Knaack 40 Instructions / Assembly
Contents
1. the following patents or trademarks U S 5076078 1182980 1182981 1182982 1182983 1517767 1560477 1897535 945736 Canada 280058 283281 281398 U K 2233036 13890299 Aus 754070 754069 N Z 296048 296050 other patents pending KNAACK MANUFACTURING COMPANY 420 E TERRA COTTA AVENUE CRYSTAL LAKE ILLINOIS 60014 815 459 6020 2000 Knaack Manufacturing Company KNAACK MANUFACTURING COMPANY2. the locking levers located inside the track that is attached to the drawer Lift the left lever A A 2 5 16 18 x 3 4 Carriage Bolt P Q ej 1 4 4 Pushnut O g 1 5 16 18 L Whiz Nut S Figure 3 Caster Mounting while pressing down on the right lever B Pull drawer clear on the slides Drawer installation 4 When right and left slides are in place extend fully Next push rear pocket on drawer onto rear clip on A CAUTION Pull out only one drawer at a time to avoid sudden tipping of product which could cause serious personal injury or property damage 5 Take one slide and insert rear clip into rear notch and lower front clip into front notch See Figure 5 Figure 4 Upper Drawer Removal Drawer Slide Removal 6 Reverse step slide and lower front pocket onto front clip Close the drawer com pletely The mechanism will auto matically latch Drawer Slide Installation FRONT VIEW Figure 5 Drawer Slide Installation DRAWER CABINET MEMBER MEMBER SIDE VIEW FRONT REAR CABINET MEMBER NOTICE Any modification or unintended use of this product shall immediately void all manufacturers warranties Manufacturer disclaims all liability for injuries to persons or property resulting from any modification to or unintended use of this product If you have any questions please give us a call Call Toll Free 1 800 456 7865 Knaack products are protected by one or more of
3. ASSEMBLY AND INSTALLATION INSTRUCTIONS JOBMASTER Rolling Work Bench Models 40 amp 44 Hole Plugs me Push Handle 5 16 18x 3 4 Truss Hd Bolt 5 16 18 x 3 4 Truss Head Bolt gt lt DoorHandle IMPORTANT BEFORE YOU BEGIN Read these instructions and warnings completely before installation CASTER BOLT KIT Bolt kit 32 0001 is provided with your RWB Check this bolt kitto be sure the following parts are included Quan Description 16 5 16 18X3 4 Carriage Bolt 16 5 16 18WhizLock Nut 16 1 4 Pushnut HANDLE LIFT KNOB KIT Push Handle Door Handles 5 16 18 x 3 4 Bolt Truss hd 5 16 18 Hex Whiz Nut LiffKnob Hole Plugs NMPO BRON i PARTS LIST Work Bench Cabinet Caster Set with bolt kit Handle kit 5 16 18 Whiz Lock Nut Figure 1 Assembly View A WARNING Black knob must be latched in the closed position when moving this product so doors and drawers do not open on inclines which can cause serious personal injury or property damage TOOLS REQUIRED 1 2 Open or Box End Wrench 1 2 Socket 3 8 drive 3 8 Medium Extension 3 8 Ratchet Wrench Screwdriver common ASSEMBLY INSTRUCTIONS 1 Remove the caster box handles and bolt kit from the cabinet At tach the Door Handles Figure 1 Insert Hole Plugs in the Push Handle and attach to the end WATCHMAN III Lock System IMPORTANT Carefully follow the separat
4. e in structions see inside door which will guide you to a proper lock installation A DANGER e Do not put fuels flammables explosives or hazardous materials inside these products e Gasoline solvents gun powder or other munitions dynamite propane acetylene or other such products can explode if stored inside these products e Use these products ONLY for storing and transporting electric or hand tools and equipment and other similar materials e Failure to follow these warnings or modification or other uses of these products could result in death serious injury or property damage CAUTION Caster Brakes are not suitable for keeping units in place when transporting Secure by another method Do not use casters on rough or uneven surfaces Do not tow caster mounted boxes Caster Set Installation 2 Close the doors and lay the cabinet on its back onto the flat tened shipping carton to prevent paint scratches Figure 2 Mount the Swivel Casters on end you mounted the Push Handle Insert a Carriage Bolt into a mounting hole and push a Pushnut onto the bolt to hold it in place Fig ure 3 Repeat this for the other three mounting bolts Place the Caster over the bolts then fasten Rev F 11 00 Part No 14 4044 Figure 2 Caster Mounting Holes with Whiz Nuts Repeat this for the remaining Casters Drawer Removal 3 To remove a drawer Figure 4 pull the drawer out until it stops Notice
Download Pdf Manuals
Related Search