Weider C133 User's Manual
Contents
1. NN 1076 VA ASSEMBLY INSTRUCTIONS REPLACEMENT PARTS WEIDER HEALTH AND FITNESS 21100 ERWIN ST WOODLAND HILLS CA U S A 9136 TABLE OF CONTENTS REPAIR PARTS AND SERVICE STEP 1 FRAME ASSEMBLY i TEP 2 BACKREST PREPARAT ATTACHING BACKREST AND SEAT STEP 4 ATTACHING LEG CURL m bav O k o z Aw Co gt 2099 PARTS LIST ene NO PART NAME ORDERING NUMBER 2 MAIN FRAME 4 0201 0101 _ 3 FRONT SUPPORT 1 0129 A15 4 LEG 14 0138 0211 3 I BACKREST 4 00389 020 T 6 ser 1 lj 0370 6010 O TITO TOV PAD BAR 2 j 6053 A09 FOAMPAD 1 4 j 0425 05__ 9 BACKREST ADJ BR 1 1 06054 A06 x 40 LONG ANGLE IRON 1 2 06047 A09 r T L BRACKET 2 06140 C10 FR TT HEGRE EE Norr EET HARDWARE BAG 1 1 C5804 C13 rT A 1 3 4 ROUND PLASTIC CAP 1 4 AA 8004 8 1 ROUND PLASTIC CAP 1 1 AA 8005 1 COVER CAP 4 JO aa 8070 7 TD 2 SQUARE PLASTIC CAP 2 AA 8002 TE 4 1 2 SQUARE PLASTIC CAP 3 ____ 8001__ 3 8 16 X 2 1 2 HEX HEAD BOLT 14 HH 5018 me 13 80 46 LOCK NUT 2 1__ BH 013 15 5 16 20 X 2 1 2 HEX HEAD BOLT 8 HH 5015 y 5 16 20 LOCK NT 1 8 HH 5021 x kK 1 4 20 X 3 4 MACHINE SCREW 6 HH 5022 ant UPRIGHT DECAL 1 2 DE 4071 x _INSTRUCTION MANUAL 1 1 NN 1076 pREASSTASTEV _ PREASSEMBLED IN BACKREST amp SEA REPAIR PARTS2. proper hole in LEG CURL 4 until egual amounts of bar are on both sides of LEG CURL 4 Slide one FOAM PAD 8 onto each end of PAD BAR 7 Insert PLASTIC CAP A into each end of PAD BAR 7 Insert PLASTIC EEEREN PLASTIC CAP E into end of LEG CURL 4 Insert PLASTIC CAP B into weight pin on LEG CURL 4 Slide COVER GJ over rear extended piece of weight pin on LEG CURL 4 4
3. AND SERVICE ALL OF THE PARTS FOR THE WEIGHTBENCH CAN BE ORDERED FROM WEIDER HEALTH AND FITNESS PARTS SERVICE DEPT 900 WEST ST JOHN ST OLNEY ILL 62450 WHEN ORDERING PARTS WILL BE SENT AND BILLED AT THE CURRENT PRICES PRICES MAY BE SUBJECT TO CHANGE WITHOUT NOTICE STANDARD HARDWARE ITEMS ARE AVAILABLE AT LOCAL HARDWARE STORES TO OBTAIN PARTS DO NOT GO BACK TO THE STORE WHERE YOU PURCHASED THIS UNIT IF YOU FIND THIS PRODUCT TO HAVE EITHER A DEFECTIVE PART OR A MISSING PART WRITE THE ABOVE ADDRESS OR PHONE CUSTOMER SERVICE 1 800 225 0653 ALWAYS INCLUDE THE FOLLOWING INFORMATION WHEN ORDERING PARTS MODEL NO NAME OF PART ORDERING NUMBER C133 STEP 1 FRAME ASSEMBLY AR pl by inserting 2 S RA E PLASTIC CAPS D into UPRIGHT 1 Align bolt holes on L BRACKE with bolt holes on UPRIGHT 1 Secure each L BRACKET 11 with 2 HEX HEAD BOLTS H and 2 LOCK NUTS J Align bolt holes on main frame u bracket and FRONT SUPPORT 3 Secure with 2 HEX HEAD BOLTS H and 2 LOCK NUTS J With UPRIGHT 1 standing lower rear u bracket of MAIN FRAME onto crossmembar of UPRIGHT 1 Align bolt holes and secure with 2 HEX HEAD BOLTS and 2 LOCK NUTS 3 Insert 2 SQUARE PLASTIC CAPS into FRONT SUPPORT 3 Tighten all bolts NOTE The lower or attachmant end of the BACKREST 5 can be identified quickly by the LONG _ ANGLE IRONS 10 The LONG ANGLE IRONS 10 will be ex tended approximately two inches
4. beyond the BACKREST PAD 5 STEP 2 BACKREST PREPARATION Turn BACKREST 5 over to expose work area Both LONG ANGLE IRONS 10 have been fastened to BACKREST 5 for shipment One Long Angle Iron must be loosened in order to assemble BACKREST 5 to Main Frame Pivot Rod The lower MACHINE SCREW K must be removed while the upper MACHINE SCREW K is only loosened The LONG ANGLE IRON 10 can now Swing freely from the lower end of BACKREST 5 DETAIL A 3 ATTACHING BACKREST amp SEAT BACKREST To aid in attaching Backrest first slide the BACKREST ADJ BAR 9 through one of the hole patterns in the Uprights With LONG ANGLE IRON 10 free lower BACKREST 5 to Main Frame Pivot Rod Slide the secured LONG ANGLE IRON 10 onto one side of Pivot Rod wing the free LONG ANGLE IRON 10 back to its original position and onto the opposite end of the Pivot Rod See Detail A Replace MACHINE SCREW K that was removed in Step 2 and tighten all Machine Screws SEAT With SEAT 6 right side up lower SEAT 6 to seat brackets on Main Frame Align bolt holes and fasten with MACHINE SCREWS K Tighten all Machine Screws STEP 4 ATTACHING LEG CURL Place LEG CURL 4 between Leg Curl Brackets on Main Frame and align bolt holes Secure with HEX HEAD BOLT F and LOCK NUT Repeat the following in structions until all PAD BARS 7 and FOAM PADS 8 are in place First slide PAD BAR 7 through
Download Pdf Manuals
Related Search