INSTALLATION & OPERATING INSTRUCTIONS MODELS
Contents
1. 6 12 VDC only Select a location with minimum of curvature on roof of vehicle Press light into place making sure that outer gasket conforms to surface If you are using this light over bumpy roads it is suggested that you install the screw provided to engage the moveable keyhole bracket for a more secure installation BROWN REPLACEMENT PARTS LIST PART DESCRIPTION _ MV amp MV IND MV MAG Oooo RED 200502 pO BE 20 0506 e c H I I I ee __ o a o o O o oo o a T o O Vie 42 0620 at Vid oo O Ot O a 9 82068 O TOT 250 0822 NA a 5 E e E a E T o O e O o O OYO SINGLE CONTACT LAMP DOUBLE CONTACT LAMP x42 0336 MAY BE USED FOR LONGER LIFE LESS LIGHT SPECIFY 36 VDC INCLUDE 60 3001 DROPPING RESISTOR 950096 Rev 7 98 1642 No Besly Ct Chicago IL 606226 773 384 7765 e Fax 773 384 5115 ah INSTALLATION amp MOUNTING INSTRUCTIONS MODELS MR 3 MR 3H Use only with 12 VDC vehicle supply voltage Use attached magnets for mounting to ferrous metal surfaces Use included VELCRO for other applications Select the flattest available surface for mounting Use only 12VDC cigarette lighter socket for supply power To replace motor or lamp remove outer dome retaining band remove dome and replace parts as needed Use care in handling dome retaining ring to avoid damage Ime Na REPLACEMENT PARTS LIST PART CCST DESCRIPTION CPR hee ee RED po GREEN 20 0404 Re BEE 180006 po RBH 420302 po2. LARGE 8ST 42 0336 MAY BE USED FOR LONGER LIFE LESS LIGHT LIMITED WARRANTY If it appears within one 1 year from the date of delivery to Purchaser that any products or component parts do not conform exactly to the specifications and physical dimensions referred to above and the Purchaser at its expense returns the product or component parts to the Seller together with a report of defects the Seller shall review the inspection report and inspect the items and shall authorize at its option either the repair or replacement of any non conforming products or component parts whether on warranty contract of negligence shall not in any case exceed the amount to be paid by the Seller in obtaining and repair or replacement of non conforming products or component parts and upon expiration of the warranty period all liability of the Seller shall be terminated Seller shall not be liable for any injury loss or damage direct or consequential arising out of the use or the ability to use the product This warranty gives specific legal rights You may have other rights which vary from state to state Some states do not allow the exclusion or limitation of incidental or consequential damages so that the above limitation of exclusion may not apply to you WARNING The individual user should take care to determine prior to use whether this device is suitable adequate or safe for the use intended Since individual applications are subject to great va
3. riation the manufacturer makes no representation or warranty as to suitability or fitness of these devices for any specific application 1642 No Besly Ct Chicago IL 606226 773 384 7765 e Fax 773 384 5115
4. va INSTALLATION amp OPERATING INSTRUCTIONS G z MODELS MV MV IND amp MV MAG MV MV IND PERMANENT MOUNT MODEL Follow drawing on back showing views of mounting and belt drive systems Select location on vehicle which will be permanent for mounting light Drill a hole that will just pass the 4 in screw protruding from the rubber shock mount in base of light Use the proper number of in flat washers to take up space and enable you to fasten light securely to roof The unit is equipped with a flexible skirt gasket which conforms to curves in the vehicle roof Be sure this gasket is fully engaged with roof to prevent water leakage 5 To RELAMP or REPLACE MOTOR loosen two screws holding dome retaining clips at side of light and remove dome To RELAMP Depress bulb in socket and rotate counter clockwise to remove Reinstall by reversing the process Be sure to use the proper lamp by referring to below parts list To REPLACE BELTS Simply remove and replace To REPLACE MOTOR Remove the dome clips and lift aluminum housing from steel base cup Remove small retaining clip holding reflector assembly using a small flat blade screw driver Be sure to save this C shaped clip for reinstallation Lift off reflector assembly remove and replace motor Be sure to observe wiring before disconnecting motor wires In the case of a 12 volt motor you will find only one wire as the motor case serves as a return path for the power MV MAG magnetic mount
Download Pdf Manuals
Related Search