DreamLine SHEN-6134600-08 Installation Guide
Contents
1. 2 Please note that you should consult your local building codes with questions on installation compliance standards Building and plumbing codes may vary by location and DreamLine is not responsible for code compliance standards for your project and will not accept any returns 3 Please ensure that prior to the installation the installation surface is leveled and solid and will be able to support the total weight of the unit Also make sure the walls are at right angles Irregular installation surface level or improper angle of side walls will result in serious problems for your installation Please note that some adjustments and drilling might be necessary during the installation process 4 This unit has to be installed against a finished floor and walls 5 Please NOTE This door does not have out of plumb adjustment Make sure your walls are at right angles 6 This door requires a minimum 2 wide threshold base or installation space 7 Please note that Step 6 calls for installation of the door to the wall using anchors However the manufacturer strongly recommends installing these heavy doors to the studs or to preinstalled 2x6 wood reinforcements behind the wall and attach the Wall brackets to it Attention This enclosure is extremely heavy and requires professional installation Tools Required Tape Phillips Drill bit Drill bit Drill bit Caulk Measure Pencil Screwdriver 3 8 5 16 O 1 8 GZ X2. QREAMLINE ream in style ENIGMA X SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter modify or redesign products at any time without prior notice For the latest up to date technical drawings manuals or any other details please refer to the support BathAuthority com web page Please read these instructions carefully before installing If you have any questions regarding installation please call our technical support specialists Monday through Friday 9 00 AM 5 00 PM EST at Phone 1 866 731 2244 Fax 1 866 227 1533 or e mail our technical support group at support BathAuthority com For more information on DreamLine Shower Enclosures please visit www BathAuthority com Preparation 1 After opening all boxes and packages read this introduction carefully Check that all of the needed parts are included in the package by marking all the components on the Detailed Diagram of Shower Door Components Examine boxes and packages for shipping damage If the unit has been damaged has a finishing defect or has missing parts please contact our customer support department within 5 business days of the delivery date Please note that DreamLine will not replace any damaged products or missing parts free of charge after 5 business days or if the product has been installed Feel free to contact DreamLine if you have any questions
3. er m l ace wo i J y I Level Caulk Electric Gun Drill Hammer Miter saw or Hacksaw Enigma X Enclosure Rev 2 Ver 2 04 2013 2 Detailed Diagram of Shower Enclosure Components Packing List 01 Door stopper 2pcs 12 Guide block with plugs 1pc 02 Stationary glass 1pc 13 Bumper strip 1pc 03 Upper Guide rail 1pc 14 Anti water strip 2pcs 04 Roller 2pcs 15 Anti splash threshold 1pc 05 Glass door 1pc 16 Threshold bracket with plug 1pc 06 Handle 1pc 17 Round head screw ST4 2x25 4pcs 07 Glass bracket 2pcs 18 Round head screw ST4 2x55 3pcs 08 Guide rail bracket 2pcs 19 Wall bracket Apc 09a Wall anchor 3 8 1pc 20 Roller guard 2pcs 09b Wall anchor 5 16 3pcs 21 Glass Connector 1pc 10 Round head screw ST6x55 1pc 22 Return panel 1pc 11 Hex wrench 3mm 4mm 5mm 1set NOTE Unpack your unit carefully and inspect it Lay it out and identify all parts using parts diagram and part list in your manual as a reference Before discarding the carton check for small hardware bags that tend to fall to the bottom of the box If any parts are damaged or missing please contact DreamLine for replacement NOTE Retain these installation instructions for future reference Enigma X Enclosure Rev 2 Ver 2 04 2013 Enclosure matching Shower base assemble size drawing Sho
4. See Fig 15 for details 14 Place the Guide Block 12 on the shower base or the threshold and place the Stationary glass 02 back into the designated position so it gets in the groove of the Guide block Fasten the female part of the Guide rail bracket 08 to its male part on the wall Tighten the set screws on the Guide rail brackets to secure the Upper Guide rail between the wall and the Return Panel 22 Assemble the Wall bracket 19 at the bottom corner of the Stationary glass and tighten the bolt Put the level to the Upper Guide rail and use hex spanner wrench to adjust Guide rail bracket on the wall until the top rail is absolutely vertical Tighten the screws on both sides of the Guide rail bracket See Fig 16 for details Enigma X Enclosure Rev 2 Ver 2 04 2013 15 Put the level to the Upper Guide rail 03 and use hex spanner wrench to adjust Guide rail bracket 08 on the wall and adjust Glass connector 21 on the Return panel 22 until the top rail is absolutely vertical Tighten the screws on both sides of the Guide rail bracket See Fig 17 for details 16 Parallel the Stationary glass 02 to the 7 shower base or threshold Measure the 5 distance from the Return panel to the far edge of the Guide block 12 This distance will be X X Cut the Anti splash threshold to the siz
5. cleaning products that contain scoring agent because this may scratch the surface Never use bristle brushes or abrasive sponges To assure a long lasting finish wipe off the metal parts after each use with a soft cloth Do not use abrasive cleaners or cleaning products containing ammonia bleach or acid If accidentally used rinse the surface as soon as possible to prevent finish peeling or corrosion After cleaning the shiny finishes rinse thoroughly and wipe dry with soft cloth Clean stainless steel surfaces at least once a week When applying stainless steel cleaner or polish work with not across the grain Never use abrasive sponge or cloth steel wool or wired brushes Enigma X Enclosure Rev 2 Ver 2 04 2013 17 DREAMLINE EXCLUSIVE LIMITED WARRANTY AS OF MAY 6 2013 This warranty extends only to the original owner end user for household use only and is not transferable to a subsequent owner This warranty extends for a designated period of time so long as it remains in use in its original place of installation This warranty applies only to DreamLine products purchased from an authorized dealer in United States or Canada Proof of purchase original sales receipt from the original consumer purchase must be provided with all warranty claims IN NO EVENT SHALL THE LIABILITY OF DREAMLINE EXCEED THE PURCHASE PRICE OF THE UNIT DreamLine products must be installed by a fully insured and licensed professional Installation of Drea
6. the vertical edges of the Stationary glass 02 and the Glass door 05 Also press the Bumper strip 13 on the vertical edge of the Glass door Mount the Handle 06 to the Glass door Adjust both Door stoppers 01 to ensure that they are positioned upright and the door is in its maximum opening and closing range Tighten the set screw to fasten them in place See Fig 21 for details w I y Fig 21 20 Apply silicone at the both ends of the Anti splash threshold Gi 15 around the Guide block 12 and around the Threshold bracket 16 See Fig 22 for details OA ae Caulk 2 DA NS Caulk Fig 22 Enigma X Enclosure Rev 2 Ver 2 04 2013 21 Apply silicone along the connections of the Stationary glass and Return Panel with the wall and the shower base or threshold See Fig 23 for details Fig 22 Product Maintenance To insure long lasting life for your acrylic back walls wipe them off after each use with a soft cloth To clean the acrylic back walls use non abrasive sprays or cream based cleaners Never use abrasive cleansers metal brushes or scrapers that could scratch or dull the surface To insure long lasting life for your glass shower products wipe them off after each use with a soft cloth Rinse and wipe of the glass using either soft cloth or squeegee to prevent soap buildup Never use abrasive cleaners and
7. ON OR FOR ANY DIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGE LOSS OF USE LOSS OF TIME LOSS OF PROFITS INCONVENIENCE INCIDENTAL EXPENSES LABOR OR MATERIAL CHARGES OR ANY OTHER COSTS RESULTING FROM THE USE OF ITS PRODUCTS OR PERTAINING TO THE APPLICATION OF THE PRESENT WARRANTY OR RESULTING FROM THE REMOVAL OR REPLACEMENT OF ANY PRODUCT OR ELEMENT OR PART COVERED BY THIS WARRANTY PRODUCT WARRANTY PERIODS DreamLine is not responsible for product code compliance or for verifying building code restrictions on installation or use and any such compliance is excluded from this warranty DreamLine reserves the right to modify this warranty at any time such warranty modifications will not alter the warranty applicable at the time of sale of the products in question The warranty terms for specific products for consumer non industrial non commercial non business use only are SHOWER BACKWALL SHOWER CABINS JETTED amp STEAM DreamLine warrants shower backwalls and shower cabins to be free from defects in workmanship for a period of one 1 year from initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER amp TUB DOORS SHOWER ENCLOSURES DreamLine warrants shower doors tub doors and shower enclosures to be free from defects in workmanship and materials under normal residential use for a period of five 5 years from the initial date of purchase by the owner end user contractor or builder from an
8. authorized dealer Warranty for plastic strips shall be limited to one 1 year Warranty for any part in Oil Rubbed Bronze finish shall be limited to one 1 year SHOWER BASES DreamLine warrants shower bases to be free from defects in workmanship and materials under normal residential use for as long as the original consumer purchaser owns their home in which their product is installed SHOWER COLUMNS DreamLine warrants shower columns to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer SHOWER SEATS DreamLine warrants shower seats to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer Warranty shall be VOID if the shower seat is not professionally installed on a properly reinforced wall VANITIES AND VESSEL SINKS DreamLine warrants bathroom vanities and vessel sinks to be free from defects in workmanship and materials under normal residential use for a period of one 1 year from the initial date of purchase by the owner end user contractor or builder from an authorized dealer STATE LAWS AND THIS WARRANTY Some states provinces do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of spec
9. e of a x 2 Insert one side of the Anti splash threshold fully into the Guide block and cover the other SSN side with the Threshold bracket 16 SA x Parallel the Anti splash threshold to the Nf yc front edge of the shower base or threshold AA px and mark drilling hole for the Threshold I bracket M172 See Fig 18 for details Fig 18 Enigma X Enclosure Rev 2 Ver 2 04 2013 17 Drill the holes for the Guide 1 block and the Threshold K bracket using 1 8 drill bit In 1 8 Apply silicone to the bottom of za the Anti splash threshold and place it back into designated position Fasten the Guide block and the Threshold 2 bracket to the shower base or threshold with the Round head screw ST4 2x25 17 Cover holes with the provided decorative plugs 1 8 See Fig 19 for details 18 Attach two Rollers 04 to the Glass door 05 Suspend the door by hanging the Rollers onto the Upper guide rail 03 and slide the bottom edge of the Glass door into the groove of the Guide block 12 Adjust the fasteners on both rollers to ensure that the bottom edge of the glass door does not touch the bottom of the guide block Then mount two Roller guards 20 on the door to secure the door to the Upper guide rail See Fig 20 for details PRY Enigma X Enclosure Rev 2 Ver 2 04 2013 19 Press the Anti water strip 14 on
10. eturn panel 22 Slightly tighten the set screws Please note that the Upper Guide rail secured on the Stationary Glass should face inside the shower See Fig 12 for details Fig 12 Enigma X Enclosure Rev 2 Ver 2 04 2013 11 Make sure the Stationary glass 02 and the Upper Guide rail 03 are leveled and aligned with the shower base or the threshold If a horizontal adjustment is os Om required adjust it in the Glass brackets 8 l 07 i See Fig 13 for details 4 12 Outline the position of the Wall bracket 19 and the Guide Rail bracket 08 on the wall Set the Stationary glass 02 aside Remove the Wall bracket from the Stationary glass and the Guide Rail bracket from the Upper Guide Rail 03 and by placing them back to the outlined positions mark the drilling holes on the wall See fig 14 for details Fig 14 Enigma X Enclosure Rev 2 Ver 2 04 2013 13 Drill the holes using 5 16 drill bit and insert the Wall anchors 9b for the Wall bracket 19 Drill the holes for the Rail brackets 08 using 3 8 drill bit and insert the Wall anchors 9a Mount the Wall bracket to the wall using the Round head screw ST4 2x55 18 Mount the male parts of the Rail bracket onto the wall using the Round head screw ST6x55 10
11. g but not limited to the implied warranties of merchantability and fitness for a particular purpose WARRANTY TERMS DreamLine will at its election repair or replace the product found by DreamLine in its sole judgment to be defective within the warranty period under normal residential use and maintenance The replacement of a product is limited to supplying a replacement product or part same as existing or if not available comparable product DreamLine warranty obligation shall be discharged upon tender of parts replacement or repair of the product Purchaser s refusal to accept the tender terminates all warranty obligations and VOIDS THE WARRANTY Cost of freight for returning products to DreamLine for repairs or replacement under this limited warranty are the responsibility of the customer Cost of freight associated with shipping of replacement product or parts to the customer may be charged to customer Any product replaced or repaired during the warranty period will be covered only for the remaining period of the original warranty In no event will DreamLine be liable for costs of repair or replacement of any installation material including but not limited to tiles marble etc DREAMLINE IS NOT RESPONSIBLE FOR INSTALLATION REMOVAL OR REINSTALLATION COSTS OF ANY PRODUCT REQUIRING WARRANTY SERVICES Any modification or alteration of any DreamLine products will void the warranty DreamLine product installations and repairs must be performed by eithe
12. ial incidental or consequential damages so these limitations and exclusions may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state province to state province WARRANTY SERVICE The following information will be required for you to file a Warranty claim 1 Your name address and telephone number 2 Product model number 3 Brief description of problem please note that additional information such a photos may be required to fully process your warranty claim 4 Proof of purchase You may submit this information by e mail mail or fax to DreamLine Warranty Service Center 75 Hawk Road Warminster PA 18974 F 1 866 857 3638 T 1 866 731 2244 Warranty bathauthority com REAMLINE dream in style TEL 866 731 2244 FAX 866 227 1533 WWW BATHAUTHORITY COM For more information on DreamLine Shower Enclosures please visit www BathAuthority com
13. mLine product by anyone other than fully insured licensed professionals shall VOID THE WARRANTY DreamLine recommends that such licensed professionals have experience in the installation of bathroom products Installation of certain products including without limitation glass products i e shower and tub doors by an inexperienced installer may result in glass breakage and consequently cause personal injury or death PARTS ONLY WARRANTY This warranty is extensive in that it covers replacement of all defects LABOR CHARGES AND OR DAMAGE INCURRED IN INSTALLATION REPAIR OR REPLACEMENT AS WELL AS ANY OTHER KIND OF LOSS OR DAMAGE ARE EXCLUDED COMMERCIAL USE AND OTHER EXCLUSIONS This warranty excludes all industrial commercial and business usage whose purchasers are hereby extended a one 1 year limited warranty from the date of purchase for shower and tub doors a three 3 month limited warranty from the date of purchase for vanities and sinks with all other terms of this warranty applying except the duration of the warranty DREAMLINE JETTED AND STEAM SHOWER CABINS DREAMLINE SHOWER COLUMNS AND DREAMLINE SHOWER SEATS ARE NOT INTENDED FOR COMMERCIAL USE AND THERE IS NO WARRANTY EXTENDED FOR THESE PRODUCTS FOR COMMERCIAL USE DreamLine hereby disclaims all warranties for products sold as dealer or store displays DreamLine hereby disclaims all warranties for products used outside of the United States or Canada whether expressed or implied includin
14. on the wall and the shower base or threshold Set the Return panel 22 aside Remove the Wall bracket from the Stationary glass and by placing it back to the outlined position mark the drilling holes on the wall See Fig 5 for details 2 4 Fig 5 1 4 5 Drill the holes in the wall using 5 16 drill bit and insert the Wall anchors 9b for the i 1 3 Wall bracket 19 Mount the Wall bracket Sgi 5 16 to the wall using the Round head screw C ST4 2x55 18 i Drill the hole in the shower base or threshold using 1 8 drill bit and mount the Wall 2 5 il bracket 19 using the Round head screw ST4 2x25 17 T See Fig 6 for details Fig 6 Enigma X Enclosure Rev 2 Ver 2 04 2013 6 Place the Return Panel 22 back in the designated position and assemble the Wall brackets 19 See Fig 7 for details 7 Measure the distance between the finished wall and the internal side of the Return Panel 22 This distance is marked as W See Fig 8 for details Fig 7 Enigma X Enclosure Rev 2 Ver 2 04 2013 8 Your Upper Guide rail 03 has been precut for your Shower model opening width 48 or 60 for shower width If W width of your opening between finished wall and the internal side of the Return Panel 22 is equal to the size of your Shower model it is unnecessary to cut the Uppe
15. r Guide rail and you can continue to Step 9 If W width of your opening between finished wall and the internal side of the Return Panel 22 is less than the size of your Shower model you will need to cut the Upper Guide rail from the end which is farther from the Glass brackets 07 holes The length to cut off will be L L Subtract W from the size of your Shower model FOR EXAMPLE If your wall to glass panel opening W 58 Your shower model is 60 L 60 58 2 You have to cut 2 off from the rail See Fig 9 for details Install the Upper guide rail 03 to the Stationary glass 02 with the Glass brackets 07 and tighten the set screws Slide the Door stoppers 01 on each end of the Upper guide rail and secure them temporarily Slide the Guide Rail brackets 08 on each end of the Upper guide rail and temporarily secure them as well Assemble the Wall Bracket 19 to the bottom corner of the Stationary glass 02 See Fig 10 and Fig 11 for details SS ej Fig 9 2 l 4 d l ee Fig 10 Enigma X Enclosure Rev 2 Ver 2 04 2013 NOTE Before you install the Stationary glass 02 you have to take the Glass door 05 into the shower room and lean it against the wall 10 Place the Stationary glass 02 on the preinstalled shower base or threshold and butt it up against the wall Temporarily fasten the Upper Guide Rail 03 to the R
16. r a DreamLine authorized agent or a licensed insured and experienced professional contractor installation or repairs performed by any other party shall void the warranty This warranty shall not apply to breakage or damages caused by normal wear and tear fault carelessness abuse misuse misapplication improper maintenance alteration or modification of the unit as well as chemical or natural corrosion accident fire flood act of God or any other casualty Improper care and cleaning will void the warranty Use of cleaners containing abrasive cleansers ammonia bleach acids waxes alcohol solvents or other products not recommended for chrome or similar finish glass or acrylic will void the warranty For additional product maintenance instructions please refer to product installation manual DreamLine is not responsible for any issues arising in connection with errors or omissions in information provided on DreamLine s websites The warranty does not extend to any non DreamLine plumbing or components installed by installers end users or by any party other than DreamLine THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE BATH AUTHORITY LLC DREAMLINE AND OR SELLER DISCLAIMS ALL LIABILITY FOR SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES DREAMLINE IS NOT LIABLE FOR PERSONAL INJURIES OR DEATH TO ANY PERS
17. wer Base DLT 1034481 2 32 1 2 825mm 46 1 2 1182mm Shower Base DLT 1036601 2 34 1 2 877mm 58 1 2 1487mm rr NOTE To match the shower base you have to cut 2 off from the Upper Guide rail 03 Enigma X Enclosure Rev 2 Ver 2 04 2013 Enclosure matching threshold assemble size drawing 32 1 2 825mm 48 1 2 1229mm 34 1 2 877mm 60 1 2 1534mm SSS Enigma X Enclosure Rev 2 Ver 2 04 2013 See Fig 1 for details 2 Attach the Wall brackets 19 to the Return panel 22 Bolted side of the Wall brackets has to face inside the shower See Fig 2 and Fig 3 for details 1 This unit requires a minimum 23 4 wide threshold shower base or installation space Shower Enclosure Installation Fig 2 Enigma X Enclosure Rev 2 Ver 2 04 2013 Fig 3 3 Place the Return panel 22 on the preinstalled shower base or threshold Butt it up against the wall and level it vertically Make sure the Return panel is aligned with the shower base or the threshold See the Shower Enclosure Plan for the dimensions Some trimming may be required See Fig 4 for details Enigma X Enclosure Rev 2 Ver 2 04 2013 4 Outline the position of the Wall 1 3 brackets 19
Download Pdf Manuals
Related Search