where it is damp and dusty or where the cabinet will receive excessive sunlight or heat to protect the game from rising internal temperatures Hemove the keys from the coin return slot Open the coin door to locate the second set of keys as shown in the picture below E 1 Cash Box E lr y Zak Cabinet Keys Coin Door Mi Coin Door n asiiBox Open the cash box door and remove the loose parts inside the cash box You will find the following items may vary with cabinet style Feeding Frenzy Operator Manual this document Feeding Frenzy System OS CD AC power cord Monitor Service Manual Hemove the back door from the cabinet and inspect the computer system Verify that all cables and wires are securely connected to the computer See page 25 for a guide to the cable connections Verify all major assemblies are securely mounted and that there are no loose objects inside the cabinet that could cause any damage Install the Fish Panels and fill up with water See section 2 2 on page 8 for instructions Connect the wall cord to a grounded 3 terminal AC wall outlet Powe
17. he speaker s grill covers and visually inspect each speaker is in working order Run the Sound Test from the Operator M enu to verify each speaker is working Faulty wiring A weak or low muffled sound is a sign of reversed speaker wires Check for reversed wires on each speaker Bad Power Supply A constant low hum in the speakers can be a faulty or bad power supply Bad UGCI P You can verify the UGCI P is working by installing it into another working cabinet If that is unavailable to you plug a simple computer speaker into the audio ports on the computer and verify that sound is working from the computer Blown Speakers Remove the speaker grill covers and visually inspect each speaker is in working order Run the Sound Test from the Operator M enu to verify each speaker is working Bad Wiring Turn off the cabinet Verify that all the wires are firmly connected to each speaker Verify that no wires are frayed or improperly shorting to ground Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 4 2 3 Computer Troubleshooting Problem No Video No video no audio No control panel or button functions Cause Loose or bad video cable Faulty hard drive No power to computer No power to the UGCI P card Bad wiring Bad power supply 2006 GLOBAL VR All Rights Reserved Possible Solution Verify that the video cable is firmly connected to the computer 15 pin video port and the 15 pin video
18. ime 3 5 DIAGNOSTICS Diagnostics Move the Trackball in any direction Press any botton When done Test Sound Left Right Test Trackball Start Tegt Video Start Ticket Dispenser Dispense Tic Ket Test Inr T i m m d I S eg npu m 24 ia Al w a Tournament Server EX Test Test Trackball Screen Use the diagnostics menu to test the cabinet hardware If you press a button on the control panel it will show what button was pressed in the test input screen above You can test the left and right speakers to verify each speaker is working correctly The test trackball screen will verify the trackball is working correctly The dispense ticket button will dispense one ticket when pressed to test the ticket dispenser The tournament server test is reserved for future use 1 6 Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 3 5 1 VIDEO TEST When you begin the video test to calibrate the monitor use the DASH button to start the test and the DASH button to scroll through the screens When you have scrolled through all the test patterns you will return to the CAGNO LES menu nu HEHHIHIEIE BBH EREE HEU tH Use the video test screens to evaluate the monitor s calibration and color Each screen is designed to help you align the horizontal and vertical sync or adjust the white balance and color hues Use the monitor control panel buttons to adjust the monitor The monitor c
19. in materials and workmanship under normal use and service for a period of ninety 90 days from the date of shipment All software and accompanying documentation furnished with or as part of the Product is supplied AS IS with no warranty of any kind except where expressly provided otherwise in any documentation or license agreement furnished with the Product During the warranty period GLOBAL VR will at no charge repair the Product provided Purchaser believes that the Product is defective in material or workmanship and promptly notifies GLOBAL VR in writing with an explanation of the claim All claims for warranty service are made within the warranty period Products are returned adequately packed and freight prepaid to GLOBAL VR s designated service center GLOBAL VR s inspection or test of the Product verifies to GLOBAL VR s satisfaction that the alleged defect s existed and were not caused by accident misuse neglect unauthorized or attempted repair or testing unauthorized modification incorrect installation vandalism failure to follow the maintenance schedule or procedures or operation in out of specification environmental conditions GLOBAL VR will return the repaired Product freight prepaid to the Purchaser All freight costs associated with replacement of warranty parts after expiration of the original warranty period are the responsibility of the Purchaser GLOBAL VR is not obligated to provide the Purch
20. installed and used in accordance with the instruction manual may cause harmful interference with radio communications Operation of this equipment in an residential area is likely to cause harmful interference in which case you will be required to correct the interference at your own expense Operation is subject to the following conditions e This device may not cause harmful interference e This device must accept any interference received including interference that may Cause undesired operation Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 1 5 FEEDING FRENZY GAME FEATURES Congratulations on choosing Feeding Frenzy Feeding Frenzy is available in a 27 VGA custom cabinet and a 3 4 height 19 VGA cabinet designed for ten year old children Feeding Frenzy is designed to work as a standard Coin OP cabinet where the player competes against the game through forty different game levels or as a redemption game with the ability to dispense tickets as the player earns points in the game In either mode Feeding Frenzy offers a unique fun game for men women and children Feeding Frenzy provides the following benefits to operators A unique game targeting all ages including women and children Easy to use operator menu interface Fish Bubblers built into the sides of the cabinet help attract players The Feeding Frenzy cabinet can be run as a story mode Coin Op or offer full Redemption Mode play to players Opera
21. ly shorting to ground Bad UGCI P Card If the UGCI P card is bad all buttons and controls on the cabinet will not work M ake sure that the UGCI P card has power plugged into it from inside the computer Trackball does not Bad wiring Verify that no wires are frayed or are improperly shorting work to ground Verify the trackball cable is plugged into the PS 2 port on the computer Sloppy or bad Bad TTL sensors Go into the Operator Menu and run Test Trackball Spin trackball response the trackball in all directions and verify that you are getting a good response If you feel the trackball is not responding correctly the sensors on the trackball may need to be cleaned or replaced or the bearings on the trackball are wearing out and need to be replaced 22 Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 4 2 5 Miscellaneous Troubleshooting Problem Cause Possible Solution Cabinet gets very Faulty ventilation fan Verify that the exhaust fan is working It is located near warm the vents at the top of the cabinet Replace the fan if worn or spinning slow Ventilation holes on Make sure you have proper clearance between the cabinet cabinet are blocked rear and the wall Make sure the vent s holes are clear of dust and that air can flow freely M arquee lamp is bad Faulty fluorescent Check the fluorescent tube for darkened or cracked end or Intermittent tube Replace the fluorescent tube if it looks worn Faul
22. onents e Keep your computer far away from radiator and heat sources e Do not block cooling vents 1 2 WARNINGS N To avoid electrical shock unplug the cabinet before performing the installation procedures CAUTION GLOBAL VR assumes no liability for any damages or injuries incurred while setting up the cabinet Only qualified service personnel should perform this installation 2006 GLOBAL VR All Rights Reserved 3 1 3 ENVIRONMENTAL CONDITIONS Feeding Frenzy is intended for indoor use only Be sure to keep the cabinet dry and maintain an operating temperatures of 10 40 Celsius or 50 105 Fahrenheit 1 4 FCC NOTICES UNITED STATES Electromagnetic Interference EMI is any signal or emission radiated in free Space or conducted along power or signal leads that endangers the functioning of a radio navigation or other safety service or seriously degrades obstructs or repeatedly interrupts a licensed radio communications service Radio communications services include but are not limited to AM FM commercial broadcast television cellular services radar air traffic control pager and Personal Communication Services PCS These licensed services along with unintentional radiators such as digital devices include computer systems contribute to the electromagnetic environment Electromagnetic Compatibility EMC is the ability of items of electronic equipment to function properly together in the electronic environment
23. ontrol panel is located underneath the front control panel Use the buttons on the monitor control panel to bring up the O S D or On Screen Display to select adjust and set the available monitor calibration options 2006 GLOBAL VR All Rights Reserved 1 T Chapter 4 SERVICE 4 1 SYSTEM RESTORE CD USB HASP w Security Dongle Activated TEF ade Sinstaliation USK E Vor B iii vien se uw ze USB HASP Security Dongle NOT Activated a In the event the software on the computer becomes corrupt or you run into software problems you can restore the software on your Feeding Frenzy computer The System Restore CD will load the operating system and game software from CD Please be aware when you use the System Restore CD you will erase all history for the coin and game statistics held in the game System and Game Restore CD Power on the cabinet and open the computer CD ROM drive Insert the CD labeled Feeding Frenzy Disc 1 Next power the cabinet off wait 5 seconds then power the cabinet back on The CD should automatically start up wait about 60 seconds and on screen you should see the hard drive image process starting 2 When the hard drive image process has finished open the CD ROM drive and remove the CD Power the cabinet off wait 5 seconds then power the cabinet back on 3 When the game has started the attract mode will begin Press the test switch behind the coin door to enter the ope
24. r ON the cabinet using the On Off switch located on the lower rear of the cabinet to verify proper operation After you power the cabinet on the picture on the monitor may be temporarily distorted this is caused by the change in the Earth s magnetic field as you move the cabinet from one location to another You can fix this problem by using the degaussing feature built into the monitor If you monitor does not have a degaussing feature you can use a degaussing coil to restore the color variations on your monitor 2006 GLOBAL VR All Rights Reserved T 9 Once the game Is powered on and you can see the attract mode running open the Coin Door and press the test switch to enter the operator menu Use the operator menu to adjust the amount of coins needed to start a game to turn redemption on or off for the cabinet and set the sound levels for your location Please read through CHAPTER 3 OPERATOR MENU for more detailed information about setting up the software features on your Feeding Frenzy cabinet 2 2 FISH PANEL INSTALLATION Follow the below steps to setup and fill the fish panel with water on the side of the cabinet 1 Begin by opening up the rear cabinet door to get access to the air pumps Next unplug the air hose from the one way air valve from the side that goes to the air pump as shown by the arrow in the picture below Do not unplug the hose that goes to the fish panel as water will begin to leak when you fill the Fish P
25. rator menu You will need to set the sound volume attract mode volume game difficulty coin settings and redemption settings You should play one complete game to ensure the correct operation of the cabinet s hardware Feeding Frenzy requires a USB HASP Security Dongle to activate the game software The Feeding Frenzy game dongle plugs directly into the USB ports on the computer When the USB Dongle is installed and working properly a red LED light will illuminate inside the dongle In order for a USB HASP Security Dongle to be recognized correctly it must be inserted into the USB port before the cabinet is powered on If for some reason the USB dongle is not recognized power the cabinet off then on to see if this resolves the problem 1 8 Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 4 2 TROUBLESHOOTING 4 2 1 Video Troubleshooting Problem Cause No picture on Power problem monitor Bad video cable Bad chassis PCB Picture is out of color Picture is dim or or misaligned faded Picture is out of color Picture geometry is misaligned Distorted colors on screen 2006 GLOBAL VR All Rights Reserved Possible Solution Verify the AC power connection to the monitor You can verify that the monitor has power by looking for a small glow in the neck of the CRT Verify that the video cable is firmly connected from the monitor to the video port on the computer While the monitor is powered ON unpl
26. rsonnel Specific warnings and cautions will be found throughout this manual where applicable We recommend that you read this page before preparing your Feeding Frenzy for game play Use the following safety guidelines to help protect the system from potential damage and to ensure your personal safety e To help avoid damage to the computer be sure the voltage selection switch on the power supply is set to match the AC power available at the location o 115 volts 60Hz in most of North and South America and some Far Eastern countries such as Japan South Korea and Taiwan o 230 volts 50Hz in most of Europe the Middle East and the Far East e To help prevent electric shock plug the system power cables into properly grounded power sources These cables are equipped with 3 prong plugs to help ensure proper grounding Do not use adapter plugs or remove the grounding prong from a cable If you must use an extension cable use a 3 wire cable with properly grounded plugs e To help protect your system from sudden transient increases and decreases in electrical power use a surge suppressor line conditioner or uninterruptible power supply UPS e Be sure nothing rests on the system s cables and that the cables are not located where they can be stepped on or tripped over e Do not spill food or liquid on your system e Do not push any objects into the openings of the system Doing so can cause fire or electric shock by shorting out interior comp
27. tion can be turned on or off The redemption ticket settings read from left to right as shown here with the menu below Award 01 ticket s every 200 fish points up to 2000 fish points then award 01 ticket every 400 fish points e Intelli Ticket when turned on will automatically adjust the difficulty of the game to dispense the amount of tickets in the target tickets per game setting e Ticket Frenzy will turn the game into full redemption mode where the goal of the game is to collect as many fish as possible in a set amount of time to earn the most tickets from the game Rode mption OFF Averd i 073 1 E TIKE Every amp ach fe Fish Points SE HNG Up tof 2000 FE Fish Points Thon Anard i G Tickells Every CUM Car Points IntelliTicket om Turgel Tickels Per Game i0 Ticket Frenzy OFF iL Ticket Frey Time Limt t00 C Rack 3 3 6 Tournament Settings When world high scoring is turned on the cabinet s game settings will automatically be adjusted to the match the tournament server s game settings The location city and state will be displayed along with the players name in the high score table to show where people are placing high scores e Location Enter the name of the location running the cabinet in this space e City and State Enter the city and state the cabinet is located in Location Sattings REL Tournamont Sottings Loc Address JAI IRCLE COURT Loc Name UDTRACADES Loc Phone 855 555 5555 Cit
28. tor Menu Features in Feeding Frenzy o Intelli Tune allows the operator to set an average play time for the game Intelli Tune will then automatically adjust the difficulty of game play so that a beginner or expert player s average play time meets the operator s desired settings o Intelli Ticket allows the operator to set the average amount of tickets dispensed in a redemption game Intelli Ticket will then automatically adjust the redemption settings so that the average amount of tickets dispensed per game meets the operator s desired setting 2006 GLOBAL VR All Rights Reserved 5 1 6 CABINET MODELS amp FEATURES Feeding Frenzy comes in 2 cabinet models a 27 VGA custom cabinet and a 19 34 height VGA cabinet designed around the average height of a 10 year children All the cabinets share similar components but each one will have a slightly different set up and service procedure Unless otherwise noted the procedures in this manual apply to all models Feeding Frenzy 27 Inch Cabinet Approximate Weight 250Lbs Feeding Frenzy 19 Inch Cabinet Approximate Weight 200Lbs Hardware Features e Intel Pentium 4 Computer e 640 x 480 VGA Flat Screen Monitor e Ticket Dispenser for Redemption Play e Aquatic Bubbling Fish Panels on both sides of cabinet Feeding Frenzy System Operator Manual 040 1001 01 Rev B 7 5 2006 Chapter 2 GAME SETUP 2 1 PRE GAME INSTALLATION Use the following steps to setup a new
29. ty fluorescent Verify the fluorescent tube pins make a good connection fixture with the lamp fixture Check the ballast for proper operation Improper amount of Incorrect setting in Go in the Operator M enu and verify the coin settings and credits given when operator menu adjust them as necessary coins or bills are inserted Faulty wiring Turn off the cabinet Verify that all the wires are firmly connected to the coin mech and bill validator Verify that no wires are frayed or improperly shorting to ground Game will not accept Faulty coin mech Verify the coin mech is not jammed Make sure the coin coins or bills mech is properly aligned and latched to the coin door Faulty bill validator X Verify the bill validator is powered on and working If the bill validator is faulty it will usually blink an error code on the inside of the coin door 2006 GLOBAL VR All Rights Reserved 23 4 3 CABINET SPECIFICATIONS If you need replacement parts use the part numbers listed below when you contact GLOBAL VR Tech 24 Support Table 1 Cabinet Parts List Description M anual Feeding Frenzy Operator Cable AC Power Standard Cable Audio 3 5 Mini Stereo 3ft Ethernet CAT 5 Blue 7 Feet Cable CD ROM IDE 40 PIN ATA 33 Cable Printer 6ft M olded Cable USB A A M to M 6ft w Velcro Aquarium with Fish Light and Pump Funnel with 4 Inch Plastic Hose Computer Power Supply ATX 250watt Computer M otherboard ASUS P4P8
30. ug the video cable from the monitor You should see a message on screen saying No Signal to verify the monitor is working Verify that the fuses on the chassis PCB are good Use the monitor control panel to adjust the brightness and contrast settings Use the monitor control panel to adjust the red green and blue color settings Use the monitor control panel to adjust the height and width as well as other geometric adjustments to see if this corrects the problem Press the degauss button on the monitor control panel to see if this corrects the problem 19 20 4 2 2 Audio Troubleshooting Problem No audio Audio is distorted or muffled Bad sound channel Cause Possible Solution Volume setting Enter the Operator Menu and adjust the volume setting for the cabinet Verify that the attract volume Is ON Bad wiring Turn off the cabinet Verify that all the wires are firmly connected to each speaker Verify that no wires are frayed Or improperly shorting to ground Blown speakers Remove the speaker s grill covers and visually inspect each speaker is in working order Run the Sound Test from the Operator M enu to verify each speaker is working Bad UGCI P You can verify the UGCI P is working by installing it into another working cabinet If that is unavailable to you plug a simple computer speaker into the audio ports on the computer and verify that sound is working from the computer Blown speakers Remove t
31. y SAN JOSE Web Password lt HIDDEN gt c State CA 3 3 7 Location Settings Use this menu to set the location address and phone number for the cabinet The address bar highlighted in grey can be edited select the press button to edit another address bar The location address and location phone should be the street address and phone number the cabinet is located at Web password should be reset to a selection of your choice 2006 GLOBAL VR All Rights Reserved 1 5 Statistics Coins Dropped 182 Tickets Awarded Ticket Average Garne Player starts 2 Player Starts Continues Average Play Per Coin 34 Lifetime Coins 182 Last Reset Date Thu Sep 08 13 57 48 2004 Dump to USB Key Reget Statistics The statistics menu shows the accounting information for the cabinet The coins dropped is then broken down into the number of one player two player and continues played The tickets awarded shows the total amount of tickets dispensed and the ticket average per game breaks down the total tickets into an average per game The average play per coin shows the average amount of time a game lasts Lifetime coins shows the total amount of coins dropped even after you have reset the statistics Dump to USB key allows you to save the statistics information to a USB flash memory device The reset statistics button is used to zero out the statistics info when selected the last reset date will be updated to the current date and t
Download Pdf Manuals
Related Search