FLASH 1500D 1500W DMX strobe User manual - Bax
Contents
1. FLASH 1500D 1500W DMX strobe User manual Safety instructions A WARNING A Always keep this device away from moisture and rain Hazardous electrical shocks may occur A WARNING A Only connect this device to a matching power outlet This device is intended to work on a specified AC currency Connecting this device to power outlets with other voltages may result in permanent damage and possible hazardous situations such as fire or electrical shocks A WARNING A Be careful with every operation of this device Touching live wires inside and outside the unit may cause hazardous electrical shocks This unit must be operated by or under the supervision of an adult This device is not suitable for children Every person involved with the installation operation and maintenance of this device has to Be qualified Follow the instructions of this manual Make sure there is no damage caused by transport If the device seems damaged from the outside do not use it and contact your dealer for more information and consultation To make sure the device maintains in perfect condition and for safe operation it is necessary for the user to follow the instructions and warning notes of this user manual Damage caused by improper use or modifications to the device are not covered by warranty This device does not have any user serviceable parts inside Servicing of this device needs to be done by qualified technicians Im2. Gently slide the glass panel out of the fixture and place it on a soft surface for example a cloth or towel Take out the lamp from its socket and replace it with a new one Mount the cover and screws in reverse order Technical specifications 1500W DMX strobe 1500W discharge tube lamp Automatic and DMX mode built in speed and dimmer knobs 2 channel DMX control speed dimmer High quality optics and reflector for optimal strobe effect High intensity light pulses fill the room with bright lighting Hanging bracket for easy installation to a truss system light stand ceiling or beam Solid feet for placement on a solid surface DJ booth table stage Input voltage 230V AC 50 Hz 110V 60Hz optional Power consumption 1500W Device Dimensions 450 x 176 x 223 mm Packaging dimensions 500 x 240 x 280 mm Weight 4 425 kg Connectors DMX 3p XLR male and female Attached cable with Schuko connector Connectors and wiring schematics DMX connections Electrical wiring sn AR nee Cable Pin International XLR mounting socket ALK mounting plug rown Live 1 Ground 1 Ground 2 Signal 2 Signal i Yellow Green 3 Signal 3 Signal
3. the glass is damaged or broken WARNING Do not use this fixture for a long period of time as the powerful and bright pulsating beams of light may cause disorientation Do not use the device longer than 20 seconds when the device is used in nearly complete darkness Strobe use The lifespan of the tube decreases when the flash rate is increased The lifespan of the tube decreases when the device is transported while the tube is still hot directly after use Box contents Box contents 1x FLASH 1500D Unit and accessory inspection Always use the supplied power cable to connect the unit to a power supply If the cable appears broken or has visible damage do not use it If the unit is not going to be used for a longer period of time disconnect it from the power supply and store it in a dust free environment Always check the unit for possible damage before use If you suspect that something is wrong with the unit do not connect it to a power source When you suspect that your unit is broken or damaged contact your local dealer or a certified technician to inspect the unit When your device does not generate any light do not look directly into the lens When the fixture suddenly produces a beam it may cause injury to your eyes Device overview Te ubittttt Power AC220V SOHz 1500W Lamp 1500W ADHAN Strobe tube Reflector Ventilation slots Bracket Power cord Fuse Safety eye
4. Speed adjustment Dimmer adjustment DMX dipswitch panel 10 DMX input 11 DMX output OAONOORWND Setting up the device To activate the unit connect the included power supply to the unit and a suitable 230V 50 Hz power outlet The unit will activate directly after it is plugged in to a wall outlet or other power source This device is equipped with dipswitches on the rear to determine the active working mode and or DMX address There are 10 dipswitches each with their own function The working modes can be activated by turning the dipswitches on and off in certain combinations Auto manual mode Dipswitch 10 on other dipswitches off DMX mode Dipswitch 10 off other dipswitches will determine the DMX address The DMX address is used to place the device on a certain channel in a DMX chain This makes controlling the device with a DMX controller easier Set the correct address by using the dipswitches Every switch has its own value and by combining values it is possible to choose every address between 1 and 512 Dipswitch 1 1 Dipswitch 2 2 Dipswitch 3 4 Dipswitch 4 8 Dipswitch 5 16 Dipswitch 6 32 Dipswitch 7 64 Dipswitch 8 128 Dipswitch 9 256 Example When you wish to turn the fixture to starting address 19 you add the highest numbers possible to select the channel When you want to set the device to DMX address 19 add dipswitch 5 2 and 1 16 2 1 19 The FLASH 1500D can be controlled with 2 DMX
5. channels Each channel has its own function DMX channel 1 Speed 0 512 slow to fast DMX channel 2 Dimmer 0 512 0 100 Installation and maintenance Bracket The FLASH 1500D is equipped with a mounting bracket This bracket is adjustable in angle for your convenience Always tighten the knobs on the sides enough to prevent the bracket from moving during use It is possible to mount a hook to the fixture to install it to a truss structure lighting stand ceiling or beam Attach a half coupler or G clamp and always use a safety cable when mounting the fixture in a hanging position Feet The FLASH 1500D is equipped with small feet on the bottom making it possible to place the fixture on a flat surface such as a table stage etc Never block the fan output never place the fixture on a hot surface to prevent damage and possible injury Cleaning Make sure to clean the exterior of the unit frequently as the build up of dust and dirt may have negative effects on the cooling and optics of the fixture The exterior of the unit can be cleaned with a damp cloth The optics of the fixture can be cleaned with a clean cloth or paper towel with the addition of a non aggressive glass cleaning solution Clean the fan outlet and the cooling vents with a small brush while using vacuum cleaner suction to remove any loose dust and or dirt Clean the exterior of this fixture once a month When using this fixture intensively the frequency
6. n corrosion is found on the fixture Every power or signal chassis connector should be mounted tightly Do not use the device when connectors are loose Do not use the power cord when the cores are visible Contact your dealer for a replacement if needed Avoid the buildup of dust and dirt Clean the exterior of the fixture every month with a dry or damp cloth When using the device intensively the cleaning frequency needs to be increased Fuses The main fuse of this device is to be found on the rear of the device In most cases directly next to the power inlet Only replace a fuse for a new one with the same type and rating Do not use a fuse with a higher or lower rating Do not bridge the fuse with electrical wires aluminum foil as the fuse is used for protection against electrical shocks and short circuit Always mount the fuse cover back to the fuse compartiment Strobe guidelines WARNING Do not use this device when you or anybody around you is oversensitive for intense lighting and flashes This device is capable of producing intense pulsating light flashes and it is therefore not recommended to use this device in the direct environment of epilepsy patients as seizures may occur WARNING This device is equipped with a large glass lens Transport this fixture very carefully to prevent damage to the glass Always transport the device in the original packaging or use a flightcase Do not use this fixture when
7. of maintenance needs to be increased Transport When using this fixture in mobile setups provide sufficient protection during transport Use the original packaging of this unit or use a professional flightcase with proper foam inlay This way the electronics optics and housing are protected against severe shocks exterior damage and failing electronics After use let the unit cool down for at least 10 minutes When using DMX use the black out option on your DMX controller This way the unit is positioned in a static stand by mode and the internal fan is able to cool down the internal electronics which decreases the chance of damage during transport Replacing the bulb There is already a sufficient bulb installed in this feature The bulb should work when you try the fixture for the first time If this is not the case contact your dealer for a replacement or return the product It is normal that the bulb needs to be replaced when used for a long time as the lifespan will eventually come to an end Always use a lamp of the same type and rating to prevent overheating and possible damage to the fixture Never use a lamp stronger than 1500 Watt Do not touch the bulb with bare hands as this might have negative influence on the lifespan of the lamp To replace the lamp follow the steps below Remove the four screws located on the left of the fixture seen from the front where the lens and bulb are visible Remove the side panel
8. portant notes regarding safety and health Never let the power cord come in contact with other cables Handle the power cord and all connectors with the mains with caution Never remove any warning or informative labels from the unit The ground contact always needs to be connected Do not cover or remove the ground contact Never leave cables lying around Do not open the device and do not modify any hard or software of this unit Do not insert this object into air vents Do not connect this device to a dimmerpack Do not switch the system on and off frequently as this will reduce the lifespan of the device Do not drive the inputs of the fixture with a signal larger than required to work at full performance Only use this device indoor avoid contact with water moist or other liquids Do not place items filled with liquids on top of the unit Avoid nearby flames or heat sources do not place this device near flammable liquids gas or flammable items Always disconnect the device when it is not in use for a longer period or time when servicing is needed or when the device needs cleaning Only handle the power cord by its connectors Never pull the cable to remove a connector from its socket as this could lead to damage and electrical shocks Always operate this device with a stable AC current Always operate this device with the AC ground wire connected to the electrical system s ground Never use other
9. s and collission during use and transport Do not transport the device while in use Avoid brute force during the installation and operation of this device Familiarise yourself with the functions of the device before use Do not allow operation of the device by unskilled or unqualified people Use of the device in other ways than described in this user manual may cause damage and injury Ayra does not take responsibility for any damage or injury caused by improper use Storage and transport This device is intended for mobile use When transported use the original packaging of the product or a fitting flightcase preferably filled with foam This device is not intended forpermanent use Operation breaks will ensure that the lifespan of the device remains unchanged If the device is not used for a longer period of time disconnect it from its power source and store it in its original packaging or in a fitting flightcase Store the device indoor dry and do not expose the device to extreme temperature differences Housing Inspect the housing of the device frequently Severe dents cracks and missing screws should be avoided at all costs Do not use the device when the housing is not in optimal condition Contact your dealer or a skilled technician when in doubt about the state of the device Check the fixture and screws for corrosion Corrosion should not be present on the fixture Contact your dealer or a skilled technician whe
10. types of cables than specified in the manual do not use defective or bad functioning cables Contact your dealer when the included or required cables do not work properly with this device When the device has been exposed to large temperature differences for example transport from outdoor to indoor do not connect the device immediately Do not activate the unit until it has reached room temperature as moist might build up inside the unit which may cause shortcuts and or electrical shocks Guidelines and types of use This device is intented to be used by professionals on stage in theatres clubs and other equal venues This device is not suitable for children and always needs to be operated by an adult Only use the device when the environment is suitable and will not cause any damage Do not use the product in moist or dusty environments or where long term damage may occur such as indoor swimming pools where chlorine is used Beaches where sand and salt are present Outdoor without roof protection Indoor areas where intense heat sources are present or where the temperature exceeds levels which are comfortable for humans Only use the included power adapter and only connect the device to a suitable power outlet with the correct output voltage Connecting the device to a power outlet with the wrong type of voltage or using the prodcut with a wrong type of power supply may cause permanent damage to the device Avoid shock
Download Pdf Manuals
Related Search