SERVICE MANUAL MODEL SSP-373-D
Contents
1. GENERAL DESCRIPTION 21 2 2 2 3 2 4 The CEECO Model SSP 373 D Automatic Dialing Telephone is a microprocessor based typical elevator style telephone housed in a rugged stainless steel case The telephone is designed to provide typical elevator type service When the handset is lifted one or two separate telephone numbers depending on user programming of up to twenty five digits may be automatically dialed This telephone is also designed to deter fraudulent calling attempts The transmitter is muted during periods of dial tone to deter fraud Attempts to flash dial will cause the microprocessor to go on hook until the attempt has ended It will then seize the line and dial any programmed number s Incoming calls are not allowed Programming is accomplished via an internally mounted DTMF keypad CEECO 4 Communication Equipment amp Engineering Company PROPRIETARY 3 0 ISSUE 4 0 PROGRAMMING 3 1 3 2 3 3 3 4 3 5 3 6 Remove the stainless steel assembly from the mounting box if purchased together It will be necessary to use the security tool sold separately as CEECO part number 301 037 to remove the security screws Connect the telephone s modular cord to a DTMF test set or a working telephone line Looking at the rear of the phone connect the programming keypad to the white connector which is hanging freely inside the phone This connector attaches to seven different colored wir2. manner consistent with the urgency of the situation Please contact customer service for instructions regarding exchange of modules or printed circuit boards CEECO 12 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 11 0 WARRANTY POLICY 11 1 GENERAL CEECO products are guaranteed to be free of defects in material and workmanship for a period of 12 months from the date of original shipment if properly installed and maintained This warranty is limited to the value of material only CEECO will repair or replace any unit during this period if found to be defective for reasons other than abuse and improper use or improper installation It is the buyer s responsibility to return the defective unit to the factory CEECO will then repair or replace any defective parts and return them to the buyer free of charge PRINTED CIRCUIT BOARDS Printed circuit boards should not be field repaired If a unit is found to be faulty replace it with another unit and return the faulty unit to CEECO for repair Modifications by anyone other than CEECO will void the warranty CEECO 13 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 12 0 DIAGRAM Locate the mini jumpers on the corner of the PCB NS x Move the mini jumpers to the ON position BEFORE going off hook SN When programming is completed move the mini jumpers to the OFF position NOTE Do not leave the mini jump
3. Hang up the phone and return the two plastic mini jumpers to the OFF position as depicted on the last page of this manual The phone is now ready for Testing Operation CEECO 6 Communication Equipment amp Engineering Company PROPRIETARY 4 0 5 0 ISSUE 4 0 TESTING OPERATION 4 1 4 2 4 3 4 4 With the phone connected to a working phone line or a DTMF test set lift the handset The telephone will wait for dial tone When dial tone is detected any number programmed as the first auto dial number memory location 19 will be dialed The handset transmitter should be muted off until dialing is complete If the intended number does not dial out repeat sections 3 3 3 5 and 3 8 only If this does not solve the problem refer to section 10 2 please If there is a second number to auto dial memory location 20 the phone will either wait for the return of dial tone or wait the appropriate time depending on the programming selected under Location 00 Digit 2 and Digit 3 and dial that second number Remember that Digit 1 under Location 00 must be set to 1 for Location 20 to be enabled If the second number does not dial out repeat sections 3 3 3 5 3 6 3 7 and 3 8 If this does not solve the problem please refer to section 10 2 Normal phone operation should follow Have the called party hang up Wait for the central office equipment to time out and return dial tone Shortly after dial tone is received thr
4. QUANTITY PART NUMBER DESCRIPTION 1 1 OPTIONAL 371 008 371 014 928 001 945 001 341 018 371 009A 650 541 371 011 371 012 406 019 301 037 Stainless steel panel Handset with coiled cord amp magnetic plate Strain relief bushing Magnetic reed switch assembly Modular cord Mounting support bracket MCRK 2 PCB Assembly Mounting box Frame assembly for mounting box 10 32 x 4 Security screw 4 req d Security tool CEECO 10 Communication Equipment amp Engineering Company PROPRIETARY 9 0 ISSUE 4 0 FCC NOTICE 9 1 9 2 9 3 FCC REGISTRATION AND REPAIR INFORMATION Your new telephone has been registered with the Federal Communication Commission FCC in accordance with Part 68 of its rules The FCC requires that you be advised of certain requirements involving the use of this telephone CONNECTION AND USE WITH THE NATIONWIDE TELEPHONE NETWORK The FCC requires that you connect this telephone to the Nationwide Telephone Network through a registered jack provided by the Telephone Company in your area This jack is a modular outlet which you can order from your local telephone company NOTIFICATION TO THE TELEPHONE COMPANY Before connecting this telephone the FCC requires that you notify your local telephone company business office The number is in the front of your phone book Tell them The line to which you will connect the telephone that is your phon
5. assembly into the RJ11C modular jack or terminal block Dress the line cable away from the mounting holes Install the telephone assembly by placing it into its mounting box and securing it with the four security screws The security tool CEECO part number 301 037 sold separately will be needed Never install telephone wiring during a lightning storm Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface Use caution when installing or modifying telephone lines CEECO 8 Communication Equipment amp Engineering Company PROPRIETARY 7 0 SPECIFICATIONS INPUT POWER LOOP CURRENT IMPEDANCE SIGNALING HEARING AID COMPATIBILITY ENVIRONMENTAL TELEPHONE PANEL DIMENSIONS MOUNTING WEIGHT RINGER EQUIVALENCY FCC REGISTRATION NO UL LISTED NO TYPE JACK CEECO ISSUE 4 0 C O Line Powered 23 mA min to 80 mA max 600 ohms DTMF 70ms tone 50ms spacing Meets EIA standards Temperature 0 C to 50 C Humidity 20 90 non condensating Brushed 16 gauge stainless steel 6 7 8VW x 9 3 4VH x 3VD handset on hook Vertical surface or enclosure mount Approximately 4 lb 0 8A BW 88T7 13717 TE T 60F5 RJLIC Communication Equipment amp Engineering Company PROPRIETARY 8 0 PARTS LIST ISSUE 4 0
6. SSP 373 D ADI2 01 650 541 ISSUE4 0 SERVICE MANUAL FOR MODEL SSP 373 D STAINLESS STEEL ELEVATOR AUTOMATIC DIALING TELEPHONE EQUIPPED WITH ADI2 01 FIMWARE Communication Equipment 519 W South Park Street amp Engineering Company Okeechobee FL 34972 Voice 863 357 0798 Fax 863 357 0006 Serving the Telephone Industry Since 1930 ISSUE 4 0 IMPORTANT INFORMATION FOR CUSTOMER Please fill in before you continue The following information is necessary when calling CEECO for assistance MODEL NUMBER MODEL SSP 373 D EQUIPPED WITH ADI2 01 FIRMWARE SERIAL NUMBER DATE MANUFACTURED LOCATION INSTALLED For us to better serve you please have this information available when calling for technical support CEECO Communication Equipment and Engineering Company 519 W South Park Street Okeechobee FL 34972 863 357 0798 telephone 863 357 0006 facsimile info ceeco net www ceeco net CEECO 2 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 TABLE OF CONTENTS SECTION PAGE 1 0 INFRODU CUION vsicastincisccssecscasiccscacecsevedestessceabesaghiseoonsdedssonsqusessshedbsnnedsctoanpndabtanses 4 2 0 GENERAL DESCRIPTION vissccssccciossssisssecesccvontsonssdecnossventasscaneceniveoesscevedsecsteszonss 4 30 PROGRAMMING ccoiisiisssstissosesessesisscssssoesssosssotssosooes ososi osis sosoo sesosok SaDa o KESS 5 PROGRAMMING CONTINUED sicasssecrasesasacacinesienac
7. ake selections for Digits 2 and 3 accordingly Location 19 must be used in order to use Location 20 CEECO 5 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 PROGRAMMING CONTINUED 3 7 3 8 EXAMPLE Entering 2019545875430 on the programming keypad will cause the phone to automatically dial the number 1 954 587 5430 when the handset is lifted e Be sure to record your number in the Location 20 Table below for future reference LOCATION 20 TABLE SCENARIO Location 19 might be programmed to dial 9 for an outside line Location 20 might be programmed to dial 1 800 555 1212 after the outside line is established The programming sequence would be 199 2018005551212 which is entered on the programming keypad Enter 0 0 on the keypad This accesses the telephone options programming location Now enter three digits which you will select from the options below to customize the phone for the particular installation Digit 1 0 Do not dial the number in location 20 1 Dial the number in location 20 Digit 2 0 Wait for dial tone before dialing the number in location 20 1 Wait for 1 9 seconds depending on digit 3 below before dialing number in location 20 Digit 3 1 9 Number of seconds to wait before dialing number in location 20 e Be sure to record your selections in the OPTIONS TABLE below for future reference OPTIONS TABLE 00 _ _ Programming is now completed
8. cntane cera iiideracacianerarantapatac 6 AO TES TING OPERA TION ssssscsssstvenssssuses spoucyssessistebstetausncssbossnvavsadescmuasassceuteas evasseuede 7 5 0 RECOMMENDED TOOLS AND TEST EQUIPMENT 7 6 0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 8 T0 SPECTEICA TIONS wiicsacscesessscscsssecedsscasstscsesncscabesdeds c seudedsbass sondo serios sssi ioia soss 9 8 0 PARTSLISE asrespeaas seo anais atado sina adia io pisada dadas cad conetesdcatesvedaceusisacseuspocenes 10 90 FECONOTICE sia E do jo pitanga Rad aa aj ai E 11 10 0 REPAIR AND RETURN INFORMATION ccsssssccsssssecccsssssccsscscccssones 12 11 0 WARRANTY POLICY sisiscssccsssssachvasarsessnendstesscsnsesstbeovevsiedssosnausencaueetussessexentevenses 13 120 DIAGRAM assento iniciasse istos isoce ssepe osoo sr seee cicacan soco uterino can ossee eeose se arets 14 CEECO 3 Communication Equipment amp Engineering Company PROPRIETARY 1 0 2 0 ISSUE 4 0 INTRODUCTION The practices in this manual provide installation and maintenance information for the Model SSP 373 D Stainless Steel Elevator Automatic Dialing Telephone The information in this manual is subject to change without notification For information not included in this manual please call or write CEECO Customer Service 519 W South Park Street Okeechobee FL 34972 863 357 0798 telephone 863 357 0006 facsimile info ceeco net Www ceeco net
9. e number the telephone s FCC registration number and ringer equivalence number These numbers are listed in section 7 0 The FCC further requires that you notify your local telephone company when permanently disconnecting this telephone CEECO 11 Communication Equipment amp Engineering Company PROPRIETARY ISSUE 4 0 10 0 REPAIR AND RETURN INFORMATION 10 1 10 2 10 3 10 4 10 5 WARRANTY REPAIR Any device returned requiring warranty service repair or credit must be accompanied with a Return Material Authorization RMA Form It must include return shipping instructions original purchase order number and special marking instruction A description of the trouble observed must be attached to the defective unit This information must be inside the original shipping container DIRECT ALL INQUIRES TO CEECO Repair Department 863 357 0798 telephone 863 357 0006 facsimile info ceeco net Www ceeco net NON WARRANTY REPAIR CEECO will repair equipment out of warranty for a set charge plus parts The customer must pay the shipping costs both directions RETURN FOR CREDIT Material may be returned for credit only with prior approval Material authorized for return is subject to a 20 restocking charge based on the manufacturer s list price Return RMA must be requested no later than 30 days after original shipment EXCHANGE POLICY If a replacement unit is required it will be shipped in the most expedient
10. ee tones should be heard The phone will open the line and remain in this condition until the handset is placed on hook The handset transmitter and receiver will be disabled during this period Attempt to hookswitch dial by tapping quickly on the hookswitch The telephone should hang up seize the telephone line and dial the programmed auto dial number s when dial tone is received again RECOMMENDED TOOLS AND TEST EQUIPMENT DTMF Test Set Volt Ohm Meter 1 4 Nut Driver 5 16 Nut Driver Flat Blade Screw Driver Security Tool 301 037 CEECO 7 Communication Equipment amp Engineering Company PROPRIETARY 6 0 ISSUE 4 0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 6 1 6 2 6 3 6 4 The SSP 373 D is designed to be mounted inside any apparatus box with dimensions of 6 7 8VW x 9 3 4VH x 3VD or greater CEECO part number 371 011 is an apparatus box which is well suited for this purpose Four mounting holes are required inside the box If the holes are not tapped then self tapping screws should be used when mounting the panel It is best to use the security screws which do require tapped mounting holes Mount the two mounting support brackets provided to the apparatus box being used Route the inside station wire and terminate to an RJ11C modular jack or terminal block The use of a gas tube station protector is recommended The station ground should not exceed 50 ohms Plug the modular line cord from the telephone
11. ers in the ON position this will decrease battery life CEECO 14 Communication Equipment amp Engineering Company PROPRIETARY
12. es and has a similar end which is already connected to the Printed Circuit Board Locate the two plastic mini jumpers on the corner of the Printed Circuit Board and move them to the ON position as depicted on the last page of this manual Lift the handset and wait for dial tone Utilizing the programming keypad enter 9 7 on the keypad This will clear all field programmable memory NOTE During programming it is essential to press the keys deliberately and slowly Missed or partial tones will result in improper programming If the phone must automatically dial a number when the handset is lifted enter 1 9 on the programming keypad followed by the desired number of up to twenty five 25 digits in length Once programmed this number will always dial when the handset is lifted EXAMPLE Entering 1918005551212 on the programming keypad will cause the phone to automatically dial the number 1 800 555 1212 when the handset is lifted e Be sure to record your number in the Location 19 Table below for future reference LOCATION 19 TABLE If the phone must automatically dial a second number when the handset Is lifted enter 2 0 on the programming keypad followed by the desired number of up to twenty five 25 digits in length In order for the phone to dial the number stored in the 20 programming location you must select a 1 for Digit 1 under the 00 programming location refer to next section 3 7 You must also m
Download Pdf Manuals
Related Search