Home

PYLE Audio DISC CD CHANGE User's Manual

image

Contents

1. commander and disc selection will begin random play When this button is pressed for more than 2 seconds DISC and RDM are displayed At this time all Disc s are selected to play randomly To release the random selection function push either the random or disc buttons again Repeat Play Button 3 Track or DISC Repeat This is used for repeating Disc Track play Upon pressing this button once APT will be displayed on the LCD and the playing will be repeated When this button is pressed for more than 2 seconds DISC and RPT will be displayed on the LCD This will repeat the disc playing in its entirely To stop function depress either the repeat button or the disc button Play Pause Button Play Pause 4 To pause all play functions of CD Changer Push the Pause button To return to play mode depress the Pause button again Track Selection Track up down and Track FF REW 5 10 These button are used to search for a disc or track quickly Press T Up or T Down button to search to the desired track or disc Disc and track information will be displayed on the LCD Upon pressing these buttons for more than 2 seconds you may Fast Forward Rewind in the direction desired Random Sensor Receiving Light 6 This is to receive infrared signal from card type Remote Commander Avoid any foreign substances or contamination Scan Play Button Track or DISC Scan 7 Upon pressing this button SCAN is dis
2. F1 IN THE MIDDLE HOLE SPECIFICATIONS General System Usable Discs Operation voltage Power consumption Operating electric current Max peak electric current Dimensions Operational temperature range Temperature range of storage Test condition Audio Frequency range Dynamic range Distortion THO N S N ratio Channel separation Audio output level Wow amp Flutter SCRATCH INTERRUPTION BLACK DOT FINGER PRINT Compact Disc audio system Compact Disc 10 15V 6W or less DC 14 4V 400mA 14 4Volt 1 2A 14 4Volt 284 W x 186 5 O x 74 H mm 5 F 158 F 22 F 176 F Ordinary room condition of temperature 68 5 4 F and relative humidity 65 DC 14 4 0 2V 20Hz 20KHz 1dB 90dB or more 0 1 or less at 1KHz 90aB or more at 1KHz 70dB or more at 1KHz 1 25V 0 05V 1KHz OdB Below the measuring unit 0 8 mm 0 8 mm 0 8 mm lt 965 um Note Unit specifications and design parameters are subject to modification or change without prior notice due to technical improvements by the manufacturer OPERATION Liquid Crystal Display LCD 1 LCD display will only be active when the changer power is on This display indicates all operation key s including DISC number Track number and DISC icon Random Play Button 2 Track or DISC Random This is used for random selection Disc play and sequence Once this button is pressed RDM is displayed in the Upper left corner of LCD
3. PYLE PLCHD6 6 DISC CD CHANGER INSTRUCTION MANUAL IMPORTANT NOTICE This Compact Disc Changer Player has been tested and found to comply with the limits for a class B digital device in accordance with the specifications in Subpart J of part 15 of FCC Rules This equipment generates and uses radio frequency energy and it must be installed and used properly in accordance with the manufacturer s instructions CAUTION This product is designed for 12 Volt DC Negative ground systems only Your vehicle is compatible with this equipment if the negative terminal of the battery is connected to the vehicle s body chassis USE OF CONTROLS OR ADJUSTMENTS OF PERFORMANCE OR PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE DO NOT REMOVE THE CHANGER PLAYER COVER THERE ARE NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERSONNEL ONLY SAFETY PRECAUTIONS Disc Only use compact Discs which have this mark Do not use cracked bent or scratched Discs f Disc becomes dirty gently wipe the surface with a soft line free cloth Do not use sprays or cleaners designed for records Do not expose the Disc to direct sunlight Excessive heat will warp the Disc Do not leave a Disc unprotected Always store it in its case right away from sunlight Compact Discs may not always be recorded at the same volume level or with the same quality This may result in different volume levels between Di
4. Using the hex bolts with washers c 2 Determine the mounting location and drill 4 mounting holes approximately 3 5mm in diameter 3 Secure the unit in place using 4 self tapping screws e HORIZONTAL INSTALLATION a C Attach the brackets a to each side of the unit using hex bolts with washers c Attach the floor base plate b to the brackets a using the wing nuts d Lift the carpet and determine the mounting location Fix the floor base plate b to the floor using self tape screw f Press the unit to the floor and remove the wing nuts d and lift off the changer Lay down the carpet Cut 1 X on Mount the unit in place using 4 each area of the carpet where the wing nuts d mounting bolts will pass through VERTICAL INSTALLATION Attach the brackets a to each side of the unit using hex bolts with washers c Lift the carpet and determine the mounting Attach the floor base plate b to the brackets a location Fix the floor base plate b to the floor using the wing nuts d using self tape screw f Press the unit to the floor and Lay down the carpet Cut 1 X on Mount the unit in place using 4 remove the wing nuts d and lift each area of the carpet where the wing nuts d off the changer mounting bolts will pass through FOR AN ANGLED INSTALLATION TURN TO THE 45 POSITION AND ATTACH LOCK SCREW
5. ake sure that the magazine toadied with Discs before inserting it into the player Be careful to insert the magazine into the player with the label tacking upward 3 Close the door Do not leave the door open during Disc playback Dirt dust or other foreign may cause damage to the player if allowed to enter WAL W Removing the magazine 1 Open the door 2 Press the Eject button to remove INSTALLATION Use the supplied parts and mount the unit securely The use of parts other than these supplied specified may loosen or damage internal components e f installation presents any difficulties consult your dealer for advice Before drilling a hole into the wall or floor the vehicle trunk check that nothing is behind the panel Never drill a hole in the fuel tank or any other important that may be attached to the trunk e Take off the negative terminal connector of the car battery to prevent short circuits while you are installing the unit T l TOP TOP E Proper Mie FRONT FRONT d Location Be sure to mount the unit in a location that will not interfere with the driver or passengers Be certain there is not danger of passengers being injured case of sudden stops Do not mount the player near heater outlets where it might be affected by heat or near doors where rainwater might splash onto it Do not mount the player in a location that will rec
6. eive direct sunlight such as on the dashboard or the rear shell Excess heat will damage the player e When mounting the player make sure no wires are trapped between the player and the surrounding metalwork or fittings Do not mount the player on the spare lire board or any other unstable place Do not mount the player where it will impede access to the spare tire jack or tools e Although the player can be mounted horizontally vertically or at 45 keep to the tolerable angles shown on following page In addition choose a place where the CD magazine can be loaded and unloaded easily ACCESSORIES ah SE x2 a Bracket b Floor base plate c Hex bolt M5x12 with Washers d ef UNE d x4 x4 x4 x1 d Wing nut 06 e Self tape screw 5x15 f Self tape screw 3x15 g Mount angle adjust key Important Angle set and locking screws Be sure to adjust the mounting angle set screw F using the mounting angle adjust key to appropriate angle Of for horizontal 45 angle or 90 for vertical mounting After adjustment be sure to attach the locking screws F1 into the corresponding hole on both sides of the player amp F1 O 0 F O horizontally O F1 45 Faa O slant mounting 45 O 90 F Qo F vertically INSTALLATION DIAGRAMS HORIZONTAL VERTICAL INSTALLATION PROCEDURES 1 Attach the brackets a to each side of the unit
7. is erratic REMOVE THE TRANSPORT SCREWS Four screw that lock the CD player s mechanism during transport are located on the bottom of the unit Remove these screws and keep with your literature package for future use should the unit need to be transported for service maintenance After removal be sure to seal these holes using the adhesive stickers provided with the unit LOCATION OF CONTROLS 1 Compact Disc Magazine Slot 2 Reset Button 3 Eject Button Press this button to eject the Magazine 4 Slide Door WIRING CONNECTIONS CAR RADIO CD CHANGER T HOW TO USE THE COMPACT DISC MAGAZINE Inserting Discs Inserting Discs into the supplied magazine Up to 6 Discs may be inserted into the magazine The Disc are numbered from 1 bottom tray to 6 top tray Note Do not touch the recorded side of a Disc while inserting or removing it Removing Discs 1 Press the Eject button to remove the Magazine 2 Push the Release keys to remove the Discs Precautions Do not leave the magazine exposed to high temperature or direct sunlight Do not attempt to disassemble the magazine e Take care not to drop the magazine or knock it against hard surfaces Store the pulled out magazine in a safe place Benzine thinner or other volatile chemicals may cause damages to the magazine Inserting the magazine 1 Slide the door open to the right side 2 Insert the magazine M
8. played in the lower left corner LCD display The unit will play each Track on disc for 10 seconds When this button is pressed for more than 2 seconds DISC and SCAN will be displayed and unit will play first 10 seconds of each disc Disc Selection Button DISC Select 8 11 Press D Up button to select upper DISC and press D Dn button to select the lower DISC All disc functions will be displayed on the commander LCD Power Button Power On Off 9 Press this button to turn On Off the changer 10 ERROR DISPLAY Error 1 Error 2 Error 3 Error 4 Error 5 Error 6 Error 7 Error 8 Error 9 There s no Magazine and DISC is clamping It is impossible to discharge Magazine while ejecting Loading is not completed after a certain time 8 sec passed Unloading is not completed after a certain time 8 sec passed Elevator does not reach to the target position after a certain time 8 sec passed Hole separated Pickup is not moved to the center area even after a certain time 8 sec passed in movement of Sled center area It is not completed despite more than 3 time of Focusing trial CLV On is not operated to reach CLV constant speed Mode and Subq input is proven Error TOC is not read after a certain time 15 sec passed Error 10 The temperature in the mechanism continues to rise for a certain times 5 Note Sec so no more operation can be done When the system is t
9. sc and radio ENVIRONMENTAL CONDITIONS The unit may not function properly if exposed to extreme temperatures To assure normal operation keep vehicle s interior temperature within normal range In cold environmental conditions Water mist moisture may form on the optical lens when the vehicle interior heater is turned ON Allow moisture to evaporate before use If a parked vehicle has been exposed to direct sunlight cool down interior before use Always keep the magazine door closed Do not expose your unit to extreme levels of humidity or dusty environments In the interest of safety while driving set the volume control level so that sounds outside the vehicle can still be heard Playing a Disc while driving on a very bumpy road may result in skips but this will not scratch the Disc or damage the player INTRODUCTION RESET FUNCTION A RESET button is located on the front panel to the left side of EJECT button and is accessible only when the magazine door is opened The RESET button is recessed in order to prevent accidental engagement and can be activated with the tip of ball point pen or any similar pointed object The reset circuitry is provided in order to protect the unit s microprocessor and tracking system and should be activated only under the following conditions a Initial installation after all wiring is completed b Abnormal operation is encountered such as not loading a Disc and c Indication on controller display
10. urned off in the car power always goes back to the radio not back to the CD player When power is restored to the CD System It does not start where it was last playing It always goes back to the number 1 song on the disc If you want to play a CD turn the system on via the commander or remote control If you want to listen to radio or cassette turn power on via the radio www pyleaudio com 88 D0020 26

Download Pdf Manuals

image

Related Search

Related Contents

Printer-Scanner Troubleshooting    RY-S-CS-Z003 Handling and Storage Manual 10_01_14 Rev1  +48 085 681 64 29 +48 085 681 63 82 +48 085 682 71 10  CS/BS Series PABX User Manual  Durable Interactive Whiteboard Clean  Technische Details    Lenovo 9964 Personal Computer User Manual  MCP120取扱説明書  

Copyright © All rights reserved.
Failed to retrieve file