American Standard 4433.001.002 Installation Guide
Contents
1. CANADA 1 800 387 0369 TORONTO 1 905 306 1093 Weekdays 8 00 a m to 7 00 p m EST IN MEXICO 01 800 839 1200 Product names listed herein are trademarks of American Standard Inc AS America Inc 2011 M965115_Rev 1 52. tightening the screws slightly each time until all are snug to ensure even pressure MOUNTING SURFACE P MAKE WATER SUPPLY CONNECTIONS Turn off hot and cold water supplies before beginning Connect FLEXIBLE SUPPLIES 1 2 directly to wall supplies Connection on fitting supplies are 3 8 compression Connect left supply to Hot Marked with a Red Line and right supply to Cold wall supply Use adjustable wrench to tighten connections Do not over tighten Faucet supplies are 21 long from faucet base Note If additional supply length is required installer must purchase additional parts separately Important If SUPPLY HOSES 1 2 are too long loop as illustrated to avoid kinking INSTALL SPRAY HOLDER E On model with separate spray place the SPRAY HOLDER 1 into the appropriate mounting hole Assemble the SPRAY HOLDER WING NUT 2 onto the shank of SPRAY HOLDER 1 from below and hand tighten Do not use putty m For installation less spray cap off SPRAY HOSE CONNECTION 3 with PIPE CAP 4 CONNECT HOSE SPRAY SPRAY HOSE 3 E Feed SPRAY HOSE 5 through SPRAY CONNECTION HOLDER 1 and attach COUPLING NUT 6 of HOSE 5 to SPRAY HOSE CONNECTION 3 on valve body Tighten COUPLING NUT 6 firmly 4 TEST INSTALLED FAUCET m Move HANDLE down into off position and remove AERATOR 1 E Turn on water supplies and check connections for leaks m mM Operate HANDLE 2 up and down left and right to flu
3. Installation Instructions QUINCE 4433 001 SINGLE CONTROL KITCHEN 4433 001F15 FAUCET WITH CAST SPOUT Thank you for selecting American Standard the benchmark of fine quality for over 100 years To ensure that your installation proceeds smoothly please read these instructions carefully before you begin Certified to comply with ANSI A112 18 1M M965115_Rev 1 5 Recommended tools SES Regular Screwdriver Phillips Screwdriver Adjustable Wrench Plumbers Putty or Caulking 1 INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON WeJ ijpy e turn off hot and cold water supplies before beginning Make certain the SEAL 9 is properly seated in recess of spout base m A Installation with ESCUTCHEON 1 Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE 1 Insert supply HOSES 2 and SHANK 8 through hole of ESCUTCHEON with PUTTY PLATE 1 and mounting surface Follow mounting instructions below to secure faucet to mounting surface E B Installation less ESCUTCHEON 1 Insert all HOSES 2 and SHANK 3 through MOUNTING RING 10 and mounting surface Do not use putty E Assemble RUBBER WASHER 4 BRASS WASHER 5 and threaded LOCKNUT 6 onto SHANK 3 from underside of sink or mounting surface Hand tighten LOCKNUT 6 and check that rotation of HANDLE 7 from HOT to COLD is centered m Use a screwdriver to tighten SCREWS 8 on LOCKNUT 6 Work your way around LOCKNUT 6
4. nd remove HANDLE 3 m Remove ESCUTCHEON CAP 4 Unscrew the three CARTRIDGE SCREWS 5 Clean MANIFOLD 710 CARTRIDGE 6 ports and SEALS 18 E Clean inlets of CARTRIDGE 6 and MANIFOLD 10 m Reassemble CARTRIDGE 6 alternately tightening SCREWS 5 Replace CAP 4 and HANDLE 3 Check flow CARE INSTRUCTIONS DO SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER DRY WITH A SOFT COTTON FLANNEL CLOTH DO NOT DO NOT CLEAN THE PRODUCT WITH SOAPS ACID POLISH ABRASIVES HARSH CLEANERS OR A CLOTH WITH A COARSE SURFACE M965115_Rev 1 5 QUINCE SINGLE CONTROL KITCHEN FAUCET WITH CAST SPOUT MODEL NUMBERS 4433 001 4433 001F15 030126 0070A M964003 YYYOA BUTTON AND HANDLE KIT SCREW KIT M962980 YYYOA ESCUTCHEON CAP M918506 0070E CARTRIDGE SCREWS A951470 0070A CARTRIDGE Replace the YYY with 042850 0070A Appropriate finish code DIVERTER 066070 YYYOA 2 2 GPM AERATOR L M922881 YYYOA 1 5 GPM E AERATOR NS Soe M907679 YYYOA SF C2 MOUNTING RING KIT UUU M953678 YYYOA HANDSPRAY amp HOSE RRR bi peters A911758 0070A SEAL M962980 YYYOA ESCUTCHEON AND PUTTY PLATE M962521 YYYOA SPRAY HOLDER M962146 0070A MOUNTING KIT 050448 0070A WEIGHT 060341 0070A PIPE CAP HOT LINE FOR HELP For toll free information and answers to your questions Call 1 800 442 1902 Weekdays 8 00 a m to 6 00 p m EST IN
5. sh water lines thoroughly m For faucet with spray direct SPRAY HEAD 3 into sink and activate SPRAY 3 Check hose connections for leaks m E Move HANDLE 2 down to off position and replace AERATOR 1 CHECK CONNECTIONS FOR LEAKS M965115_Rev 1 5 5 SERVICE Reduced flow If the flow gradually reduces over a number of months the AERATOR 12 may have collected debris To clean remove AERATOR 12 and rinse with water and remove any debris Turn on faucet to wash any debris out of the faucet Thread AERATOR 12 back into spout Operate faucet E Spout leakage If fitting leaks above or below SPOUT HUB remove SPOUT as follows and check SPOUT O RINGS First turn off water supply m Remove HANDLE BUTTON 2 and loosen SET SCREW 1 with 2 5mm HEX WRENCH 11 supplied Pull HANDLE 3 off valve stem Pull off CAP 4 Loosen CARTRIDGE SCREWS 5 and remove CARTRIDGE 6 Remove SPOUT 7 by pulling up gently while moving SPOUT 7 side to side Check both SPOUT O RINGS 8 for damage Replace if necessary On models with SPRAYS DIVERTER 9 can be cleaned by pulling DIVERTER 9 out of the MANIFOLD 10 Rinse clean the DIVERTER 9 and MANIFOLD 1710 Push DIVERTER 9 back into MANIFOLD 10 m Reverse procedure to reinstall SPOUT CARTRIDGE and HANDLE E Clogged CARTRIDGE outlets or inlets may cause reduced flow To clean first turn off water supply then E Remove PLUG BUTTON 2 loosen HANDLE SCREW 1 a
Download Pdf Manuals
Related Search