Siemens SC9000 User's Manual
Contents
1. ey EE 3875 Cypress Drive Petaluma CA 94954 800 228 2555 707 773 1100 Fax 707 773 1180 www gcx com MSTRUMENT MOUNTING SYSTEMS GCX Mounting Assembly Operation Installation Manual Drager Model Cato with Siemens SC9000 Patient Monitor Patient Monitor Left Side on Pivot Arm Power Supply on Right Side The purpose of these instructions is to 1 Describe attachment of GCX mounting hardware to the Cato anesthesia machine 2 Describe attachment of the Siemens monitor to the GCX mounting hardware WARNING USE OF MOUNTING HARDWARE AND MONITORING COMPONENTS OTHER THAN THOSE DESCRIBED IN THIS DOCUMENT MAY RESULT IN SERIOUS INJURY DUE TO TIPPING OF THE ANESTHESIA MACHINE THIS CATO MOUNTING CONFIGURATION REQUIRES THE 40KG COUNTERWEIGHT WITH EXTENDED WHEEL ADAPTER UPGRADE SET FROM DRAGER PART NUMBER 86 018 68 Installer When installation is completed provide these instructions to the end user for future reference INSTALLATION Tools Required Philips head screw driver Hex key incl Accessory Track gt Mounting the Channel to Cato Edition Parts Required 4 Channel M6 x 16 mm FHMS screws 2 Brass Plate with inserts from Drager M29110 1 To attach the Channel to the Cato left side accessory track eter locate the brass plate in the accessory track align the mounting holes in the Channel with the threaded holes on the brass plate then run the M5 flat head screws 2 partly in Note Fixed Stop is at the bott2. with edge of the Channel insert into channel DU DR 0016 SC9000 Rev A 6 4 02 GCX Corp Page 2 of 4 INSTRUCTIONS FOR USE M Series Pivot Arm Pivot 1 To pivot the Arm near the wall simply push on the side of the Arm or mounted device 2 To adjust the pivot tension at the Slide use a 7 or 13mm socket driver to tighten or loosen the Pivot Tension Bolt to obtain the desired tension Pivot Arm Swivel Tension Bolt Pivot Tension Bolt Swivel 1 To rotate the device simply push or pull the corners of the device 2 To adjust the swivel tension use a 72 or 13mm socket driver to tighten or loosen the Swivel Tension Adjustment Bolt located under the front end of the Arm Tilt 1 Grasp the top and bottom of the device and tilt it to the desired angle 2 To adjust the overall tilt tension evenly tighten or loosen the 2 10 32 x 5 8 SHCS Tilt Tension Adjustment Screws using the supplied 5 32 4 mm hex key Cable Management 1 An open cavity beneath the arm with flexible cable covers manage cables going to and from the front and rear of the arm Flexible Cable Covers Rev A 6 4 02 GCX Corp Page 3 of 4 Cleaning 1 The mounting assembly may be cleaned with most mild non abrasive solutions commonly used in the hospital environment e g diluted bleach ammonia or alcohol solutions 2 The surface finish will be permanently damaged by strong chemicals and solvents such as acetone and trichl
3. om of the Channel 2 Set the height of the Channel in the accessory track and tighten the M6 screws to hold in place aaa Prepare M Series Arm 1 Install the Tilt Limiting Stop screw a AENT l DU DR 0016 SC9000 Rev A 6 4 02 GCX Corp Page 1 of 4 Install M Series Arm 1 The Slide has 2 20 x 3 4 SHSS set screws that when tightened secure the Arm at the desired location within the Channel 2 While supporting the bottom of the Arm with one hand guide the Slide at the rear of the arm into the top of the Channel 3 Once the Arm is at the desired height tighten both set screws using the supplied 1 8 3 mm hex key Slide Pick amp Go Base into Mounting Plate 1 Align the mounting adapter located at the bottom of the Pick amp Go base with the edge of Mounting Plate Slide the Pick amp Go base into the plate until it stops at the Spring Plunger located below the Mounting Plate Pull the Spring Plunger and continue to slide the base until the mounting adapter engages the Spring Plunger Tighten the 4 nylon thumb screws on the back of the Mounting Plate Install 4 Cato Channel on Right Side As described on Page 1 of this document Install Power Supply Mounting Adapter to Siemens Power Supply Mount Siemens P N 4720129 1 Install according to the instructions included with the adapter Slide Power Supply Mount into Channel amp Insert Power Supply 1 Align the Slide of the mount
4. oroethylene 3 Steel wool or other abrasive material should never be used 4 Damage caused by the use of unapproved substances or processes will not be warranted To verify compatibility It is recommended that any cleaning solution be tested on a small area of the arm that is not visible 5 Never submerge the mounting arm Wipe any cleaning agents off of the arm immediately using a water dampened cloth Dry the arm thoroughly after cleaning CAUTION GCX makes no claims regarding the efficacy of the listed chemicals or processes as a means for controlling infection Consult your hospital s infection control officer or epidemiologist To clean or sterilize mounted devices or accessory equipment refer to the specific instructions supplied with those products PARTS LIST GCX P N Drager P N DESCRIPTION WMM 0002 02 MM15278 12 M Series Pivot Arm DR 0017 82 MM15719 4 Cato Channel 2 M29110 Accessory Track Brass Plate Drager Power Supply Right Side CPS GCX P N Siemens P N Drager P N DESCRIPTION 4720129 Siemens Power Supply Holster Siemens Power Supply Flush Mount for nadia Es Siemens P N 4720129 pe MM15719 4 Channel w T Nuts Fe M29110 Accessory Track Brass Plate Drager DR 0017 82 as DU DR 0016 SC9000 Rev A 6 4 02 GCX Corp Page 4 of 4
Download Pdf Manuals
Related Search