Snapper 1807-1 User's Manual
Contents
1. the nozzle extension to the spray gun and attach all hoses shut off device such as a Y shut off connector or other before you start the engine convenience type water shut off valve l Uncoil high pressure hose and attach one end of hose Damage to equipment resulting from failure to follow this to base of spray gun Figure 4 Tighten by hand instruction will void warranty Figure 4 Connect High Pressure Hose to Spray Gun 6 Turn ON water and squeeze trigger on spray gun to purge pump system of air and impurities A WARNING High pressure spray can cause paint chips or other particles to become airborne e Always wear eye protection when using this equipment or in vicinity of where equipment is in use Connect Hose and Water Supply to Pump Connect high pressure hose here 2 Attach other end of high pressure hose to high pressure outlet on pump Figure 5 Tighten by hand Before starting the pressure washer be sure you are wearing adequate eye protection C SNAPPER by Briggs amp Stratton POWER PRODUCTS Checklist Before Starting Engine Review the unit s assembly to confirm you have performed all of the following Make sure handle is in place and secure 2 Check that oil has been added to proper level in engine crankcase Add proper fuel to fuel tank 4 Check for properly attached hose connections 5 Check to make sure there are no kinks cuts or damage2. 3 Place filter end of chemical injection hose into detergent container CAUTION Keep the chemical injection tube from coming in contact with the hot muffler When inserting the filter into a detergent solution bottle route the tube so as to keep it from inadvertently contacting the hot muffler by Briggs amp Stratton POWER PRODUCTS 4 Slide adjustable nozzle forward to low pressure mode Detergent cannot be applied with nozzle in high pressure position 5 Make sure garden hose is connected to water inlet Check that high pressure hose is connected to spray gun and pump Start engine 6 Apply detergent to a dry surface starting at lower portion of area to be washed and work upward using long even overlapping strokes 7 Allow detergent to soak in for 3 5 minutes before washing and rinsing Reapply as needed to prevent surface from drying DO NOT allow detergent to dry on prevents streaking IMPORTANT You must flush the chemical injection system after each use by placing the filter into a bucket of clean water then run the pressure washer in low pressure for l 2 minutes Pressure Washer Rinsing For Rinsing l Slide nozzle backward to high pressure press trigger and wait for detergent to clear NOTE You can also stop detergent from flowing by simply removing chemical injection hose from bottle 2 Keep spray gun a safe distance from area you plan to spray Snapper 2300 PSI Pressure W
3. Check High Pressure Hose The high pressure hose can develop leaks from wear kinking or abuse Inspect the hose each time before using it Check for cuts leaks abrasions or bulging of cover damage or movement of couplings If any of these conditions exist replace the hose immediately A WARNING The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues leading to serious injury and possible amputation NEVER repair high pressure hose Replace it e Replacement hose rating MUST exceed maximum pressure rating of unit Check Detergent Siphoning Tube Examine the filter on the detergent tube and clean if clogged The tube should fit tightly on the barbed fitting Examine the tube for leaks or tears Replace the filter or tube if either is damaged Check Gun and Adjustable Nozzle Extension Examine the hose connection to the spray gun and make sure it is secure Test the trigger by pressing it and making sure it springs back into place when you release it Put the safety latch in the ON position and test the trigger You should not be able to press the trigger Purge Pump of Air and Contaminants To remove air from the pump follow these steps Setup pressure washer as described in Preparing Pressure Washer For Use Connect water supply and turn water on amp SNAPPER Briggs amp Stratton POWER PRODUCTS 2 Pull trigger on spray gun and
4. NEVER repair high pressure hose Replace it Keep high pressure hose connected to pump and spray gun while system is pressurized Snapper 2300 PSI Pressure Washer by Briggs amp Stratton POWER PRODUCTS A WARNING Running engines produce heat and hot exhaust gases Temperature of muffler and nearby areas can reach or exceed 150 F 65 C Fire or severe burns can occur A CAUTION Excessively high or low operating speeds increase risk of injury and damage to pressure washer DO NOT tamper with governed speed DO NOT operate pressure washer above rated pressure DO NOT touch hot surfaces Stay clear of exhaust gases Allow equipment to cool before touching A WARNING V Starter and other rotating parts can entangle hands hair clothing or accessories DO NOT wear loose clothing jewelry or anything that may be caught in the starter or other rotating parts Tie up long hair and remove jewelry A WARNING High pressure spray can cause paint chips or other particles to become airborne Always wear eye protection when using this equipment or in vicinity of where equipment is in use A WARNING 7 4 Unintentional sparking can result in fire or W electric shock uv WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE WASHER Disconnect spark plug wire from spark plug and place wire where it cannot contact spark plug A CAUTION A pressure washer produces a
5. hold 3 When water supply is steady and constant engage safety latch To remove contaminants from the pump follow these steps Setup pressure washer as described in Preparing Pressure Washer For Use Connect water supply and turn water on 2 Remove nozzle extension from spray gun 3 Start engine according to instructions in How To Use Pressure Washer 4 Squeeze trigger on spray gun and hold 5 When water supply is steady and constant engage safety latch and refasten nozzle extension Check In Line Filter Refer to Figure 2 and service the in line filter if it becomes clogged as follows Figure 12 Clean In Line Filter Extension I Detach spray gun and nozzle extension from high pressure hose Detach nozzle extension from spray gun and remove o ring and screen from nozzle extension Flush the screen spray gun and adjustable nozzle extension with clean water to clear debris 2 If screen is damaged the o ring kit contains a replacement in line filter screen and o ring If undamaged reuse screen 3 Place in line filter screen into threaded end of nozzle extension Direction does not matter Push screen in with eraser end of pencil until it rests flat at bottom of opening Take care to not bend screen 4 Place o ring into recess Push o ring snugly against in line filter screen 5 Assemble nozzle extension to spray gun Snapper 2300 PSI Pressure Washer Cleaning Deter
6. 6 5 A 905944 5 B 9063265 C 190634GS D 938085 Snapper 2300 PSI Pressure Washer Description CAP Oil MANIFOLD PIN CAP THERMO RELIEF OIL BOTTLE not shown KIT UNLOADER STEM KIT WATER INLET ALUM KIT OUTLET ALUM KIT HEAD BRASS Item Part 193806GS 190592GS 190593GS 193807GS 189971GS 193971GS 193972GS A 12 6 gt SNAPPER Briggs amp Stratton POWER PRODUCTS Description KIT CHECK VALVES KIT INLET CHECK KIT CHEMICAL INJECTION KIT SEAL SET KIT CHEMICAL HOSE KIT PIPE FITTING KIT UNLOADER SEAT NOTE Item letters A L are service kits and include all parts shown within the box SNAPPER OWNER WARRANTY POLICY Effective January 1 2003 LIMITED WARRANTY This Snapper product is distributed under license to Briggs amp Stratton Power Products Briggs amp Stratton Power Products will repair or replace free of charge any part or parts of the equipment that are defective in material or workmanship or both Transportation charges on parts submitted for repair or replacement under this warranty must be borne by purchaser This warranty is effective for the time periods and subject to the conditions provided for in this policy For warranty service find your nearest Authorized service dealer by calling 1 800 317 7833 Warranty service may only be performed by a Briggs amp Stratton Power Products Authorized service dealer THER
7. E IS NO OTHER EXPRESS WARRANTY IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO THE TIME PERIOD SPECIFIED OR TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT EXCLUSION IS PERMITTED BY LAW Some countries or states do not allow limitations on how long an implied warranty lasts and some countries or states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation and exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from country to country or state to state WARRANTY PERIOD Pressure Washer 90 Days Portable Generator 2 Years 2nd year parts only The warranty period begins on the date of purchase by the first retail consumer or commercial end user and continues for the period of time stated in the table above Consumer use means personal residential household use by a retail consumer Commercial use means all other uses including use for commercial income producing or rental purposes Once equipment has been used commercially it shall thereafter be considered to be in commercial use for purposes of this warranty The engine and starting batteries are warranted solely by the manufacturers of those products WARRANTY REGISTRATIO
8. N IS NOT NECESSARY TO OBTAIN WARRANTY ON BRIGGS amp STRATTON POWER PRODUCTS EQUIPMENT SAVE YOUR PROOF OF PURCHASE RECEIPT IF YOU DO NOT PROVIDE PROOF OF THE INITIAL PURCHASE DATE AT THE TIME WARRANTY SERVICE IS REQUESTED THE MANUFACTURING DATE OF THE EQUIPMENT WILL BE USED TO DETERMINE THE WARRANTY PERIOD About your equipment warranty We welcome warranty repair and apologize to you for being inconvenienced Any Authorized service dealer may perform warranty repairs Most warranty repairs are handled routinely but sometimes requests for warranty service may not be appropriate For example warranty service would not apply if equipment damage occurred because of misuse lack of routine maintenance shipping handling warehousing or improper installation Similarly the warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered or modified During the warranty period the Authorized service dealer at its option will repair or replace any part that upon examination is found to be defective under normal use and service This warranty will not cover following repairs and equipment Normal Wear Outdoor power equipment like all mechanical devices needs periodic parts service and replacement to perform well This warranty does not cover repair when normal use has exhausted the life of a part or the equipment Installation and Maintenance This warranty does not apply to eq
9. PENAL by Briggs amp Stratton 2300PSI Stratton Pressure Washer AREER AA X COCA C CX Questions Help is just a moment away Helpline 1 800 317 7833 M F 8 5 CT This Snapper product is distributed under license to Briggs amp Stratton Power Products BRIGGS amp STRATTON POWER PRODUCTS GROUP LLC JEFFERSON WISCONSIN U S A 24847 07075 6 0 Model No 1807 1 2300 PSI Pressure Washer Manual No 193896GS Revision 0 09 30 2003 0 SNAPPER Briggs amp Stratton POWER PRODUCTS TABLE OF CONTENTS Safety Rules aout Soe 2 4 Know Your Pressure Washer 000 00000 eee 5 Assembly eek a bikes wet sepe te 7 6 7 Operatii erreen bd OR eR p Po tte 8 10 Product Specifications 0 cece E Maintenalice cese erp ete dae ave Rees 11 13 5661588 P ang cued ee 14 NOTES p pr 15 16 Troubleshooting serre mk 17 Replacement Parts 0 0 eee eee eee 18 19 Warranty i wea bute Last Page EQUIPMENT DESCRIPTION Read this manual carefully and become familiar LII with your pressure washer Know its applications it
10. Provide adequate water flow Straighten inlet hose patch leak Check and clean inlet hose strainer Provide cooler water supply Clear blocks in outlet hose Replace gun Clean nozzle Contact Snapper service facility Insert detergent siphoning tube into detergent Clean or replace filter detergent siphoning tube See Check In Line Filter on page 12 Push nozzle forward for low pressure mode Move throttle control to FAST position If engine still bogs down contact Briggs and Stratton service facility Pressure washer shuts down during operation Out of gasoline Fill fuel tank lt lt SNMAPPER Snapper 2300 PSI Pressure Washer by Briggs amp Stratton POWER PRODUCTS Item Part Description Item Part Description 192547GS BASE 10 21760GS ORIFICE 2 5 HANDLE I 192309GS KIT Hook 3 191909GS BILLBOARD 12 192050GS KIT E Ring 4 902495 HOSE 13 188792HGS WAND Adjustable Nozzle 5 192645GS KIT Pump Mounting Hardware I4 192311GS KIT Wheel 6 192128GS KIT Hook 15 23139GS KEY 7 190132GS GUN 16 193568GS ASSY Pump see page 19 8 B2203GS KIT Handle Connector 900 NSP ENGINE 9 192310GS KIT Vibration Mount Items Not Illustrated Part Description 193896GS MANUAL Owner s MS6847 MANUAL Engine 192548GS KIT Decal BB306IBGS OIL Engine 191922GS KIT O Ring Maint 8 NZZL CLNNG Item Part 19 190571GS 28 190627GS 45 190578GS 62 190581GS 76 21783GS 77 9058
11. WER PRODUCTS 2 Use a 8mm allen wrench to remove black pump oil cap between high pressure outlet and garden hose inlet Figure 15 Figure 15 Changing Pump Oil 3 Tilt pressure washer to drain oil into an approved container until it drips slowly from pump 4 Tilt pressure washer in opposite direction and empty premeasured pump oil bottle into same opening a small funnel may be helpful 5 Install black pump oil cap and tighten firmly 6 Set pressure washer in upright position Add fuel and engine oil ENGINE MAINTENANCE See the engine owner s manual for instructions on how to properly maintain the engine Avoid prolonged or repeated skin contact with used motor oil Used motor oil has been shown to cause skin cancer in certain laboratory animals Thoroughly wash exposed areas with soap and water KEEP OUT OF REACH OF CHILDREN DON T POLLUTE CONSERVE RESOURCES RETURN USED OIL TO COLLECTION CENTERS SNAPPER by Briggs amp Stratton POWER PRODUCTS PREPARING THE UNIT FOR STORAGE Water should not remain in the unit for long periods of time Sediments or minerals can deposit on pump parts and freeze pump action If you do not plan to use the pressure washer for more than 30 days follow this procedure Flush detergent siphoning tube by placing the filter into a pail of clean water while running pressure washer in low pressure mode adjustable nozzle in the forward positio
12. anty does not cover items that have been subjected to operator abuse or negligence To receive full value from the warranty the operator must maintain the pressure washer as instructed in this manual Some adjustments will need to be made periodically to properly maintain your pressure washer All maintenance in this manual and the engine owner s manual should be made at least once each season Once a year you should clean or replace the spark plug clean or replace the air filter and check the spray gun and adjustable nozzle extension assembly for wear A new spark plug and clean air filter assure proper fuel air mixture and help your engine run better and last longer Please refer to your engine owner s manual for more details If equipped with inflatable tires keep the air pressure at the value marked on the tire or within 15 and 40 psi Before Each Use Check engine oil level Check water inlet screen for damage Check in line filter for damage Check high pressure hose for leaks Check detergent siphoning tube and filter for damage Check spray gun and adjustable nozzle extension assembly for leaks Rinse out garden hose to flush out debris Snapper 2300 PSI Pressure Washer SNAPPER Briggs amp Stratton POWER PRODUCTS PRESSURE WASHER MAINTENANCE Check and Clean Inlet Screen Examine the screen on the water inlet Clean it if the screen is clogged or replace it if screen is damaged
13. asher 3 Apply a high pressure spray to a small area then check the surface for damage If no damage is found it is okay to continue cleaning A WARNING High pressure spray could cause you to fall if you are too close to the cleaning surface Keep spray nozzle between 8 to 24 inches away from cleaning surface Operate this unit on a stable surface Be extremely careful if you must use the pressure washer from a ladder scaffolding or any other relatively unstable location Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back 4 Start at top of area to be rinsed working down with same overlapping strokes as you used for washing and applying detergent Automatic Cool Down System Thermal Relief If you run the engine on your pressure washer for 3 5 minutes without pressing the trigger on the spray gun circulating water in the pump can reach temperatures above 2578 The system engages to cool the pump by discharging the warm water onto the ground MAINTENANCE SPECIFICATIONS Outlet Pressure 2300 psi Flow Rate 2 0 gallons per minute gpm Detergent Use detergent approved for pressure washers Water Supply Not to Exceed Temperature Automatic Cool Will cycle when water reaches 125 155 F 64 lbs Down System Shipping Weight GENERAL MAINTENANCE RECOMMENDATIONS The pressure washer warr
14. between 30 to 60 seconds Turn adjustable nozzle extension to stream spray and move nozzle from low to high while flushing Figure 14 Backflushing the Nozzle 6 Reinstall orifice and in line filter into nozzle extension DO NOT overtighten orifice with allen wrench 7 Reconnect nozzle extension to spray gun 8 Reconnect water supply turn on water and start engine 9 Test pressure washer by operating with nozzle in high and low positions O Ring Maintenance Through the normal operation of your pressure washer o rings are used to keep the connections of the hoses and spray gun tight and leak free These o rings may become worn or damaged An O Ring Maintenance Kit is provided with your pressure washer It includes replacement o rings rubber washer and water inlet filter Refer to the instruction sheet provided in the kit to service your unit s o rings Note that you will not use all of the parts in the kit To remove a worn or damaged o ring use a small flathead screwdriver to get underneath the o ring and pry it off Pump Maintenance Changing Pump Oil Change oil every 50 hours or once yearly whichever occurs first NOTE Purchase a premeasured bottle of pump oil item number 90586 65 by contacting the nearest authorized service center Change pump oil as follows l Drain engine oil and fuel from pressure washer Snapper 2300 PSI Pressure Washer SNAPPER Briggs amp Stratton PO
15. e other end to spray gun High Pressure Outlet Connection for pressure hose Nozzle Extension Attach to spray gun to use adjustable nozzle Oil Fill Cap Dipstick Used for checking and adding oil Pump Develops high pressure Recoil Starter Used for starting the engine manually Spray Gun Controls the application of water onto cleaning surface with trigger device Includes safety latch Water Inlet Connection for garden hose SNAPPER by Briggs amp Stratton POWER PRODUCTS ASSEMBLY IMPORTANT Read entire owner s manual before you attempt to assemble or operate your new pressure washer Remove Pressure Washer from Carton Remove parts bag included with pressure washer Slice two corners at end of carton from top to bottom so panel can be folded down flat then remove all packing material Remove pressure washer from carton Carton Contents Check all contents Main unit Engine Oil Safety Goggles High Pressure Hose Spray Gun Nozzle Extension e Parts Bag which includes the following Owner s Manual Engine Manual Owners Registration Card Maintenance Kit Handle Fastening Hardware Kit which includes Carriage Bolts 2 e Plastic Knobs 2 L Hooks 2 Lock Nuts 2 PREPARING PRESSURE WASHER FOR USE If you have any problems with the assembly of your pressure washer or if parts are missing or damaged call the pressure washer helpl
16. e washer from a ladder scaffolding or any other relatively unstable location Firmly grasp spray gun with both hands when using high pressure spray to avoid injury if gun kicks back Snapper 2300 PSI Pressure Washer by Briggs amp Stratton POWER PRODUCTS A WARNING Lk Fuel and its vapors are extremely flammable and explosive Fire or explosion can cause severe burns or WHEN ADDING FUEL Turn pressure washer OFF and let it cool at least 2 minutes before removing gas cap Fill fuel tank outdoors DO NOT overfill tank Allow space for fuel expansion Keep fuel away from sparks open flames pilot lights heat and other ignition sources DO NOT light a cigarette or smoke WHEN OPERATING EQUIPMENT DO NOT tip engine or equipment at angle which causes fuel to spill DO NOT spray flammable liquids WHEN TRANSPORTING OR REPAIRING EQUIPMENT Transport repair with fuel tank EMPTY or with fuel shutoff valve OFF WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK Store away from furnaces stoves water heaters clothes dryers or other appliances that have pilot light or other ignition source because they can ignite fuel vapors A WARNING The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues leading to serious injury and possible amputation NEVER aim spray gun at people animals or plants DO NOT allow CHILDREN to operate pressure washer
17. er 2300 PSI Pressure Washer SNAPPER Briggs amp Stratton POWER PRODUCTS KNOW YOUR PRESSURE WASHER Read this owner s manual and safety rules before operating your pressure washer Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and adjustments Save this manual for future reference Spray Gun Recoil Starter Nozzle Extension Pump equipped with Automatic Cool Down System Adjustable Nozzle Always attached to nozzle extension Adjustable nozzle allows you to adjust force of spray and spray pattern Air Cleaner Dry type filter element limits the amount of dirt and dust that gets in the engine Automatic Cool Down System Cycles water through pump when water reaches 25 155 F Warm water will discharge from pump onto ground This system prevents internal pump damage Chemical Injection Siphon Filter Use to siphon detergent or other pressure washer chemicals into the low pressure stream Data Tag not shown near rear of base plate Provides model revision and serial number of pressure washer Please have these readily available if calling for assistance Dr High Pressure Hose Oil Fill Cap Dipstick roc A Chemical Injection Siphon Filter Le High Pressure Outlet amp Water Inlet Fuel Cap Fill with clean unleaded fuel here High Pressure Hose Connect one end to water pump and th
18. gent Siphoning Tube If you used the chemical injection hose you must flush it with clean water before stopping the engine I Place chemical injection hose in a bucket full of clean water 2 Slide adjustable nozzle forward to low pressure position Flush for l 2 minutes 3 Shut off engine IMPORTANT Simply shutting OFF engine will not release pressure in the system When the engine has shut down squeeze the trigger on the spray gun to relieve the pressure in the hose Nozzle Maintenance A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure The principal cause of excessive pump pressure is a orifice clogged or restricted with foreign materials such as dirt etc To correct the problem immediately clean the orifice using the tools included with your pressure washer and follow these instructions Shut off engine and turn off water supply 2 Detach nozzle extension from spray gun Twist nozzle clockwise to stream position Using supplied 2mm 5 64 allen wrench remove orifice from end of nozzle extension Figure 13 I 3 Remove in line filter from other end of nozzle extension 4 Use wire included in kit or a small paper clip to free any foreign material clogging or restricting orifice Figure 13 MAINTENANCE 5 Using a garden hose remove additional debris by back flushing water through nozzle extension Figure 4 Back flush
19. high pressure spray which increases risk of injury and damage to unit DO NOT secure spray gun in open position DO NOT leave spray gun unattended while machine is running NEVER use a spray gun which does not have a trigger lock or trigger guard in place and in working order Always be certain spray gun nozzles and accessories are correctly attached CAUTION High pressure spray may damage fragile items including glass DO NOT point spray gun at glass when in jet spray mode NEVER aim spray gun at plants CAUTION Improper treatment of pressure washer can damage it and shorten its life If you have questions about intended use ask dealer or contact Snapper NEVER operate units with broken or missing parts or without protective housing or covers DO NOT by pass any safety device on this machine Before starting pressure washer in cold weather check all parts of the equipment to be sure ice has not formed there NEVER move machine by pulling on high pressure hose Use handle provided on unit Check fuel system for leaks or signs of deterioration such as chafed or spongy hose loose or missing clamps or damaged tank or cap Correct all defects before operating pressure washer This equipment is designed to be used with Briggs amp Stratton Power Products authorized parts ONLY If equipment is used with parts that DO NOT comply with minimum specifications user assumes all risks and liabilities Snapp
20. ide nozzle forward and squeeze trigger on spray gun to relieve pressure caused by turning ON water Water will flow out of gun in a thin stream Continue to hold trigger until there is a steady stream of water and no air remains in system Release trigger 8 Engage safety latch to spray gun trigger Figure 8 Figure 8 Spray Gun with Safety Latch Engaged Safety Latch AN 7 9 Start engine according to instructions given in engine owner s manual NOTE If the recoil starter is hard to pull it may be necessary to squeeze the gun trigger to relieve internal pump pressure CAUTION Avoid injury from kickback Squeeze trigger on spray gun each time recoil starter is pulled and engine fails to start How to Stop Your Pressure Washer Let the engine idle for two minutes Turn engine off according to instructions given in the engine owner s manual Squeeze trigger on the spray gun to relieve pressure in the hose NOTE A small amount of water will squirt out when you release the pressure Snapper 2300 PSI Pressure Washer SNAPPER by Briggs amp Stratton POWER PRODUCTS How to Use Adjustable Nozzle 3 Twisting nozzle adjusts spray pattern from a narrow You should now know how to START and STOP your parem to a far pattern ewe pressure washer The information in this section will tell Figure I Adjusting the Nozzle for Spray Pattern you how to adj
21. ine at 1 800 317 7833 If calling for assistance please have model revision and serial number from data tag available To prepare your pressure washer for operation you will need to perform these tasks Fill out and send in registration card Snapper 2300 PSI Pressure Washer Add oil to engine crankcase Add fuel to fuel tank Connect high pressure hose to spray gun and pump Connect water supply to pump nu hwnd Attach nozzle extension to spray gun Attach Handle Place handle assembly onto handle supports connected to main unit Make sure holes in handle align with holes on handle supports Figure 1 Figure Attach Handle to Base Handle Align Holes Handle Supports NOTE It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports 2 Insert carriage bolts through holes from outside of unit and attach a plastic knob from inside of unit Figure 2 Tighten by hand Figure 2 Secure Handle 3 Insert one L hook through hole just under billboard on left side of handle viewing from rear of unit Hold hook in place with pliers and attach locknut with a 7 16 wrench Figure 3 Figure 3 Attach L Hooks to Handle Hose Hook Snapper 2300 PSI Pressure Washer SNAPPER 6 Briggs amp Stratton 4 Insert other L hook through hole just above 3 Before connecting garden hose
22. lable draw RV antifreeze non alcohol into the pump by pouring the solution into a 3 foot section of garden hose connected to inlet adapter and pulling recoil handle twice STORING THE ENGINE See the engine owner s manual for instructions on how to properly prepare the engine for storage Snapper 2300 PSI Pressure Washer 6 SNAPPER b us Scu NOTES amp SNAPPER Snapper 2300 PSI Pressure Washer b o um n NOTES TROUBLE SHOOTING TROUBLESHOOTING Problem Cause Snapper 2300 PSI Pressure Washer SNAPPER by Briggs amp Stratton POWER PRODUCTS Correction Pump has following problems failure to produce pressure erratic pressure chattering loss of pressure low water volume Detergent fails to mix with spray Engine runs good at no load but bogs when load is added Nozzle in low pressure mode 2 Water inlet is blocked 3 Inadequate water supply 4 Inlet hose is kinked or leaking 5 Clogged inlet hose strainer 6 Water supply is over 100 F 7 High pressure hose is blocked or leaks 8 Gun leaks 9 Nozzle is obstructed 10 Pump is faulty Detergent siphoning tube is not submerged 2 Chemical filter is clogged or cracked 3 Dirty in line filter 4 Nozzle is in high pressure mode Engine speed is too slow EU ds Pull nozzle backward for high pressure mode Clear inlet
23. n Flush for one to two minutes 2 Shut off the engine and let it cool then remove high pressure and garden hoses Disconnect spark plug wire from spark plug 3 Empty the pump of all pumped liquids by pulling the recoil handle about 6 times This should remove most of the liquid in the pump 4 Use PumpSaver to prevent corrosion build up and freezing of pump 5 Store unit in a clean dry area Protecting the Pump To protect the pump from damage caused by mineral deposits or freezing use PumpSaver to treat pump This prevents freeze damage and lubricates pistons and seals Snapper 2300 PSI Pressure Washer NOTE PumpSaver is available as an optional accessory It is not included with the pressure washer Contact the nearest authorized service center to purchase PumpSaver CAUTION You must protect your unit from freezing temperatures Failure to do so will permanently damage your pump and render your unit inoperable Freeze damage is not covered under warranty A CAUTION Read and follow all cautions and warnings on the PumpSaver can label Always wear eye protection when using PumpSaver To use PumpSaver make sure the pressure washer is turned off and disconnected from supply water Read and follow all instructions and warnings given on the PumpSaver container NOTE PumpSaver will drip from pump after treatment and will stain wood and concrete NOTE If PumpSaver is not avai
24. s limitations and any hazards involved Every effort has been made to ensure that information in this manual is accurate and current However we reserve the right to change alter or otherwise improve the product and this document at any time without prior notice In the State of California a spark arrester is required by law Section 4442 of the California Public Resources Code Other states may have similar laws Federal laws apply on federal lands If you equip the muffler with a spark arrester it must be maintained in effective working order Snapper 2300 PSI Pressure Washer SAFETY RULES SAFETY RULES This is the safety alert symbol It is used to A alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death The safety alert symbol is used with a signal word DANGER CAUTION WARNING a pictorial and or a safety message to alert you to hazards DANGER indicates a hazard which if not avoided will result in death or serious injury WARNING indicates a hazard which if not avoided could result in death or serious injury CAUTION indicates a hazard which if not avoided might result in minor or moderate injury CAUTION when used without the alert symbol indicates a situation that could result in equipment damage Follow safety messages to avoid or reduce the risk of injury or death The engine exhaust from this product contains chemicals known to
25. the State of California to cause cancer birth defects or other reproductive harm Hazard Symbols and Meanings Toxic Fumes Electrical Shock gt 59 8 am effe Slippery Surface Fall Fluid Injection oS WS Fire Explosion Hot Surface oe Flying Objects Kickback Moving Parts A DANGER Running engine gives off carbon monoxide an odorless colorless poison gas Some chemicals or detergents may be harmful if inhaled or ingested causing severe nausea fainting or poisoning Breathing carbon monoxide will cause nausea fainting or death Operate pressure washer ONLY outdoors Use a respirator or mask whenever there is a chance that vapors may be inhaled Read all instructions with mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors A WARNING WY Spray contact with electrical wiring can result in vw electrocution Keep water spray away from electric wiring or fatal electric shock may result A WARNING Use of pressure washer can create puddles and slippery surfaces High pressure spray could cause you to fall if you are too close to the cleaning surface Keep spray nozzle between 8 to 24 inches away from cleaning surface Operate this unit on a stable surface The cleaning area should have adequate slopes and drainage to reduce the possibility of a fall due to slippery surfaces Be extremely careful if you must use the pressur
26. to high pressure hose Provide a proper water supply at an adequate flow Be sure to read Safety Rules and How To Use Your Pressure Washer before using pressure washer HOW TO USEYOUR PRESSURE WASHER If you have any problems operating your pressure washer please call the pressure washer helpline at 1 800 317 7833 How to Start Your Pressure Washer To start your pressure washer for the first time follow these instructions step by step This starting information also applies if you have let the pressure washer sit idle for at least a day Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3 0 gallons per minute and no less than 20 PSI at pressure washer end of garden hose 2 Check that high pressure hose is connected to spray gun and pump See Preparing Pressure Washer for Use for illustrations Make sure unit is in a level position 4 Connect garden hose to water inlet on pressure washer pump Turn ON the water 5 Squeeze trigger on gun until you have a steady stream of water This purges the pump of air and impurities CAUTION DO NOT run the pump without the water supply connected and turned on Damage to equipment resulting from failure to follow this instruction will void warranty Snapper 2300 PSI Pressure Washer 6 Attach nozzle extension to spray gun Figure 7 Tighten by hand 7 Position nozzle in low pressure mode sl
27. to water inlet inspect billboard on right side of handle viewing from rear of inlet screen Figure 6 Clean screen if it contains unit Hold hook in place with pliers and attach locknut debris or have it replaced if damaged DO NOT RUN with 7 16 wrench Figure 3 PRESSURE WASHER IF SCREEN IS DAMAGED Figure 6 Connect the Garden Hose to Water Inlet Add Engine Oil and Fuel Inspect inlet Place pressure washer on a level surface screen DO NOT use if damaged clean if dirty CAUTION Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure Refer to engine manual for oil and fuel fill information Damage to equipment resulting from failure to follow this instruction will void warranty 4 Run water through garden hose for 30 seconds to clean out any debris Turn off water Refer to engine owner s manual and follow oil and fuel recommendations and instructions IMPORTANT DO NOT siphon standing water for the NOTE Check oil often during engine break in Refer to Water supply Mss ONLY gold water less than 10071 engine owner s manual for recommendations 5 Connect garden hose not to exceed 50 feet in length to water inlet Tighten by hand Figure 6 CAUTION There MUST be at least ten feet of unrestricted garden IMPORTANT To avoid pump damage you must assemble hose between the pressure washer inlet and any flow
28. uipment or parts that have been subjected to improper or unauthorized installation or alteration and modification misuse negligence accident overloading overspeeding improper maintenance repair or storage so as in our judgment to adversely affect its performance and reliability This warranty also does not cover normal maintenance such as adjustments fuel system cleaning and obstruction due to chemical dirt carbon or lime etc Other Exclusions Also excluded from this warranty are wear items such as quick couplers oil gauges belts o rings filters pump packing etc pumps which have been run without water supplied or damage or malfunctions resulting from accidents abuse modifications alterations or improper servicing or freezing or chemical deterioration Accessory parts such as guns hoses wands and nozzles are excluded from the product warranty Also excluded is used reconditioned and demonstration equipment equipment used for prime power in place of utility power and equipment used in life support applications BRIGGS amp STRATTON POWER PRODUCTS GROUP LLC JEFFERSON WISCONSIN U S A
29. ust the spray pattern and to apply detergent or other cleaning chemicals l Slide nozzle forward when you wish to adjust spray to low pressure mode Figure 9 Slide nozzle backward to achieve high pressure Figure 9 Adjusting Nozzle for Pressure Rotate nozzle Rotate nozzle clockwise counterclockwise for fan for narrow spray pattern spray pattern 4 For most effective cleaning keep spray nozzle from 8 to 24 inches away from cleaning surface 5 If you get spray nozzle too close especially using high Slide nozzle backward Slide nozzle forward for low pressure mode you may damage surface being cleaned for High Pressure pressure mode and Mode detergent application 2 Point nozzle down towards a firm surface and press Applying Detergent with the trigger to test spray pattern Figure 10 Adi justable Nozzle IMPORTANT Use soaps designed specifically for pressure washers Household detergents could damage the pump CAUTION You must attach all hoses before you start the engine 6 DO NOT get closer than 6 inches when cleaning tires Figure 10 Testing the Spray Pattern 1 Starting the engine without all the hoses connected and without the water turned ON will damage the pump Damage to equipment resulting from failure to follow this instruction will void warranty To apply detergent follow these steps I Review use of adjustable nozzles 2 Prepare detergent solution as required by job
Download Pdf Manuals
Related Search