巻取／繰出装置 補足説明書 - mimaki engineering co., ltd.
Contents
1. sat ee TORE ne AS 14 FF 14 2 0 14 SN u 21 14 ZEN 14 OFF Q amp A P 2 9 P3 4 P2 342. P3 5 14 1 6m 1 6m 2 20 27
3. BSE 1 ZEN 1 14 AK
4. O 1 FUNCTION FUNCTION lt ENT gt 2 QOQ CENTER Wy Byes lt ent gt 3 ED amp CENYER amo lt ent gt 4 ED EO CENTR a we 5 E23 EDT CENTER 6 CEN5 2 014
5. 2 25 l Q amp A P2 20 P3 4 P2 34 P3 5 P3 24 This manual describes the se
6. LOW them two by two while checking the Tarpaulin platen Adjust from 0 to 14 pcs feeding The roll being take Take up Feeding l HIGH up is wrinkled 14 pcs each Transfer Take up Feeding Print Pre heater LOW pager 14 pcs each 5 OFF Recommended setting Heavy duty Take up Feeding device Trouble for feeding Q amp A Set the media correctly See Operation Manual P 2 9 Set the media in the center of this machine Setting media on one side or the other may cause skewing Media skewing Perform media compensation See Operation Manual P 3 4 or White lines black lines in the head cleaning See Operation Manual P 2 34 lateral direction After compensation adjust the feed during printing as needed See Operation Manual P 3 5 Set Tension bar active position any and Number of the weight Blurred white stripes in the 14 each and adjust media feeding lateral direction If the trouble does not solve after the adjustment above set the print heater temperature to low Narrow Take up Feeding device This machine is equipped with the narrow take up feeding device for media with less than 1 6 m wide If media with less than 1 6 m wide is set on the heavy duty take up feeding device the media is not correctly fed Use the narrow take up feeding device Read Operation Manual P 2 20 to 27 with care and set the media correctly Adjust the torque limit
7. AA mak JV34 260 JV34 260 Series Take up Feeding Device Supplement JV34 260 Thank you very much for your purchase of the JV34 260 series JV34 260 1 2 e Wy MN
8. er to adjust take up tension of the media Turn the adjustment knut clockwise to increase the tension and turn it anticlockwise to decrease the tension See Operation Manual P 2 25 for details Narrow Take up Feeding device Trouble for feeding Q amp A Set the media correctly Media skewing See Operation Manual P 2 20 Setting media on a skew may cause skewing Perform media compensation See Operation Manual P 3 4 or White lines black lines in the head cleaning See Operation Manual P 2 34 lateral direction After compensation adjust the feed during printing as needed See Operation Manual P 3 5 Set the print heater temperature to low PVC media is wrinkled on the Adjust the torque limiter to increase the take up tension of the platen and the image is printed media with poor quality Set the media adsorbing power on the platen to STRONG See Operation Manual P 3 24 AA mak Printed in Japan D202196 10 15022011 MIMAKI ENGINEERING CO LTD 2011
9. to the weight arm on the left of this machine 0 to 14 pcs each on the take up side 7 feeding side Important To adjust the take up tension bar weight install the weight on the back of this machine To adjust the feeding tension bar weight install the weight on the front of this machine Attach the weight with care because it is very heavy Attach the weight one by one Recommended settings for each media The followings are recommended settings of the active position of the tension bar or number of the weight for each media Important e Check the following recommended settings before setting When media is correctly fed the following settings are recommended TensionBar POS LOW Number of the weight 14 pcs each When adjusting media while using the heavy duty take up device feeding device check the compensation pattern near the center of the platen and enter the compensation value If checking the pattern near the station it may not be adjusted correctly sly By the condition as media type ink density or printing speed optimum condition as the active AS position of the tension bar or number of the weight varies Adjust properly for the environment used Media type Media feed pension Dar Number of the weight Note active position No problem LOW dake nes Peeding Recommended setting 14 pcs each FF Media sticks to the Take up Feeding tacih Welds ang ee
10. ttings for the various media used for JV34 260 series to be fed stably Read this manual carefully and use the take up feeding device with the proper settings for each media Adjustment function of Heavy duty Take up Feeding device 1 Select an active position of the take up tension bar Select an active position of the take up tension bar from two options HIGH or LOW A When LOW is selected for the active position When HIGH is selected for the active position NT The active position of the take up tension bar is set to LOW before shipping AE When the roll being take up is easy to be wrinkled it is recommended to set to HIGH How to set an active position of the tension bar Set an active position of the tension bar as follows 1 Press the key in the local mode FUNCTION SETUP lt ENT gt 2 Select MACHINE SETUP by pressing the keys and press the WACHINE SETUP CENTER key DRY FAN lt ent gt 3 Select Feeding TakeUP by pressing the keys and press the g TakeuP CENTER key UNIT SELECT cent 4 Select TensionBar POS by pressing the keys and press the Tr g TakeuP CENTER key TensionBar POS LOW gt 5 Press to select HIGH or LOW and press the key 6 Press the key several times to end 2 Adjust the weight of the tension bar The weight of the tension bar can be adjusted by attaching the weight accessory to the bar Attach the weight
Download Pdf Manuals
Related Search