ShuffleBox User Manual V1.1
Contents
1. 00 milliseconds inthe main window select your ee MIDI interface Destination o ZID a a haa Eae SysEx receive timeout 1 second HH 250 msec 500 msec 750 msec 1 sec To upload the SysEx data click Add and then select the firmware and click Open The firmware is now listed in the program s library Select it and click the Play button on the top don t forget to select the right MIDI port The status LED should start blinking until the upload process is finished When done restart power off on the ShuffleBox to deactivate the bootloader2. ShuffleBox User Manual V1 1 October 09 ShuffleBox User Manual V1 1 STAR STOP 1NO_3NAS Ino IGIN tre NINAS NI IOIW ees gm 5 o F pg E A A A a DIN sync OUT MIDI OUT DIN sync IN MIDI IN 9 24V DC gt 100mA Figure 1 Overview Routing ShuffleBox has 1x MIDI input 1x MIDI output 1x DIN sync input and 1x DIN sync output With the input selector switch you can choose between DIN sync and MIDI as the input DIN sync as input The incoming DIN sync data is processed and output on DIN sync OUT and on MIDI OUT gt The device works as DIN sync to shuffled DIN sync and DIN sync to shuffled MIDI converter MIDI as input The incoming MIDI sync data is processed and output on MIDI OUT and DIN sync OUT All other MIDI data is sent directly to the output without any processing Note Shuffled MIDI sync may only work with older gear New gear often performs a clock interpolation which corrects irregular timing gt The device works as MIDI to shuffled MIDI converter and MIDI to shuffled DIN sync converter SHUFFLE Potentiometer As you rotate the pot clockwise the shuffle amount will increase With the pot in complete counter clockwise position the shuffle algorithm is disabled ShuffleBox does not support triple metre Status LED Off power not connected ShuffleBox off ShuffleBox User Manual V1 1 October 09 Flashing at 1 4th Master sequencer running synced devices running Flashing at 1 8 Master sequence
3. h the MIDI input connected to your computer you can then load the SysEx file containing the new firmware PC MidiOX www midiox com Configure Settings y Low Level Input Buffers start the software Size 256 Bytes go to Options gt MIDI Devices Cancel select your MIDI output and click OK a L go to View gt SysEx inthe new window go to Sysex gt Configure enter the following parameters Low Level Output Buffers Delay Size 256 1 Bytes a Num 16 MiliSeconds Between Buffers Delay After F7 500 MilliSeconds Don t Warn to Save Changes Append To Bytes in Display Window Show FO F in colored text Save Dump directly to a file ShuffleBox User Manual V1 1 October 09 To send the SysEx data go to the SysEx window from the main window View gt SysEx and then select Command Window gt Load File After you opened the new firmware file select Command Window gt Send Sysex The status LED should start blinking until the upload process is finished When done restart power off on the ShuffleBox to deactivate the bootloader Mac SysEx Librarian www snoize com e9 SysEx Librarian Preferences General Transmit Speed 4 Settings SysEx Folder Location start the software goto SysEx Change Librarian gt Preferences E enter a value of about 500 Show file size as Abbreviated 1 2 KB milliseconds for Pause between ia oe played messages Pause between played messages 5
4. r running synced devices paused SART STOP Button This button enables you to send a STOP START signal to the synced device while the main sequencer is still running With the main sequencer running push this button once to stop the device attached to ShuffleBox at the end of the beat The status LED will start flashing at a higher rate while the device is paused Push this button again to start the synced device on the next beat Note only 4 4 supported Power Supply To operate this device you will need a power supply of 9 24V gt 100mA As soon as power is connected the device is ready to be used Firmware Update New firmware versions can be loaded via MIDI using the ShuffleBox s bootloader To activate this bootloader perform the following steps 1 Disconnect the power supply power off 2 Turn the shuffle potentiometer in full CW position 3 While turning on the device rotate the potentiometer in CCW direction This step has to be done quite fast 4 If done right the LED will flash for about 1 2 seconds showing that the bootloader has successfully been loaded If not repeat steps 1 3 until you are successful Don t update your ShuffleBox with a MIDI interface with known transmission issues Your ShuffleBox might end up with a non working firmware This however can always be fixed with a working MIDI interface In general updating the firmware works with every USB2MIDI interface even with a cheap 5 device Wit
Download Pdf Manuals
Related Search