user's Manual
Contents
1. 9 Loop belt around shaft Twist belt as shown 10 Slide the brush belt assembly back into the housing recesses so the supports seat properly into the housing The assembly is designed to fit only one way into housing NOTE The brush will rotate in the wrong direction if the belt is twisted incorrectly 11 Replace belt cover id aseplate AAA a L ro T P intr ia Lift Rollerbrush and Belt straight up to remove Proper Belt Orientation Position Belt between these two Flanges TROUBLESHOOTING THE TURBINE POWERHEAD CAUTION Moving parts disconnect from vacuum system before servicing unit Use the chart below to troubleshoot common problems you may experience with your turbine powerhead If you cannot solve the problem using the solutions below please contact your distributor or dealer for service Turbine Brush Bounces Check for clog at air intake Clean central vac power unit guard screenf filter Check for clog in hose Check for clog in tube line Ensure belt orientation is correct Change direction you are vacuuming ae I o o WARNING Please take care not to run your turbine powerhead over large objects such as socks or children s toys Obstructions which cause the roller brush to stop suddenly may snap the drive belt and invalidate your warranty2. D REMOVING CLOGS Follow these steps if the turbine becomes obstructed 1 Turn off vacuum system and disconnect the Powerhead 2 Remove the clear belt cover by turning the Powerhead over and rotating the two latches until they align with the openings in the belt cover Remove the belt cover 3 Remove debris from the intake or turbine Rotate brush to ensure the system is clear Ensure the orange seal on the belt cover and mating surfaces are clean before reinstalling the belt cover 4 To reinstall the belt cover simply insert the front of the belt cover under the baseplate edge and lower into its original position 5 Secure the belt cover in place by turning the two latches to the locked position Turn latches to remove Belt Cover qa Remove Belt Cover _ Like This Baseplate Edge Use amp Care of Your Turbine Powerhead E REPLACING THE DRIVE BELT It is recommended that the drive belt be replaced by a Qualified Service Technician 1 Turn off vacuum system and disconnect powerhead 2 Remove belt cover as described on page 4 3 Remove the 3 screws securing the baseplate 4 Remove the baseplate 5 IMPORTANT Please note correct brush and belt orientation They must be reinstalled correctly for proper function 6 Lift the brush belt and support assembly out of the housing 7 Remove the old belt 8 Place the new belt over one end onto the brush roller between the two center flanges
3. TURBO BRUSH EX Part No VAC 039 OCentral Intelligent Central Systems A DIVISION OF MESA CORPORATION THE HOME OF VALET www valet com au SALES SERVIGE SPARES 1800 050 333 NESS HEAD OFFICE 02 8825 9222 VAC 039 Turbo Brush EX User s manual This Turbine Powerhead has been engineered for higher performance quieter operation and superior cleaning ability lt has been carefully designed and manufactured for long life reliable performance and convenient cleaning It requires no electricity because it runs off the airflow of your central vacuum system The Turbine Powerhead moves easily and does not require downward pressure for thorough cleaning Please read and save these Operating Instructions SAFETY PRECAUTIONS As with any tool with moving parts caution must be exercised while using this Turbine Powerhead 1 Keep hair hands and feet away from rotating brush while the Turbine Powerhead is running 2 Remember that Turbine Powerheads operate whenever they are connected to a running vacuum If children are present make sure to turn vacuum system off when leaving Powerhead unit unattended 3 Do not attempt to service or unclog Turbine Powerhead while unit is running Use amp Care of Your Turbine Powerhead A ATTACHING THE TURBINE POWERHEAD To attach your metal wand simply insert wand into Powerhead neck until it fits snugly The built in locking mechanism will prevent the wand from coming l
4. oose To detach wand depress wand release tab on back of neck with foot or hand and twist wand free Inserting the Wand Push here to Release Wand The wand can be locked in an upright position by pushing it forward until the lock is engaged This locked position is convenient for storage and lifting the Powerhead To release wand from the vertical locked position gently place foot on Powerhead grasp wand and pull back u jr a ra T o st if E k u li _ Use amp Care of Your Turbine Powerhead B OPERATING PROCEDURES Your Turbine Powerhead runs off the airflow of your vacuum system lt has no on off switch Whenever it is attached to an operating vacuum system it will be running No adjustments to the powerhead are necessary for different types of carpeting To ensure maximum efficiency of the Turbine Powerhead make sure that any filters bags and cleaning hoses in your vacuum system are clean and free of blockage Avoid picking up water or spilled liquid with your Turbine Powerhead The vacuum system is designed for dry pick up only C CLEANING ROLLER BRUSH Turn off vacuum system and disconnect Powerhead Threads string carpet fiber fuzz and similar items may become wound around the beater brush These should be removed by unwinding them by hand or carefully cutting with scissors Keeping the beater brush clean will maintain efficiency Use amp Care of Your Turbine Powerhead
Download Pdf Manuals
Related Search