USER'S MANUAL
Contents
1. USERS MANUAL XIEGU TECH Copyright 2014 XIEGU Inc All Rights Reserved 1 12 Important reminder Security considerations Before operating the equipment please read our operating manual carefully and keep the manual so as not to lose Do not use equipment during a lightning Features Low noise single conversion HF transceiver Double balanced diode mixer for extended dynamic range O 2uV receive sensitivity preamp on Narrow band double tuned bandpass filters Damp proof covering all HF amateur frequencies including WARC bands IF channel AGC for constant gain at least Don t illegal operations provides 95db dynamic range High performance narrow band IF crystal filter with shape factor up to 1 7 Optional NB module Note RF high voltage of antenna connector Optional front and rear handles vanning list Qty 1 The main engine of the X 108 l Power supply cable 3 Hand microphone 1 4 USB Cable 1 Service card 1 2 12 Machine parameters Basic parameters Frequency range Receive 0 5 30MHz Continuous Transmitting All HF Amateur bands including WARC bands Operating mode SSB J3E CW AIA AM A3E minimum frequency stepping 1Hz Antenna impedance 50 Q Operating temperature range 10 C 60 C Frequency stability 1 5ppm Open the power about 1 mi2. 9 Britns i kni 12 DC 1 2 10 DDSCLK System Clock 11 DCLKx6 DDS multiplier settings 12 System Audio Settings 11 12 Item 1 to 5 cannot be freely modified otherwise 1t will lead to the transceiver exception or even not work Item 6 for CW Receiving side tone pitch adjustment Users can according to their preferences and habits adjusting CW side tone Item 7 for CW transceiver delay Users can operate according to their own habits appropriate changes this parameter to match the transmitters speed S D y N INSIDE XIEGU TECH Fee EK ARAS 12 12
3. 9 14 94 go 18 D 200 G LSB 2 ok SFPLT NES P cuit Hii gt gt DOD SPLT a e AUS SPLT Select SPLIT operating mode RIT Select RIT mode adjust via selector knob B setting shown on RIT display in LCD POW Set RF output power adjust via selector knob B level displayed via red line in LCD V M Select VFO or Memory mode Select ATT GES LOCAL PRE ee 11 90 14 Bi Un channel frequency using selector knob B 10 108 BAD wv M gt V In memory mode move current frequency to VFO and switch to VFO mode UFO LSE BZ s Bk SPLT HB4 MW In VFO mode store current frequency OUTILS a and settings in memory MC In memory mode clear selected memory channel BW Select Bandwidth 0 5 2 2 15 kHz ATT RmBCMPi i LOCAL PRE CHAD 11 90 14 FACE KEY Select keyer Manual Auto L Auto R KSPD Select keying speed adjust via selector knob B speed displayed under KEY in LCD TIME Set Internal Clock adjust via selector knob B select hour minute with Up Down buttons SQL Select to adjust Squelch level via selector knob B level shown on line display in LCD VCMP voice compression settings 6 12 G Pe hie ON ME CRM SN SUF frs HUAU Zz SIPH 0000 13 198 a QU es vron LSB 52 3k SPLT NB4 ti Li pae DT Ftc IT GC INURL sde FAST 3 3 Functions Operating Instructions 3 3 1 Set the current operating frequency Method 1 Press th
4. menu page then press V M Press this function key to move between frequency mode and channel mode 3 3 14 Move current channel to VFO Press the frequency knob to switch the current menu page then press M gt V The radio will switch to VEO mode showing information from the current channel 3 3 15 Save current settings to Memory Press the frequency knob to switch the current menu page then press V M to choose channel mode Turn the frequency knob until BLANK is highlighted Press V M to return to frequency mode Adjust frequency operating mode and other parameters desired then press MW to write this information to memory 3 3 16 Delete the current channel Press the frequency knob to switch the current menu page then press MC to clear the information stored in the current channel 3 3 17 Manual automatic telegraph key Press the frequency knob to switch the current menu page then press KEY Choose Manual Key Automatic Left Hand telegraph key or Automatic Right Hand telegraph key 3 3 18 Automatic telegraph key rate Press the frequency knob to switch the current menu page then press KSPD Turn the frequency knob to set the automatic key rate 3 3 19 Set the local time Press the frequency knob to switch the current menu page then press TIME 9 12 Then press the corresponding number Keys on the microphone to set the local time 3 3 20 Setting squelch level Press the frequency knob to switch the current m
5. b to switch the current menu page then press AGC AGC options are Fast or Slow with the screen showing the current status Press AGC again to exit 3 3 7 Noise Blanker on off 1f equipped Press the frequency knob to switch the current menu page then press NB The Noise Blanker offers depth of NB1 thru NB4 with the screen showing the current status 3 3 8 Switching between VFO A VFO B Press the frequency knob to switch the current menu page then press A B You can toggle between VFO A and VFO B 3 3 9 Set both VFO s to the same settings Press the frequency knob to switch the current menu page then press A B The settings of the current VFO will transfer to the second VFO 3 3 10 Split frequency operations Press the frequency knob to switch the current menu page then press SPLIT The radio will receive on VFO A and transmit on VFO B 3 3 11 RIT tuning Press the frequency knob to switch the current menu page then press RIT Turning the frequency knob will change the receive frequency but leave the transmit frequency unchanged Pressing RIT again will exit this mode 3 3 12 Transmit power setting Press the frequency knob to switch the current menu page then press POW The on screen power status will be highlighted Rotate the frequency knob to select the 8 12 desired power setting and press POW to exit 3 3 13 Switching between Frequency Mode Channel Mode Press the frequency knob to switch the current
6. e front panel UP DN button move to the desired frequency step bit bit then rotate the frequency knob to change the current frequency value 7 1 Method 2 On the multifunction digital microphone in hand Press a Ie h and then enter the frequency directly such as 14 27 then press the F INP ENT button again to complete the frequency settings 3 3 2 Mode Switching Method 1 Press the frequency knob to switch the current menu page then press MODE Press corresponding multifunction button to complete mode switching Method 2 On the multifunction digital microphone in hand press to complete the mode switching 3 3 3 Filter Switching Method 1 Press the frequency knob to switch the current menu page then press BW Press corresponding multifunction button to complete filter switching Method 2 On the multifunction digital microphone in hand press FIL to complete filter switching 3 3 4 Preamplifier on off Press the frequency knob to switch the current menu page then press PRE When the preamplifier is on PRE will be highlighted green When the preamplifier is off PRE will appear dark 3 3 5 Attenuator on off Press the frequency knob to switch the current menu page then press ATT When the attenuator 1s on ATT will be highlighted green When the attenuator 1s off 7 12 ATT will appear dark The attenuator provides 10 dB attenuation 3 3 6 Automatic Gain Control on off Press the frequency kno
7. enu page then press SQL Turn the frequency knob to set the squelch depth Press SQL again to save the squelch setting and exit 3 3 21 Set voice speech compression ratio Press the frequency knob to switch the current menu page then press VCMP Adjust the compression ratio as desired 3 4 Extended Interface r Pru RE ARPT ACE ds eee x FRET Ey ANT Antenna 50 ohms AUX Auxiliary PTT Audio Input GND AF IN PTT OUT PTT output voltage status RX O0V TX 5V SPK Speaker or Headphone 3 5 stereo Socket Otherwise it will damage the rig Before using the headphone please decrease the volume 10 12 KEYER Telegraph Key dot The telegraph key 1s automatic and manual integration You can switch in the menu USB PC control or firmware update DC IN 11 14 5 v DC input 3 5 Advanced Menu Settings CAUTION THESE SETTINGS ARE DIRECTLY RELATED TO THE CORRECT OPERATION OF THIS RADIO PLEASE EXERCISE CAUTION PLEASE RECORD AND SAVE ALL ORIGINAL FACTORY SETTINGS BEFORE MAKING ANY ADJUSTMENTS To enter menu setting mode Power off radio Press and hold Fl button while powering on 1 IF SSB SSB IF 2 IF CW CW IF berid 3 BFO LSB BFO value LSB mode Susten Settings 4 BFO USB BFO value USB mode N mn 0701361Hz 5 BFO CW BFO value of the CW mode 3 FO 6 CW Tone CW side tone pitch frequency 2 BED adjustment 6 CW 7 CW TDly CW launch delay e S8 8 TOT 2 Bri
8. ication 9 No function 10 Memory write button 11 Frequency Channel switching button 12 VFO A VFO B switching button 13 No function Operating instructions 3 1 Screen displays instructions 1 Preamplifier Pre attenuator current status 2 Current settings for frequency information 3 VFO current status Operating mode Split frequency transceiver status Filter bandwidth NB current status select keyer Manual Auto L Auto R O ee ae ee Channel Voice compression ratio Host Input Voltage 7 Local time 8 Multifunctional menu 9 S Meter 10 Real time power meter 11 Setting Power value 12 VSWR meter 13 Receive and Transmit current status 14 Frequency control display 15 AGC State display 5 12 gere 1 1 LOCH pe 10 100 BAA arr 357 5 40 a i i iS Les KYR RIT ANUAL FF Se ae in CMR SEE CHOO 11 ou 14 58 12 109 BAA err ie 3 ag HEH 155225 MODE Pes 5 pm ig 31 st tse ANL uen 1 a Ho 11 90 tae 7 PRE 2 oh 400 228 C 3 2 Menu Functions ITT Gach iii LOCAL PRE 18 100 nuy err PRE Switch receive preamp on or off ATT Switch receive signal attenuator on or off MODE Select desired operating mode CW AM LSB USB AGC Select AGC level FAST SLOW OFF co gt Zk YR RIT En m Re te NB Select NB level between 1 and 4 A B Switch between VFO A amp VFO B EMBCNP iti LOCAL pp A B Set VFOAthe same as VFO B RE CHOG 11
9. nute 10 C 60 C Standard Edition 0 5ppm Open the power about 1 minute 10 C 60 TCXO M Matching Operating voltage 12 14 5V DC Current draw Receiving 600mA Transmitting 7 5A Max Dimensions mm 120 45 180 mm Does not include the Front and rear handles and the Knob etc bulge Transmitter parameters Transmitter power Modulation mode SSB balanced modulation AM Low level modulation Spurious response rejection 40dBc Carrier suppression Z45dBc IF filter SSB 2 4kHz 6dB CW 500H7 6dB Receiving parameters IF Frequency 10 7MHz receive sensitivity 0 2uV Receive Frequency bands 1 8 2 Q0MHz 3 5 4 0MHz 5 0 5 5MHz 7 0 7 3MHz 10 0 10 2MHz 14 0 14 5MHz 18 0 18 2MHz 21 0 21 6MHz 24 8 25 0MHz 28 0 28 8MHz 0 5 30 0MHz Dynamic range Better than 95db RIT Frequency control range 1kHz audio output O0 5W 8 Q 3 12 D Description of equipment 2 1 Front panel Description O oo BR W N Power switch Volume knob Hand microphone socket Display screen Multifunction key Frequency knob UP key DOWN key 2 2 Rear panel Description Se oe Sn g SO 239 Antenna Jack Audio input PTT input Audio output CW key input USB port DC power input Ground connection 4 12 2 3 Microphone 1 Lock button Press it unlock again PTT button Up Down frequency channel Receiving indicator Multifunction Filter selection buttons Mode selection button No ind
Download Pdf Manuals
Related Search