Eagle EDIBO Instructions / Assembly
Contents
1. Since manufacturer has no control over handling use or storage no guarantee expressed or implied is offered Eagle IFP Company warrants the product to be free of defects and will replace or refund the purchase price of said products proven defective Labor cost and or other consequential damages are not covered by this warranty Responsibility for claims of any kind is strictly limited to the purchase price of the product The suitability of the product for any extended use shall be solely up to the user Made in U S A EAGLE IFP COMPANY www eaglesealer com2. palette or applied over a base color for a unique look Depending on the depth of color that is desired more than one application may be required Use clean water or acetone to rinse the sprayer between color changes Keep a container of clean water or acetone available and place the end of the sprayer wand into it between applications to keep the tip from becoming clogged SEALING The surface must be sealed with a clear concrete sealer to lock in and protect the color If dye residue is present remove with white buffing pad and tackcloth Do not use water A light initial coat of sealer should be applied to the dyed surface with a pump sprayer to lock in the dye Apply sealer per the manufacturer s instructions If using water based dyes wait 4 hours to start sealing with a water based sealer and 8 hours for solvent based sealer If using acetone based dye you can seal immediately Spray apply first coat of sealer Water based Eagle ARMOR SEAL will work if floor is not too tight For on going maintenance clean with water only and use Eagle CONCRETE POLISH for ongoing scuff protection and maintenance Apply 2 3 coats initially per the label s instructions and touch up periodically as a regular maintenance routine COVERAGE RATE Approximately 200 400 square feet per gallon depending on porosity and depth of color desired TECHNICAL DATA HMIS VOC lt 15 g L Health 1 Flammability 2 Flash Point 150 Reactivity 0 Protection B DISCLAIMER
3. INTERIOR CONCRETE DYE INTERIOR CONCRETE DYE is a penetrating dye that adds color to existing interior concrete This coloring method provides an elegant decorative appearance without the harsh chemicals or tedious and expensive process of acid based chemical staining Beginning with a properly prepared surface INTERIOR CONCRETE DYE can be applied and sealed in as little as one day minimizing down time Nano particles allow the color to penetrate the concrete resulting in a durable treatment that will not wear away with traffic Seal with Eagle ARMOR SEAL POMEGRANATE PINEAPPLE BLACK ORCHID WARM HONEY RHUBARB DANDELION COLA MALT BROWN RED BERRY THISTLE GREEN BLUEBERRY ROOT BEER SWEET POTATO VIOLET BLUE POPPY MAPLE SYRUP ROAST PEPPER Mixes Instantly Into Solution No Additional Mottling Agent Required INTERIOR DYE TOOLS amp MATERIALS REQUIRED Pump up sprayer with conical tip Painters masking tape and plastic sheeting Synthetic bristle brush Clean water for cleaning equipment White buffing pad and tack cloth EAGLE ETCH amp CLEAN EAGLE CLEANER DEGREASER amp NEUTRALIZER EAGLE ARMOR SEAL EAGLE CONCRETE POLISH TEST BEFORE PROCEEDING Test an inconspicuous area to be sure that concrete accepts stain and color meets expectation before proceeding Test for water seep by taping plastic on one square foot of floor Remove plastic the following day If floor is wet you should not stain and seal fl
4. cloth or into the small container immediately after releasing the spray handle Apply the dye uniformly to obtain a more uniform final appearance Apply in a random circular motion with some overlapping to generate a more mottled look that more closely resembles acid stain Colors may be blended to produce an infinite palette or applied over a base color for a unique look Depending on the depth of color that is desired more than one application may be required Use clean water to rinse the sprayer between color changes Keep a container of clean water available and place the end of the sprayer wand into it between applications to keep the tip from becoming clogged COVERAGE RATE Approximately 200 400 square feet per gallon depending on porosity and depth of color desired SEALING The surface must be sealed with a clear concrete sealer to lock in and protect the color If dye residue is present remove with white buffing pad and tack cloth Do not use water A light initial coat of sealer should be applied to the dyed surface with a pump sprayer to lock in the dye After applying dye wait 4 hours to start sealing with EAGLE ARMOR SEAL and 8 hours for solvent based sealer If using acetone based dye you can seal immediately For ongoing maintenance clean with water only and use EAGLE CONCRETE POLISH for ongoing scuff protection and maintenance Apply 2 3 coats initially per the label s instructions and touch up periodically as a regular mainte
5. nal volume of 1 gallon To use larger capacity sprayers adjust volumes SURFACE PREPARATION All walls furniture columns or other items areas that you do not want to color should be masked using painter s tape and plastic sheeting This will protect the items from overspray Concrete should be cured and clean free of dirt dust residue and oil Pre etch and clean with Eagle ETCH amp CLEAN until concrete readily absorbs water For oily surfaces Eagle DEGREASER NEUTRALIZER is recom mended Power wash the surface at 3000 psi If not possible scrub with clean water and remove excess Allow to dry 24 hours APPLICATION Always do a test spot in an inconspicuous area before proceeding with the project Apply with a pump up sprayer using a conical fine spray tip Small areas can be brushed using a circular motion to avoid brush strokes Take care to maintain a wet edge to avoid bleed lines Do not apply more material than the surface will absorb in 1 minute If not using a Drip Less Sprayer tape a piece of cloth or a small container to the sprayer body to catch drips while not spraying the material Place the tip of the spray wand on the cloth or into the small container immediately after releasing the spray handle Apply the dye uniformly to obtain a more uniform final appearance Apply in a random circular motion with some overlapping to generate a more mottled look that more closely resembles acid stain Colors may be blended to produce an infinite
6. nance routine TECHNICAL DATA HMIS VOC lt 15 g L Health 1 Flammability 2 Flash Point 150 Reactivity 0 Protection B DISCLAIMER Since manufacturer has no control over handling use or storage no guarantee expressed or implied is offered Eagle IFP warrants the product to be free of defects and will replace or refund the purchase price of said products proven defective Labor cost and or other consequential damages are not covered by this warranty Responsibility for claims of any kind is strictly limited to the purchase price of the product The suitability of the product for any extended use shall be solely up to the user Made in U S A EAGLE IFP COMPANY www eaglesealer com Eagle INTERIOR CONCRETE DYE TOOLS amp MATERIALS REQUIRED Pump up sprayer with conical tip Acetone resistant sprayer if using acetone Eagle ETCH amp CLEAN If not using DRIP LESS Sprayer absorbent cloth or small container to catch drips Eagle DEGREASER NEUTRALIZER Painter s masking tape and plastic sheeting Synthetic bristle brush Clean water for cleaning equipment Eagle ARMOR SEAL White buffing pad and tackcloth Eagle CONCRETE POLISH DYE PREPARATION INTERIOR CONCRETE DYE concentrate should be transferred into a 1 gallon sprayer Use clean water or acetone to rinse the residue from the concentrate bottle into the 1 gallon container Repeat this step until all SUPER DYE is out of the bottle Add clean water or acetone to a fi
7. oor SURFACE PREPARATION All walls furniture columns or other items areas that you do not want to color should be masked using painter s tape and plastic sheeting This will protect the items from overspray Concrete should be cured and clean free of dirt dust residue and oil Pre etch with EAGLE ETCH amp CLEAN until concrete readily absorbs water Dense concrete surfaces may require mechanical preparation to accept dye For oily surfaces EAGLE CLEANER DEGREASER amp NEUTRALIZER is recommended Scrub surface with clean water and remove excess Allow to dry 24 hours APPLICATION EAGLE INTERIOR CONCRETE DYE concentrate should be transferred into a 1 gallon sprayer Use clean water to rinse the residue from the concentrate bottle into the 1 gallon container Repeat this step until all EAGLE INTERIOR CONCRETE DYE is out of the bottle Add clean water to a final volume of 1 gallon To use larger capacity sprayers adjust volumes Always do a test spot in an inconspicuous area before proceeding with the project Apply with a pump up sprayer using a conical fine spray tip Small areas can be brushed using a circular motion to avoid brush strokes Take care to maintain a wet edge to avoid bleed lines Do not apply more material than the surface will absorb in 1 minute If not using a drip less sprayer tape a piece of cloth or a small container to the sprayer body to catch drips while not spraying the material Place the tip of the spray wand on the
Download Pdf Manuals
Related Search