MUSTEE 99 Instructions / Assembly
Contents
1. DURAPAN U S PATENT NO 5 452 739 ROUGH IN FOR 2 DWV ELASTOMERIC SEAL DRAIN MODEL 99 l WASHING MACHINE PAN Made from extra tough Durastone p 4 H T FRONT REMOVABLE THRESHOLD TOP OF SUB OPTIONAL INSTALLATION ds FINISHED RECESS COMPLETE DURAPAN P FLOOR INTO SUB FINSHED FLOOR THIS ALLOWS WASH MACHINE TO BE INSTALLED OR REMOVED FOR SERVICE WITHOUT LIFTING i Lye po Dm para Y l E A LL SSSSSS FRON Er E L 5431 West 164th Street Brook Park Ohio 44142 REMOVABLE THRESHOLD NOT SHOWN Check DURAPAN carefully making sure it is not damaged Refer to the rough in drawing and determine location Assemble drain to DURAPAN see illustration use all washers provided Do not use any putty or thread sealant on either drain body or locknut Hand tighten locknut then wrench an additional 3 4 turn maximum Provide a 5 inch square opening In the sub floor or slab This opening to be located at center of DURAPAN location Drain connection requires a 2 inch waste pipe Top of waste pipe must be even with top of sub floor or slab If DURAPAN has been recessed into sub floor top of waste pipe must be even with bottom of DURAPAN You will notice that there are 4 four countersunk holes in the floor area for securing DURAPAN to sub floor Using a 1 4 inch dia drill bit drill2. N SEALING WASHER 1 8 PN 42 319 FIBER WASHER LOCKNUT PN 42 305 PN 32 207 i DRAIN SEAL PN 42 318 s SQUARE OPENING 2 IRON ABS OR PVC DWV PIPE SANITARY DRAIN NOTE TOP OF PIPE TO BE EVEN WITH TOP OF SUB FLOOR AN OPTIONAL DRAIN SEAL PART NO 42 320 IS AVAILABLE FOR 2 COPPER DWV PART NO 42 321 IS AVAILABLE FOR 2 SOIL PIPE SW NO HUB FOR REPLACEMENT DRAIN ASSEMBLY COMPLETE ORDER PART NO 99 300A PARTS ILLUSTRATION CARE AND CLEANING The surface of your DURAPAN Wash Machine Overflow Base may be cleaned with a mild soap solution in warm water using a soft cloth For stubbom stains use Soft Scrub by Clorox or Lysol Tub amp Tile Cleaner or a powdered detergent such as Spic n Span Never use abrasive scouring powder or steel wool pads as they will dull and scratch the surface A periodic coating of a silicone based marine polish will help retain the fine finish Upp IAPMO LISTED FILE NO 4680 w PARTS LIST KEY NO PART NO DESCRIPTION 1 99 102 DURAPAN OVERFLOW BASE 2 99 401 THRESHOLD SEAL 3 99 201 THRESHOLD 4 99 801 140 24 X 1 2 THRESHOLD SCREW 2 REQUIRED 5 99 803 3H4 X 1 1 4 FLAT HD SCREW 4 REQUIRED 6 17 806 ANCHOR MOLDED 4 REQUIRED 7 42 309 STRAINER MOLDED 8 42 318 2 DRAIN SEAL 9 42 317 DRAIN BODY MOLDED 10 32 214 WASHER SEALING 1 16 THICK 11 42 319 WASHER SEALING 1 8 THICK 12 32 207 WASHER FRICTION 13 42 305 L
3. OCKNUT MOLDED SI 178 09 06
4. out each hole Place DURAPAN directly on sub floor as a template and mark the four previously drilled holes onto the sub floor surface Remove DURAPAN and drill the appropriate sized holes as determined by sub floor composition Wood 3 16 inch dia drill Cement 3 8 inch dia drill for anchors supplied Reposition DURAPAN align screw holes apply a dab of silicone sealant into each hole and secure with 3H4 x 1 1 4 Flat Head Screws Wipe away any excess sealant that seeps out from under screw head Seal waste by installing drain seal around 2 inch waste pipe Tamp in place to bottom of drain body using a 1 4 inch diameter rod or punch Make sure top of drain seal is even with top of 2 inch waste pipe as shown in sectional view and in full compliance with local code regulations pertaining to below floor sanitary waste connections The removable Threshold is secured with two 410 24 x 1 2 Pan Hd Screws remove screws insert Seal into recessed track Trim excess from ends After wash machine has been set in place reinstall threshold MUSTEE amp SONS INC SI 178 09 06 CAUTION DO NOT USE ANY PUTTY OR THREAD SEALING COMPOUND UNDER FLANGE OR ON THREADS OF DRAIN BODY FAILURE AND LEAKAGE MAY RESULT DO NOT OVERTIGHTEN LOCKNUT HAND TIGHTEN THEN WRENCH AN ADDITIONAL 3 4 TURN MAXIMUM ___ STRAINER PN 42 309 1 SEALING WASHER 1 16 DRAIN BODY PN32214 PN42317 SSH SUB FLOOR DURAPA
Download Pdf Manuals
Related Search