Weatherables YTPG-HSB5-12X12 Installation Guide
Contents
1. Place your post skirt I over your that your concrete mounts are matching vinyl post H Place the post over the in height by using one of your rafters If concrete mount posts heights are not the same you will need to choose the lowest concrete mount to base the height of your posts After leveling cut your vinyl posts accordingly from the bottom weatherables by USA Vinyl Section 3 Header amp Rafter Prep amp Installation E First position the headers L into the routed Looking down into your installed post at slots Make sure there is at least a 5 over your rafter drill a 1 hole using the 10 hang from the end of the header to the post drill bit extension Place a self tapping on each side Then position the rafters J screw into the hole to secure the rafter to into the slots making sure there is at least a your header Repeat for each post 3 1 2 overhang 8 Position the rafters approximately 22 24 Use the 10 x 1 self tapping screw C on center Do not attach until you have to secure the rafter spaced the rafters first If you modify the width these measurements will change The rafters will extend at least 5 past the header on the outside weatherables by USA Vinyl Section 4 Purlin Installation Start from the back and place the first Once properly positoned use the 10 x purlin K 5 from the post Space the 2 5 self tapping scre2. Miramar Single Beam Freestanding Pergola with 5 5 Posts Installation Guide Patent Pending Copyright 2013 USAVinyl LLC All Rights Reserved The information contained in these instructions are proprietary to USAVinyl LLC and may not be used or reproduced for any purpose other than for the evaluation purpose for which it was provided weatherables by USA Vinyl Before You Begin Installation Consult your local authorities for any permits required to construct the pergola Check with local building code officials to review any required permits or building limitations Read instructions thoroughly prior to assembly If you have questions or concerns with this product please DO NOT return before consulting a product specialist Please refer all questions and concerns to our product specialist at 1 888 743 3673 Due to the size of the parts at least two people are required to handle fit and secure pergola components Read manual first as mounting hardware varies with each application Do not anchor to paver bricks Foundation must be a solid surface Do not stand sit store or hang items on the pergola Repair or replace broken parts immediately Call 1 888 743 3673 for replacement parts At regular intervals inspect your pergola to make sure that assembly integrity has been maintained The installation video can be found at http www usavinyl com vinyl pergola installation html Tools Required for I
3. natallation 1 Extension Cord 10 Deep Socket 9 16 2 Hammer Drill 11 Level 3 Reciprocating Saw 12 Tape measure min 25 optional only if you are cutting 13 2 Ladders for at least the height of down material your pergola 4 Power Drill 14 Rubber Mallet 5 1 Drill Bit for metal 15 Ratchet 6 Drill Bits 5 16 3 16 16 Pencil 7 Phillips Screwdriver Bit 17 String Line 8 Masonry Bit 3 8 18 Carpenter s Square 9 10 Drill Bit Extension 19 Safety Glasses weatherables by USA Vinyl Hardware 8 4 5 10 x 2 1 2 Self Wedge Anchor 10 x 1 Self Tapping Screw Tapping Screw with washer and nut N SX CS Hinged lt Screw Cap Insert screw into cap before installing Hardware Quantities 12x12 88 8 44 128 14x14 90 12 52 1 138 16x16 119 12 60 1 Post Parts 5 Federation 54 Concrete Post Cap Post Mount e Dost 5 Post DressSkirt Post Parts Quantity Canopy Parts Projection Rafters 2 x 6 Hollow Vinyl Sleeve with Extruded Alum Insert 3 O 1 5 x1 5 Purlin Headers 2 x 8 Hollow Vinyl Sleeve with Extruded Alum Insert Decorative End Decorative End 2256 2 8 2 x 9 Purlin Cap Support Bracket Canopy Parts Quantity Section 1 The Posts A Preparation for Post Ins
4. tallation The post layout below is a suggestion for squaring your posts other methods can be used to get the same results The formula for squaring post 18 Bae Ex 144 144 20 736 20 736 20 736 41 472 441 472 203 65 B headers width h Rost ac 12x12 144 144 4 203 65 rafters 237 63 A projection 14x14 168 168 6 271 53 16x16 192 192 6 weatherables by USA Vinyl Post Set Up Lay out and mark the location of the posts according to the pergola size If you have a 14 or 16 pergola place the middle post directly in the center of the width side Place wedge anchors B into each hole and tap into concrete leaving 1 above the concrete Place concrete post mount G over the installed anchors and install washer and nut to each anchor Level and tighten with 9 16 socket Do not over tighten Place square and trace each concrete post mount G Pre drill concrete mount holes with hammer drill at 4 1 2 depth with 3 8 masonary bit Do not rush Note If you have a 14 or 16 pergola you will have 2 extra posts to place in the middle For the 14 pergolas the middle post will not be routed for the 2 x6 rail The rafters will be evenly spaced on the header weatherables by USA Vinyl Section 2 Vinyl Sleeve Installation Check to see if your post are level and
5. ws A and hinged remaining purlins evenly The overhang screw caps E to secure the purlins to the should be the same on both sides rafters Do not over tighten the screws as this will cause dents in the purlin weatherables by USA Vinyl Section 5 Finish Work St Ss Place and secure the 5 post caps F decorative ends M N and purlin caps P 14x14 with glue D 12x12 weatherables by USA Vinyl
Download Pdf Manuals
Related Search