S4 HID User Manual.fm
Contents
1. air You may also wipe the reflector with a clean lint free cloth If either method is not sufficient follow the instructions below You will need a Phillips screwdriver to complete this procedure 1 Remove the barrel rotation knob located at the bottom of the barrel Use a Phillips screwdriver to remove the retainer bolt located on top of the reflector housing Rotate the barrel 45 in either direction Carefully remove the barrel from the reflector housing Dampen a clean lint free cloth with alcohol or distilled water Alcohol is recommended Gently wipe the reflector Insert the barrel into the reflector housing with the iris pattern slot on top Line up the triangles on both parts While pressing in gently rotate the barrel 45 clockwise until it sets into position Then rotate the barrel counterclockwise 45 The barrel should be firmly attached and the triangles should line up again Replace the barrel rotation knob and tighten the retainer bolt 6 Source Four HID Source Four HID 7 Electronic Theatre Controls North America 3030 Laura Lane Middleton Wisconsin 53562 USA e Tel 1 608 831 4116 Fax 1 608 836 1736 Europe 5 Victoria Industrial Estate e Victoria Road London W3 6UU gt Tel 44 181 896 1000 e Fax 44 181 896 2000 Asia Room 605 606 e Tower Ill Enterprise Square e 9 Sheung Yuet Road Kowloon Bay e Hong Kong Tel 852 2799 1220 e Fax 4852 22. the lens in place Remove the lens from the tube 3 Dip the lens in a clean alcohol water mixture 10 alcohol 4 Use a moistened nylon bristle brush to wash the lens smooth side in a linear non circular motion 5 Use the same brush to lightly wash the lens ridged side by following its ridges 6 Dip the lens in a clean alcohol water mixture 10 alcohol 7 Dry the smooth and ridged surfaces with an air gun Make sure that the air flow moves liquid away from you 8 Inspect the lens for dirt Repeat steps 3 7 if necessary 9 Set the lens back in the lens tube with the ridged side facing the front of the tube Replace the lens brackets 10 Slide the lens tube back into the barrel with gel frame retainer on top Replace beam focus knob Lens locations 19 6x16 26 6x12 Red dot 9 Black dot 9 The different lenses used in the Source o ad UN Four are not interchangeable When 0 oO I 1 n installing a new lens refer to the adjacent 6 HH illustration for proper placement Also remember to have the lens color designator dot facing the color frame Ane Taani 36 6x9 7 50 4 5x6 Dotless Yellow dot gt Figure 10 Source Four HID 5 Cleaning the reflector WARNING Disconnect the power to the fixture before attempting to clean the reflector To quickly clean the reflector remove the lens tube and clean the dust from the reflector with a blast of oil free
3. 2 Slide the cover completely forward to expose the slot 3 Insert the iris or motorized pattern device For an iris install the flat side toward the shutters and make sure that the iris handle extends from the slot 4 Slide the slot cover back toward the shutters until it meets the iris handle Leave enough space to move the iris handle 5 Secure the drop in iris slot cover by tightening the screws Retaining clip in the C locked position Figure 3 Pattern holders A size holds 3 diameter patterns D sire holds 2 75 and 2 5 diameter patterns Drop in iris slot 3 Figure 5 Source Four HID 3 Rotating the barrel assembly 1 Loosen the barrel rotation knob directly behind the shutters on the underside of the reflector housing Figure 6 Do not remove the barrel rotation knob 2 Rotate the barrel to the desired position up to 25 in either direction from the centered position 3 Once the barrel is positioned tighten the barrel s rotation knob to lock it into position Barrel rotation knob Figure 6 C clamp mounting instructions C clamp not included The C clamp attaches the fixture to the mounting pipe and allows you to adjust the position of the fixture once it is mounted Figure 7 1 Tightly fasten the C clamp to the yoke with the provided yoke bolt and lock washer 2 Insert and tighten the Pan screw Note A Canopy mounting option is also available Adjust
4. 799 9325 World Wide Web http www etcconnect com Email mail etcconnect com Specifications subject to change Source Four HID is protected by US patent numbers 5 345 371 5 446 637 and 5 544 029 Part number 7060M1016 Copyright 2000 Revised 03 00
5. Source Four HID Lamp housing Ballast Retainer bolt Shutters Pattern holder slot Drop in iris Color frame Barrel rotation knob Retaining clip arrel 1 0 T focus knob Lens tube Color frame holder lt 4 Lamp type and general information Do not use lamps other than the following lamp type in Source Four HID fixtures Use of lamps other than specified below will void UL cUL safety compliance and your warranty e Source Four HID is suitable for damp locations Can be canopy mounted e No recessed mounting Caution Source Four HID is NOT dimmable Dimming will damage ballast and void warranty Lamp Type Manufacturing Codes Watts Base Bulb LCL Ave Initial Color Hrs lumens temp CDM T 150W 830 150 G12 T6 56mm 9000 14000 3000 K CDM T 150W 942 150 G12 T6 56mm 9000 12700 4000 K Ceramic Metal Halide MD150T6 U G12 830 0 G12 T6 56mm 9000 14000 3000 K MBI150 T 30 150 G12 57mm 6000 11500 3000 K MBI150 T 40 150 G12 57mm 6000 11250 4000 K Table 1 HID lamp reference Ballast information Caution The Source Four HID cannot be dimmed e Acceptable voltage is 120V 1096 50 60HZ only Operating current of 1 5 Amps e nrush current of 14 Amps Room ambient temperature should not exceed 104 F 40 C e Lamp ignition voltage is 4 5Kv non hot restrike Ballast case temperature
6. aining clip The color frame holder is equipped with a spring loaded retaining clip that prevents color frames and accessories from falling out Figure 3 WARNING Make sure all color frame accessories are locked in position with the retaining clip before hanging the Source Four HID 1 Release the retaining clip by pushing it sideways while gently pulling backwards 2 Insert the color frame 3 Lock the retaining clip by pushing sideways while gently pushing forward Shaping the beam You may shape the beam with the shutters a pattern an optional drop in iris or by rotating the barrel Pattern projection The pattern holder slot is on the top side of the barrel and in front of the shutters It accommodates A size B size and glass pattern holders Figure 4 Note Because the Source Four HID gate is 3 12 inches ETC recommends using A size patterns for maximum pattern effectiveness Use an optional donut in the accessory holder to enhance pattern projection Donut diameter range should be 2 5 to 2 75 inches Drop in iris slot The drop in iris slot is located on the top of the barrel and in front of the pattern holder slot It accommodates either a drop in iris or a motorized pattern device When the slot is not in use a small sheet metal cover secured with two Phillips screws prevents light leakage Figure 5 1 Use a Phillips screwdriver to loosen the screws on the drop in iris slot cover Do not remove the screws
7. endations when cleaning and inspecting lenses and reflectors Do not use glass or window type cleaners on lenses glass or polymer or reflectors Do not use abrasive materials such as steel wool Replace lenses if they contain visible damage cracks or deep scratches that may impair their effectiveness Cleaning 19 26 36 and 50 glass lenses 1 Remove the beam focus knob at the bottom of the barrel Remove the lens tube from the barrel Note t is not necessary to remove the lens for cleaning If you do remove the 195 26 or 50 lens make sure the identifying paint dot is not removed during cleaning See Lens Locations below 2 Dampen a clean lint free cloth with vinegar or household ammonia You may also use water but it will leave spots that can be removed by gently polishing the lens with a clean and dry cloth 3 Starting from the center gently wipe the lens 4 Slide the lens tube back into the barrel with the color frame retaining clip on top Replace the beam focus knob Cleaning 5 and 10 polymer lenses To quickly clean the lenses remove dust with a blast of oil free air If this is not sufficient follow the instructions below You will need a Phillips screwdriver Caution Handle polymer lenses by their edges only Never rub anything dry ona polymer lens 1 Remove the beam focus knob Gently pull the lens tube out of the barrel 2 Use a Phillips screwdriver to remove the brackets that hold
8. ing the C clamp SA Pipe boit The C clamp attaches the fixture to the mounting pipe and allows you to adjust the Yoke bolt position of the fixture once it is mounted Figure 7 2 Loosen the C clamp pan screw and rotate the yoke to the desired position ock washer Yoke 1 Place the C clamp on mounting pipe then tighten the pipe bolt to secure it 3 Tighten the pan screw to lock the fixture into position SS Adjusting the yoke position Figure 7 The Source Four HID provides multi positioning capabilities within its yoke for overall fixture height and angle Setting the fixture height within the yoke High position The Source Four HID has a two position yoke for modifying the overall height in which Tnm the fixture is mounted Figure 8 To change the height position do the following p 1 Remove the yoke locking knobs washers and hex bolts from either side of the fixture 5 3 Replace the yoke s hex bolts washers and locking knobs Figure 8 2 Raise or lower the fixture to the desired position within the yoke 4 Tighten the yoke knobs to secure the fixture in position Setting the angle within the yoke 1 Loosen the yoke locking knobs Do not remove them 2 Tilt the fixture to the desired position Figure 9 3 Tighten the yoke locking knobs to secure the fixture in position 4 Source Four HID cleaning ETC offers the following recomm
9. should not exceed 167 F 75 C The ballast is attached to the Source Four yoke by two screws non remotable Source Four HID 1 Installing or replacing the lamp A lamp must be installed before you use the fixture Note Verify that the lamp you intend to install is correct Replace the lamp if it becomes damaged or thermally deformed WARNING Let the lamp cool before replacing 1 Disconnect power to the Source Four HID before installing the lamp 2 Loosen the knurled bolt on the back of the lamp housing and pull the housing out 3 Holding it by the base remove the lamp from its box Note To avoid premature lamp failure do not touch the lamp glass If you do clean it carefully with rubbing alcohol and a clean lint free cloth before operation 4 Insert lamp base into socket assembly as show in Figure 1 5 Push down on the lamp base until the lamp seats firmly Caution Improperly installed lamps cause premature lamp failure and socket problems 6 Reinstall the lamp housing by aligning the bolt hole and tightening the knurled bolt Focusing the beam 1 Loosen the beam focus knob located under the barrel as shown in Figure 2 2 Slide the lens tube forward or backward to achieve the desired beam edge 3 Once the fixture is focused tighten the beam focus knob HID Lamp Lamp base Lamp housing Figure 1 Beam focus knob Figure 2 2 Source Four HID Color frame ret
Download Pdf Manuals
Related Search