PULSE Showerspas 1032 Installation Guide
Contents
1. PULSE SHOWERSPAS Hanalei Showerspa Model 1032 Installation Instructions oo OO o Hanalei ShowerSpa Model 1032 Please Read The Following Instructions COMPLETELY Before Beginning Our goal is to ensure your installation goes smoothly and safely Please read these instruc tions carefully and follow recommendations for plumbing and mounting After reading instructions if you determine you do not have the necessary skills and or tools we recommend that a licensed plumbing contractor complete the installation If you encounter any problems during installation CALL TECHNICAL SUPPORT TOLL FREE at 888 785 7320 Before returning your ShowerSpa to the store You Will Need The Following Tools Soft pencil or felt pen to mark tile Reciprocating saw w metal cutting blade Sawzall Safety glasses Channel locks or adjustable wrench Tape measure Drill preferably cordless Level Va Masonry drill bit Qi k Stub Out Location ESTIMATED MOUNTING HEIGHT AND STUB OUT LOCATION FOR INDIVIDUALS 5 8 6 2 7254 4 42 304 i ce A 90 Fittings Not Included A 4 a 35 Mark bottom of La ShowerSpa Parts Legend Handheld Shower Handheld Holder Handheld Hose Handheld Outlet Handheld Outlet Hose Large Rubber Washer 2 ShowerSpa Shower Head Shower Arm Escutcheon2. Shower Arm Outlet Shower Arm Outlet Hose 13 12 G O Front Back Figure 1 DO Oz 8 Back of ShowerSpa 7 ESS 9 Figure 2 o Brass Nut Mounting Screw Nylon Anchor Mount Bracket Rubber Washer 1 extra Diverter Knob Thermostatic Valve After unpacking your ShowerSpa some assembly is required prior to installation Shower Arm Assembly figure 1 1 Place the escutcheon 4 over the threaded end of the shower arm 3 and insert threaded end into shower arm outlet 5 Make certain the threads for attaching the shower head are pointing down 2 On the inside of the ShowerSpa place the large rubber washer 12 over the threaded end and tighten securely with brass nut 13 DO NOT OVERTIGHTEN 3 Put a rubber washer 17 into the shower arm outlet hose 6 and then tighten to the shower arm 3 Be sure to check for leaks before completing installation Handheld Holder Assembly figure 2 1 Place the threaded end of the handheld holder 8 into the handheld outlet 10 Make certain the threads for the handheld hose are pointing down 2 On the inside of the ShowerSpa place the large rubber washer 12 over the threaded end and tighten securely with brass nut 13 3 Put a rubber washer 17 into the handheld outlet hose 11 and then tighten to the handheld holder 3 Be sure to check for leak
3. NOT SEAL BOTTOM 4 Additional fittings or longer supply lines may be necessary depending on your specific situation 2 The mounting height can vary depending on several factors i e location of supply lines old valve access area interference from ShowerSpa plumbing personal preference etc perature Once you set the knob to the desired operating temperature the thermostatic mixing valve will regulate the temperature keeping it constant even when water pressure drops inside the plumbing lines i e someone flushes a toilet etc Spa after each use Allowing water to evaporate on the surface can lead to a buildup of mineral deposits Cleaning with a damp nonabrasive sponge and drying with a clean soft cloth should help keep your ShowerSpa looking beautiful REMEMBER NEVER use any abrasives or harsh cleaners Clean with mild soap and water ONLY To keep your ShowerSpa in pristine condition DRY AFTER EACH USE N Manufacturer s Limited Warran PULSE Shower Spas Inc warrants that all ShowerSpas are free from defect in workmanship and or materials for a period of three years from the date of purchase This warranty extends to the original purchaser only and is non transferable This warranty does not cover and PULSE ShowerSpas will not pay for any conditions malfunctions or damages resulting from 1 normal wear and tear improper installation whether performed by a contractor a service company or the consumer impro
4. is a Before drilling holes for the brackets make certain the Spa allow the water to reach operating temperature before entering the shower gate valve where the water main enters the house Turning Showerspa will rest flat against finished wall surface at the the water valve off at hot water tank does not turn off cold desired mounting height with the supply lines connected Br Di rter water supply line IRA ass Diverte 9 Drill a holes through wall surface using a masonry bit Drill i s Ec Les The brass diverter is used to turn vvater on and off as vvell as change betvveen functions Simply rotate the Make certain that water is completely turned off to both the slowly through wall surface to avoid cracking and chipping Sn I i diverter knob either direction to select the desired function off shower head handheld shower body hot amp cold supply lines of the shower Turn shower valve on Insert anchors and securely screw brackets to wall Before ake or tubspout Tota the Showerspa ott simply rotate thediverterso the knob is p intind straight both hot and cold to verify water supply is OFF Open a sink connecting hot and cold supply lines hang the ShowerSpa e ae th thermostatic mixin Sa at i iempenatre P 9 9 faucet in the bathroom in which you are installing the Show on wall check the height and make sure the ShowerSpa is 9 9 p I erSpa to relieve any pressure and help adequately drain the flush against the vvall vvith a se
5. b For a person 5 8 6 2 tall we recom mend placing the holes of the upper bracket at 72 from finished floor height From the upper bracket holes measure down 42 for location of the lower bracket holes Showerspa will rest flat against finished wall surface at the desired mounting height with the supply lines connected Drill 4 holes through wall surface using a masonry bit Drill slowly through wall surface to avoid cracking and chipping Insert anchors and securely screw brackets to wall Before connecting hot and cold supply lines hang ShowerSpa on wall check the height and make sure ShowerSpa is flush against wall with a secure fit Connect hot and cold water supply lines to stub outs DO NOT OVERTIGHTEN Before mounting the ShowerSpa check fittings to make sure they are secure Turn on water and check for leaks When fittings are leak free mount ShowerSpa on wall OPTIONAL Seal around body of ShowerSpa with a bead of silicone DO NOT SEAL BOTTOM 1 Additional fittings or longer supply lines may be necessary depending on your specific situation 2 The desired mounting height of ShowerSpa determines height of the Y2 stub outs The stub outs must be located at a height allowing supply lines to be connected and body of ShowerSpa to rest flat against finished wall 3 The mounting height may vary depending on several factors i e location of supply lines interference from ShowerSpa plumbing personal pre
6. cals or abrasives when cleaning Turn water supply off when servicing your ShowerSpa PULSE SHOWERSPAS Pulse ShowerSpas Inc 49 Hangar Way Suite A Watsonville CA 95076 888 785 7320 info pulseshowerspas com www pulseshowerspas com support pulseshowerspas com Part 1032 OM ENG Rev Y2012 11 01
7. cure fit h ly lines ROMERO 10 Connect hot and cold water supply lines to stub outs Remove handle s and trim cover s of your existing valve DO NOT OVERTIGHTEN Before mounting the ShowerSpa Care and Maintenance exposing valve body in wall check fittings to make sure they are secure Turn on water and check for leaks When fittings are leak free mount Locate hot and cold supply lines entering valve Using a Shomersns omyall reciprocating saw with sharp metal saw blade cut existing P i Always blot dry any water from the surface of your ShowerSpa To help protect your ShowerSpa from valve out preserving threads of the supply lines entering 11 OPTIONAL Seal around body of ShowerSpa with a bead of hard water stains and mineral deposits use an auto spray wax periodically and wipe down your Shower valve You should also cut the riser within wall supplying the existing shower head Carefully twist and remove valve Unscrew old shower head from shower arm and then un screw shower arm from the wall Water lines must be extended outside of wall cavity 4 2 on center For best results attach 90 brass fittings available at most hardware stores to the stub outs maintaining 4 2 of space between the fitting and finished wall The open end of the 90 brass fittings should point down so the supply lines attach parallel to the wall DO NOT INTERFERE with the backside of the ShowerSpa after mounting silicone DO
8. ference etc Installation Retrofit Thermostatic Mixing Valve The Hanalei ShowerSpa comes equipped with a thermostatic mixing valve to safely control water tem Existing Shower Replacement NOTE In a remodel in which you are not replacing the finished 7 Make certain that when you connect to the stub outs they wall surface tile or backing material it is advisable to pur chase a PULSE ShowerSpa model that covers the location of existing valve assembly either single handle or two handle 8 Mark location of holes for the mounting brackets mak type If your PULSE Sh Spa model do t cover th aa a ne heed e haces See E dc El ing sure holes are plumb For a person 5 8 6 2 tall we The button on the knob points to the current water temperature Rotate the knob counter clockwise to Spa model that does or make necessary repairs with appro recommend placing the holes of the upper bracket at 72 increase temperature or clockwise to decrease temperature Anti scald technology is provided by limiting priate materials i e wallboard tile fiberglass etc from finished floor height From the upper bracket holes temperature to 38 C 100 F unless the button on the knob is pressed To increase the temperature beyond a ag I measure down 42 for location of the lower bracket holes 38 C 100 F press the button and continue turning counter clockwise Each time you revisit your Shower TURN OFF WATER SUPPLY TO SHOWER Typically there
9. per maintenance misuse abuse negligence accident or alteration 2 the use of abrasive caustic or no rinse cleaning agents 3 the use of the product in any manner contrary to the product instruction 4 any condition in the home such as excessive water pressure or corrosion Should any ShowerSpa be determined by PULSE ShowerSpas Inc to be defective in normal residential use at the option of PULSE Shower Spas Inc such product shall either be replaced or repaired and returned to the customer free of defects The con sumer shall give notice of any defects to PULSE ShowerSpas Inc within thirty days of discovery of such defect Proof of purchase original sales receipt must be provided to PULSE Shower Spas Inc with all warranty claims PULSE Show erSpas Inc is not responsible for any labor charges removal charges installation or other consequential costs In no event shall the liability of PULSE ShowerSpas Inc exceed the purchase price of the ShowerSpa Some states provinces do not allow limitations of how long an implied warranty lasts or the exclusion or limitation of such dam ages so these limitations and exclusions may not apply to you This warranty gives the consumer specific legal rights You may also have other rights that vary by state province Follow manufacturers recommended installation Use caution with children under ten years of age Do not use ShowerSpa as a support device Do not use harsh chemi
10. s before completing installation After The ShowerSpa Is Mounted To The Wall Connect The Handheld Shower and Shower Head 1 Insert a rubber washer 17 into the hex end of the handheld hose 9 and attach to the handheld holder 8 2 Place a rubber washer into the tapered end of the handheld hose and attach to the handheld shower 7 Place the tapered end of the hose into the handheld holder 3 Place a rubber washer 17 inside the threaded nut on top of the shower head 2 and attach to the shower arm 3 Installation New Construction Extensive Remodel New Finished Wall Surface 1 Prior to sheetrock stub out hot and cold supply lines NOTE Before drilling holes for the brackets make certain the beyond finished wall surface 4 2 on center For best results attach 90 brass fittings available at most hardware stores to the stub outs maintaining 4 Y2 of space between the fitting and finished wall The open end of the 90 brass fit tings should point down so the supply lines attach parallel to the wall 2 The height of the stub outs is completely dependent upon the desired mounting height of your Hanalei ShowerSpa For a person 5 8 6 2 we recommend the stub outs be 35 from finished floor 3 Before installation make certain that water is completely turned off to both hot amp cold supply lines of the shower 4 Mark location of holes for the mounting brackets making sure holes are plum
Download Pdf Manuals
Related Search