IPMS-EVK-UHF RFID-Reader
Contents
1. Timeoutims 900 Continous Inventor E Enable Max cnt of messages 8 Place EPC here Output power dBm r gt 28 00 SkyeTek Reader Settings 32 50 E Reader operations RF Reset ms 2000 UHF Protocol metra Tec E0500 0000060E00000000 IWF 001 Status ready RF Field Reset 32 50 7 RFFieldOn RF Feld OF 32 50 v Reset Save Apply se Status ready Status ready Ay J se Figure 5 Reader settings of different RFID readers MetraTec Pulsar MX mid Impinj Octane SDK right SkyeTek Super Nova left IMPORTANT Settings needs to comply with local RFID regulations 2 5 Inventories To perform inventories the user has to select a task that contains the activity to search for existing tags and click on the Start Task button see Figure 1 Mark B Available tags and Date 2015 07 17 O Seite 7 von 10 IPMS EVK UHF Z Fraunhofer IPMS RFID Reader Software User Guide additional information will become visible at the readout section afterwards see Figure 1 Mark E 2 6 Tag and sensor configuration In order to setup the sensors that can be addressed it is required to configure the software Previously an inventory is necessary to find the desired tag After an inventory a tag is visible in the tag list Figure 1 Mark E A double click on this tag opens the Tag Sensor Configuration Window Figure 6 Tag2. 7 Od Seite 10 von 10
3. IPMS EVK UHF Z Fraunhofer IPMS RFID Reader Software User Guide IPMS EVK UHF RFID Reader Software User Guide Date 2015 07 17 Td Seite 1 von 10 IPMS EVK UHF Z Fraunhofer IPMS RFID Reader Software User Guide 1 Introduction 1 1 Abstract Fraunhofer IPMS has developed a battery less and wireless sensor system that s based on an UHF RFID transponder The transponder includes an internal temperature sensor and a programmable microcontroller and is able to interface several external sensors Using the standard ISO 18000 6c EPC C1G2 RFID protocol this system can be operated This document describes a GUI for simple measurements using commercial RFID readers 1 2 Table of Contents 1 MUN EON CO eesriie aniani EEEE RE TENERA 2 1 1 PS TEAC erriren TEELE aiii i 2 1 2 Table of OMG u u een eher 2 1 3 Minimum Requirements een ee nee 2 1 4 606 1 1 Te ee 3 2 COMENT oessa ieS E EE E 4 2 1 cress ce i ss cs see cca ei E 4 2 2 OUE east oases AA EA AES 4 2 3 Reader Connection Interface cuccaeneeseneeeesenensnsnnsnnnnnnnnnnnnnnnennnnennnnennenennn 5 2 4 Read ES I Seelen 7 2 5 IVO ee ee nee een rer 7 2 6 Tag 3008 Ns0r conii guration en eete 8 241 IM PT E E E 9 3 WROTE FENCES i A 10 1 3 Minimum Requirements IPMS_EVK_UHF reader software revision 74 Operating System Microsoft Windows 7 w th dot NET 2 0 installed USB or TCP LAN for the connection to the RFID reader Necessary files to support special RFID reader
4. Sensor Configuration On the Generals tab select the sensors which are available on the transponder and shall be used by measuring the specific tag The corresponding EPC is shown in the panel Tag Information on top To commit modifications click on the Apply button Now this window can be closed Specific setting can be made to internal and external sensors by selecting the corresponding tabs Tag Sensor Configuration Poo Tag Information EPC E03501030000060E 00000000 LMEASURE CMEASURE Sensors E intemal Temperature Sensor Module intemal Analog Digital Converter E extemal Bosch BMPO85 E extemal Sensirion SHT2 W etemal Texas Instruments TMP112 extemal Mems Vision MVH3000D0 F enable UIC instead of LMEASURE UIC Sensors E extemal Bosch BMP180 E extemal Bosch BME280 extemal Texas Instruments OPT3001 Status ready Figure 6 Tag Sensor Configuration with temperature sensor TMP112 activated After making changes in the tag sensor settings perform an inventory in order to activate the new configuration The next time this transponder is detected during an inventory the sensor settings will be retrieved automatically Date 2015 07 17 OO Seite 8 von 10 IPMS EVK UHF Z Fraunhofer IPMS RFID Reader Software User Guide IMPORTANT Only selected sensor are used for measurements Selected sensors that are not connected to
5. pter 1 3 in the application directory Enter the correct TCP IP address of the RFID device and a port if necessary Then select the corresponding interface and click the Connect button Reader Connection Pee Reader Connection Profile Profile TCP Metratec Pulsar MX TCP Metratec Pulsar MX Save Delete Save Delete C Interface Settings U Interface Settings 10 68 64 120 10 68 64 120 10001 10001 Metra Tec Metra Tec Connect Disconnect coss O Disconnect Close Firmware Firmware PULSAR_MX 01000213 Status ready to connect Status connect OF Figure 2 Reader Connection interface of MetraTec Pulsar MX RFID reader It is possible to reuse this configuration for further connections by entering a name in the top Profile textbox and click on the Save button Date 2015 07 17 POO Seite 5 von 10 IPMS EVK UHF Z Fraunhofer IPMS RFID Reader Software User Guide Once successfully established a connection with the RFID reader the firmware version is shown bottom in the Firmware box and the Connect buttons of this window and the main window are green Now this form can be closed Reader Connection Reader Connection a Profile Profile LAN Impinj SpeedwayR Korea LAN Impinj Speedway Korea Interface Settings IP Address 192 168 20 21 Fort Interface Impinj OctaneSDK 2 0 Firmware Fimware Version 4 83240 S
6. readers via USB connection are used download and install the corresponding USB drivers see chapter 3 2 Connect the RFID reader with the PC and power on the reader Wait until the boot sequence has succeeded and establish a connection via the Connect button Figure 1 Mark A The button will turn green if a connection with a RFID device is established see chapter 2 3 Date 2015 07 17 BO Seite 4 von 10 IPMS EVK UHF Z Fraunhofer IPMS RFID Reader Software User Guide 4 Position a RFID tag in front of the antenna of the RFID reader For an initial test a distance of 25cm 40cm will gain the best performance The distance can be adjusted by observing the RSSI value later only if supported 5 Select a task to run inventories Figure 1 Mark B left drop down menu see chapter 2 5 and click the Start Task button Figure 1 Mark B right If one RFID tag has been found the EPC s visible in the tag list Figure 1 Mark E Note Unknown sensor tags needs to be configured now see chapter 2 6 6 Select a task to run measurements Figure 1 Mark B left drop down menu see chapter 2 7 and click the Start Task button Figure 1 Mark B right Depending on the task you have chosen values will appear in the readout section Figure 1 Mark C 2 3 Reader Connection Interface Actually Impinj Deister and MetraTec RFID readers are supported by this software provided that the corresponding DLL files are present see cha
7. s and features are e MetraTec Pulsar MX extra files are not required e Deister RFID readers deBus dll v1 4 9 0 e Impinj SpeedwayR 420 Impinj OctaneSdk dll v2 0 0 5 LLRP dll v10 16 0 240 LLRP Impinj dll v10 16 0 240 e SkyeTek Supernova stapiclr dll v2 0 0 111 e ZedGraph chart readouts ZedGraph dil v4 5 9 41518 Date 2015 07 17 a Seite 2 von 10 IPMS EVK UHF Z Fraunhofer IPMS RFID Reader Software User Guide 1 4 Contact Hans J rgen Holland Fraunhofer Institute for Photonic Microsystems IPMS Maria Reiche Str 2 01109 Dresden Phone 49 351 8823 215 Fax 49 351 8823 266 http www rfid sensor plattform de http www ipms fraunhofer de de applications wireless systems rfid html Date 2015 07 17 Td Seite 3 von 10 IPMS EVK UHF Z Fraunhofer IPMS RFID Reader Software User Guide 2 Content 2 1 Overview Debug Help Model Speedway R420 Ta Fraunhofer Firmware Version 4 3 3 240 IPMS BMPO85 BMF coefs IPMS SAR SHT21 TMPII2 f RSS InvCnt Templint TempExt Pressure Humidity E03501010000110E00000000 23 42 TMP112 Figure 1 Main window of IPMS_EVK_UHF reader software A Reader connection section and reader communication indicator B Task selection with start stop button C Information and measurements serial number sensor value D Status flags of activities and communications with sensors E Tag list and readout for statistics 2 2 Quick Start 1 If MetraTec or Deister RFID
8. tatus ready to connect i Status connect OK Reader Connection Profile COM1 SkyeTec Nova Interface Settings SkyeTek stapiclr DLL nterface SkyeTek stapiclr OLL a come are Nova 0019 HW O0000001 SW 01010038 Figure 4 Reader Connection interface of SkyeTek Supernova RFID reader Date 2015 07 17 a Seite 6 von 10 IPMS EVK UHF Z Fraunhofer IPMS RFID Reader Software User Guide NOTE If the connection fails the Connect button is red and a status message is shown in the status line Please verify the power of the RFID reader the USB or network connection firewall settings of pc and gateways and try it again 2 4 Reader Settings If a TCP network connection is used the web interface is accessible by entering the IP address of the reader into a web browser Furthermore all vendors offers special software to configure their device see chapter 3 Every RFID reader supports different features Some of them are accessible directly from the IPMS EVK UHF reader software via Menu Settings gt Reader Operations The window is only available if a connection is established and the content depends on the used reader interface The window with settings of MetraTec PulsarMX Impinj SpeedwayR 420 and SkyeTek Super Nova RFID readers are shown at Figure 4 Deister RFID readers are supported too RN Impinj Reader Settings MetraTec Reader Settings Reader operations RF Reset ms 2000 Port
9. the RFID tag will result in errors 2 7 Measuring Once a tag was found chapter 2 5 and the desired sensors were configured chapter 2 6 the RFID sensor tag can be used for measurements by selecting an appropriate task and executing the Start Task button Figure 1 mark B It is possible to observe the communication to read a special sensor at the Protocol window Menu Windows gt Protocol Further information about using commands for communication with the internal microcontroller and measuring tags can be found in Smart ISO 18000 6C Sensor Tag 2 Date 2015 07 17 EEE Seite 9 von 10 IPMS EVK UHF Z Fraunhofer IPMS RFID Reader Software User Guide 3 References 1 ISO IEC 18000 6C Specification Gen 2 EPC Protocol 2 Fraunhofer IPMS RFID sensor tag document Smart ISO 18000 6C Sensor Tag http www fid sensor plattform de en download html 3 MetraTec RFID device support UHF Protocol Guide rl 13 MetraTec http www metratec com en support downloads html 4 Deister RFID device support deBus Protocol v1 38 Deister http en deister com contact 5 Impinj SpeedwayR 420 RFID device support Octane SDK Impinj https support impinj com he en us 6 SkyeTek Supernova RFID device support Sykeware V4 and Protocol V3 SkyeTek https skyetek zendesk com forums 7 ZedGraph l brary C class library authors jchampion kooseefoo rjosulli http sourceforge net projects zedgraph Date 2015 07 1
Download Pdf Manuals
Related Search