TB6560-3N User Manual - myhobby-CNC
Contents
1. 2 0 asoa noon noon 8 7x MATCHING THE 000000 9 6 1 ELECTRICAL WRRING ee ANAN 9 6 2 INPUT VOLTAGE AND OUTPUT CURRENT 5 000 000 400000 9 E CONTACTUS 2m ER ab a LA 11 TB6560 3N User Manual Introduction 1 1 Overview The TB6560 3N is a three axis bipolar 3 0A phase stepper motor microstepping driver with step and direction inputs DIP switch settable step mode full half eight and sixteenth M1 M2 Current 100 75 50 20 T1 T2 and decay mode 0 25 50 and 100 D1 D2 Using the model of the bipolar constant current chopper technology makes the motor operation and high precision small vibration low noise stable running safe and convenient is the majority of enthusiasts DIY and engraving machine manufacturers preferred products 1 2 Technical Specs gt Single chip motor driver for sinusoidal microstep control of stepping motors gt Five limiting interface gt Power on in indication led gt 3Amps 34Volts Supply voltages 12 34DC gt Full step half step eight step and sixteenth step selection with 1 M2 gt work Current 0 7A 1 75A 2 6A 3 5A selection with dipswitches SW1 SW22. gt 4 Wire 6 Wire 8 Wire stepper motors can be used gt Two phases bipolar driver gt Easy wiring with standard screw terminals gt Step frequency up to 100khz gt Standard parallel port interface list for MACH2 MACH3 KCAM4 TB6560 3N User Manual 1 3 Application domain Suitable for all kinds of small and medium sized automation equipment and apparatus For example laser machines laser engraving amp cutting machine laser subsurface engraving machine laser handicraft cutting machine nonmetal materials laser marking machine laser seals engraving machine and photosensitive seal machine TB6560 3N User Manual Electrical mechanical and environmental Specifications 2 1 electrical Specifications 2 2 Use of the environment and parameters Natural cooling or forced air cooling Away from heating equipment combustible gases Occasions and conductive dust avoid dust oil mist corrosive gas place too much humidity and strong vibration Temperatur 0O 50 C Humidity 40 90 RH Vibration 5 9m s2MAX 20 C 80 C 110g 2 3 Install the machinery unit mm TB6560 3N User Manual 130 25 TB6560 3N User Manual Drive connection and interface description 3 1 Wiring diagram To Manual control device Subdivision M1 M2 Decay Model 01 02
3. 1 Limit Switch 2 To Relay for four Way 1wiring diagram 3 2 Port Description 3 2 1 Control signal interface EN Enable control signal L1 Input limit interface 1 STEPX X Pulse signal L2 Input limit interface 2 DIRX X Direction signal L3 Input limit interface 3 STEPY Y Pulse signal LA Input limit interface 4 DIRY Y Direction signal RLY Relay control signal STEPZ Z Pulse signal L5 Input limit interface 5 DIRZ Z Direction signal GND GND TB6560 3N User Manual PY DIP switch current segments decay The drive using six DIP switch to setting current segments decay Mode 4 1 Current Settings Switch SwitchT2 current Explain ON ON 20 3 5A The current is OFF ON 50 3 5A better to closed to ON OFF 75 3 5A the motor rated OFF OFF 100 3 5A 4 2 Segments Settings SwitchM1 Switch 2 Segments Explain ON ON 1 8 When MI off M2 off drive OFF ON 1 16 segments number is 1 1 8 step angle ON OFF 1 2 motor turning circle the whole step OFF OFF 1 200 steps rev When OFF S4 ON 1 8 step angle motor turning circle the whole step 3200 steps 4 3 Decay Mode Switch D1 Switch D2 Decay Mode Explain ON ON Rapid decay Rapid decay is OFF ON 50 Rapid decay better when motor ON OFF 25 R
4. Large size of the motor torque is relatively large the current size of the primary and the inductance high speed performance of small induction motors but a larger current 6 1 Electrical wiring For the 6 8 line stepper motor connected in different coils of the motor performance quite different as shown below P2 P2 At At A A B B B 8 line motor parallel connection 4 line motor Good high speed performance P2 P2 A At N A A NC B B B B NC 6 line motor 6 line motor High torque mode High speed mode P2 At B B 8 line motor serial connection Low speed large torque 6 2 Input voltage and output current selection 1 Supply voltage setting In general the higher the supply voltage the greater the motor torque at high speed TB6560 3N User Manual High speed to avoid losing steps On the other hand the voltage is too high will lead to over voltage protection motor heat more and may even damage the drive When working at high voltage low speed movement of the vibration will be larger 2 Output current setting For the same motor the current setting value the greater the motor output torque but the current is large motors and drives are also more serious heat The size of the specific heat value not only with the current setting but also with the exercise type and duration The following is configured using the stepper motor rated current value as a reference but t
5. TB6560 3N User Manual TB6560 3N the Stepper Motor Driver Board User Manual YT PE SEAR SER BEE IR TB6560 3N User Manual catalog INTRODUCTION 12532035 GR4GRAG NAE NG KATIGAS NGARAN ARNAN RAR 2 De OVERVIEW 2 2 05 nine 2 1 2 TECHNICAL SPECS 2 2 22 ar bin V E nee 2 1 3 APPLICATION 1 04 8483 24 3 Z ELECTRICAL MECHANICAL AND ENVIRONMENTAL SPECIFICATIONS 4 24 ELECTRICAL 4 2 2 USE OF THE ENVIRONMENT AND 6 4 2 3 INSTALL THE MACHINERY UNIT 4 DRIVE CONNECTION AND INTERFACE DESCRIPTION cccccsssssssssscssssssccsssssecssseeee 6 9 6 3 2 PORT DESCRIPTION 22255 6 NY DIP SWITCH CURRENT SEGMENTS 2 7 4 1 CURRENT 6 5 7 Ai 2 SEGMENTS SETTINGS 220 7 4 3 7 FL POWER SUPPLY
6. apid decay has a high speed OFF OFF Slow decay TB6560 3N User Manual AH Power supply selection Power supply voltage DC12V 34V can work MD430 drive the best use of non regulated DC power supply can also be used step down transformer bridge capacitive filter rectifier capacitor desirable 6800uF or 10000uF However note should be rectified peak voltage ripple does not exceed 34V Recommend the use of 12V 34V DC power supply to avoid power fluctuations over drive voltage range If you use a regulated switching power supply switching power supply should be noted that the output current range to be set to maximum Note 1 The wiring should pay attention not to reverse the positive and negative 2 The best type of non regulated power supply 3 use of non regulated power supply the supply current output drive capability should be greater than 60 of current can be set 4 the use of regulated switching power supply power supply output current should be greater than or equal to the drive current 5 If electrical power is large enough two drivers can share a power supply 7x Matching the motor TB6560 3N User Manual Motor 4 6 8 two phase four phase hybrid stepping motor step angle of 1 8 degrees and 0 9 degrees can be applied Selected mainly based on the motor when the motor torque and current rating decision Torque motor size determined primarily by size
7. he practical application of best value should be adjusted on this basis In principle such as low temperature lt 40 C is appropriate to increase the current settings as needed to increase the value of the motor output power torque and speed response four and six wire motor speed mode The output current is set equal to or slightly less than the motor rated current value six lane high torque motor mode the output current is set to motor rated current 70 cight wire electrical series connection As the series resistance increases when the output current should be set to motor rated current 70 Motor and eight wire connection output current can be set to 1 4 times the rated motor current TB6560 3N User Manual Address High tech Development Zone Guangdong Province Shenzhen Technical support 13923726521 13798412235 Email 723701087 qq com 190601828 qq com Website http vascien taobao com 11
Download Pdf Manuals
Related Search