Patriot Docks 10850 Instructions / Assembly
Contents
1. 6 1 2008 PATRIOT DOCKS ASSEMBLY INSTRUCTIONS PATRICI Doc k Ne gt RAIL IN A A SL Congratulations on your new Patriot Dock purchase This manual contains instructions to assemble basic dock configurations for use at typical shoreline application It is possible to add sections and combine configurations to the basic configurations as long as installation guidelines are adhered to subject to lake and shoreline conditions Please refer to www patriotdocks com for answers to frequently asked questions and other suggestions US Dock and Hardware LLC Harris MN www usdockandhardware com www patriotdocks com 651 674 2450 STRAIGHT El uron conversion 5 PIPE SLEEVE WHEEL END PB wee eno DOCK PIPE amp FOOT PAD STRAIGHT SECTIONAL DOCKS STRAIGHT ROLL IN DOCKS ROLL IN PATIO DOCKS BE COCK section a x 6 General Guidelines 1 Maximum recommended unsupported span for Patriot Aluminum Dock Frames is 16 feet Always support outside corners Use additional posts to add stability as necessary 2 Always use Patriot Dock Pipe Post Brackets PN 10810 Post Foot Plates PN 10811 and 1 Schedule 40 galvanized pipe PN 10812 10815 for support posts on Patriot Docks Installing other parts may result in an unstable dock or unsafe installation 3 Always install Vinyl Pipe Caps PN 10823 on top of support pipes to avoid injury from sharp edges 4 Never leave the end of the dock unsupported Always support bo2. Suggestions or statements concerning possible use of products are made without representation that any such use is free from patent infringement and are not recommendations to infringe any patent The user must be aware that other safety measures may be required if not stated herein
3. ardware LLC be liable for any special incidental or consequential damages including but not limited to personal injury property damage damage to or loss of product loss of profits or revenue The price stated for the products is a consideration in limiting US Dock and Hardware LLC liability and buyers remedy 3 This limited warranty shall not apply to any product subject to misuse due to common negligence or accident nor to any product made by the seller not used in accordance with the printed instructions or specifications of US Dock and Hardware LLC or that have been beyond the represented and rated capacity of the product 4 This limited warranty is applicable only to those parties heretofore mentioned and is not assignable transferable nor will it insure to the benefit of any sub purchaser of the original equipment manufacturer other than the original retail purchaser 5 Application may be subject to local building codes and is the responsibility of the purchaser to adhere to 6 As stated above US Dock and Hardware LLC reserves the right to inspect all panels claimed to be defective or damaged under the terms of the warranty 7 US Dock and Hardware LLC limits of warranty is defective material replaced repaired or credit against further purchases All information and data provided at time of writing is believed to be accurate and complete however are provided without any guarantee or responsibility of any kind expressed or implied
4. ations 4 Wide Roll In Kit PN 10825 with 4 ft axle and 6 ft posts for straight dock applications note posts may be ordered longer as necessary and 8 Wide Roll In Kits PN 10826 with 8 ft axle and 8 ft posts for patio platform docks The wheel adds one foot to support height Each Roll in Kit includes 2 Pipe Post Brackets 2 Support Pipes Axle Pipe Wheel Clamps Washers and Wheels 2 Plastic Wheel PN 10821 Optional Deep Water Pipe Brace Kit Deck Lockers PN 10828 PN 10867 PATRIOT DOCK ASSEMBLY INSTRUCTIONS SHORE END LAKE END SHORE END SHORE END LAKE END ASSEMBLE ALUMINUM FRAME 1 Lay out each 4 ft X 8 ft Aluminum Frame Assembly PN 10800 end to end in the desired basic configuration on a flat surface e Remove each component from the 4 ft X 8 ft Aluminum Frame Assembly packages and unwrap the protective plastic from the components e Place the 8 ft long Side Frame Rails in two lines making sure the ends marked SHORE are pointing to one direction and the ends marked LAKE are pointed in the opposite direction e Place the End and Middle Rails and Connector Rail between the Side Frame Rails as shown 2 Starting from the left SHORE end of the layout fasten the 4ft End Frame Rail to the Side Frame Rails using 4 3 8 16 X 1 0 inch bolts and nuts for each Position each end inside the vertical corner angle of the Side Frames Finger tighten bolts and nuts until all frame components are assembled 3 Fa
5. ck frame located 4 ft towards shore from the Pipe Brackets for the Roll In Kit Use connector strap to connect other end to vertical pipe support on Roll In Kit approximately 3 feet below dock frame If there is not enough pipe bolt brace to top hole on vertical angle of dock frame instead 4 Carefully roll or set the dock in place Additional helpers may be needed Adjust pipe supports to level the dock Use winch tool jack come along or other means to raise or lower dock Tighten set bolts on Pipe Post Brackets Make sure the long aluminum frame braces are installed on the underside of frame 5 Install Decking A For pre assembled Cedar Decking Sections PN 10870 set 4 x 4 sections in openings in frame B For pre assembled poly Dock Top Sections PN 10860 set 4 x 4 sections in openings in frame Rotate each Deck Locker if included under frame side rails to secure the decking to the dock frame Note To assemble poly panel lay 4 individual panels upside down with Dock Top logos in same direction on a flat surface and install 6 Deck Connecting Clips PN 10859 at the panel joints approximately 12 inches from the edge as indicated below using a hammer Install 4 or 6 Deck Lockers PN 10867 between the panels with screws in the pre drilled holes located about 2 1 4 inches from the edge mount with swivel end to outside of panel Fewer Deck Lockers may be needed when creating a continuous decking sheet where all sections are c
6. mes Middle Frame Rails Connector Frame Rails and Center Support Tubes by repeating steps 1 7 until the straight part of the dock frame is assembled Fasten the final End Frame Rail PN 10803 packaged separately to the Lake end of the dock using 4 3 8 16 X 1 0 bolts and nuts If holes do not match up use drill with 3 8 bit to size Discard Lake end Connector Frame Rail 9 Install diagonal aluminum Brace to the bottom of each Side Frame Rail pair using two 3 8 16 X 1 0 bolts and nut in an alternating pattern reverse direction from one 8 ft frame to the next so braces form continuous zigzag These can also be installed later for easier access to underside of frame 10 Patio Docks Attach 4x8 Frame section to side of last 4x8 Frame using 6 3 8 16 X 1 625 bolts and nuts Make sure to face the SHORE end of the added Patio Frame facing the Shore end of the main dock frame Fasten the End Frame Rail PN 10803 packaged separately to the Lake end of the dock using 4 3 8 16 X 1 0 inch bolts and nuts Discard Lake end Connector Frame Rail Install ladder uprights now 11 L Docks Lateral sections can only be added to the Lake end of an 8 ft Frame Assembly The Lake end or Connector Frame Rail end of the lateral is fastened to the straight main sectional dock after main dock is placed For T repeat procedure so that the distance between ends of laterals is 20 ft total 12 Check to make sure the frame components are flush and tighten all bol
7. o years after the purchase date and a prorated warranty from two to seven years after the date of purchase The prorated warranty provides replacement at a percentage discount off the current manufacturer s suggested retail price MSRP US Dock and Hardware LLC may repair replace or provide a full or partial refund at its sole discretion according to the following terms The claimant must present the defective panels to the authorized dealer from which they were originally purchased along with the original purchase invoice or receipt The dealer will then submit a warranty claim to US Dock and Hardware LLC If US Dock and Hardware LLC certifies that the items are indeed defective US Dock and Hardware LLC will repair replace or provide a prorated discount on replacement of the defective Dock Top panels as follows Year 1 Full Replacement Year 2 Full Replacement Year 3 Replacement at 50 of MSRP Year 4 Replacement at 60 of MSRP Year 5 Replacement at 70 of MSRP Year 6 Replacement at 80 of MSRP Year 7 Replacement at 90 of MSRP WARRANTY LIMITATIONS The successful performance of the Dock Top panel is dependant upon many factors beyond our control Therefore except for such replacement or refund outlined above US Dock and Hardware LLC 1 MAKES NO WARRANTY OR GUARANTEE EXPRESS OR IMPLIED INCLUDING WARRANTIES OF FITNESS and DESIGN CAPABILITY OR MERCHANTABILITY RESPECTING ITS PRODUCTS 2 Under no circumstances shall US Dock and H
8. onnected with Deck Connecting Clips on permanent installations Secure panels to Shore Ramps with cable ties or screws CAUTION Always secure decking to the frame using cable ties screws or Deck Lockers oF E Eei i i gi 1 T 1 er o e m mn View Assembly Photos Hints and FAQs at www patriotdocks com www dock top com LIMITED WARRANTY US Dock and Hardware LLC provides a limited warranty for plastic Dock Top decking panels to the original purchaser only when purchased from an authorized dealer The Dock Top is not warranted in conjunction with other products not manufactured by US Dock and Hardware LLC INTENDED USE Dock Top panels are intended to be installed on marine docks as decking and are not intended for any other use The limited warranty is valid only when used for the intended application Purchasers should fully inspect each Dock Top panel before installing WARRANTY Providing that Dock Top are installed as per the instructions supplied Redtail International LLC warrants that a Dock Top M will not delaminate b Dock Top will not rot c Dock Top will not absorb water d Dock Top M will not degrade from UV rays does not include fading or light discoloration e Dock Top M panels are sold is in accordance with published specifications and are free of material or workmanship defects TERMS US Dock and Hardware LLC provides a full repair or replacement warranty for the first tw
9. sten the center 4ft Middle Frame Rail to the Side Frame Rails using 4 3 8 16 X 1 0 inch bolts and nuts Again position each end inside the vertical angle on the Side Frames 4 Position the 4 ft Connector Frame Rail to the Side Frame Rails using 2 3 8 16 X 1 625 inch bolts but do not install the nuts yet Make sure the welded tab on the Connector Frame Rail faces away from the assembled frame 5 Install the Short Center Tube Support between the End and Middle Frame Rails on the SHORE end of the first 4X8 Frame Rail Assembly and install the Long Center Tube Support between the Middle Frame Rail and the Connector Rail on the Lake end of the frame assembly Use 4 3 8 16 X 1 0 inch bolts and nuts and 2 3 8 16 X 1 625 inch bolts and nuts Note The 2 longer bolts are passed through the Connector Rail and the next Middle Frame Rail 6 Move on to next connecting 4x8 Frame Assembly Loosely fasten the next set of Side Frame Rails AND the End Frame Rail of the second frame to the first set of Side Frame Rails using the 3 8 16 X 1 625 inch bolts and nuts in step 4 The Connector Rail of the first Frame Assembly stays in place 7 Install an additional 2 3 8 16 X 1 625 bolts nuts and bolts to secure the bottom of the Side Frame Rails and Middle Frame Rail Note The End and Middle Frame Rails and Connector Frame Rails are always positioned inside the welded vertical aluminum angles on the Side Frame Rails 8 Continue fastening the Side Fra
10. ted connections with tools INSTALL PIPE SUPPORTS AND ROLL IN KITS 1 Install Pipe Post Brackets PN 10810 using Y 13 X 1 inch bolts provided as shown on the basic configuration layouts The nuts are slipped into the pockets and the shorter bolts fasten the brackets to the Side Frame Rail The 12 13 X 1 25 inch bolts are stainless steel and should be screwed into the weld nuts on the Post Bracket CAUTION Maximum span between post supports is 16 feet Shore Ramps require support posts at the shore end use washers for spacers to install these post brackets 2 Slip Support Pipe PN 10812 10815 through Pipe Post Brackets and install Foot Plate PN 10811 For Roll In Kits install Axle Converters PN 10820 instead of the foot plates pointing the long part of the horizontal axle converters towards each other 3 For Roll In Kits slip axle through pipe converters slide wheels amp washers in place and fasten Wheel Clamps to axle pipe to keep wheels in place Maintain a 1 8 inch gap between wheel and Axle Converter when fastening clamp For straight docks use 6 ft axle pipe and fasten wheels to the ends of the pipe outside the dock frame For Patio Docks use 8 ft axle pipe and fasten the wheels inside the dock frame adjacent to the Axle Converters Tighten bolts 1 2 turn after bolt contacts pipe Retighten as necessary Add optional Pipe Stabilizer Brace Kit by bolting one end to lower 1 2 inch diameter hole in welded vertical angle of do
11. th corners of the Patio platform Roll in kits should be installed at the very end of the dock for best stability Additional posts may be required if roll in kits are installed at locations other than shown above 5 Always assemble the dock frame so there is a 4 foot End Rail PN 10803 at the ends of the dock For patio or platform docks two End Rails are required may have to be purchased separately For straight sectional docks only one End Rail is required If lateral sections are to be added to the sectional dock to form an L shape a separate End Rail is not required 6 When adding lateral frame sections to create an L shaped configuration not shown in basic configurations install the LAKE end Connector Rail end of the added frame towards the straight main dock Add two Support Pipes to the end of every lateral section 7 Install the Pipe Brace Kit PN 10828 in conjunction to the Roll In Kit for lakes with soft bottoms or deep water applications The brace kit will help prevent potential bending of the Support Pipes 8 Always secure supports posts and level dock before installing deck panels Remove decking panels whenever possible when pulling the frame out of the water to prevent bending the dock frame 9 Maximum recommended distance between wheel kits for long dock applications is 32 feet 10 Secure poly decking with cable ties as necessary to prevent shifting Wear protective gloves File any sharp edges on pipes and frame to a
12. void cuts or scrapes If you have parts missing contact your dealer before proceeding For accessories replacement parts FAQ and warranty information and detailed assembly directions with hints please visit www patriotdocks com TOOLS NEEDED 9 16 and 3 4 Wrenches amp Ratchet w Sockets Hammer Phillips Screwdriver or Drill May Be Required Knife Drill with 3 8 Bit Flat File 1 12mm Socket Pliers COMPONENT IDENTIFICATION 1 The 4 x 8 Aluminum Truss Frame PN 10800 includes the following components 2 Side Frames 2 Middle Rails 1 Connector Rail Same as End Rail PN 10803 2 Center Tubes 8 ft Diagonal Brace 12 3 8 16 X 1 0 Bolts Nuts 11 Long and 1 Short 6 3 8 16 X 1 62 Bolts Nuts 2 The Support Post Assembly PN 10816 10819 includes 112 Schedule 40 Galvanized Support Pipe available in 4 ft 6 ft 8 ft and 10 ft lengths plus the following components 1 Pipe Post Bracket 1 Post Foot Plate 1 Vinyl Cap PN 10810 PN 10811 PN 10823 3 Decking is available in Cedar Drop in Sections PN 10870 or in Poly Dock Top Sections PN10860 Four molded Dock Tops and at least 6 Deck Clips PN 10869 are required to assemble each 4x4 Poly Dock Top Section Cedar Deck Section Poly Dock Top Section Deck Clips PN 10870 PN 10860 PN 10869 4 Various Roll in Kits are available for Patriot Docks Shore End Roll In Kit PN 10824 with 4 ft axle and 4 ft posts for shore end or shallow applic
Download Pdf Manuals
Related Search