Triarch 31021 User's Manual
Contents
1. Assembly Instructions ITEM NO 31021 4 CANOPY 1 COUPLING 7 GLASS SHADE 10 WAS SHERI paras 1 CAREFULLY TAKE THE FIXTURE OUT OF THE CARTON AND CHECK THAT ALL THE PARTS ARE INCLUDED REFERRING TO THE ABOVE DRAWING SURE NOT TO MISPLACE ANY PARTS THAT ARE NEEDED TO INSTALL THIS LAMP 2 REFER TO MOUNTING AND WIRING INSTRUCTION SHEET 3 PROTRUDE THE NIPPLE 5 THROUGH THE HOLE OF RING 6 THEN FIX IT BY FLAT NUT 4 4 ATTACHED THE TOP END OF THE ARM 3 ONTO THE CANOPY 1 FIX IT BY THE BALL STUD 2 5 THREAD THE HEX NUT 8 ONTO THE NIPPLE 9 THEN SCREW THE NIPPLE 9 INTO THE COUPLING 7 LOCK IT IN PLACE BY HEX NUT 8 6 SLIDE THE GLASS SHADE 10 WASHER 11 ONTO THE NIPPLE 9 IN ORDER THEN SECURE THEM WITH THE HEX NUT 12 7 SLIDE THE CAP 13 ONTO THE NIPPLE 9 FIX IT BY FINAL 14 8 INSTALL THE LAMPS ON 9 THE FIXTURE IS ASSEMBLED 12 READ 8 SAVE THESE INSTRUCTIONS ANA AAA E INSTALLATION OPERATION INSTRUCTIONS ans TOOLS amp MATERIALS REQUIRED Adjustable wrench Step Ladder Wire cutters Wiring supplics as required by electrical code CAUTION Before assembling your Lighting fixture refer to the section tided ELECTRICAL CONNECTIONS If you feel you do not bave electrical wiring experience refer to a do it yourself wiring handbook or have your fixture installed by a qualified licensed electrician GENERAL WARNING RISK OF FIRE MOST DWELLINGS BUILT BEFORE 1985 HAVE SUPPL2. TURE NOTE FIRST TURN OFF ELECTRICITY 1 If you are replacing an existing fixture disconnect and remove the old fixture Expose the supply wiring trom the outlet box 2 Some fixtures are provided with a threaded nipple see Fig 1 and Fig 5 or machine screws see Fig 2 and 2A for attaching the fixture to the mounting bracket If your fixture is supplied with a threaded nipple screw the nipple 3 complete tums into the mounting bracket and lock into place with a hexagon tock nut If your fixture is supplied with machine screw thread the machine screws into the opposite side of the mounting bracket from the green ground screw Lock the machine screws into place with lock nuts EXCEPTION Ceiling mounted fixtures with keyhole slots should have machine screws entering mounting bracket from same side as green grounding screw see Fig 2A 3 Fasten the mounting bracket to the outlet bax using the two screws supplied with the outlet box if your fixture is supplied with a channel shape mounting bracket with keyhole slots for attachment to the mounting surface see Fig 3 it will be neccessary to mark the location of the keyhole slots on the mounting surface and drill holes for fasteners not provided Use fasteners suiltable for the mounting surface The narrow end of the keyhole slot should face up 4 Attach grounding wire groen or bare copper from the supply circuit to the mounting bracket with the green grounding attachment screw provided Some models have a ground
3. Y WIRE RATED 60 C REFER TO SUPPLY WIRE MARKINGS ON FIXTURE CONSULT A QUALIFIED ELECTRICIAN BEFORE INSTALLING 1 To ensure the success of the installation be sure to read these instructions and review the diagrams thoroughly before beginning 2 All electrical connections must be in accordance with local codes ordinances or the National Electrical Code If you are unfamiliar with methods of installing electrical wiring secure the services of a qualified licensed electrician 3 Thesc fixtures are intended to be mounted to a 4 x 2 decp metal octagon outlet box The box must be directly supported by the building structure 4 Before starting the installation disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box Turning the power off using the light switch is not sufficient to prevent electrical shock NOTE The important safeguards and instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur It must be understood that common sense caution and care are factors which cannot be built into any product These factors must be supplied by the person s caring for and operating the fixture UNPACK THE FIXTURE Check the contents of the box You should receive Mounting hardwara package Lampholder assembly s Mounting bracket Shade not provided on all models Shade attachment screws 3 for each shade not provided on all models PREPARE THE FIX
4. ing wire attached to the fixture Far models that employ green or bare copper grounding wire it will be necessary to connect the the green or bare grounding wire to the grounding conductor of the supply circuit Attach all grounding conductors to the mounting bracket with the green grounding attachment screw 5 Make electrical connections SEE BELOW ELECTRICAL CONNECTIONS To make electrical connections Connect the white wire s from the fixture to the white wire of the supply circuit Connect the black wire s from the fixture to the black wire of the supply circuit Connect the green or bare copper colored wire to the grounding conductor of the supply circuit If your fixture is supplied with an SPT Cord connect the half of the SPT Cord that is ribbed surface 10 the white wire of the supply circuit Connect the smooth half of the wire the half with markiogs to the black wire of the supply circuit Use UL Listed wire connectors suitable for the size type and number of conductors No loose strands or loose wires should be present Secure wire connectors with U L listed electrical tape FINAL ASSEMBLY 1 Spread the electrical splices so that the black wires are on one side of the outlet box and the white wires are on the other side 2 Place fixture against mounting surface allowing the threaded nipple or machine screws to pass through the coverplate Secure with mounting out or acorn nuts For fixtures with channel shape mounting bracket p
5. lace the cover plate over the channel and secure with screws provided 3 If applicable place candle cover s over lampholder s before installing bulb s Install the lightbulb not provided CAUTION Refer to the relamping label located near the lampholder for recommended maximum wattage do not exceed recommended wattage 4 If applicable attach shades to fixture Some shades require the use of shade attachment screws Do not overtighten these screws too much pressure could cause glass breaking See Fig 4 for placement of fabric spacer not supplied on all modes 5 Outdoor wall fixtures must be caulked with suitable RTV or Silicone compound around the top and sides of the coverplate to reduce the chance of water intruding into the splicing area Leave the bottom clear ta allow moisture a means of escape 6 Restore electricity and check the operation of your new lighting fixture t gt Arandela de goma Fig 2 Cable a tierra FE EE Ganchos de montaje Tornillos de metal Blanco del cirevito Blanco de la l mpara Tuerca hexagonal Conexi n Ai Niple cubierto Colgante de techo Pantalla de vidrio Nota Estos dibujos muestran 1 instalacion de su nueva lampara mural Estos dibujos son DA Tapita 4 Punta de adorno representativos y no calzan estrictaments el estilo de su lampara mural
Download Pdf Manuals
Related Search