WingIts GBW40 Installation Guide
Contents
1. innovations Commercial PART GBW40 The World s Strongest Fastener Exceeds ADA Guidelines and ALL Building Codes on Eliminates the need for Blocking WATERPROOF Rated up to 1000 lbs in drywall with tile Compatible with Winglts Grab Bars MADE WITH PRIDE IN THE U S A z OVER TWO MILLION Sa 210 0 0 7 INSTALLED AA APACHE20 AS EASY AS 1 1 4 DRILL BIT Call us at 877 894 6448 Visit us at www wingits com Email us at sales wingits com Winglts HE SOLUTIONS COMPANY GOMMERCIAL GRAB BAR FASTENING SYSTEM INSTALLATION GUIDE WINGITS GRAB BAR FASTENING SYSTEMS EXCEED BUILDING CODES FOR GRAB BARS IN THE FOLLOWING WALL SUBSTRATES 9 8 drywall painted or wallpapered 4 2 or 5 8 drywall with tub surrounds 4 2 or 5 8 drywall with tile marble and all stone 1 2 or 5 8 drywall with any panel types including fiberglass faux marble acrylic and plastics Multiple layers of drywall Plaster and lathe 1 4 acrylic fiberglass tub surrounds Most wall panels All masonry type boards with or without decorative panels NEVER INSTALL ANY FASTENER INTO WET OR DETERIORATING WALLS STRUCTURAL BLOCKING MUST BE USED IN PLAIN 1 2 DRYWALL when attempting to meet commercial building codes MAKE SURE YOU HAVE THE RIGHT SIZE Winglt gt GBW40 Standard Winglt is used in walls framed with 2 X 4 s 3 1 2 hollow or larger gt SRGBW40 Reve2. e 3M WATERPROOF ADHESIVE on the Winglts 2 Back out the center screw about the same distance as the wall thickness 3 Insert the Grab Bar Winglts into the wall with the holes aligned vertically 12 amp 6 o clock Hold down firmly allowing the adhesive to stick 5 Push the screw head to the faceplate to pop the WINGS behind the wall optionally hit the screw head with a mallet to eject the WINGS 6 Pull on the screw head and tighten the screw 7 Attach the Grab Bar with the supplied 10 32X3 16 s s screws Winglts 18 8 Stainless Steel Grab Bar MOUNT WITH 2 SCREWS TOP amp BOTTOM With NON Winglts Grab Bars Confirm the Bar s compatibility with Winglts 877 894 4466 The Winglts must be assembled to the Grab Bar PRIOR to inserting into the wall as the installation must be more precise The FACEPLATE hole alignment to the grab bar flange hole MUST be exact Temporarily attach the Winglts to the Grab Bar Remove the liner from the 3M WATERPROOF ADHESIVE on the Winglts Insert the Winglts using the Grab Bar as a template Push on Grab Bar for 1 2 a minute to adhere Winglts to the wall Remove Grab Bar Activate and tighten the Winglts as stated in Steps 2 9 above Wingit Innovations LLC 714 5th Avenue Bradley Beach NJ 07720 Toll Free 877 894 6448 Fax 732 869 9474 E mail sales wingits com Website www wingits com
3. rse Winglt is used in walls framed with 2 X 3 s 2 1 2 hollow or larger gt Winglts come standard with a Stainless steel 4 machine screw for walls up to 1 1 4 thick Longer Screws Available for thicker walls CALL FOR CUSTOM PRODUCTS 877 894 6448 FOR MAXIMUM SAFETY AND TO MEET ADA REQUIREMENTS GRAB BARS SHOULD BE INSTALLED HORIZONTALLY 33 36 INCHES FROM THE FLOOR LOCATION To ensure adequate clearance a stud finder should be used to verify there are no studs within the area where the Wingit will be installed Once inserted each wing assembly will spring open almost 3 in diameter Tools Required Screwdriver 1 25 Drill Jur APACHE 200 rated 200 holes in ceramic wall tile Before you install Verify the length of the grab bar by measuring from the inside of one flange to the outside of the other Continued Make sure that there is at least 1 5 away from the edge of the stud f concerned drill a pilot hole and insert a piece of wire in the shape of an L twirl the wire to make sure that there is nothing in the way Drill a 1 1 4 hole in the wall precisely at the center point where each grab bar flange will align Clean wall surface Installing with Grab Bars from Winglts 12 oclock 3M WATERPROOF 6 o clock TAPE LINER Winglts Grab Bar Flanges have 3 holes and TWO SLOTS in each flange Use the TWO SLOTS to attach the grab bar to FACEPLATE 1 Remove the liner from th
Download Pdf Manuals
Related Search