Q-See QSE7F4 Technical Manual
Contents
1. against the door frame which prevents the door from being opened simply by inserting something like credit card 13 Standalone suitable for office meeting room residence etc 1 2 Size amp Weight 1 2 1 Lock size Unit mm 69 2 lt P 1 2 3 Weight Parts Net Weight Front plate 2 58 1b Back plate 3 44 lb Mortise 2 12 Ib Total 8 14 Ib V ee OSE7F4 USER MANUAL 1 3 1 Technical Parameters No Item Fingerprint sensor Sensor resolution Antistrike ability of sensor surface Authentication speed Authentication methods FRR FAR Angle for putting finger Fingerprint scanning Fingerprint template saved User capacity Light jam Sensor surface Operating voltage Battery life Temperature for storage Static current Dynamic current Technical parameters Optical sensor CMOS 0 3 Mega Pixel 500 dpi Remain good condition after being jabbed with a 4H pencil at a 20cm s distance lt 1 second 1 N lt 1 lt 0 0001 360 Twice to get one fingerprint template All enrolled fingerprint template will be saved while replacing the batteries 120 max Sunlight resistable Optical glass with PVD coated 4 AA alkaline batteries DC 4 5 6 0v or a 9V stand by battery Approx 12 months 10 C 50 C lt 40 uA lt 180mA O See QSE 7F4 USER MANUAL 1 3 2 Operating Environment Outdoor Temperature 8C 50 C Indoor Temperature 5C 50 C Humidit2. ee OSE7F4 USER MANUAL 2 Lock out status locked with latchesand deadbolt Figure 2 2 Button 1 TO ENROLLGROUP MEMBER S FINGERPRINT S Button 2 TO ERASEGROUP MEMBER S FINGERPRINT S Button 3 TO SET THE LOCK INTO NORMALLY OPEN STATUS 2 5 Master fingerprint amp Emergency PIN 2 5 1 Howto set Master fingerprint 1 Press andhold the cylindercover button slidedown the cylindercover with another hand Figure 2 3 2 2 3 Normally open status the lock will always beunlocked by rotating outside lever 2 3 Instruction for indicators 1 Green light flashes once followed by a long beep it means successful operation 2 Insert mechanical key into the keyhole turn the key anticlockwise if left 2 Red light flashes once followed by 2 short beeps it means failed handed lock clockwise if right handed lock till along beef is heard stop operation turning and hold the key Red and green light flash red light on sensor 3 Red lightflashes from the sensor itmeans the sensoris working flashes as well which means the lock is ready for setup Figure 2 4 4 Red and green light flash the buzzer alert3 times itmeans low voltage please change the batteries 5 Red light flashes once the buzzer alert once it means the fingerprint number is already used use adifferent number 6 Green light flashes once asecond it means the lock isin normally open Status 7 Red lightflashes once asecond it means
3. SE 424515 peri ha RR EE RR Dk ei ede ees ed ROER eN DE DA Banc on Or TO RE RR EE EN 2 5 Master fingerprint amp Emergency PIN issue ELKE RA es EE Se Eg 2 5 1 How toset Master fingerprint me he EE OE NO ON 2 5 2 How toset Emergency PIN iii creer ee ee EE EE EE Ee ee ee ee 2 6 Enroll erase group member s fingerprint s sies DEE REEDE AE RE tee ees 2 6 1 Enroll group member s fingerprint s rererere EE ee ee ee ee eer 2 6 2 How toerase group member fingerprint see EE EE EE Ee er 15 GRIET ER EE EE 15 27 1 OiloekithEaierseaes PIN s1 lt e c28e lt 2gerersg uate esepecceintoneet 15 2 7 2 Unlock with group member fingerprint esse eee 16 2 7 3 Unlock withmechanical key iis BREEDERS EG AG 17 2 8 How toset the statusof the lock EE Ge eben ete en ene ees 17 EE od AA OO OE N EE OE 17 2 8 2 Lock out oe il AR OO AO DE ER N E EEEE 17 283 Normally open Stattis ses oe DE EE GEE RENE Ge RE ig E 18 29 Change batteries sees be BE OE DS EE ER EG deed DAG AE PD tite rs 19 ME Ee IE De ER N OE N OE EE OE EE 20 BA Door rogo eA EERDER EE er OE GR ge EE Ee Ep aS 20 39 Toole Teqiired oi sok ERG Os DEE Ee ei Ge die de ARE Deli EE sc 20 3 3 Installation template mense ER tenet ages ER ee ee eo 21 E e ET a9 A IWATE EE EN OE EE cee elec ede 24 4 Daly tai PIE mene se RR DE DE GEE EE RR EE AD Re HD 24 Ge ei ed ARE EE EN 24 00 id HER OE ee EER 25 5 1 Package Contents iss EER EERDER EN EER EN EER EE RE EE Nee ER EN EN GE EEN ENE 25 5
4. keypad 5 Each lockhas only ONE Master fingerprint Emergency PIN 6 To change Master fingerprint or Emergency PIN just set a new Master fingerprint or input a new Emergency PIN After the new Master fingerprint is setup successfully the fingerprints authorized by old Master fingerprint become invalid automatically 7 Master fingerprint can only be used to authorize to enroll group member s fingerprints but cannotbe used toopen the lock 8 Emergency PIN is theonly PIN toopen the lock 11 12 V ee OSE7F4 USER MANUAL Fingerprint number amp name list Group A Group B Group C Group D No Fingerprint Fingerprint Fingerprint Fingerprint Name Name Name Name No No No No a oon oor oo o a ma ms ma Go o oor 1021 Pio foo i02 20227 a foo ios 2023 Pia 0030 f 1030 2030 rs oor rosies Pia ose tos 2032 _ MEE EER Er AE NE 302 302 303 303 303 3100 3101 3102 3103 3110 ESE 2112 3113 312 Oo GUY Go ee N DEMP gt S Pas oo mo o oo N foa ar pa er rao fo ne ha o ID For deleting Group A ID For deleting Group B ID For deleting Group C ID For deleting Group D 0000 1000 2000 3000 09 NO Dal Q Seeg QSE7F4 USER MANUAL Referring to thelist let s takethe member in Group A Fingerprint No 0001 for example 2 6 1 Enroll group member s fingerprint s 1 Place Master finger on the sensor the lock will be activated once
5. 9 Handle Orientation rererere reien En DES BERE EE WEE ES EES GEEN Ge GE Ee 26 5 3 Fingerprint number amp name list EER ET ER RE AT EE nls ge ea 27 O See QSE 7F4 USER MANUAL 1 Introduction 1 1 Features 1 1 1Model number Fingerprint Plus Keypad amp Deadbolt Lock Image Model QSE7F4 Color polished gold edge pearl chrome 1 1 2 Main features 1 Optical sensor with high resolution 500 dpi 2 5 latches higher security 3 3 waysto open Fingerprint PIN and mechanical keys 4 Capacity maximum 120 fingerprints ind groups 5 Allowto erase single fingerprint or group fingerprints 6 Fingerprint can be enrolled and erased on the lock directly no PC connection required 7 Deadbolt canbe locked byrotating outside inside lever V ee OSE7F4 USER MANUAL V ee OSE7F4 USER MANUAL 8 Blue backgroundlight convenient fornight use 1 2 2 Mortise size 9 Normally open status can beset for meetings or events Unit mm 10 Operates ond AAalkaline batteries ora 9V battery with low voltage alert 11 Auto alarm function If the door is not locked properly the latches draw out 3 seconds later the lock will alarm automatically While alarming the door can t be opened with fingerprint or Emergency PIN but can be opened with mechanical key after 1 minute s alarming the alarm stops the lock goback into normal status 12 Antistrike function when the door is closed the antistrike latchis pressed
6. AL 2 11 2 8 3 Normally open status None of the Emergency PIN Group member fingerprint and mechanical key is required just rotate the outside lever to open the door In this case the green indicator flashes once for a second Follow the under mentioned steps to set the lock into Normally open status 1 Unlock with Emergency PIN or group member fingerprint till you hear the motor activated donot rotate the outside lever Figure2 12 2 12 2 Press button 3 until the blue background and green indicator light up and the buzzer sounds once and then release the button 3 The green indicator 18 2 9 Change batteries Ql See QSE7F4 USER MANUAL flashes once for a second which indicates the lock is set into Normally open status successfully 3 Unlock with Emergency PIN or group member fingerprint again after you hear the motoractivated the Normally open status is cancelled When the low voltage indicator turns on to ensure the normal use of your lock please change the batteries as soonas you canby following below steps 1 Press and hold the battery cover button slide down the battery cover Figure 2 13 2 Take out all batteries replace with 4 alkaline batteries and push back the battery cover Figure2 14 NOTE If the batteries are totally dead you can usea 9V alkaline battery not provided on socket for stand by power to activate the lock but remember to ch
7. TRADEMARKS All brand names and products are Registered Trademarks of their respective Companies LEGAL DISCLAIMER See warning on rear cover DISCLAIMER The information in the documentis subject to change without notice The manufacturer makes no representa tions or warranties with respect to the contents hereof and specifically disclaims any implied warranties of selling or functionality for any particular purpose Digital Peripheral Solutions Inc S015 E Crystal drive Anaheim CA 92807 1 877 998 3440 Q See tech supportin U S A Mon Fri 9 am 6pm PST TEL 1 877 998 3440 E mail ts dpsi usa com Website lt www q see com gt See Fingerprint Keypad amp Deadbolt Lock USER MANUAL MODEL No QSE 7F4 CONTENTS 1 Introduction oee eee OE OE N OE N EEEE RE Features eocen DA TOE HE OE EN rea ise deeds 1 1 1 Model number SEE RES RE ED GO RS ON eins DOER DS DE DE BE REDS 1 1 2 Mid Ee AA OR OO ORE N OE EG RAS OR OE N EE ER OE RAL TE ET OE ET EE N EER OIE N 123 EE EE OE N OR EE EE BEL TOE RA RE S 1 3 Technical Parameters AO NS RE EE EE ed 1 3 1 Technical Parameters ees ae are Re NEE ER eee net RR ie NG ae ee Oe 1 3 2 Operating EE So AE Ed EE Oe ET EE EE A LA Conponenig AE OE EE EE LS Structure Viei EE N EO N W 2 Operation Instruction EE EE EE ee EE ee EE Ee EE ee ee ee ee 2 1 Left handedand Right handed aie bie Ek sie EA ER 22 SE Rd re ee enh sGer OD AO EE EET OR OT DE ER OE 2 3 Instruction forindicators
8. ange the batteriesas soon as possible 19 20 V ee OSE7F4 USER MANUAL 3 Installation 3 1 Door requirement 1 Material of door wood 2 Thickness 40 65mm 3 If there is decorative part on the door the distance between door edge and Decorative part must not be less than 110mm 3 2 Tools required The following tools not provided aresuitable for installingthis lock y y N Drill bit Ipc File Knife Drill Square ruler Ipc Screwdriver Chisel Pencil Tape measure lpc Ipc Ipc lpc P A Ql See QSE7F4 USER MANUAL 3 3 Installation template b ee O O O O 14 te O O O q O D gt O 5 O wz LL N LL N O Lever centerline B Drilling view of door frame A Drilling view of door 21 22 V ee OSE7F4 USER MANUAL 3 4 Installation steps 1 Draw lever centerline as your request the recommended height is 1 meter above the ground Mark the door for drilling holes witha pencil according installation template provided 2 Drill the door from both sides with electric drill Cut out the cavity for mortise as per drilling view in the manual 4 Fix front plate on wee the door make the spindle on the front plate through the cylinder Mortise to Line Square spindle centerline Mortise Line 3Put the
9. ert mechanicalkey into thekeyhole turn thekey anticlockwise ifleft handed lock clockwise ifright handed lock till a long beep is heard stop turning Redand green light flash red light on sensor flashes as well which means the lock isready for setup Figure2 4 3 Input a8 digit PIN whose first digit should not be 0 followed bya long beep which indicates the first time successfulinput for Emergency PIN NOTE After entering the first digit all red indicators change to green indicator lights 4 Repeat entering the same 8 digit PIN green indicator goes out followed by a O See QSE 7F4 USER MANUAL long beep whichindicates the successfulsetup for Emergency PIN 5 After setting the Emergency PIN successfully turn the mechanical key to the original position anddraw out putthe cylinder coverback NOTE 1 While thelock is waiting for setup ifyou don t putthe finger orinput Emergency PIN the red light on sensor will go outafter 5 seconds flashing 2 Master fingerprintand Emergency PIN have tobe set separately 3 While setting the Emergency PIN the pause between 2 presses should not be longer than 4seconds meanwhile the pause between firstand second entering the 8 digit PIN should not be longer than 4 seconds either otherwise the red indicator flashes followed by2 short beepsto indicate the failed setup 4 Emergency PIN must be8 digits andthe first digitshould not be 0 other digits could be any of the 4buttons on the
10. gerprint number amp name list B To change cover Master fingerprint canerase ALLenrolled fingerprints 2 Unlocking 2 7 1 Unlock with Emergency PIN 1 Input correct8 digits Emergency PIN NOTE A Every time you input a number blue background will light up The pause between 2 presses should not be longer than4 seconds B If invalid PIN was entered 3 times continuously the button 1 2 3 will 15 16 V ee OSE7F4 USER MANUAL be locked Master fingerprint or group member fingerprint can cancel the locked status orthe locked status will be deletedin 1 minute automatically 2 Blue background and green indicator light up along beep is heard the inside motor is activated 3 Rotate the outside lever tounlock Figure2 9 2 9 2 7 2 Unlock with group member fingerprint 1 Place an enrolled group member finger on the sensor the lock is activated after the infrared detector detected the finger The blue background lights green indicator light and the red light in the sensor flashes or press 0 the blue background green indicator light and the red light in the sensor flashes place an enrolled group member fingeron the sensor NOTE If invalid finger was used 10 times continuously the sensor will be locked Master fingerprint or group member fingerprint can cancel the locked status or the locked status willbe deleted in 1 minute automatically 2 Green indicator flashes once and light
11. mortise into the mortise cavity fix it with 2 pcs of M4 25 Screws 5 Connect the data cable in front plate with back plate fix the back plate with 2 pes of M5 screws and Ipc of M6 screw Square spindle centerline E i O See QSE 7F4 USER MANUAL 6 Put 4 AA alkaline batteries in battery box as instructed 8 Testthe lock as per operation instructions 9 Cover the back screw hole with plastic screw cover provided 7 Mark the door frame for drilling holes as per drilling view Cut out the cavity for strike and strike plate Put strike into thecavity covered with strike plate fix themon the door frame with 3 pcs of M4 25 screws ee O em Q ee O 10 Installation completed 23 24 V ee OSE7F4 USER MANUAL 4 Maintenance A Keep away from corrosive material B Do not hang anything on the levers C Keep the sensor surface clean and dry Wipe it with soft and dry cloth if any stain on it D When the batteries are dying the red indicator flashes to alert low voltage Although you still can unlock the door 20 30 times you should replace the batteries as soon as possible E Keep the mechanical keys carefully to prevent from being burglarized 4 2 Troubleshooting When you put your enrolled fingerprint onto the sensor to unlock red indicator fla
12. rint Name Name Name Name No No No No oer o oo 300r 2 oo 1002 foo oo rs 0003 _ oos 2003 3003 r oof oie soe 3010 rs fof pon foo son soos ies sos 302 oase fos 0 2r
13. s up along beep is heard and the inside motor is activated 3 Rotate the outside lever tounlock Figure2 9 NOTE within 5 seconds after the inside motor is activated the outside lever must be rotated to unlock Otherwise the door will be locked again automatically O See QSE 7F4 USER MANUAL 2 7 3 Unlock with mechanical key 1 The same operation with step 1 in 2 5 1 2 Insert mechanical key into the keyhole turn the key anticlockwise if right handed lock clockwiseif left handedlock until itunlocks Figure2 10 2 10 3 Push thedoor to open 2 8 How to set the status of the lock In 2 2 we ve introduced Lock status Lock out status and Normally open status detailed explanation follows 2 8 1 Lock status If the lock is not in Lock out status or Normally open status it means that the lock is in lock status In this case if you are outside the room you can open with either of Emergency PIN Group member fingerprint or mechanical key if youare inside justrotate the insidelever to openthe door 2 8 2 Lock out status Rotate the outside inside lever toreach out the deadbolt and make the lock in Lock out status Figure2 11 In this case the red indicator flashes once a second If you are outside the room you can open with either of Emergency PIN Group member fingerprint or mechanicalkey if youare inside justrotate the inside leverto open the door 17 V ee OSE7F4 USER MANU
14. sensor when the red light in the sensor goes out move away the finger along beep isheard 7 When thered light onthe sensor flashes again place the same member finger on the sensor second time till a long beep is heard which indicates the successful enrollment ofthis member fingerprint NOTE A In the Fingerprint number amp Name list up to 120 group member fingerprints can be enrolled But since Fingerprint number 3132 is for Master fingerprint therefore actually 119 group member fingerprints can be enrolled in each lock B Master fingerprintand the groupmember fingerprint cannotbe the same C Afingerprint number willonly allow toenroll one fingerprint D Group member fingerprint can openthe lock O See QSE 7F4 USER MANUAL 2 6 2 Howto erase group member fingerprint 1 The same operation withthe steps land 2 in2 6 1 2 Press button 2 a longbeep is heard red indicator goes out green indicator lights Figure2 8 2 8 3 Input the fingerprint number you wish to erase here we take 0001 for example Input 0001 a long beep is heard which means the successful first input 4 Input 0001 again a long beep is heard and followed by another long beep green indicator goes out which means the successful erasing of fingerprint 0001 NOTE By following above steps if you input ID for deleting group for step 3 and 4 all fingerprints in the indicated group will be deleted Refer to Fin
15. shes and follows two short beeps door can t be opened When you put your valid enrolled fingerprint onto the sensor to unlock red indicator flashes and follows two short beeps door can t be opened 1 Invalid fingerprint key 2 Your fingerprint has already been deleted 1 Your fingerprint position is quite different from where you first enrolled 2 Bad quality fingerprint Unlock the door with a valid fingerprint key Put your finger onto the sensor again try to put it onto where you first enrolled Ql See QSE7F4 USER MANUAL 9 Appendix 5 1 Package Contents Key box contents Accessories bag contents 10 Item Front plate Back plate Mortise Key box Mechanical key Plastic screw cover AA alkaline battery Strike Strike plate Installation template A Installation template B Accessories bag Hexagon screw M6 X L Cincluding 1 pc for spare use Fixing screw M5 X L Cincluding 2 pcs for spare use Hexagon screwdriver Tapping screw M4 X 25 User manual Quantity Ipe Ipe pe Ipe 2pcs Ipe 4 pes 1 pe l pe l pe 1 set 2 pes 4pes 1 pc 5 pes Ipe 29 V ee OSE7F4 USER MANUAL 5 2 Handle Orientation Left handed Right handed E Left Hand ma Right Hand _ Left Hand Reverse 26 Ql See QSE7F4 USER MANUAL 5 3 Fingerprint number amp name list Group A Group B Group C Group D No Fingerprint Fingerprint Fingerprint Fingerp
16. the infrared detector detects the finger The blue background lights green indicator light and red light on sensor flashes Or press 0 the blue background green indicator light and red light on sensor flashes place the Master finger on the sensor Figure2 6 NOTE A If the infrared detector doesn t work you can press 0 to activate the lock B After the red light on sensor flashes you must put the Master finger on the sensor within 5 seconds Otherwise the red indicator flashes followed by 2 short beeps toindicate the failed operation 2 All indicators go out along beep is heard move away the Master finger the green and redindicators flash NOTE the flash willlast about 6 seconds step 3 must be donewithin 6 seconds 3 Press 1 a long beepis heard redindicator goes out green indicator lights Figure2 7 13 14 O See QSE 7F4 USER MANUAL 2 NOTE the green indicator will light for about 4seconds step 4 must be done within 4 seconds 4 Input fingerprint number 0001 along beep is heard which indicates the successful first inputof this fingerprintnumber 5 Input fingerprintnumber 0001 the second time another long beep is heard the red indicator in the sensor flashes which means the lock is ready for enrolling group member s fingerprints NOTE If the fingerprint number is already used thered indicator flashes once and the buzzer beeps once 6 Place amember finger onthe
17. the lock isin lock out status 8 Activate the lock in the manual it means to make the buttons or sensor begin to work 3 Place the fingerprint which you wish to be the Master fingerprint on the sensor red light goes out green indicator lights all the time When the red 2 4 Function of buttons light on sensor goes out remove your finger and a long beep will Button 0 TOACTIVATETHE LOCK follow Figure2 5 10 V ee OSE7F4 USER MANUAL 2 9 3 Continued NOTE When the red light on sensor goes out you must remove your finger otherwise the red indicator flashes followed by 2 short beeps to indicate the failed setup 4 When thered light on sensor flashes again place the same fingertip on the sensor immediately the green indicator goes out followed by another long beep which indicates the successful setup NOTE The red light on sensor will flash for about 4 seconds the finger MUST be placed on the sensor within the 4 seconds Otherwise the red indicator flashes followed by 2short beeps toindicate the failedsetup 5 After setting up the Master fingerprint successfully turn the mechanical key to the original positionand draw out put the cylindercover back IMPORTANT NOTE Master fingerprint cannot beset as group member fingerprint to open thelock 2 5 2 Howto set Emergency PIN 1 Press and hold the cylinder cover button slide down the cylinder cover with another hand Figure 2 3 2 Ins
18. y 45 RH 85 RH 1 4 Components Buttons Front Eed Indicator Sensor Cylinder Battery ed cover pies Deadbolt Socket for stand by power Rear concealed by cylindercover indicator Cylinder cover Antistrike button latch Inside lever Back plate Side View Front plate V ee OSE7F4 USER MANUAL V ee OSE7F4 USER MANUAL 1 Operation Instruction 1 5 Structure view j N cover 1 ront plate eA lt gt Cylinder 2 1 Left handed and Right handed Lefthanded _ Right handed EE aa F LZ 1 Standing out of the door if the hinge is on the left it is left handed lock 2 Standing out of the door ifthe hinge is on the right it is right handed lock oO a 4 z Nj z gt __2 2_Status of the lock l ee Ki op ne 1 Lock status locked with latches not by deadbolt Figure 2 1 7 ae ENLI B lt e gt PS SO Hexagon screw er Fixing screw M5 XL gt a 2 85 2 p2 D 8 nA D ms Bais 2 1 A a V ee OSE7F4 USER MANUAL V
Download Pdf Manuals
Related Search