Wagner 0529017 Installation Guide
Contents
1. Problem C Spray pattern too thick runs and sags Problem D Spray jet pulsates Problem E Too much overspray Problem F Pattern is very light and splotchy Nozzle clogged Suction tube clogged Material flow setting too low Suction tube loose Air vent on suction tube blocked No pressure build up in container Air valve tube disconnected Air filter clogged Spray material too thick Nozzle loose Nozzle worn Nozzle seal missing or worn Material build up on air cap and nozzle Material flow setting too high 2 Air power setting too low Applying too much material Nozzle clogged Air filter clogged Too little pressure build up in container Spray material too thick Material in container running out Air filter clogged Air valve tube disconnected Gun too far from spray object Air power setting too high Moving the spray gun too fast Material flow setting too low Air power setting too high Note Only thin the material as a last resort to improve spray performance Optimal spray performance should be acheived simply by adjusting the various controls on the unit This unit contains no servicable electrical parts Do not attempt to service yourself Store indoors with the cord wrapped around the turbine handle having problems In the United States to speak to a customer service representative call our Technical Service2. at 1 800 328 8251 See www wagnerspraytech com in the C Have you tried the recommendations above and are still Contact Us section for Technical Service hours Clean Clean Increase material flow setting Remove and replace as tightly as possible Clean see page 15 Tighten container Reconnect both ends of the air tube Change Thin Tighten Replace Replace extras provided Clean Decrease material flow setting Increase air power setting Adjust material flow or increase movement of spray gun Clean Change Tighten container Thin 1 Refill Change Reconnect both ends of the air tube 1 Reduce distance 6 8 is ideal Decreasae air power setting Adjust material flow or de crease movement of spray gun Increase material flow setting Decrease air power setting Wagner Spray Tech All Rights Reserved
3. To Reassemble 1 Install the nozzle seal 1 with the groove a slot facing toward the nozzle away from the front end assembly 2 Insert the nozzle 2 Make sure to align the groove b and notch c and align the nozzle opening with the needle 3 Put the air screen d in the air cap e Put both 3 on the nozzle 2 and secure with the connecting nut 4 Note This step is easier if the spray gun is facing up 4 Snap the adjustment ring 5 into the connecting nut 4 enabling the adjustment lever f on the peg g to be positioned in the air cap Note Make sure that the two recesses on the adjustment ring are engaged in the air cap tabs 5 Reassemble the spray gun Note Make sure the air valve tube is free of paint If not clean the air valve tube by following the instructions on the next page If clean make sure it is attached securely at both ends see inset Nozzle seal DO NOT LOSE It is important that the nozzle seal inside the nozzle be re installed properly Make sure the cup side of the seal the side with the groove is facing out towards the front of the nozzle Improper installation will cause leakage AN WN y 14 Wagner Spray Tech All Rights Reserved Cleaning the Filters IMPORTANT Before every use you should inspect the air filter in the turbine to see if it is excessively dirty If it is dirty follow these steps to replace i
4. t IMPORTANT Never operate your unit without the air filter Dirt could be sucked in and interfere with the function of the unit 1 2 Press the tabs on the side of the turbine to remove the filter cover Remove the dirty filter from the turbine and replace with a new one The smooth side of the air filter must be placed toward the turbine Secure the cover back onto the turbine Cleaning the Air Valve Tube Note If paint has entered the air tube proceed as follows 1 IMPORTANT The air tube and valve seal c are only solvent resistant to a limited extent Do not immerse Pull the air tube a at the top from the spray gun Screw off the valve cover b Remove the valve seal c Clean all the parts carefully in solvent only wipe 2 Place the valve seal c in the valve cover b with the Note Installing the valve seal into the valve cover will pin facing into the tube be much easier if the valve cover is inverted 3 Turn the spray gun upside down and screw on the valve cover with valve seal inside from underneath Note Turning the spray gun upside down will prevent the valve seal from falling out of the valve cover during reinstallation 4 Place the air tube on the valve cover and on the nipple at the spray gun oS Wagner Spray Tech All Rights Reserved Troubleshootinc Problem A Little or no material flow Problem B Material leaking
Download Pdf Manuals
Related Search