TriStar Deluxe SSMT1000 User's Manual
Contents
1. CT residents add 6 sales tax NY amp NV add applicable sales tax mail U S CURRENCY ONLY PACES SUB ECT TOC ANGE Please make checks payable to POWER JUICER Mail Payment Today To POWER J UICER 26 Barnes Industrial Rd North P O Box 3125 Dept PJ SS999 Wallingford CT 06494 11 TROUBLESHOOTING Problem The motor does not run after being switched on The motor Is running with loud noise and shaking The motor is running The spout is in the downward position but no juice is coming out The motor overheats causing the power to automatically shut off Juice splashes from the rim of the receptacle 10 Possible Reasons and Solution Check to see if unit is plugged in Locking bar is not locked in place properly Check if all parts are assembled properly Check if there is any residue left between blade and receptacle Check to see if food is stuck to the bottom of the pusher Check that all parts are assembled properly and in the correct position Juicing overripe fruit may result in too much pulp and will clog the filter Turn machine off and clean the filter Turn the power off and unplug the machine Wait for blade to stop spinning Use a toothpick to loosen any obstruction in the non drip spout The motor needs to warm up for 10 seconds before use The fruits and vegetables may be soft or overripe There may be too much pulp in the filter Turn machine off and cle2. to shut off the motor when it over heats Please use extreme caution when handling the Power Juicer blade as the blades are very sharp Always turn power off to the Power Juicer immediately and remove power cord from electrical outlet before disassembling to clean due to any food obstruction Use caution when handling blade as blades are very sharp If juicer jams turn power off immediately and remove power cord from electrical outlet before disassembling to clean The Power J uicer has a thermal cut off safety feature If the unit accidentally overheats it will stop working temporarily until the Power J uicer cools down Clear any obstruction Afterwards the unit will continue to work again normally HELPFUL HINTS O btain the best results from your Jack LaLanne Power Juicer by following these helpful hints Do not put any fruit or vegetables in your machine until power is turned on Allow unit to run for at least 10 seconds before juicing e Do not force food into the juicer Allow food to pass through slowly and steadily using the pusher You do not need to apply pressure unless the juicer starts to vibrate Then only a slightly harder push should bring it back to balance e Any fruit or vegetable that will fit the chute can be put through whole The only time it is necessary to cut is when something is too large Then it should be cut into large enough pieces to fit in the chute Do not cut pieces too small e Remove large pi
3. POWER JUICER fuck La dannes POWER JUICER M odel SSM T1000 Item 108709 2008 Tristar Products Inc All rights reserved Es Distributed by Tristar Products Inc Wallingford CT 06494 O PERATING M ANUAL PJ Deluxe V2 0508 TABLE OF CONTENTS 4 5 LO mwer gt DELUXE Liltirine 4 POWER JUICER Accessory Kit amp Cookbook e Recipes for Healthy Living Cookbook e Power J uicer Platform e Filter Brush e Overflow Platform e Measuring Cup a Se j feb Lainna POWER JUICER Pulp Collector r a Lid with i Pulp Guard Crescent 1 Tool OS Pusher To order or for more information on juicing visit WwWw powerjuicer com or call 1 800 526 2518 8 00am 9 00pm EST Monday Friday 9 00am 5 00pm EST Saturday amp Sunday Please allow 4 6 weeks for shipping YES Please Send Me the following Items One Accessory Kit amp Cookbook for only 19 99 Print Name O plus 6 99 s amp h Total 26 98 Recipes for Healthy Living Cookbook FREE Pee plus 7 99 s amp h Total 7 99 Replacement Parts Kit 1 foronly 29 999 eeaeee Apt plus FREE s amp h Total 29 99 Replacement Parts Kit 2 for only 34 99 lt 5 PNE plus FREE s amp h Total 34 99 VISA MasterCard Discover Exp Date___ Sc A CreditCard eee Phone OOOO De Check Money Order NJ residents add 7 sales tax PA amp
4. acing direction of locking bar Settle receptacle into alignment STEP 4 Place blade inside filter centered over screw peg Using orange crescent tool place its pegs into the holes in the blade and turn clockwise until tightened IMPORTANT Do not over tighten as the screw peg will break Remove crescent tool and set aside CAUTION Do not leave tool inside juicer ASSEM BLY cont s Lid with Pulp Guard Receptacle STEP 5 Place lid with pulp guard attached on top of receptacle making certain it is snugly aligned with the pulp guard facing in the opposite direction of the juice spout Lock lid into place by lifting locking bar up until it clicks into grooves located on both sides of the lid M ake sure locking bar is in the full upright locked position IM PORTANT The unit will not start until this bar is properly locked in place STEP 6 Insert pusher into chute Always use pusher to feed fruits and vegetables into unit Push gently never force The blade will do the work STEP 7 M ake sure juice spout is in the downward position If the juice spout is left in the upright position the juice will not flow It will stay in the receptacle and may overflow from the sides Lid with Pulp Guard DOWNWARD POSITIO
5. an the filter M otor stops running due to the built in feature the overheat safety control This is normal IM PORTANT SAFEGUARDS READ THESE SAFEGUARDS CAREFULLY BEFORE USING THIS PRODUCT NOT FOR USE BY CHILDREN Keep out of the reach of children to avoid injury This appliance is not a toy M ake sure the lid is attached properly and securely locked before operating the Power Juicer Do not unfasten the locking bar during operation To avoid risk of injury keep hands and utensils out of the juicer and away from its sharp blade during operation Use the pusher not fingers or utensils to propel the food into the juicer Should food become lodged in the opening use pusher to push it down If food remains stuck turn the power off wait until motor stops unit shuts down completely and is unplugged before disassembling the juicer and removing the blocked food M ake sure the motor stops completely and the unit is unplugged from the electrical outlet before cleaning putting on or removing parts To protect against risk of electrical shock or injury never immerse power cord plug or main unit in water or other liquids If juicer stops due to improper operation or if there is excessive noise turn power off wait for blade to stop spinning unplug from electrical outlet disassemble and clean all components then reassemble machine Do not operate this or any appliance with a damaged cord or plug Do not operate i
6. f appliance malfunctions is dropped or damaged in any manner Let a qualified appliance repair person examine and or repair appliance before using To avoid electric shock or serious injury do not use any attachments that were not recommended or sold by the manufacturer Do not let power cord hang over the edge of table counter or let cord touch hot surfaces such as stoves To reduce the risk of injury never place blade on base without properly assembling the unit This appliance has a polarized plug one blade Is wider than the other To reduce the risk of electric shock this plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician Do not modify or force the plug in any way The motor will not run if unit is not properly assembled The motor has a built in safety feature that will not let the power turn on unless the locking bar is locked in place ADDITIONAL SAFEGUARDS The Power Juicer has a thermal cut off safety feature If the unit accidentally overheats it will stop working temporarily until the Power Juicer cools down Afterwards the unit will continue to work again normally In the event the Power Juicer is jammed the motor may shut down If this occurs the juicer should be shut off and unplugged The unit should be thoroughly cleaned to remove the obstruction The thermal cut off safety feature is designed
7. ishwashers if you choose to wash the pusher in the dishwasher place it on top rack only e Clean all other parts in warm soapy water A mild detergent is recommended Rinse well and dry thoroughly All components are dishwasher safe with the exception of the base Do not use in European Import or a commercial dishwasher e To clean the filter and blade hold them under warm running water Use a soft bristled dish washing brush gently to completely clean pulp from filter Rinse the filter from the outside under running water e Dry components thoroughly then assemble the machine and turn the power on to spin out any excess water e Make sure unit and parts are completely dry then store in a cool dry place TO CLEAN THE J VICE SPOUT Lock STEP 1 Mechanism Locate removable juice spout locking mechanism on the bottom side of the receptacle Note Juice spout will be in the locked position STEP 2 To unlock turn locking mechanism counter clockwise lining up notch with juicer spout hinge pivot arm STEP 3 Lift up juice spout carefully from receptacle and remove to clean TO REATTACH Insert juice spout back into original position and turn the locking mechanism clockwise to lock into place IM PO RTANT When reattaching juice spout back into original position make sure juice spout is in the locked position and tightly secured before use 9 IM PO RTANT Before disassembling the unit D A E M E LY make sure you turn
8. the power OFF and unplug PA RTS LIS T the machine from the electrical outlet Locking Bar ae Guard Pulp Collector STEP 1 STEP 2 Remove pusher from the chute Lower the locking bar silver into position as shown Lid with Chute Pulp Guard Pulp g Collector Filter Pulp Guard STEP 3 STEP 4 Lid with Pulp Guard Remove lid with pulp guard and pulp Use the crescent tool orange to remove collector the blade Place the two pegs at either c Tool Crescent tool pegs fit here to tighten end of the crescent tool into the two rescent 100 WARNING DO NOT OVER TIGHTEN holes on the blade press down and turn for tightening and removing blade counter clockwise to unlock the blade Remove blade carefully Blade Pegs fit into blade Screw Peg Locking Bar Filter Removable Non Drip Spout UM Lip STEP 5 STEP 6 Remove filter M ake sure spout is in the upright position to avoid leakage Remove Receptacle 8 receptacle from base 5 AS S E M B LY Assemble as shown 1 Locking Bar Front of M achine Spout side STEP 1 Place base on a dry flat surface with locking bar in down position as shown In front of the machine spout side Crescent Receptacle Tool Place filter inside receptacle matching the opening on its bottom to the screw peg connected to the base Juice Spout Receptacle Place receptacle on the base with juicer spout f
9. ts such as peach mango etc as they will damage the blade and possibly the unit Before juicing cherries we recommend you remove the pits using a cherry pitter e Cleaning can be made easy by placing a plastic bag inside the pulp collector container When you are done juicing the bag can be lifted out and disposed of easily leaving the pulp collector easier to clean e Let the Power Juicer run for a few minutes before turning off to allow any excess juice to be extracted from the pulp Once turned off it is quite normal for the juicer to spin for a minute or so due to the very fine precision balancing of this appliance Wait until it is done spinning before disassembling e Do not use bananas or avocados as they do not contain juice and will clog machine Add them separately in a blender e We do not recommend using overripe fruit as it will leave too much pulp in the filter and clog the machine e Do not pour liquids into the machine at any time SAVE THESE INSTRUCTIONS CLEANING YOUR J UICER e Turn off the power switch and wait until the motor completely stops e With dry hands unplug the power cord from electrical outlet e Disassemble the machine See disassembly instructions e Wipe base with a soft damp cloth or sponge Do not submerge base in water Do not spray with water or any other liquid Base is not dishwasher safe e We recommend washing the pusher by hand in warm soapy water Due to temperature differences in d
Download Pdf Manuals
Related Search