Sony HK-PSU01 User's Manual
Contents
1. Power switches Board retainer B 3x8 with stopper Board guides oard lever os lever SS Board retainer NE Slot label PFV SP3100 1 5 Installing Optional Board 6 Reinstall the board retainer Installing Connector Panel Rear side 7 Reinstall the front panel The connector panel must be installed to the slot which contains the main board When removing the main board turn the board lever in the direction of the arrow and pull out the board toward 1 Remove the two screws and remove the blank panel of you the slot which contains the main board Keep the removed blank panel and two screws Board lever Blank panel 2 Connect the connector panel to the MB 992 board 3 Secure the connector panel with the two screws MB 992 board Connector panel Do not open the slot for an air cooled effect of this unit Attach the blank panel to an empty slot PFV SP3100 1 5 E 1 6 Rack Mounting 1 6 Rack Mounting PFV SP3100 can be mounted on a 19 inch standard rack for use Mount PFV SP3100 on the rack properly in the procedure below using a specified rack mounting kit Specified rack mounting kit RMM 10 PFV SP3100 may not be able to be mounted on a 19 inch standard rack using a rack mounting kit other than the specified one Components of RMM 10 Rack brackets ecne a a A a 2 pcs e2. position OFF Otherwise deterioration of a connector which connects HK PSUO1 to PFV SP3100 may cause a fire Installation Procedure 1 Loosen the two screws and remove the front panel Screw with stopper Front panel Screw ne with stopper 2 Remove the two screws and remove the blank panel in the empty slot for the backup power supply unit Keep the blank panel which is removed PSW 3x6 PSW 3x6 Blank panel PFV SP3100 1 4 Installing Removing Optional Power Supply Unit 3 Make sure that the power switch of the backup power supply unit HK PSU01 is set to the O position OFF 4 Insert HK PSUO1 into PFV SP3100 and push it by hand as far as it will go 5 Secure HK PSUO1 with the two screws which is removed in step 2 If installation of the power supply unit is incomplete contact resistance of the connector increases and that may cause damage and smoke Tighten firmly the screws that secure the power supply units Do not turn on the power until the power supply units are firmly secured HK PSU01 Handle 6 Reinstall the front panel 7 Connect the power cord and set the power switch to the T position ON 8 Make sure that the indicator lights LNote If the indicator does not light turn off the power and contact your local Sony Sales Office Service Center Removal Procedure 1 Turn off the power of the
3. Rack mounting adaptor right eee eeeeeseeeeeeeee 1 pe Including two screws B 4X6 7 682 560 09 e Rack mounting adaptor left eee eeeeeeeeeeeeeeees 1 pe Including two screws B 4X6 7 682 560 09 e Rack bracket fixing screws B 4X6 7 682 560 09 Required other parts To mount the unit on the rack the following parts are required e Screws for rack mounting B5X12 7 682 576 04 1 6 1 Notes on Rack Mounting Fix the rack on the horizontal and firm floor with bolts to prevent it from turning over or moving If the rack overturn due to the weight of the unit this may cause a death or serious injury e After rack mounting be sure to tighten the screws of the rack angle and fix this unit to the rack If not this unit may slide and fall from the rack This causes an injury Attention when this unit is installed in the rack e Use the specified rack mounting kit Be careful not to put your hand or finger in the rack mount rail e Install in a stable posture Install a ventilating fan in the rack to prevent the increase in the temperature inside a rack when multiple units are put in one rack 1 6 2 Rack Mounting Procedure Explains the procedure for rack mounting by Rack Mount Kit RMM 10 Fasten the screws at the tightening torque below Tightening torque 1 2 Nem 12 2 kgf cm 1 Attach the rack brackets in the side panels of the unit with the specified six screws Be sure to use B4X6 as a s
4. in water and then dried completely PFV SP3100 2 2 Periodic Replacement Parts to Be Recommended The fan used on the rear panel of this unit is periodic replacement parts to be recommended The life of the fan is approximately 50 000 hours The life corresponds to about five years and a half if the power is on all the time so the fan should be replaced according to service conditions For the replacement of the fan refer to the optionally available PFV SP3100 Maintenance Manual 2 1 E TOV Aa FIVER S TVD BA OEE EY FEIT HOES tio C tora IZURRI CHE LED WHENA GHE RAPS CRRAZRN CAV IAEA TS CeEPRIELET The material contained in this manual consists of information that is the property of Sony Corporation Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation Le mat riel contenu dans ce manuel consiste en informations qui sont la propri t de Sony Corporation Sony Corporation interdit formellement la copie de quelque partie que ce soit de ce manuel ou son emploi pour tout autre but que des op rations ou entretiens de l quipement a moins d une permission crite de Sony Corporation Das in dieser Anleitung enthaltene Material besteht aus Informationen die Eigentum
5. power supply unit which you want to remove Set the power switch to O posi tion 2 Unplug the power plug from the wall outlet 3 Remove the front panel 4 Remove the screws securing the power supply unit 5 Pull out the power supply unit from the slot using its front handle 6 Install the blank panel 7 Reinstall the front panel 1 3 E 1 5 Installing Optional Board 1 5 Installing Optional Board The optional board can be installed in any empty slot of PFV SP3100 When installing the processing module controller the No 4 slot is used as the master slot and the No 3 slot is used as the sub slot Installing Main Board Front side Two slots are used depending on the optional board In this section the illustrations for the single slot type s board are described 1 Turn off the power switches of PFV SP3100 Turn off both of the power switches when the backup power supply unit is installed Remove the front panel Refer to Section 1 4 3 Loosen the four screws and remove the board retainer Insert the main board fully into the slot along the board guides and close the board lever in the direction indicated by arrow Stick the slot label supplied with the PFV SP3100 onto the board lever Note Attach the supplied slot label to the position where it is not concealed by the board retainer as shown in the figure Slot 3 Slot 1
6. SONY SIGNAL PROCESSING UNIT PFV SP3100 BACKUP POWER SUPPLY UNIT HK PSU01 INSTALLATION MANUAL 1st Edition serial No 10001 and Higher PFV SP3100 serial No 10001 and Higher HK PSU01 ASS TOVIaAT Id C EXAHA CTS BARN COVIaYIVIZARANERMIEPRT AR HR ERTS ECMBPKE AFFBUZDEMATEMHBOVET fERRA SWATH D EFARV HRV RSUI ERMA OACHA lt S ESV A WARNING This manual is intended for qualified service personnel only To reduce the risk of electric shock fire or injury do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so Refer all servicing to qualified service personnel A WARNUNG Die Anleitung ist nur f r qualifiziertes Fachpersonal bestimmt Alle Wartungsarbeiten d rfen nur von qualifiziertem Fachpersonal ausgef hrt werden Um die Gefahr eines elektrischen Schlages Feuergefahr und Verletzungen zu vermeiden sind bei Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen Andere als die angegeben Wartungsarbeiten d rfen nur von Personen ausgef hrt werden die eine spezielle Bef higung dazu besitzen A AVERTISSEMENT Ce manual est destin uniquement aux personnes comp tentes en charge de l entretien Afin de r duire les risques de d charge lectrique d incendie ou de blessure n effectuer que les r parations indiqu es dans le mode d emploi moins d tre qualifi pour en effectuer d autres Pour toute r paration faire appel un
7. cord only Be sure to use a recommended power cord to avoid fire and or an electric shock e Ground the unit for your safety Be sure to attach a ground wire to avoid an electric shock 1 1 E 1 3 Installation Space 1 3 Installation Space e Do not block the ventilation holes of the unit Both of the front and rear sides must be at least 20 cm away from the walls for ventilation and mainte nance The outer dimensions of PFV SP3100 are as shown here SERER QQOQQOOQOOO 550 43 6 440 SONY O O SIGNAL PROCESSING UNIT PFV SP3100 9900000 900000000000 299009990009000000000000000000000090000000900000000000000000000000000000000 900090 990000000000 88099999999090090009090099000000000009999999000000000000900000000000009 900000 000000000000 999909099999090090000000000900000090000000000000000000000000900000000000 900090 990000000000 899099909999999090009090099999000000909999999000000000000900000000000009 900000 090000000000 1909000900900000000000000000000000000000000000 888880 3 000000000000 80000000000000000000000000000000000000000 482 Unit mm 1 2 E PFV SP3100 1 4 Installing Removing Optional Power Supply Unit Before installing the backup power supply unit HK PSUO1 in PFV SP3100 set the power switch of HK PSUO1 to the O
8. crew B 4x6 Rack bracket B 4x6 Rack bracket 2 Loosen the screws at the rear of the each adaptor before adjusting each adaptor length to the rack depth Following figure is case of left side PFV SP3100 The maximum depth of an adaptor is 750 mm The minimum depth of an adaptor is 595 mm 3 Firmly lay the right and left adaptors in the rack with the specified six screws Following figure is case of left side RMM 10 o og 0o o 00 o0 o Front H ay N K hss P 31 75 B 4x10 Rear SAA Ne B 4x10 EES 31 75 o o 4 Fasten the length adjustment screws which are loosened in step 2 5 Remove the front panel Refer to Section 1 4 6 Align the crook of the each rack bracket on the side panels of the unit with the rail then slide the unit backward Each rack bracket covers the rails as shown in the figure below IN Rack bracket Rail Rack bracket Rail x PFV SP3100 1 6 Rack Mounting 7 Fix the unit to the rack with the specified screws 8 Reinstall the front panel 1 7 E 1 7 Matching Connector Cable 1 8 Signal Inputs Outputs 1 7 Matching Connector Cable When external cables are connected to the connectors on the PFV SP3100 rear panel the hardware listed below or the equivalent must be used PFV SP3100 connector Matc
9. der Sony Corporation sind Die Sony Corporation untersagt ausdr cklich die Vervielfaltigung jeglicher Teile dieser Anleitung oder den Gebrauch derselben f r irgendeinen anderen Zweck als die Bedienung oder Wartung der in dieser Anleitung beschriebenen Ausr stung ohne ausdr ckliche schriftliche Erlaubnis der Sony Corporation PFV SP3100 Printed in Japan PFV SP3100 SY J E Sony Corporation 2002 7 22 3 690 471 01 B amp P Company 2002
10. e personne comp tente uniquement For the U S A PFV SP3100 Attention when the product is installed in Rack 1 Prevention against overloading of branch circuit 5 Install the equipment while taking the operating When this product is installed in a rack and is temperature of the equipment into consideration supplied power from an outlet on the rack please For the operating temperature of the equipment refer make sure that the rack does not overload the supply to the specifications of the Operation Manual circuit 6 When performing the installation keep the rear of 2 Providing protective earth the unit 10 cm 4 inches or more away from walls When this product is installed in a rack and is in order to obtain proper exhaust and radiation of supplied power from an outlet on the rack please heat confirm that the outlet is provided with a suitable protective earth connection 3 Internal air ambient temperature of the rack When this product is installed in a rack please make sure that the internal air ambient temperature of the rack is within the specified limit of this product 4 Prevention against achieving hazardous condition due to uneven mechanical loading When this product is installed in a rack please make sure that the rack does not achieve hazardous condition due to uneven mechanical loading PFV SP3100 PFV SP3100 Table of Contents Manual Structure Purpose of this manual 20 0 0 cee eescecencecseceeseee
11. eeeessecescecseecsaeceaeeceeseneeeeeeeneeeeaeens 2 E Related Mantals iscccsccscstetvecdevtesceaedovsed a a a a e ENE SAES 2 E 1 Installation 1 1 Operating Environments eiar ani a 1 1 1 2 Power Supply cemer iseen erneer to aee EE EE EN R E R S 1 1 1 2 1 Power Supply Specifications 00 0 eseeeeceeeeseeseeeees 1 1 1 2 2 Recommended Power Cord ccccssecssceceesseecseeeeeesseeeeees 1 1 E 1 3 Installation Space seo ao eerie iee seh e EE E TRENE Er 1 2 E 1 4 Installing Removing Optional Power Supply Unit 0 eee 1 3 1 5 Installing Optional Board ssssseeseeesessseeseesresssreerrsrerrsreserreserrrsrenesseeres 1 4 E 1 6 Rack Mounting 2 0 00 ecs cceisceveavescteestevvecessecevsasecceuaeceasscebgecbvee shusvepnenanas 1 6 E 1 6 1 Notes on Rack Mounting 00 cece eesseceneeceeeeenceeeeeenteeeeneees 1 6 E 1 6 2 Rack Mounting Procedure eeesseceeeeceseeeneeceneeeneeeeneees 1 6 E 1 7 Matching Connector Cable cceeceesccescecereecsseeecceeseeeeneceeeceaeeeseeceees 1 8 E 1 8 Signal Inputs Outputs 0 eee ee eseeeee cee cae ceeaecaeesecseeeeeseeeeeeeees 1 8 E 2 Service Overview 2 1 Cleaning the Filter 0 0 0 0 cess eccessessssvensconnsssvscsnssesnseseceoseesnsevseseosnsesnes 2 1 2 2 Periodic Replacement Parts to Be Recommended ceeeeeeeeeseeeeeee 2 1 Manual Structure Purpose of this manual This manual is the installatio
12. ensation Approx 8 5 kg Without the optional unit and board Approx kg Operating temperature Performance temperature Humidity Mass PFV SP3100 HK PSUO1 To prevent overheating of PFV SP3100 ensure that there is good air circulation around the unit Do not put the unit in a place subject to excessive lamp smoke vapor moisture or dust otherwise a fire or electric shock may result Install in a stable location Installation on unstable or tilting surface may cause the unit fall off resulting in injury PFV SP3100 1 2 Power Supply 1 2 1 Power Supply Specifications AC 100 V to 240 V 50 Hz or 60 Hz 1 0 to 0 5 A AC 100 VIN 10A AC 240 VIN 33 A Power voltage Power frequency Current consumption Rush current AC power supply is required a capacity which is commen surate with rush current If the capacity of the AC power supply is not enough the breaker of AC power on the supply side may operate or this unit may not operate normally 1 2 2 Recommended Power Cord For customers in the U S A and Canada Required Part Power cord 125 V 10 A 2 4 m A 1 557 377 11 For customers in the United Kingdom Required Part Power cord 250 V 10 A 2 5 m A 1 782 929 11 AC inlet AC inlet u E For the customers outside of the area as shown above please contact your local Sony Sales Office Service Center Use a specified power
13. hing connector cable Print on Connector type Connector type Sony Part Number REMOTE BNC 75Q BNC 759 1 569 370 12 REF IN A B Belden 1694 coaxial cable STATUS OUT D sub Mini 15 pin Female D sub Mini 15 pin Male 1 8 Signal Inputs Outputs The input and output signals of the connector on the rear panel are as shown here STATUS OUT D sub Mini 15 pin female 5000001 O OOO OO O lt External view gt Pin No I O Signal Function All pins are low in level Description under normal conditions 1 O PS A ERROR OUT State of power unit A The output of power unit A is abnormal The fan of power unit A stops 2 O PS B ERROR OUT State of power unit B The output of power unit B is abnormal The fan of power unit B stops O FAN ERROR OUT State of frame ventilation fan The frame ventilation fan stops 4 O BOARD ERROR Error status output of optional board Error output from optional board OUT Overpower consumption from optional board 5 O BOARD WARNING Warning status output of optional board Warning output from optional board OUT 6 O BOARD ERROR 1 Error status output of board installed in Error output from the optional board installed in OUT the No 1 slot the No 1 slot 7 O BOARD ERROR 2 Error status output of board installed in Error output from the optional board installed in OUT the No 2 slot the No 2 slot 8 O BOARD ERROR 3 Error status output of board installed in Error output from the optional board in
14. n manual of Signal Processing Unit PFV SP3100 and its Backup Power Supply Unit HK PSUO1 This manual is intended for use by trained system and service engineers and describes the information for installation of the unit The functions and specifications of HK PSU0O1 and PFV SP3100 s power supply unit are equal This manual uses Power Supply Unit for HK PSUO1 and PFV SP3100 s power supply unit Related manuals The following manuals are prepared for PFV SP3100 e Operation Manual Supplied with PFV SP3100 This manual describes the notes on operating the locations and functions of parts and controls of PFV SP3100 e Maintenance Manual Available on request This manual describes the information for periodic maintenance and detailed service If this manual is required please contact your local Sony Sales Office Service Center e Semiconductor Pin Assignments CD ROM Available on request This Semiconductor Pin Assignments CD ROM allows you to search for semiconductors used in B amp P Company equipment Semiconductors that cannot be searched for on this CD ROM are listed in the service manual for the corresponding unit The service manual contains a com plete list of all semiconductors and their ID Nos and thus should be used together with the CD ROM Part number 9 968 546 XX PFV SP3100 Section 1 Installation 1 1 Operating Environment 5 C to 40 C 10 C to 35 C 10 to 90 No cond
15. stalled in OUT the No 3 slot the No 3 slot 9 O BOARD ERROR 4 Error status output of board installed in Error output from the optional board installed in OUT the No 4 slot the No 4 slot 10 O BOARD WARNING Warning status output of board installed Warning output from the optional board installed 1 OUT in the No 1 slot in the No 1 slot 11 O BOARD WARNING Warning status output of board installed Warning output from the optional board installed 2 OUT in the No 2 slot in the No 2 slot 12 O BOARD WARNING Warning status output of board installed Warning output from the optional board installed 3 OUT in the No 3 slot in the No 3 slot 13 O BOARD WARNING 4 Warning status output of board installed Warning output from the optional board installed OUT in the No 4 slot in the No 4 slot 14 15 GND 1 8 E PFV SP3100 Section 2 Service Overview 2 1 Cleaning the Filter Be sure to turn off the power switch and disconnect the power cord from the outlet before starting any work e The temperature inside the unit increases if dust adheres to the filter and the ventilation holes are blocked Touching inside the unit while it is hot may result in burn injuries e Clean the filter on the rear of the front panel periodically because the filter tends to gather dust once every two months Procedure 1 Remove the front panel Refer to Section 1 4 2 Remove the dust from the filter using a vacuum If the filter is very dusty it should be washed
Download Pdf Manuals
Related Search