Electrician Installation Manual National Warranty Line
Contents
1. PACIFIC INTERNATIONAL Electrician Installation Manual CEILING FANS EM E Ceiling Fan SME pe N fi vo pm ZTA CEILING FAN MUST BE INSTALLED BY A LICENSED ELECTRICIAN NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN Electricians are recommended to tick off all items on the quick checklist and fill out their details onto the back page of the Fan Owner Warranty amp Operations Manual after installation ELECTRICIANS TO PROTECT YOUR CUSTOMER S WARRANTY PLEASE READ PAGE 2 OF THIS BOOKLET PRIOR TO THE INSTALLATION OF THIS PRODUCT National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia Pacific International Fans Pty Ltd Building 8 256 New Line Road Dural NSW 2158 Australia PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan IMPORTANT INFORMATION ELECTRICIANS MUST READ PRIOR TO INSTALLATION Distributor and installer details and purchase receipts are essential for on site warranty claims and must be presented to repair personnel make sure you record your details in the Fan Owner Warranty and Operations Manual Fans and fixed wiring products must only be installed by persons who are appropriately licensed by the applicable State regulatory body Therefore to protect our repair personnel on site warranty claims will not be accepted if products have been installed by unlicensed persons Damage caused by incorrect installation for2. used Cap seal light wires if a light fitting is not going to be used Green yellow O E m 5 8 D E T ci i S D Combi Separate F 5 Control Control FA LAE N a Separate terminal Fan Wiring Wiring for use with 3 pole block For when 3 pole Colours representative only Block is fitted Separate extension terminal for active for light when 3 pole block fitted STEP 5 Fig 6 a Slide canopy cover up and over the hanger bracket b Twist the canopy to locate screws holes then loosen canopy screws half way c Now twist the canopy cover in the opposite direction and fully tighten screws until the can opy cover is stabilised Bracket Down Rod 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Pacific International Fans for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty e 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If eee only one blade is damaged you arg still required to replace with a new set PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan Assembling the fan STEP 6 Fig 7 a Attach blades to the blade holders inside the motor housing using the 3 screws and po washers provided Blade b Repeat this procedure for the other 3 blades Blade Washer Blade Screw STEP 7 Fig 8 a Lift th
3. Check the fan is operating correctly on all three speeds using the wall controller If light is installed Check light switch is functioning properly If remote control is installed Check the fan and light if installed is responding to the remote control correctly Write Dip switch code in user guide If remote control is installed A separate isolation switch has been installed on the supply side of the remote control receiver Check electrician s details have been recorded onto the back page of the Owner s Operations and Warranty Manual 14
4. turn it to attach the light glass to the fan 2 WARNING E14 light MAX 2x40W a a Lower Rim STEP 1 Fig 12 a Turn base plate to remove the plug and base plate from the motor housing b Loosen screws to remove the lower rim Light wire connectors Lower STEP 2 Fig 13 a Use the connectors to attach the light wires from the motor housing to light assembly kit b Attach and secure the light assembly kit using the 3 screws provided _____ Glass Cover STEP 3 Fig 14 a Install the light bulbs in the light sockets b Gently push the glass cover upwards and turn it to attach the light glass to the fan Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Pacific International Fans for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you arg still required to replace with a new set PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan C E ILING F AN S Attaching an accessory light kit EM E light kit GX53M 14W fluorescent light STEP 1 Fig 15 a Turn base plate to remove the plug and base plate from the motor housing b Loosen screws to remove the lower rim Screws Lower Rim STEP 2 Fig 16 a Use the c
5. ONAL Electrician Installation Manual EM E Ceiling Fan LIN G FANS Trouble Shooting Tips Light Light will not turn on Make sure globe has not blown and it is properly fitted between the metal prongs Check all light wires in the light kit the terminal block in the canopy cover and the wall switch have been connected together correctly Light is not responding to remote control Make sure globe has not blown and it is properly fitted between the metal prongs Check all light wires in the light kit the terminal block in the canopy cover and the wall switch has been connected together correctly Check dip switch settings in remote hand piece and remote receiver correspond Light wires appear to be missing or too short Wires may be stuck in the motor housing Carefully pull wires out of the motor housing being careful not to damage or strip the wires going to the motor windings as this may cause the fan to short Light flickers or flashes Check globe is secured between the metal prongs in the light kit Make sure you are using the globes specified Compact fluorescent globes may not be compatible with dimmer style remote controls use energy saving encapsulated halogen types instead National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia approved by Pacific International Fans for use with its fans DO NOT use solid state 1 Do not attempt to operate the fan or optional lig
6. at the reversing switch is pushed into its Summer or Winter position Fan is not responding to the remote control Check for flat battery Make sure the dipswitch settings in the hand piece and the remote receiver for the same fan are corresponding Fan is wobbling Check the ball joint slot is locked into the hanger bracket groove Make sure blades are a matching set the letters on matching sets of blades should be identical with the numbers varying within 3 grams of each other Check blade screws are tightened firmly If necessary use balancing kit provided to settle the wobble Fan is noisy 1 2 WARNING Check all screws and parts are secured firmly Ensure there are no loose parts moving inside the motor housing Make sure the fan is installed with a Pacific International Fans wall controller only do not use solid state controllers as they can cause unpleasant motor noises National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Pacific International Fans for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 12 PACIFIC INTERNATI
7. ce majeure electrical surges lightning power grid fluctuations water or by connection to alternative power supply sources such as solar inverters etc is not eligible for warranty repair Blades must be replaced only as a complete set Blades are supplied only as a pre balanced set and the replacement of individual blades may void the warranty by causing mechanical damage to the motor excessive noise or premature wear When products are installed in a location requiring special access equipment such as scaffolding or scissor lifts etc the cost of providing installing and operating special access equipment must be borne by the site owner For safety and to protect your customers warranty the following must be taken into account when installing and operating the product s a DO NOT USE SOLID STATE WALL CONTROLLERS Neither leading nor lagging edge controllers will give satisfactory performance Wall controls must only be types approved for use by Pacific International Ceiling Fans The fan light and bracket must be earthed Fan and light must be run from the same phase and preferably the same final circuit Mounting bracket must be firmly screwed to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts such as T hooks are available for certain types of installation After in
8. e switch cover to expose the reverse switch b The reverse switch should be pushed fully to the left for Summer fan spins anticlockwise and pushed fully to the right for Winter fan spins clock wise c Make the sure reverse switch is not stuck in its neutral position otherwise the fan will not spin 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Pacific International Fans for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty e 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If WARNING only one blade is damaged you are still required to replace with a new set PACIFIC INTERNATIONAL C E ILING F AN S Attaching an accesso Electrician Installation Manual EM E Ceiling Fan ight kits EM E light kit 78mm halogen light MAX 100W sdana Lower Rim STEP 1 Fig 9 a Turn base plate to remove the plug and base plate from the motor housing b Loosen screws to remove the lower rim STEP 2 Fig 10 a Use the connectors to attach the light wires from the motor housing to light assembly kit b Attach and secure the light assembly kit using the 3 screws provided Groove Glass Cover STEP 3 Fig 11 a Plug the light globe into the socket DO NOT touch the light globe with your fingers b Gently push the glass cover upwards and
9. eeds to be shortened cut the rod to the required length and drill the appropriate hole size to fit the ball joint pin The cut end of the rod should be used on the ball joint end only When installing a 1 8m extension rod the wiring will need to be extended and joined This should be done using crimp style connectors 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Pacific International Fans for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty e 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If Ebai only one blade is damaged you arg still required to replace with a new set PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan G F A N S Trouble Shooting Tips Fan Fan will not start Check that the reversing switch is pushed fully into its Summer or Winter position Check wire connections in the wall switch and terminal blocks ensure all wires are making proper contact Fan speed does not correspond to the wall controller Check the speeds on the wall controller has been wired correctly and are making proper contact Brown speed 1 Purple speed 2 Red speed 3 Check wires in the terminal block are connected properly connection wires should be stripped back at the connection point and unused wires should be sealed and capped off Check th
10. ght kit Terminal Block note Only specified globes should be used Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Pacific International Fans for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan C E ILING F AN S Attaching an extension rod genuine rods to be used ONLY Canopy Cover Reverse Switch Cover Washers a Cotter Key Fb Connection Collar Ball Joint Down Rod i Cotter Pin Screw t pe a Down Rod Step 1 Fig 24 Step 2 Fig 25 Loosen and remove the down rod screws and Loosen the ball joint screw take out the ball joint the down rod pin screw to remove the pin and remove the ball joint Then slide off the standard down rod from the motor housing canopy cover __ Ball Joint Canopy Cover Reverse Tighten Ball 7 Switch Cover Joint Screw Washer s a Cotter Key SI Connection Collar Down Rod Down Rod i E 7 Cotter Pin Screw Step 3 Fig 26 amp 27 Now install the extension rod and reverse step 1 amp 2 to secure the rod to the fan and the ball joint NOTE If the extension rod n
11. hread of the motor housing lower rim d Tighten screws removed from step 2 to Cut and remove secure the motor housing lower rim back wire connectors onto the motor housing upper rim a Thread Screw 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Pacific International Fans for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty e 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If eee only one blade is damaged you arg still required to replace with a new set PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan Attaching an accessory light kit a standard accessory light kit Thread Upper Part of Light Kit Lower Part of Light Kit 2 WARNING STEP 4 Fig 22 a Feed wires from the motor housing lower rim through the hole in the centre of the base plate b Attach the base plate to the motor STEP 5 Fig 23 a Feed wires through the thread of the upper part of the light kit b Secure upper part of the light kit to the motor housing by tightening the thread c Connect light wires to the terminal block in d Secure the lower part of the light kit to the upper part of the light kit by the tightening the light kit screws LF af the lower part of the light kit Wires e Fit light globes in to the li
12. ht kit with any wall control that is not WARNING controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you arg still required to replace with a new set PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan Quick Checklist Electricians make sure everything on this checklist is ticked off before you leave the installation site If you have trouble installing our product please refer to the trouble shooting section on the previous page first then phone the Warranty Line on 1300 360 280 open 9am to 50m EST DO NOT uninstall the fan and DO NOT return fan to retailer 10 Ceiling fan is not installed to a solid state wall controller Neither leading nor lagging edge controllers will give satisfactory performance Wall controllers must only be types approved for use by Pacific International Fans The fan optional fan light and bracket is earthed Fan and optional fan light are run from the same final circuit Mounting bracket must be firmly secured to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts such as T hooks are available for certain types of installation Fan blades are at least 2 1m feet above floor level
13. o be installed please go to page 11 Hanger STEP 2 Fi 2 Timber Nogging Bracket a Drill a hole in the timber nogging for wiring b Use the two hex screws to secure the hanger bracket onto the timber nogging The timber nog ging should be supplied by the installing electri cian and must be supported between the two ceil ing joists as shown in the diagram above Hex Head Screw STEP 3 Fig 3 a TIGHTEN THE GRUB SCREW This is important to ensure the fan will not wobble and the weight of the fan is supported b Hang the ball joint into the hanger bracket t Ensure the groove on the hanger bracket is Down Rod locked into the slot on the ball joint 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Pacific International Fans for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty e 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If eee only one blade is damaged you arg still required to replace with a new set PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan Assembling the fan STEP 4 Fig 4 amp 5 a Connect wires from the fan to wires in the ceiling via the terminal block on the hanger bracket refer to figure 4 and 5 b Make sure earth wires are also connected c Connect light wires red white if a light fitting is going to be
14. onnectors to attach the light wires from the motor housing to light assembly kit b Attach and secure the light assembly kit using the 3 screws provided Base Socket a B jano Glass Cover _Light STEP 4 Fig 18 STEP 3 Fig 17 a Turn the light to attach it firmly to the light a Fit the fluorescent light assembly to the socket base socket b Gently push the glass cover upwards and turn it to attach glass cover to the fan 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Pacific International Fans for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty WARNING 2 Do not mix blade sets from one fap to another as this may upset the balance of the fan If PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan C E ILING F AN S Attaching an accessory light kit Standard accessory light kit Lower Rim Base Plate mug Scien STEP 2 Fig 20 STEP 1 Fig 19 a Loosen screws to remove the light kit rim a Turn base plate anticlockwise to remove the plug and base plate from the motor housing Do not throw away base plate away STEP 3 Fig 21 a Once the motor housing lower rim is removed the light wires coming from the motor housing should be exposed b Cut and remove wire connectors c After removing the wire connectors feed the light wires through the t
15. stallation fan blades must be at least 2 1 m 7 feet above floor level The use of these products by children and the infirm must be under supervision IF THERE ARE ANY PROBLEMS WITH THE PRODUCT AT TIME OF INSTALLATION THE INSTALLER MUST CONTACT THE WARRANTY HOT LINE NUMBER 1300 360 280 BEFORE LEAVING THE JOB SITE PLEASE DO NOT REMOVE THE FAN FROM THE CEILING ONCE INSTALLED UNLESS INSTRUCTED TO DO SO PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan Parts List EM E Hex Head Screw Canopy Cover Housing Blade Screw oyen Joen o y esera neresen 2 Down Rod Pin Screw these parts come preassembled Down Rod Short Screw PACIFIC INTERNATIONAL Electrician Installation Manual EM E Ceiling Fan Assembling the fan STEP 1 Fig 1 Ball Joint PERFORM THIS STEP IF THE WIRES HAVE NOT Canopy BEEN FED THROUGH THE DOWN ROD a Loosen the ball joint screw and remove the Reverse ball joint pin to separate the down rod from the A ball joint Washers F b Feed wires from motor housing up and Cotter Key bee Connection Collar through the down rod Down Rod Ja Cotter Pin c Insert the down rod pin into the connection Screw 4 oat collar and the down rod cotter pin avoid pinch ing wires Clip in the cotter pin key and secure down rod with the other shorter down rod screw provided d Slide on canopy cover and refit the ball joint If an extension rod needs t
Download Pdf Manuals
Related Search