MS1690 Focus® Area Imaging Bar Code Scanner - i
Contents
1. Figure 1 Scanner Components Item Description Yellow LED See Visual Indicators on page 17 White LED See Visual Indicators on page 17 Blue LED See Visual Indicators on page 17 Speaker See Audible Indicators on page 16 Trigger Red Window LED Aperture Cable Release See The PowerLink Cable on page 5 10 pin RJ45 Female Socket AAA ene e See Scanner Pinout Connections on page 34 INTRODUCTION The PowerLink Cable Connecting i Important If the PowerLink cable is not fully latched the unit can power intermittently Insert Insert the cable There Pull gently to insure will be an audible click the cable is locked Figure 2 Figure 3 Disconnecting Before removing the cable from the scanner Metrologic recommends that the power on the host system is off and the power supply has been disconnected from the PowerLink cable Figure 4 Releasing the PowerLink Cable 1 Locate the small pin hole on the handle of the unit near the cable 2 Bend an ordinary paperclip into the shape shown above 3 Insert the paperclip or other small metallic pin into the small pin hole 4 There will be a faint click when the lock is released Pull gently on the strain relief of the PowerLink cable to remove the cable from the unit INTRODUCTION Labels Each scanner has a label l2. Check that the scanner and the host are configured for the same interface parameters 23 TROUBLESHOOTING GUIDE The unit is transmitting each character twice Alpha characters show as lower case Everything works except for a couple of characters The unit powers up OK and scans OK but does not communicate properly with the host Characters are being dropped 24 The configuration is not set correctly The computer is in Caps Lock mode These characters may not be supported by that country s key look up table The com port at the host is not working or not configured properly The cable is not connected to the correct com port Inter character delay needs to be added to the transmitted output Increase interscan code delay setting Adjust whether the FO break is transmitted It may be necessary to try this in both settings Enable Caps Lock detect setting of the scanner to detect if the PC is operating in Caps Lock Try operating the scanner in Alt Check to make sure that the baud rate and parity of the scanner and the communication port match and the program is looking for RS232 data Check to make sure that the cable is connected to the correct com port Add some inter character delay to the transmitted output by using the Configuration Guides MLPN 00 02544 and 00 02065 DESIGN SPECIFICATIONS MS1690 DESIGN SPECIFICATIONS OPERATIONAL Light Sourc
3. Inter character delay configurable in 1 msec steps maximum of 255 msecs Number of scan buffers maximum Transmit UPC A check digit Convert UPC A to EAN 13 29 DEFAULT SETTINGS COMMUNICATION PARAMETERS PARAMETER DEFAULT RS232 IBM 46XX SE Transmit lead zero on UPC E Transmit Codabar Start Stop Characters CLSI Editing Enable Transmit Mod 43 Check digit on Code 39 Transmit Mod 10 ITF Transmit MSI Plessy 8 Data Bits 7 Data Bits Stop Bits Transmit Sanyo ID Characters Nixdorf ID UPC Suffix Carriage Return Line Feed Disabled by default in KBW Tab Prefix Tab Suffix Character RTS CTS Message RTS CTS 30 DEFAULT SETTINGS COMMUNICATION PARAMETERS PARAMETER DEFAULT RS232 IBM 46XX XON XOFF Handshaking ACK NAK Five Digit Supplements Bookland 977 2 digit Supplemental Requirement Supplements are not Required Two Digit Redundancy Five digit Redundancy T Code Selects with configurable Code Length Locks Configurable Prefix characters 10 avail Suffix characters o 10 avail Prefixes for Individual Code types Editing Function Control Key Support Linear 1D Omni 2D T These options are mutually exclusive One can not be used in conjunction with the other 31 CONFIGURATION MODES The MS1690 Focus Series has three modes of configuration 32 Bar Codes The MS1690 can be configured by scanning the bar codes included in the Met
4. Metrologic We really work for you METROLOGIC INSTRUMENTS INC MS1690 Focus Area Imaging Bar Code Scanner Installation and User s Guide Copyright 2007 by Metrologic Instruments Inc All rights reserved No part of this work may be reproduced transmitted or stored in any form or by any means without prior written consent except by reviewer who may quote brief passages in a review or provided for in the Copyright Act of 1976 Trademarks Metrologic is a registered trademark of Metrologic Instruments Inc Products identified in this document are hereby acknowledged as trademarks registered or otherwise of Metrologic Instruments Inc or their respective companies TABLE OF CONTENTS o ROTE 1 scanner and ACcessSorles ccocoooonnnccnereconnnanenrncann onerosa 2 Scanner COMponen is be nl lu a lt e 4 The PowerLink Gables rhe Eie ais 5 Bet 6 E Hate ln er 6 Installing the Scanner to the Host System RSZ3Z MS 16902 E EN 7 Keyboard Wedge MS1690 47 ccccccssssseeeecceeseeeecesneseeecesssuseeeeeesnaesseeeeees 8 Stand Alone Keyboard MSTIGOU A 9 IBMIMSTOIO Ti AAA 10 Full Speed USB MS1690 40 nteorated 11 Low Speed USB MS1690 38 ntegorated 11 Stand Kits Stand Components MLPN AG O014 n 12 HardMounting the Stadt diia 13 Assembling the Stand MEET 14 Scanner Operation Two Default Modes of Operation n0nnnusennunannnnsannensnnnrsrrireenrrernnrrnsnnrrnens 15 AudibleIndiCatOts we c
5. Operating 0 C to 40 32 to 104 F Temperature Storage 40 C to 60 C 40 F to 140 F Humidity 0 to 95 Relative Humidity Non Condensing Light Levels Up to 100 000 Lux 9 290 Footcandles Designed to withstand 1 5 m 5 ft drops Sealed to resist airborne particulate contaminants Specifications are subject to change without notice 26 APPLICATIONS AND PROTOCOLS The model number on each scanner includes the scanner number and factory default communications protocol VERSION SCANNER COMMUNICATION PROTOCOL S IDENTIFIER IBM 468X 469X RS232 TXD RXD RTS CTS RS232 TX RX RTS CTS DTR MS1690 Keyboard Wedge Stand Alone Keyboard and RS232 Transmit Receive The MS1690 47 with a built in PC Keyboard Wedge Interface is designed for Keyboard emulation use only Many RS232 configurable functions available in other Metrologic scanners are also available as keyboard wedge functions The following are the most important selectable options specific to the keyboard wedge Keyboard Type e AT includes IBM PS2 models 50 55 60 80 e IBM PS2 includes models 30 70 8556 Keyboard Country Type e USA e German e Spanish e Belgium e Italian e Swiss e French e Japanese e United Kingdom For additional information on the MS 1690 s default settings refer to pages 28 31 For information on how to change the default settings refer to help files in MetroSet2 or the MetoSelect Single Line
6. PowerLink Cable 53 53000 3 Coiled Shield Ground Stand Alone Keyboard PowerLink Cable 53 53020 3 PC Data USB Power Communication Cable 53 53213 N 3 53 53214 N 3 or 53 53235 N 3 PC 5V V_USB USB Type A Locking with Power Shield Shield 36 USB Non Locking SCANNER AND CABLE TERMINATIONS Cable Connector Configurations Host End Keyboard Wedge PowerLink Cable 53 53002 3 Coiled i Keyboard Clock 6 Pin DIN Male No Connect Metrologic will supply an adapter cable with a 5 pin DIN male connector on one end and a 6 pin mini DIN female connector on the other According to the termination required connect the appropriate end of the adapter cable to the PowerLink cable leaving the necessary termination exposed for connecting to the keyboard and the keyboard port on the PC 6 pin Mini DIN Female 2 No Connect 37 LIMITED WARRANTY The MS1690 Focus scanners are manufactured by Metrologic at its Blackwood New Jersey U S A facility The MS1690 Focus scanners have a five 5 year limited warranty from the date of manufacture Metrologic warrants and represents that all MS1690 Focus scanners are free of all defects in material workmanship and design and have been produced and l
7. units can be upgraded To upgrade all units a power supply and PowerLink cable MLPN 54 54014 are required RS232 units can be upgraded using the standard PowerLink cable MLPN 53 53xxx 3 The program guides the user with its simplistic one click approach The user must first select the file Once the file is selected and verified the scanner is ready to be upgraded Press the Flash Scanner button to upgrade the scanner The unit will go into a flash mode the blue and white LEDs will be flashing alternately The user can follow the progress of the upgrade by watching the screen for details When the upgrade is complete the scanner will reset itself If a razz beep occurs the scanner did not upgrade properly Contact a Metrologic service representative for additional assistance 33 SCANNER AND CABLE TERMINATIONS Scanner Pinout Connections MS1690 14 RS232 The MS1690 scanner interfaces terminate to a 10 pin RJ45 Female Socket The serial label indicates the interface enabled when the scanner is shipped from the factory MS1690 47 Keyboard Wedge amp Stand Alone Keyboard Figure 18 Shield Ground Oo 34 SCANNER AND CABLE TERMINATIONS Scanner Pinout Connections MS1690 38 Low Speed USB Ground Oo esch Figure 19 Shield Ground Oo 35 SCANNER AND CABLE TERMINATIONS Cable Connector Configurations Host End Standard
8. 1D RSS PDF417 microPDF Composite Matrix and Postal Codes symbology types Firmware updates are easily loaded via Flash ROM Focus provides an extended depth of field and a built in object detection sensor IR that instantly turns on the scanner when an object is presented within the scanner s field of view Automatic in stand detection switches the scanner to a presentation mode for convenient in stand scanning Focus incorporates Metrologic s patented CodeGate technology for accurate menu style scanning and on command data transmission Interface MS1690 11 IBM 468X 469X RS232 TXD RXD RTS CTS MS1690 14 RS232 TX RX RTS CTS DTR MS1690 38 Low Speed USB MS1690 40 Full Speed USB Keyboard Wedge Stand Alone Keyboard and MS1690 47 R8232 Transmit Receive INTRODUCTION Scanner and Accessories Basic KIT MS1690 Focus Area Imaging Bar Code Scanner Kee CEET EE EE DE IET I DD E TET EES ee T TIENDE Ted 00 02065 00 02281 MS1690 Focus Area Imaging Bar Code Scanner Installation and User s Guide 00 02098 Available on the Metrologic website www metrologic com OPTIONAL ACCESSORIES AC to DC Power Transformer Regulated 5 2VDC 1 A output mA e RS232 PowerLink Cable with Built in Power Jack E 2 7 m 9 ft coiled cord long strain relief bl
9. Safety ITE Equipment IEC 60950 1 EN 60950 1 LED Class 1 LED Product IEC 60825 1 1993 A1 A2 EN 60825 1 1994 A1 A2 CLASS 1 LED PRODUCT APPAREIL A LED DE CLASSE 1 LED KLASSE 1 PRODUKT LED CLASE 1 PRODUCTO A Caution Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Under no circumstances should the customer attempt to service the LED scanner Never attempt to look at the LED beam even if the scanner appears to be nonfunctional Never open the scanner in an attempt to look into the device Doing so could result in hazardous radiation exposure The use of optical instruments with the LED equipment will increase eye hazard ZA Atenci n La modificaci n de los procedimientos o la utilizaci n de controles o ajustes distintos de los especificados aqu pueden provocar una exposici n de luz brillante peligrosa Bajo ninguna circunstancia el usuario deber realizar el mantenimiento del LED Diodo Emisor de Luz del lector Ni intentar mirar al haz del LED incluso cuando este no est operativo Tampoco deber abrir el lector para examinar el aparato El hacerlo puede conllevar una exposici n peligrosa a la luz del LED El uso de instrumentos pticos con el equipo LED puede incrementar el riesgo para la vista A Attention L emploi de commandes r glages ou proc d s autres que ceux d crits ici peut entra ner de graves irradiations Le client n
10. UE ERR Se eS 3 PowerLink 2 5 7 11 21 24 33 36 37 EE 7 36 37 Stand Alone Keyboard 9 36 37 USB EE 11 36 37 e O E 39 CC OTIO DEus asc c ctos 7 11 39 40 o putos edit nn E tU 6 7 11 A eege 39 CodeGate 1 4 15 Communication Parameters 28 31 compliance 39 40 41 Compliance 7 11 38 39 40 Configuration 2 21 24 27 32 33 Connector Pinouts 34 35 CONVE neta ve a 11 CUT Era dolida 26 Customer Service 2 3 38 D Bia Ww E 2 26 34 35 36 37 Decoder dd dde 25 Default Parameters 27 28 31 Bild dic dis 28 31 Keyboard Wedge 28 31 AAA A 28 31 Stand Alone Keyboard 28 31 LE ete naa 28 31 Depth of Field 19 E JA 26 40 41 A E 40 41 EMISSIO EE 40 41 F Firmware eee 33 Flash RON netto ets 33 H A a 5 7 11 l Illy oir 40 41 Indicator Audible 4 17 18 25 33 e MIT 4 17 18 Visual 4 17 18 25 33 Interface ee ees 21 24 25 Cable ur 7 11 36 37 IBM 1 3 10 27 28 31 34 35 Keyboard Wedge 1 2 8 27 28 31 34 35 RS232 1 2 7 27 28 31 34 35 Stand Alone Keyboard 1 2 9 27 28 31 34 35 USB 1 3 11 27 28 31 34 35 JEE 1 15 20 K Keyboard Country Type 27 Keyboard Tvpe 27 Keyboard Wedge 2 43 L Re EE 6 LED WEE
11. info jp metrologic com Metrologic Thailand Tel 661 814 2352 Email tawan jandang th metrologic com MTLG Auto ID Instruments Shanghai Co Ltd Tel 86 21 58692780 Fax 86 21 58692782 Email info cn metrologic com Suzhou Sales Office Tel 86 512 67622550 Fax 86 512 67622560 Email info cn metrologic com Taiwan Sales Office Tel 886 2 2351 0125 Email john cheng tw metrologic com NOTES January 2007 Printed in the USA 0 2098D 00
12. 1 48 63 24 94 Email info fr metrologic com Metrologic Eria Iberica SL Tel 34 913 272 400 Fax 34 913 273 829 Email info es metrologic com Metrologic Russia Tel 7 095 730 7424 Fax 7 095 730 7425 Email info ru metrologic com Metrologic Instruments GmbH Tel 49 89 89019 0 Fax 49 89 89019 200 Email info europe metrologic com Metrologic Instruments Italia Tel 39 0 57 6511978 or 39 051 651 1978 Fax 39 0 51 6521337 Email info it metrologic com Metrologic Instruments Poland Tel 48 22 545 04 30 Fax 48 22 545 04 31 Email info pl metrologic com Metrologic Instruments UK Limited Tel 44 0 1256 365900 Fax 44 0 1256 365955 Email info uk metrologic com Metrologic APAC Headquarters Tel 65 6842 7155 Fax 65 6842 7166 Email info sg metrologic com Beijing Sales Office Tel Fax 86 10 82253472 Email info cn metrologic com Chengdu Sales Office Tel Fax 86 28 86200109 Email info cn metrologic com Guangzhou Sales Office Tel 86 20 38823476 Fax 86 20 38823477 Email info cn metrologic com India Sales Office Tel 91 80 51256718 Fax 91 80 51256719 Email info in metrologic com Korea Sales Office Tel 82 2 6205 5379 Fax 82 2 3444 3980 Email Scott lee kr metrologic com Metrologic Asia Pte Ltd Tel 65 6842 7155 Fax 65 6842 7166 Email info sg metrologic com Metrologic Japan Co Ltd Tel 81 3 3839 8511 Fax 81 3 3839 8519 Email
13. 7 18 33 Vie le TE 26 W Warranty ET 38 White LED 4 7 11 17 18 33 Window mH 4 6 Y Yellow LED 4 7 11 17 18 CONTACT INFORMATION AND OFFICE LOCATIONS Worldwide Headquarters Metrologic Instruments Inc 90 Coles Road Blackwood NJ 08012 4683 Email info metrologic com Tel 856 228 8100 Customer Service 1 800 ID METRO Fax 856 228 6673 Sales Fax 856 228 1879 Marketing Fax 856 228 0653 Legal Finance Metrologic Companies Adaptive Optics Associates AOA Tel 617 806 1400 Fax 617 806 1899 Email info aoainc com Omniplanar Tel 856 537 6100 Fax 856 537 6116 Email info omniplanar com Metrologic The Americas Headquarters Tel 1 856 537 6400 Fax 1 856 537 6474 Email info us metrologic com Metrologic Canada Tel 416 752 7190 Fax 416 752 8060 Email info ca metrologic com Metrologic do Brasil Ltda Tel 55 11 5182 7273 Fax 55 11 5182 7198 Email info sa metrologic com Metrologic Mexico S A DE C V Tel 55 5365 6247 Fax 55 5362 2544 Email info mx metrologic com Metrologic South America Tel 239 642 1958 Fax 239 642 1959 Email info sa metrologic com Metrologic USA Tel 1 856 537 6400 Fax 1 856 537 6474 Email info us metrologic com Metrologic EMEA Headquarters Tel 49 89 89019 0 Fax 49 89 89019 200 Email info europe metrologic com Metrologic Eria France SA Tel 33 0 1 48 63 78 78 Fax 33 0
14. Configuration Guide MLPN 00 02544 27 DEFAULT SETTINGS COMMUNICATION PARAMETERS Many functions of the scanner can be configured that is enabled or disabled The scanner is shipped from the factory configured to a set of default conditions The default parameter of the scanner has an asterisk in the charts on the following pages If an asterisk is not in the default column then the default setting is OFF or DISABLED Every interface does not support every parameter If the interface supports a parameter listed in the charts on the following pages a check mark v will appear PARAMETER DEFAULT RS232 IBM 46XX AE Multi Try Trigger Out of Stand Presentation Mode In Stand Continuous Trigger Single Trigger Aiming in Trigger and Continuous Modes Aiming in Presentation Mode Long Range In Stand Short Range In Stand Long Range Out of Stand Short Range Out of Stand UPC EAN Code 128 Code 93 Codabar Interleaved 2 of 5 ITF MOD 10 check on ITF Code 11 Code 39 Full ASCII Code 39 Data Matrix QR Code 28 DEFAULT SETTINGS COMMUNICATION PARAMETERS PARAMETER DEFAULT RS232 IBM 46XX Maxicode Mod 43 Check on Code 39 MSI Plessy 10 10 Check Digit Beeper tone Normal Before Beep transmit sequence transmit Three beeps on timeout Same symbol rescan timeout 1000 msecs Same symbol rescan timeout configurable in 50 msec steps maximum of 6 35 sec No Same symbol timeout
15. F ALL OTHER WARRANTIES OR GUARANTEES EITHER EXPRESS OR IMPLIED AND SPECIFICALLY EXCLUDES WITHOUT LIMITATION WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE UNDER THE UNIFORM COMMERCIAL CODE OR ARISING OUT OF CUSTOM OR CONDUCT THE RIGHTS AND REMEDIES PROVIDED HEREIN ARE EXCLUSIVE AND IN LIEU OF ANY OTHER RIGHTS OR REMEDIES IN NO EVENT SHALL METROLOGIC BE LIABLE FOR ANY INDIRECT OR CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES DAMAGES TO PERSON OR PROPERTY OR EFFECT ON BUSINESS OR PROPERTY OR OTHER DAMAGES OR EXPENSES DUE DIRECTLY OR INDIRECTLY TO THE PRODUCT EXCEPT AS STATED IN THIS WARRANTY IN NO EVENT SHALL ANY LIABILITY OF METROLOGIC EXCEED THE ACTUAL AMOUNT PAID TO METROLOGIC FOR THE PRODUCT METROLOGIC RESERVES THE RIGHT TO MAKE ANY CHANGES TO THE PRODUCT DESCRIBED HEREIN CORPORATE HEADQUARTERS METROLOGIC EUROPEAN REPAIR CENTER NORTH AMERICA MERC Metrologic Instruments Inc Metrologic Eria Ib rica SL 90 Coles Rd C Alfonso Gomez 38 40 1D Blackwood NJ 08012 4683 28037 Madrid Customer Service Department Tel 34 913 751 249 Tel 1 800 ID METRO Fax 34 913 270 437 Fax 856 228 6673 Email info metrologic com MTLG Auro ID INSTRUMENTS SHANGHAI CO LTD Suzhou Sales Office BLK A Room 03 03 04 No 5 Xinghan Street Xinsu Industrial Square China Singapore Suahou Industrial Park Suzhou PRC Tel 86 512 67622550 Fax 86 512 67622560 Email info cn metrologic com 38 REGULATORY COMPLIANCE
16. N 7 11 21 24 25 39 40 PUG ict sc lee ads 7 11 17 18 White 1 11 17 18 Y ellOW ens 7 11 17 18 Light Levels 26 Light Source 25 M Maintenance serere 6 Meteor i dco pia eur ux dede ula a 33 MetroSelect 16 27 32 MeitrozGet 33 Mode of Operation 15 N Mee NETT 39 P A AA 42 PDF PE 19 Pinouts 34 35 36 37 POWER meedia atenda eia ds 7 11 26 33 Power Supply 5 7 11 ower mk 4 Presentation 15 Product Safety 39 40 Protocols dunt etr it in rie paga das 27 R Raz ds 17 18 21 24 AT cide EE 38 RMA eter a eo E 38 PRO 22 EE 2 S E A A 39 SEL Vane eee 7 11 44 SOL VIGO td did dsd 38 Specifications Eleccion 26 Environmental 26 Mechanical 25 Operational 25 JE 3 12 14 15 Stand Alone Keyboard 2 Swiftdecoder unnn 1 T AA a n 17 18 A donis ndr ch 16 Transformer 2 7 11 26 A O e 4 Troubleshooting 21 24 U A AT EES 6 7 11 Upgrade ET 33 USB Full Speed 1 3 11 27 28 31 35 36 Low Speed 1 3 11 27 28 31 35 36 V Ventilation 26 Visual Indicator 1
17. R siet Area 102 mm 4 00 Long IR Activation Area 203 mm 8 00 Figure 17 IR Activation Area Specifications are subject to change without notice 20 TROUBLESHOOTING GUIDE The following guide is for reference purposes only Contact a Metrologic representative at 1 800 ID Metro or 1 800 436 3876 to preserve the limited warranty terms All Interfaces MS1690 Series Troubleshooting Guide No LEDs beep or illumination Long Razz tone on power up Long Razz tone when exiting configuration mode Long Razz tone Short Razz tone in configuration mode No power is being supplied to the scanner No power is being supplied to the scanner from the host The wrong communication cable has been used There has been a scanner configuration failure There has been a RAM or ROM failure There was a failure to save the new configuration There is a scanning mechanism failure An invalid bar code has been scanned Check transformer outlet and power strip Make sure the cable is plugged into the scanner Some host systems cannot supply enough current to power Focus A power supply may be required Check that the communication cable matches the unit type and scanner configuration Contact a Metrologic service representative if the unit will not hold the saved configuration Contact a Metrologic service representative if the unit will not function Re try to configure the scann
18. abeled in compliance with all applicable U S Federal state and local laws regulations and ordinances pertaining to their production and labeling This warranty is limited to repair replacement of product or refund of product price at the sole discretion of Metrologic Faulty equipment must be returned to one of the following Metrologic repair facilities Blackwood New Jersey USA Madrid Spain or Suzhou China To do this contact the appropriate Metrologic Customer Service Repair Department to obtain a Returned Material Authorization RMA number In the event that it is determined the equipment failure is covered under this warranty Metrologic shall at its sole option repair the Product or replace the Product with a functionally equivalent unit and return such repaired or replaced Product without charge for service or return freight whether distributor dealer reseller or retail consumer or refund an amount equal to the original purchase price This limited warranty does not extend to any Product which in the sole judgment of Metrologic has been subjected to abuse misuse neglect improper installation or accident nor any damage due to use or misuse produced from integration of the Product into any mechanical electrical or computer system The warranty is void if the case of Product is opened by anyone other than Metrologic s repair department or authorized repair centers THIS LIMITED WARRANTY EXCEPT AS TO TITLE IS IN LIEU O
19. ack Keyboard Wedge PowerLink Cable with Adapter Cable 2 7 m 9 ft coiled cord long strain relief black e Stand Alone Keyboard PowerLink Cable oars 2 7 m 9 ft coiled cord long strain relief black Other items may be ordered for the specific protocol being used To order additional items contact the dealer distributor or call Metrologic s Customer Service Department at 1 800 ID METRO or 1 800 436 3876 2 INTRODUCTION Scanner and Accessories OPTIONAL ACCESSORIES _ USB Full Speed Cable Locking Plus Power Type A Ss 2 7 m 9 ft coiled cord long strain relief black USB Full Speed Cable Locking Plus Power Type A 4 5 m 15 ft coiled cord long strain relief black 53 53214x N 3 This cable is for use with full speed USB 40 interface only USB Low Speed Communication Cable Type A i 2 7 m 9 ft coiled cord long strain relief black IBM Applications MVC 2MPC IB9 Metrologic Voltage Converter MVC Cable 12VDC to 5 2VDC Contact a Metrologic customer service representative for additional information on the MVC cable series and the host connections available 46 00147 Modular Presentation Stand Other items may be ordered for the specific protocol being used To order additional items contact the dealer distributor or call Metrologic s Customer Service Department at 1 800 ID METRO or 1 800 436 3876 INTRODUCTION Scanner Components
20. ada pia Hn det uut uei duni da ba sy cae n edet emote 16 Visual lee e e 17 Fale MOdes EE 18 Depth of Field by Minimum Bar Code Element Width 19 IS Activation Range sara A A a 20 Tro bleshooting Guide EE 21 Design Specifications PTT ana 25 Applications and ProIgeols seni diae ste do rod echa ba 27 Default Settings Communication Parameters nsnsnnsessnreeeereeerrtrennnnesrrnen 28 Configuration MOS s taxe auda oia taeda queste tud anao a ela ts da 32 TABLE OF CONTENTS Upgrading the Flash ROM Firmware occcccccononnnocncoconcnncnnonnnnnnnnancncnnnnnnnnnnnnnnnnnnnas 33 Scanner and Cable Terminations Scanner PIQUE COMMECHONS iaa 34 Cable Connector Configurations cccccoconnccnncccnnococcnncconancnnnonononanccnncnonnnannnnos 36 ten De Wataru aaa ti REO 38 Regulatory Compliance Eed 39 le 40 Class Ac DEW cti AA AA 40 NR 41 SE 42 A EE 43 Contact Information and Office Locations 45 INTRODUCTION The MS1690 Focus is a high performance hand held area imaging bar code scanner that utilizes high resolution CMOS imaging sensors for superior image quality Focus utilized Omniplanar Inc s SwiftDecoder software for reliable decoding of both 1D and 2D bar code symbologies Sharp images can be captured and transmitted in a variety of outputs including jpg bmp and tiff Omnidirectional scanning capabilities and an extended depth of field provides aggressive scanning of all standard
21. cted e Consult the dealer or an experienced radio TV technician for help Notice This Class B digital apparatus complies with Canadian ICES 003 Remarque Cet appareil num rique de classe B est conforme a la norme canadienne NMB 003 41 PATENTS This METROLOGIC product may be covered by but not limited to one or more of the following U S Patents U S Patent No 7 086 595 7 128 266 No license right or sublicense is granted either expressly or by implication estoppel or otherwise under any METROLOGIC or third party intellectual property rights whether or not such third party rights are licensed to METROLOGIC including any third party patent listed above except for an implied license only for the normal intended use of the specific equipment circuits and devices represented by or contained in the METROLOGIC products that are physically transferred to the user and only to the extent of METROLOGIC S license rights and subject to any conditions covenants and restrictions therein Other worldwide patents pending 42 A O IA 2 7 11 26 Accessories eene 2 Ada osito iar ess cia qiia 2 37 ADF eege ee 4 Audible Indicator 17 18 33 B Bar Code 21 24 25 32 Bar Code Element 19 Beep 17 18 21 24 25 33 Blue LED 4 7 11 17 18 33 C able suc do ote sede iind 3 NES IN MICHI NENNT ann 10 Keyboard Wedge 8 36 37 PIG
22. dicates the scanner is in configuration mode A short razzberry tone indicates that an invalid bar code has been scanned while in this mode Flashing Blue The blue LED will flash if the trigger is pressed while the scanner is in the in stand presentation mode The blue LED will stop flashing after a brief period of time SCANNER OPERATION Failure Modes Long Razzberry Tone During Power Up Failed to initialize or configure the scanner If the scanner does not respond after reprogramming return the scanner for repair Short Razzberry Tone During Scanning An Invalid bar code has been scanned when in configuration mode or the trigger has been pulled too fast 18 SCANNER OPERATION Depth of Field by Minimum Bar Code Element Width 31 mm 1 2 Width at Face 0 mm 0 19 mm 0 75 32 mm 1 25 51 mm 2 00 108 mm 4 25 184 mm 7 25 216 mm 8 50 222 mm 8 75 Figure 16 Depth of Field by Minimum Bar Code Element Width Specifications are subject to change without notice SCANNER OPERATION IR Activation Range The MS1690 has a built in object detection sensor that instantly turns on the scanner when an object is presented within the scanner s IR activation Area 127 mm 50 Width At Window 19 mm 75 IR Activation Area 102 mm 4 00 Long IR Activation Area 203 mm 8 00 6 4 mm 25 Width At 1 0 from Window I
23. e LED 645 nm Maximum Output of an Osram LED Maximum 85 mA emits 3 120 mlm 0 mm 254 mm 0 10 for 0 330 mm 13 mil Bar Code at Default Setting 49 mm W x 19 mm H 1 9 W x 0 8 H at 20 mm 0 8 264 mm x 106 mm 10 4 W x 4 2 H at 280 mm 11 07 Minimum Bar Width 0 127 mm 5 0 mil Long Range 0 mm 203 mm 0 8 from Window Depth of Scan Field Field of View Infrared Activation Short Range 0 mm 101 mm 0 4 from Window Autodiscriminates All Standard 1 D RSS PDF417 44 microPDF MaxiCode Data Matrix QR Code UCC EAN Decode Capability Composites Postals Aztec Image Transfer BMP TIFF or JPEG output System Interfaces PC Keyboard Wedge RS232 IBM 468X 469X Stand y Alone Keyboard USB Low Speed and Full Speed Print Contrast 20 Minimum Reflectance Difference Up to 80 Data Characters on 1D bumper Characters Read 1850 Text Characters for PDF417 Beeper Operation 7 tones or no beep Unit Powered Ready to Scan Indicators LED Default Settings White Good Read Read MECHANICAL A 79 mm 3 1 Standard 2 7 m 9 Coiled Optional 2 1 m 7 Straight Specifications are subject to change without notice 25 DESIGN SPECIFICATIONS MS1690 DESIGN SPECIFICATIONS ELECTRICAL Input Voltage 5 0VDC 0 25V DC Transformer Class 2 5 2VDC 1A For Regulatory Compliance information see pages 39 41 ENVIRONMENTAL
24. e doit en aucun cas essayer d entretenir lui m me le scanner ou la LED Ne regardez jamais directement le rayon LED m me si vous croyez que le scanner est inactif N ouvrez jamais le scanner pour regarder dans l appareil Ce faisant vous vous exposez un risque d irradiation L emploi d appareils optiques avec cet quipement LED augmente le risque d endommagement de la vision Achtung Die Verwendung anderer als der hier beschriebenen Steuerungen Einstellungen oder Verfahren kann eine gefahrliche Licht emittierender Dioden strahlung hervorrufen Der Kunde sollte unter keinen Umstanden versuchen den Licht emittierender Dioden Scanner selbst zu warten Sehen Sie niemals in den Licht emittierender Diodenstrahl selbst wenn Sie glauben da der Scanner nicht aktiv ist ffnen Sie niemals den Scanner um in das Ger t hineinzusehen Wenn Sie dies tun k nnen Sie sich einer gef hrlichen Licht emittierender Diodenstrahlung aussetzen Der Einsatz optischer Ger te mit dieser Laserausr stung erh ht das Risiko einer Sehsch digung AM Attenzione L utilizzo di sistemi di controllo di regolazioni o di procedimenti diversi da quelli descritti nel presente Manuale pu provocare delle rischiose esposizioni radiattive Il cliente non deve assolutamente tentare di riparare egli stesso lo scanner LED o diodo emettitore di luce Non guardate mai il raggio LED d emettitore di luce anche se credete che lo scanner non sia attivo Non aprite mai
25. ed MS1690 38 1 Turn off the host device 2 Plug the male 10 pin RJ45 end of the USB cable into the 10 pin socket on the Focus You will hear a click when the connection is made 3 Plug the USB type A end of the USB cable into the host s USB port 4 Turn on the host device 5 Focus will start to initialize All LEDs yellow white and blue will light for approximately 2 seconds then start to alternately flash When the scanner has finished initializing the LEDs will stop flashing and the unit will beep 3 times indicating that the scanner is Figure 10 ready for use ER As a default the MS1690 38 leaves the factory with USB Keyboard id Emulation Mode enabled For information on configuring the MS1690 38 for USB Serial Emulation Mode please refer to the USB section of the MetroSelect Single Line Configuration Guide MLPN 00 02544 i Plugging the scanner into a port on the host device does not guarantee that scanned information will be communicated properly to the host device The scanner is shipped from the factory configured with default settings Please refer to the MetroSelect Single Line Configuration Guide MLPN 00 02544 or MetroSet2 s help files for instructions on changing the scanner s configuration In addition please check that the scanner and host system are using the same communication protocol A See power source caution statement located on page 6 of this manual STAND KITS Stand Comp
26. er Contact a Metrologic Service Representative if the unit will not hold the saved configuration Contact a Metrologic service representative Scan a valid bar code or quit configuration mode 21 TROUBLESHOOTING GUIDE The unit powers up but does not beep when bar code is scanned The beeper is disabled and no tone is selected The unit powers The bar code up but does not symbology trying to scan and or be scanned is not beep enabled The unit powers The scanner is trying up but does not to scan a barcode that scan and or does not match the beep configured criteria The unit scans a bar code but locks up after the first scan and the white LED stays on The scanner is configured to support some form of host handshaking but is not receiving the signal The unit scans but the data transmitted to the host is incorrect The scanner s data format does not match the host system requirements 22 Enable the beeper and select a tone UPC EAN Code 39 interleaved 2 of 5 Code 93 Code 128 Codabar and PDF are enabled by default Verify that the type of bar code being read has been selected Verify that the bar code being scanned falls into the configured criteria i e character length lock or minimum bar code length settings If the scanner is setup to support ACK NAK RTS CTS or XON XOFF verify that the host cable and host are supporting the handshaking properly V
27. erify that the scanner s data format matches that required by the host Make sure that the scanner is connected to the proper host port TROUBLESHOOTING GUIDE The unit beeps at some bar codes and NOT for others of the same bar code symbology The unit scans the bar code but there is no data The unit scans but the data is not correct The print quality of the bar code is suspect The aspect ratio of the bar code is out of tolerance The bar code may have been printed incorrectly The scanner is not configured correctly for this type of bar code The minimum symbol length setting does not work with the bar code The configuration is not set correctly The configuration is not set correctly The scanner and host may not be configured for the same interface parameters Check print mode The type of printer could be the problem Change print settings i e change to econo mode or high speed Check print mode The type of printer could be the problem Change print settings i e change to econo mode or high speed Check if it is a check digit character or border problem Check if check digits are set properly Check if the correct minimum symbol length is set Make sure the scanner is configured for the appropriate mode Make sure that the proper PC type AT or PS2 is selected Verify correct country code and data formatting are selected Adjust inter character delay symptom
28. eyboard from the host device 4 Connect the Y ends of the communication cable to the keyboard and keyboard port on the host device If necessary use the male female adapter cable supplied with the scanner for proper connections 5 Plug the external power supply required Optional into the power jack on the PowerLink cable Cable Check the AC input requirements of the power supply to make sure the voltage matches the AC outlet The outlet must be located near the Fi 7 equipment and be easily accessible UN 6 Connect AC power to the transformer 7 Focus will start to initialize All LEDs yellow white and blue will light for approximately 2 seconds then start to alternately flash When the scanner has finished initializing the LEDs will stop flashing and the unit will beep 3 times indicating that the scanner is ready for use 8 Turn on the host device Plugging the scanner into a port on the host system does not guarantee that scanned information will be communicated properly to the host system The scanner is shipped from the factory configured with default settings Please refer to the MetroSelect Single Line Configuration Guide MLPN 00 02544 or MetroSet2 s help files for instructions on changing the scanner s configuration In addition please check that the scanner and host system are using the same communication protocol N See power source caution statement located on page 6 of t
29. his manual INSTALLING THE SCANNER TO THE HOST SYSTEM Stand Alone Keyboard MS1690 47 1 Turn off the host device 2 Plug the male 10 pin RJ45 end of the PowerLink cable into the 10 pin socket on the Focus You will hear a click when the connection is made 3 Plug the other end of the communication cable into the host s keyboard port 4 Plug the external power supply into the power jack on the PowerLink cable Check the AC input requirements of the power supply to make sure the voltage matches the AC outlet The outlet must be located near the equipment and be easily accessible Figure 8 5 Connect AC power to the transformer 6 Focus will start to initialize All LEDs yellow white and blue will light for approximately 2 seconds then start to alternately flash When the scanner has finished initializing the LEDs will stop flashing and the unit will beep 3 times indicating that the scanner is ready for use T Turn on the host device Plugging the scanner into a port on the host device does not guarantee that scanned information will be communicated properly to the host device The scanner is shipped from the factory configured with default settings Please refer to the MetroSelect Single Line Configuration Guide MLPN 00 02544 or MetroSet2 s help files for instructions on changing the scanner s configuration In addition please check that the scanner and host system are using the sa
30. ice complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Notice This Class A digital apparatus complies with Canadian ICES 003 Remarque Cet appareil num rique de classe A est conforme a la norme canadienne NMB 003 European Standard Warning This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Funkstoreigenschaften nach EN55022 1998 Warnung Dies ist eine Einrichtung der Klasse A Diese Einrichtung kann im Wohnbereich Funkst rungen verursachen In diesem Fall kann vom Betreiber verlangt werden angemessene Massnahmen durchzuf hren Standard Europeo Attenzione Questo e un prodotto di classe A Se usato in vicinanza di residenze private potrebbe causare interferenze radio che potrebbero richiedere all utilizzatore opportune misure Attention Ce produit est de classe A Dans un environnement domestique ce produit peut tre la cause d interf rences radio Dans ce cas l utiliseteur peut tre amen predre les mesures ad quates REGULATORY COMPLIANCE EMC Class B Devices The following is applicable when the scanner cable is less than 3 meters 9 8 feet in length when fully extended Les
31. instructions ci dessous s appliquent aux cables de scanner ne d passant pas 3 m tres 9 8 pieds de long en extension maximale Folgendes trifft zu wenn das Scannerkabel kurzer als 3 Meter ist This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is conne
32. is being transmitted If the scanner does not beep once and the white light does not turn on then the bar code has not been successfully read Short Razzberry Tone This tone is a failure indicator see Failure Modes on page 18 Long Razzberry Tone This tone is a failure indicator see Failure Modes on page 18 Three Beeps At Power Up When Focus first receives power it will start an initialization sequence All LEDs yellow white and blue will light for approximately 2 seconds then start to alternately flash When the scanner has finished initializing the LEDs will stop flashing and the unit will beep 3 times indicating that the scanner is ready for use Three Beeps Configuration Mode When entering configuration mode the white LED will flash while the scanner simultaneously beeps three times The white and blue LEDs will continue to flash while in this mode Upon exiting configuration mode the scanner will beep three times and the LEDs will stop flashing When configured 3 beeps can also indicate a communications timeout during normal scanning mode When using single code configuring the scanner will beep three times a normal tone followed by a short pause a high tone and then a low tone This indicates that the single configuration bar code has successfully configured the scanner 16 SCANNER OPERATION Visual Indicators IERE The MS1690 has three LED indicators yellow white and blue located on the t
33. lo scanner per guardare dentro l apparecchio Facendolo potete esporVi ad una radiazione rischiosa L uso di apparecchi ottici equipaggiati con raggi LED d emettitori di luce aumenta il rischio di danni alla vista 39 REGULATORY COMPLIANCE EMC Emissions FCC Part 15 ICES 003 CISPR 22 EN 55022 Immunity CISPR 24 EN 55024 Class A Devices 40 The following is applicable when the scanner cable is greater in length than 3 meters 9 8 feet when fully extended Les instructions ci dessous s appliquent aux cables de scanner d passant 3 m tres 9 8 pieds de long en extension maximale Folgendes trifft zu wenn das Scannerkabel langer als 3 Meter ist This equipment has been tested and found to comply with limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at their own expense Any unauthorized changes or modifications to this equipment could void the user s authority to operate this device This dev
34. me communication protocol A See power source caution statement located on page 6 of this manual INSTALLING THE SCANNER TO THE HOST SYSTEM IBM MS1690 11 1 Turn off the host device 2 Plug the male 10 pin RJ45 end of the MVC cable into the 10 pin socket on the Focus You will hear a click when the connection is made 3 Connect the other end of the MVC cable to the host device MVC Cable 4 Turn on the host device PF CoD 5 Focus will start to initialize All LEDs yellow white and blue will light for approximately 2 seconds then start to alternately flash When the scanner has finished initializing the Host end LEDs will stop flashing and the unit Gerges will beep 3 times indicating that the S dependent scanner is ready for use i Figure 9 Plugging the scanner into a port on the host system does not guarantee that scanned information will be communicated properly to the host system The scanner is shipped from the factory configured with default settings Please refer to the MetroSelect Single Line Configuration Guide MLPN 00 02544 or MetroSet2 s help files for instructions on changing the scanner s configuration In addition please check that the scanner and host system are using the same communication protocol A See power source caution statement located on page 6 of this manual 10 INSTALLING THE SCANNER TO THE HOST SYSTEM Integrated USB Full Speed MS1690 40 Low Spe
35. ocated on the underside of the head This label provides the unit s model number date of manufacture serial number CE and caution information The following figure gives an example of the label and its location Manufactured in Blackwood New Jersey U S A by Metrologic Instruments Inc December 2006 D 47 5V Warranty void if case is opened Contains no user serviceable components See User s Guide for patent coverage Complies with FCC and ICES 003 7 77 JM Figure 5 Label Samples and Location Caution To maintain compliance with applicable standards all circuits connected to the scanner must A meet the requirements for SELV Safety Extra Low Voltage according to EN IEC 60950 1 To maintain compliance with standard CSA C22 2 No 60950 1 UL 60950 1 and norm EN IEC 60950 1 the power source should meet applicable performance requirements for a limited power source Maintenance Smudges and dirt can interfere with the proper scanning of a bar code The output window should be routinely cleaned with glass cleaner sprayed onto a lint free non abrasive cloth INSTALLING THE SCANNER TO THE HOST SYSTEM RS232 MS1690 14 1 Turn off the host device 2 Plug the male 10 pin RJ45 end of the PowerLink cable into the 10 pin socket on the Focus You will hear a click when the connection is made 3 Connect the 9 pin D type connector of the communication cable to the proper COM port of the hos
36. onents MLPN 46 00147 Figure 11 Stand Components Item Description Stand Base 8 Round Head Wood Screw 12 STAND KITS Hard Mounting the Stand Optional Metrologic provides two 8 wood screws for securing the stand base to the counter top The following figure provides the pilot hole dimensions for securing the stand base Drill Two 39 Pilot Holes for 8 Round Head Wood Screws Figure 12 Stand Base Hole Pattern Not to Scale STAND KITS Assembling the Stand E V 20x 3 Flat Head Phillips 100 Undercut amp Scanner Cradle Orient the scanner cradle so that the flexible shaft s flat surface is facing the body of the scanner cradle lt t Flexible Shaft Cover Flat Surface 4 Flexible Shaft Position the flexible shaft so that the flat surface on the end is flush against the tab Stand Base on the stand base El lt Ys 20x Flat Head Phillips 100 Undercut Figure 13 Assembling the Stand 14 SCANNER OPERATION Two Default Modes of Operation CodeGate Out of Stand 1 The IR detects an object in the IR activation range and automatically turns on linear illumination 2 Aim the scanners line of light over the bar code 3 Pull the trigger to initiate scanning The
37. op of the scanner When the scanner is on the flashing or stationary activity of the LEDs indicates the status of the current scan and the scanner No LEDs are Illuminated The LEDs will not be illuminated if the scanner is not receiving power from the host or transformer The scanner is in stand by mode Present a bar code to Figure 15 the scanner and the blue LED will turn on when the IR detects the object Steady Yellow The yellow LED is illuminated when the scanner is in the stand Steady Blue The blue LED is illuminated when the scanner is active and linear illumination is on or when the scanner is attempting to decode a barcode Steady Blue and Single White Flash When the scanner successfully reads a bar code it will beep once and the white LED will turn on indicating data is being transmitted If the scanner does not beep once and the white light does not turn on then the bar code has not been successfully read Steady White When the scanner successfully reads a bar code it will beep once and the white LED will turn on indicating data is being transmitted After a successful scan the scanner transmits the data to the host device Some communication modes require that the host inform the scanner when data is ready to be received If the host is not ready to accept the information the scanner s white LED will remain on until the data can be transmitted Alternating Flashing of Blue and White This in
38. rologic Single Line Configuration Guide MLPN 00 02544 This manual can be downloaded for FREE from Metrologic s website www metrologic com MetroSet2 This user friendly Windows based configuration program allows you to simply point and click at the desired scanner options This program can be downloaded for FREE from Metrologic website www metrologic com or set up disks can be ordered by calling 1 800 ID METRO Serial Configuration This mode of configuration is ideal for OEM applications This mode gives the end user the ability to send a series of commands using the serial port of the host system The commands are equivalent to the numerical values of the bar codes located in the MetroSelect Single Line Configuration Guide MLPN 00 02544 UPGRADING THE FLASH ROM FIRMWARE The MetroSet2 program is a functional component of Metrologic s new line of Flash based scanners This program allows the user of a Metrologic scanner to quickly upgrade to a new or custom version of firmware It requires the use of a personal computer running Windows 95 or greater and the use of a serial port The user merely connects the scanner to a serial port on the PC launches the MetroSet2 program and blasts off to new software upgrades Each MS1690 regardless of the version number or communication protocol can be upgraded In other words all RS232 14 keyboard wedge 47 IBM 468X 469X 11 low speed USB 38 and full speed USB 40
39. scanner s light output will start to flash as it attempts to scan the bar code If the trigger is released the scanner will stop trying to scan 4 When scanner successfully reads the bar code it will beep once the white BEEP WHITE LED LED will flash and the decoded data Ke will be transmitted to the host Figure 14 CodeGate Out of Stand Presentation In Stand 1 The IR detects an object in the IR activation range and the scanner s light output automatically starts to flash as it attempts to scan the bar code 2 The scanner continuously attempts to scan the bar code until either it succeeds or the bar code is removed from the scanner s field of view 3 When scanner successfully reads the bar code it will beep once the white LED will flash and the decoded data will be transmitted to the host For additional configurable modes of operation please refer to the MS1690 Focus Supplemental Configuration Guide MLPN 00 02065 SCANNER OPERATION Audible Indicators When the Focus is in operation it provides audible feedback These sounds indicate the status of the scanner Eight settings are available for the tone of the beep normal 6 alternate tones and no tone To change the tone refer to the MetroSelect Single Line Configuration Guide MLPN 00 02544 or MetroSet2 s help files One Beep When the scanner successfully reads a bar code it will beep once and the white LED will turn on indicating data
40. t device 4 Plug the power supply into the power jack on the PowerLink cable Check the AC input requirements of the power supply to make sure the voltage matches the AC outlet The outlet must be located near the equipment and be easily accessible 5 Connect AC power to the transformer Figure 6 6 Focus will start to initialize All LEDs yellow white and blue will light for approximately 2 seconds then start to alternately flash When the scanner has finished initializing the LEDs will stop flashing and the unit will beep 3 times indicating that the scanner is ready for use T Turn on the host device Plugging the scanner into a port on the host system does not guarantee that scanned information will be communicated properly to the host system The scanner is shipped from the factory configured with default settings Please refer to the MetroSelect Single Line Configuration Guide MLPN 00 02544 or MetroSet2 s help files for instructions on changing the scanner s configuration In addition please check that the scanner and host system are using the same communication protocol N See power source caution statement located on page 6 of this manual INSTALLING THE SCANNER TO THE HOST SYSTEM Keyboard Wedge MS1690 47 1 Turn off the host device 2 Plug the 10 pin RJ45 male end of the PowerLink cable into 10 pin socket on the Focus You will hear a click when the connection is made 3 Disconnect the k
Download Pdf Manuals
Related Search