INSTALLATION MANUAL PC-408 Paper Feed Cabinet
Contents
1. INSTALLATION MANUAL Applied Machines d Color MF360 MF280 MF220 COLOR MFP 36 ppm 28 ppm 22 ppm Product Code AOED Note Lifting the machine in an awkward position or transporting it in a poorly balanced position could Screw B result in personal injury When transporting the 4 x 8 mm machine assign an adequate number of persons to the job and ensure that each person can take a good position of not being excessively loaded Screw C mass approx 30 5 kg 67 Ib 4 x 10 mm I Accessory parts Installation manual Name 4038IXC033DA 40381XC033MA No Name 1 Fixing leg A 4980IXC019MA WARNING After unpacking be sure to get rid of the Q packaging materials and keep them out of Fixing leg B the reach of children Putting the head in the plastic bag involves danger of suffocation 4348U020MB Fixing leg Note cover A This manual provides the illustrations of the acces sory parts and machine that may be slightly differ ent in shape from yours In that case instead of the illustrations use the appearance of your 4848U099MA machine to follow the installation procedure This Fixing leg does not cause any significant change or problem cover B with the procedure Note When removing the paper feed cabinet from its 4348U099MB shipping carton do not hold the reinforcement Fixing bracket as a personal injury or a deformed fra2. ange enter the correction value using the or key 3 Paper exit direction xo 4061IXC152DA Produce another test print and check to see if width A falls within the specified range Touch END 6 Touch Exit on the Service Mode screen 7 Turn OFF and ON the Main Power Switch Note When displayed the Service Mode screen be sure to turn off the main power after exiting the Service Mode screen and wait for 10 seconds or more before turning on 5 Y111190 9
3. be placed upside down 16 AOXWMXC028MA 17 Slide the drawers back in 18 Move the machine and paper feed cabinet to the installation site Then adjust the two adjusters at the front to let the paper feed cabinet sit on the floor AOXWMXC106MA Y111190 9 19 Install the fixing leg A s at two locations in the front shown in the illustration six screw B s fur nished with the paper feed cabinet Note When mounting the finisher at the same time do not install the fixing leg A or fixing leg cover A at the left front side CAUTION To reduce the risk of injury due to unsta ble equipment set stabilizers before use WD AOXWMXC029MA 20 Install the fixing leg cover A s two pieces at two locations in the front shown in the illustration Note e Insert the fixing leg cover A s in the direction shown by arrow until they click into position e Insert the protruded portions of the fixing leg cover A s shown by the arrows into the fixing leg AOXWMXC030MA Y111190 9 E 5 21 Install the fixing leg A left rear and the fixing leg B right rear shown in the illustration Tighten the screw C s into the hole A s to install the fixing leg B Fixing leg A three screw B s furnished with the paper feed cabinet Fixing leg B four screw C s furnished with the paper feed cabinet Note If the scre
4. elease of right door and open the right door Detach the protruded portion of the right door from the paper feed cabinet to remove the right door AOXWMXCOSOMA 10 Remove the harness cover and the three fixing screws to remove the plate AOXWMXC051MA Installation Manual 11 Loosen the adjusting screw and turn the screw D clockwise or counterclockwise as necessary Note Use care not to damage or dent the paper path surface inside the right door AOXWMXCO052MA e If width A is greater than the specified value turn the screw D counterclockwise A093IXC079DA e If width A is greater than the specified value turn the screw D clockwise A093IXCO80DA 12 Load paper and let the machine produce another test print Then check width A Make the adjustment until width A falls within the specified range 13 Tighten the adjusting screw which has been loosened in step 11 Installation Manual E 8 lt Centering Duplex 2nd side gt 1 Touch Centering Duplex 2nd side 2 Touch 3rd and then press the Start key A test print will then be produced Measure width A of the test pattern on the back side of the test print produced and check that it falls within the specified range Specifications 3 0 mm 2 0 mm Adjusting the Paper Reference Position If the measured width A falls outside the specified r
5. l of the paper stack does not exceed the W MAX paper level indica tor Se AOXWMXC034MA AOXWMXCO035MA Y111190 9 M Making settings for paper size 1 Display the Service Mode screen For details of how to display the Service Mode screen see the Service Manual Touch System 2 Touch LCT Paper Size Setting Check to see that A4 I is displayed with white text on black Touch END V Checking the paper reference position lt Centering gt 1 Touch Machine Touch Printer Area Touch Centering Touch 3rd and then press the Start key A test print will be produced Measure width A from the edge of the paper to the pattern printed on the test print and check that it falls within the specified range Specifications 3 0 mm 1 0 mm Adjusting the paper reference position If the measured width A falls outside the specified range enter the correction value using the or key 2 3 4 5 Paper exit direction 4061IXC147DA Produce another test print and check to see if width A falls within the specified range If the use of the Z3 or key does not allow the measurement to fall within the specified range perform the following steps Y111190 9 E 7 7 Press the drawer release button and then slide out the drawer from the paper feed cabinet AOXWMXC032MA Pull the r
6. me bracket A S could result Reinforcement bracket 4658U021AA Fixing bracket B A093IXC004DA Screw A black 4 x 8 mm 4038IXC033DA A093IXC027DA Y111190 9 E 1 Installation Manual Il Installation procedures 1 Turn off the machine 2 Remove the cord clamp and unplug the power cord from the machine one screw AOXWMXC031MA 3 Remove the protective tape from the paper feed cabinet Note Do not peel the tape that fixes the paper feed cab inet hookup harness in position until the machine is attached to the paper feed cabinet harness AOXWMXCO036MB AOXWMXC037MA Installation Manual 4 Insert the proper tool such as a screwdriver to the hole on the back of the paper feed cabinet to take out the drawer AOXWMXC038MB 5 Remove the shipping preservatives and protec tive tape from the inside of the drawer AOXWMXC039MA 6 Slide the drawer back in 7 Pull out the handles AOXWMXC101MA Y111190 9 Holding the transportation handles at the right 10 Peel the tape that fixes the paper feed cabinet and left of the machine place the machine onto hookup harness in position the paper feed cabinet When placing the machine use the positioning pins in the rear of the paper feed cabinet to align the machine cor rectly with the cabinet Note e Whe
7. n transporting or moving the machines assign adequate number of persons e When attaching the machine as the reference fit the machine with the corner A and B of the paper feed cabinet CAUTION aan When holding the transportation handles GD be careful not to catch your fingers in the 11 Connect the two connectors of the paper feed machine cabinet hookup harness to the machine AOXWMXCO003MB 12 Secure the paper feed cabinet to the machine by the two fixing bracket A s two screw A s fur nished with the paper feed cabinet AOXWMXC105MA 9 9 Remove the drawer rear under cover from the ee machine one screw AOXWMXCO001MB Y111190 9 E 3 Installation Manual 13 Reinstall the drawer rear under cover which has been removed in step 9 one screw AOXWMXCO0SMB 14 Insert the proper tool such as a screwdriver to the hole on the back of the paper feed cabinet to take out the drawer AOXWMXC040MB Installation Manual 15 Slide out the second drawer from the paper feed cabinet Secure the paper feed cabinet to the machine by the fixing bracket A right and the fixing bracket B left Fixing bracket A one screw A furnished with the paper feed cabi net Fixing bracket B two screw A s furnished with the paper feed cab inet Note The fixing bracket B can
8. w C s cannot be tightened into the hole A s because the machine is installed on cushioned floor such as a carpet use the hole B s CAUTION GD To reduce the risk of injury due to unsta ble equipment set stabilizers before use AOXWIXC002MA Installation Manual 22 Install the fixing leg cover A left rear and the fixing leg cover B right rear shown in the illus tration Note e Insert the fixing leg cover A and B in the direc tion shown by the arrows until they click into position e Insert the protruded portions of the fixing leg cover A and B shown by the arrows into the fix ing leg AOXWIXCO03DA 23 Plug the power cord into the machine and put the cord clamp that has been removed in step 2 through the power cord to install it one screw AOXWMXC031MA 1 Turn on the machine s main and sub power switches 2 Press the drawer release button and then slide out the drawer from the paper feed cabinet AOXWMXC032MA Installation Manual E 6 3 Align the edges of the paper stack and place the stack into the drawer Note Make sure that the top level of the paper stack does not exceed the W MAX paper level indi cator e Correct any curl in the paper before loading AOXWMXC033MA 4 Align the edges of the paper stack and place the stack into the drawer Note Make sure that the top leve
Download Pdf Manuals
Related Search