Electrician Installation Manual National Warranty Line
Contents
1. WARNING Ceiling fan is not installed to a solid state wall controller Neither leading nor lagging edge controllers will give satisfactory performance Wall controllers must only be types approved for use by Hunter Pacific International The fan optional fan light and bracket is earthed Fan and optional fan light are run from the same final circuit Mounting bracket must be firmly secured to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts such as T hooks are available for certain types of installation Fan blades are at least 2 1m feet above floor level If fan is installed on a wall controller check the fan is operating correctly on all three speeds using the wall controller If light is installed Check light switch is functioning properly If remote control is installed Check the fan and light if installed is responding to the remote control correctly If remote control is installed Check where possible a separate isolation switch has been installed for the fan Check electrician s details have been recorded onto the back page of the Owner s Operations and Warranty Manual 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The2. is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set Electrician Installation Manual Majestic Duo Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Assembling the fan CRON A STEP 1 Fig 1 amp 2 AN lt r Use the hex head screws to secure the hanger bracket onto the mounting plate optional and into com the timber nogging in the ceiling Timber nogging should be supported in between two ceiling joist as shown in the diagram below figure 2 Hanger Bracket Ball Joint STEP 2 Fig 3 With the ball joint attached to the down rod slot the ball joint into the hanger bracket Refer to page 6 for wiring instructions STEP 3 Fig 4 a Feed the fan wires from the adjustable arms joining point through the down rod and the ball joint b Then connect the adjustable arms joining point with the down rod using the screws provided c Now lock the ball joint onto the down rod using the ball joint pin carefully move the wires to the sides and avoid pinching them 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use
3. solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set Electrician Installation Manual Majestic Duo Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Assembling the fan Wiring Instructions Note 2 Wall switches are included for individual operation of the motor units Green yellow Separate Control Control Green yellow is one d Wiring for use with 3 pole block Separate terminal Ean Wiri Colours representative only T cole AV Separate extension terminal for active wire for light when 3 pole block fitted block is fitted gt 33 ai _ Hanger Bracket Le FIG 6 _ Canopy Cover Canopy Cover Screw STEP 4 Fig 5 a Slide canopy cover up and over the hanger bracket b Twist canopy cover as shown in diagram until the screws holes can be seen c Half loosen canopy cover screws d Now twist canopy cover in the opposite STEP 5 Fia 6 Take the motor unit and direction to the diagram and fully tighten the canopy covers screws this will stabilise the remove the knurled knobs as shown in the diagram above Canopy Cover 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hu
4. use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 11
5. Electrician Installation Manual Majestic Duo Ceiling Fan HUNTER PACIFIC INTERNATIONAL Majeste CEILING FAN MUST BE INSTALLED BY A LICENSED ELECTRICIAN NO OTHER PERSONS SHOULD ATTEMPT TO INSTALL THIS FAN After installation electricians must tick off all items on the quick checklist and fill out their details onto the back page of the Fan Owner Warranty amp Operations Manual ELECTRICIANS TO PROTECT YOUR CUSTOMER S WARRANTY PLEASE READ PAGE 2 OF THIS BOOKLET PRIOR TO THE INSTALLATION OF THIS PRODUCT National Warranty Line 1300 360 280 Monday to Friday from 9am to 5pm EST Only available within Australia Hunter Pacific International Pty Ltd Building 8 256 New Line Road Dural NSW 2158 Australia ABN 18 063 521 666 1 Electrician Installation Manual Majestic Duo Ceiling Fan HUNTER PACIFIC N TERNATIONAL IMPORTANT INFORMATION ELECTRICIANS MUST READ PRIOR TO INSTALLATION Distributor and installer details and purchase receipts are essential for on site warranty claims and must be presented to repair personnel make sure you record your details in the Fan Owner Warranty and Operations Manual Fans and fixed wiring products must only be installed by persons who are appropriately licensed by the applicable State regulatory body Therefore to protect our repair personnel on site warranty claims will not be accepted if products have been installed by unlicensed persons Damage caused by incorrect instal
6. al blocks ensure all wires are making proper contact If it is a Typhoon fan check and ensure the reversing switch plate under the switch cover is not bent also check the 3 wires coming from the switch plate are straight Occasionally the switch plate may get bent during transportation this allows the switch cover to press against the plate and stop the fan from working If it is a Typhoon fan check the nine pin plug under the switch cover is properly connected and the colours on the plug are corresponding If it is a Concept fan and it has an external start up capacitor check that this external capacitor is properly connected Fan speed is not corresponding to the wall controller Check the speeds on the wall controller has been wired correctly and are making proper contact Brown speed 1 Purple speed 2 Red speed 3 Check wires in the terminal block are connected properly connection wires should be stripped back at the connection point and unused wires should be sealed and capped off Check that the reversing switch is pushed into its Summer or Winter position Fan is not corresponding to the remote control Check for flat battery Make sure the dipswitch settings in the hand piece and the remote receiver for the same fan are corresponding Fan is wobbling Check the ball joint slot is locked into the hanger bracket groove Make sure blades are a matching set the letters on matching sets of blades should be identical with t
7. crews va Adjustable Arms Centre Point Ball Joint S Step 2 Fig 14 Loosen the ball joint screw take out the ball joint pin and remove the ball joint Then slide off the canopy cover Ball Joint Pin Ball Joint a NP Tighten Ball Joint Screw Step 3 Fig 15 amp 16 Now install the extension rod and reverse step 1 amp 2 to secure the rod to the fan and the ball joint NOTE If the extension rod needs to be shortened cut the rod to the required length and drill the appropriate hole size to fit the ball joint pin The cut end of the rod should be used on the ball joint end only When installing a 1 8m extension rod the wiring will need to be extended and joined This should be done using crimp style connectors 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC Electrician Installation Manual Majestic Duo Ceiling Fan INTERNATIONAL Trouble Shooting Tips Fan Fan will not start Check that the reversing switch is pushed into its Summer or Winter position Check wire connections in the wall switch and termin
8. he numbers varying within 3 grams of each other Check blade screws are tightened firmly If necessary use balancing kit provided to settle the wobble Fan is noisy Check all screws and parts are secured firmly Ensure there are no loose parts moving inside the motor housing Make sure the fan is installed with a Hunter Pacific wall controller only do not use solid state controllers as they can cause unpleasant motor noises National Warranty Line 1300 360 280 WARNING Monday to Friday from 9am to 5pm EST Only available within Australia Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of the fan If only one blade is damaged you are still required to replace with a new set 10 HUNTER PACIFIC IN T Quic Electrician Installation Manual Majestic Duo Ceiling Fan E R NATIONAL k Checklist Electricians make sure everything on this checklist is ticked off before you leave the installation site If you have trouble installing our product please refer to the trouble shooting section on the previous page first then phone the Hunter Pacific Warranty Line on 1300 360 280 open 9am to 5pm EST DO NOT uninstall the fan and DO NOT return fan to retailer 10
9. lation force majeure electrical surges lightning power grid fluctuations water or by connection to alternative power supply sources such as solar inverters etc is not eligible for warranty repair Blades must be replaced only as a complete set Blades are supplied only as a pre balanced set and the replacement of individual blades may void the warranty by causing mechanical damage to the motor excessive noise or premature wear When products are installed in a location requiring special access equipment such as scaffolding or scissor lifts etc the cost of providing installing and operating special access equipment must be borne by the site owner For safety and to protect your customers warranty the following must be taken into account when installing and operating the product s a DO NOT USE SOLID STATE WALL CONTROLLERS Neither leading nor lagging edge controllers will give satisfactory performance Wall controls must only be types approved for use by Hunter Pacific International b The fan light and bracket must be earthed c Fan and light must be run from the same final circuit d Mounting bracket must be firmly screwed to a solid structure such as a concrete ceiling steel structure or timber framing If additional bracing is added it must be firmly secured to the rafters and not left floating on the ceiling Special mounts such as T hooks are available for certain types of installation e After installatio
10. n fan blades must be at least 2 1 m 7 feet above floor level f The use of these products by children and the infirm must be under supervision IF THERE ARE ANY PROBLEMS WITH THE PRODUCT AT TIME OF INSTALLATION THE INSTALLER MUST CONTACT THE WARRANTY HOT LINE NUMBER 1300 360 280 BEFORE LEAVING THE JOB SITE PLEASE DO NOT REMOVE THE FAN FROM THE CEILING ONCE INSTALLED UNLESS INSTRUCTED TO DO SO Electrician Installation Manual Majestic Duo Ceiling Fan HUNTER PACIFIC INTERNATIONAL Parts List Majestic Duo Mounting Plate Optional OD be CE a Hex Head Screw Standard Ball Joint Down Rod _ _ Canopy Cover Motor Unit Down Rod Pin Screw a f E Nut Motor Unit Base Plate S CODE see FAN MODEL NAME COLOUR 2x 40cm 16 fan heads Majestic Duo Brushed Aluminium 3 Electrician Installation Manual Majestic Duo Ceiling Fan HUNTER PACIFIC INTERNATIONAL PARTS LIST TABLE Please refer to the parts list image on the previous and the parts list table below when installing this fan It is also a good idea to use this table to check that all the parts you require to install this fan properly is in the fan box Majestic Duo Parts List en apn Pek CanopyGover h moro 2 Ball Joint these parts come Ball Joint Screw preassembled in the box Ball Joint Pin 1 Do not attempt to operate the fan or optional light kit with any wall control that
11. nter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set Electrician Installation Manual Majestic Duo Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Assembling the fan Adjustable Arms Locating Slots Knurled Knob OF STEP 7 Fig 8 Secure the motor unit on to STEP 6 Fig 7 Take the motor unit and lock the adjustable arms using the knurled knobs the locating lug into the locating slot Washer ie q Rotato Ss Retaining Motor Unit _ Nut Base Plate o S Screw wa STEP 9 Fig 10 Tighten the retaining nut to the motor shaft at the bottom of the rotator and then place the motor unit base STEP 8 Fig 9 Fit the washer onto the motor plate on to the rotator Secure the motor shaft then put the rotator on after it Once the unit base plate by pressing it against the rotator is on tighten the screws to secure the rotator and turning it clockwise rotator in place 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do n
12. ot mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set Electrician Installation Manual Majestic Duo Ceiling Fan HUNTER PACIFIC INTERNATIONAL Installation Instructions Assembling the fan STEP 10 Fig 11 Manually adjust the adjustable arms as shown in the diagram above to the position that suits you Motor Unit STEP 11 Fig 12 Manually adjust the motor units to the angle that suits you Refer to the diagram above 1 Do not attempt to operate the fan or optional light kit with any wall control that is not approved by Hunter Pacific for use with its fans DO NOT use solid state controllers The use of unapproved controllers will void your warranty 2 Do not mix blade sets from one fan to another as this may upset the balance of WARNING the fan If only one blade is damaged you are still required to replace with a new set HUNTER PACIFIC INTERNATIONAL Electrician Installation Manual Majestic Duo Ceiling Fan Installation Instructions Attaching an extension rod Hunter Pacific rods to be used ONLY a Down Rod Pin Screw Hole a Wires 6 gt ee Screws Aa QNL Step 1 Fig 13 Loosen the down rod screws and unlock the down rod pin screw to remove the standard down rod from the adjustable arm centre point Down Rod Pin Screw Hole e a AQ Down Rod Pin S
Download Pdf Manuals
Related Search