Home

Philips EIP-4500 User's Manual

1. 36 6 9 Reset TV to factory settings 36 7 Connect devices 37 7 1 Connection overview 37 7 2 Select connection quality 38 73 Connect devices 40 74 Setup devices 44 7 5 Use Philips EasyLink 45 7 6 Prepare TV for digital services 46 8 Technical specifications 47 9 Troubleshooting 48 10 Index cece eens 51 2008 Koninklijke Philips Electronics All rights reserved Specifications are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners Philips reserves the right to change products at any time without being obliged to adjust earlier supplies accordingly The material in this manual is believed adequate for the intended use of the system If the product or its individual modules or procedures are used for purposes other than those specified herein confirmation of their validity and suitability must be obtained Philips warrants that the material itself does not infringe any United States patents No further warranty is expressed or implied Warranty No components are user serviceable Do not open or remove covers to the inside of the product Repairs may only be done by Philips Service Centres and official repair shops Failure to do so shall void any warranty s
2. 7 3 3 Connect the antenna cable 9 3 4 Connect the mains cord 9 3 5 Insert the remote control batteries 10 3 6 Switch on 10 3 7 First time setup 10 4 Use yourTV 11 4 1 Switch your TV on off or to standby 11 42 Wath V oerte EPICURI DEREN 12 4 3 Watch connected devices 12 4 4 _ 13 4 5 UseAmbilight 13 5 Use more of yourTV 14 5 1 Remote control overview 14 5 2 UseTV menus 16 5 3 Adjust picture and sound settings 18 5 4 Adjust Ambilight settings 22 5 5 Adjust LightGuide brightness 22 5 6 Change to Shop or Home mode 23 5 7 Use advanced teletext features 23 5 8 Create favorite lists 25 5 9 Use the Electronic Programme Guide 26 5 10 Use timers and Child lock 27 5 11 Use subtitles 28 5 12 View photos and listen to music 29 5 13 Listen to digital radio channels 31 5 14 Update your TV software 31 Install channels 33 6 1 Automatically install channels 33 6 2 Manually install channels 34 6 3 Rename channels 35 6 4 Uninstall or reinstall channels 35 6 5 Rearrange channels 35 6 6 Manually update the channel list 35 6 7 Test digital reception 36 6 8 Starta
3. Start show Stop show Starts or stops a slide show 5 12 4 View pictures as thumbnails Thumbnails allow you to view picture albums in an overview format oO e w oM Select a picture album Press gt to enter the picture list Press the green key Press A or v 4 or gt to highlight a picture Press OK to view the picture Press 4 to return to the thumbnail overview Press the green key again to go back to the picture list 5 12 5 Listen to music After connecting your USB storage device to the TV press gt to enter the Multimedia menu Select Music then press gt to enter the Music folder 3 Press A or v to select a song or a music album 4 Press OK to play the selected song or album Music settings No details More details Displays the file name Repeat one all Repeat a song or an album Shuffle Play songs in a random sequence 5 12 6 View a slide show with music You can view a slide show of your stored pictures with background music 1 Select an album of songs first then press OK 2 Select an album to display then press OK 5 13 Listen to digital radio channels If digital broadcasting is available digital radio channels are installed automatically during installation To reorder the digital radio channels see Section 6 5 Rearrange the channels 1 Press OK on the remote control The All channels menu is displayed 2 Use the number keys to select
4. Channel install Baxs ase Preferences Hearing impaired Connections Factory settings Press gt to enter the Languages menu Press A or v to select your language Press OK to confirm Ux GE Press 4 to return to the Installation menu In addition to menu language you can configure the following language settings via the Languages menu digital channels only ENGLISH e Preferred audio Select one of the available audio languages as your preferred audio language For more information see Section 5 3 5 Adjust sound settings Preferred subtitles Select one of the available subtitle languages For more information see Section 5 11 3 Select a subtitle language on digital TV channels Hearing impaired If available select On to display the hearing impaired version of your preferred audio or subtitle language Step 2 Select your country Select the country where you are located The TV installs and arranges channels according to your country 6 Note Skip to Step 3 Select your time zone if your country settings are correct 1 In the Installation menu press v to select Country 2 Press gt to enter the list 3 Press A or v to select your country 4 Press 4 to return to the Installation menu Step 3 Select your time zone 6 Note This option is only available for countries with different time zones Skip this step if it is not applicable 1 In the Installatio
5. Depending on the size of your TV screen purchase one of the following wall brackets TV VESA Special screen compatible size wall bracket inches type cm millimeters 32 81cm Adjustable instructions The VESA compatible bracket must be adjusted 300 x 300 to 200 x 300 before securing to the TV 37 94cm Fixed 300 x 300 42 107cm Fixed 400 x 400 None or larger EN 7 Step 2 Remove the TV stand Note These instructions are only applicable to TV models with mounted stands If your TV stand is not mounted skip to Step 3 Secure the VESA compatible wall bracket to the TV TV stands may differ in shape on some TV models 1 Carefully place the TV face down on a flat stable surface that is covered by soft cloth The cloth should be thick enough to protect your screen 2 Using a cross head screwdriver not supplied unscrew the four bolts that secure the stand to the TV 3 Firmly pull the stand from the bottom of the TV Place both the stand and bolts in a secure location for future reinstallation EN 8 Step 3 Secure the VESA compatible wall bracket to the TV 1 Locate the four mounting nuts at the back of the TV 2 Continue with the instructions provided with your VESA compatible wall bracket amp NOTE When securing the VESA compatible wall bracket to your TV use M6 bolts for 32 inch m
6. Colour 22 Mode 22 Separation 22 Best effect 7 Change mode 13 Use 13 Use during standby 22 Analogue Channel installation 34 Fine tune channels 35 Antenna Connect 9 Assign Devices 44 Audio language 21 Automatic Channel installation 33 Surround 21 Volume leveling 21 B Back connectors 5 Balance Ambilight 22 Sound 21 Brightness 18 c Care Environment 4 Screen 4 Channels All channels list 25 Change 12 Decoder 45 Favorite lists Select 25 Setup 25 Use 25 Installation ENGLISH Automatic 33 Manual 34 Rearrange 35 Rename 35 Test digital reception 36 Uninstall 35 Update channel list 35 Child lock Lock all channels devices 28 Lock from a certain time 28 Lock one or more channel device 28 Set change code 27 Set parental rating 28 Clock 18 Colour enhancement 19 Component cable 39 Composite 39 Conditional Access Module CAM Insert 46 Menu 46 Connections Back connectors 37 Cable quality Component 39 Composite 39 HDMI 38 SCART 39 S Video 39 Devices Blu ray Disc player 40 Conditional Access Module CAM 46 DVD player 40 EN 51 DVD recorder Digital receiver 42 DVD recorder Home theatre system 43 DVD recorder Receiver 42 Game console camcorder 44 HD digital receiver 41 PC 44 Satellite receiver 41 USB 29 Philips Easylink Enable disable 45 Use 45 Setup devices Assign channel decoder 45 Assign to connectors 44 Side connectors 38 Contrast 18 Country Selection 33 Custo
7. Create your Favourite channel lists here Picture Sound Ambilight Programme guide Available when digital channels are installed this item displays information about the digital programmes See Section 5 9 Use the Electronic Programme Guide Multimedia Select this item to view photos or play music stored on a USB device See Section 5 12 View photos and listen to music EN 16 4 Press w to select Picture TV settings Picture Settings assistant KEJING Reset smart settings Colour Sound Hue Ambilight Pixel Plus HD Natural Motion 5 Press gt to enter the Picture settings Picture Contrast Contrast 90 Brightness 47 Colour 52 Hue Sharpness 4 Tint Pixel Plus HD Natural Motion 6 Press v to select Brightness Picture Brightness Contrast 98 Brightness 47 Colour 52 Hue 0 Sharpness 4 Tint Pixel Plus HD Natural Motion 7 Press gt to enter the Brightness setting Brightness 8 Press A or v to adjust the setting 9 Press 4 to return to the Picture settings or press MENU to exit 6 Note More choices are available when digital channels are installed and broadcast ENGLISH 5 2 3 Use the Quick access menu The Quick access menu gives direct access to some often needed menu items 6 Note When digital channels are installed and broadcasted the relevant digital options are displayed in the
8. Right OK MENU PROGRAM VOLUME AMBILIGHT For advanced information about the remote control see Section 5 1 Remote control overview 3 Get started This section helps you position and install the TV and supplements the information provided in the Quick Start Guide Note Refer to the Quick Start Guide for stand mounting instructions A WARNING 3 2 Wall mount the TV ENGLISH Wall mounting of the TV should only be performed by qualified installers Koninklijke Philips Electronics N V bears no responsibility for improper mounting that results in accident or injury 3 1 Position the TV In addition to reading and understanding the safety instructions in Section 1 1 consider the following before positioning your TV e The ideal viewing distance for watching TV is three times its screen size Position the TV where light does not fall on the screen Connect your devices before you position your TV Your TV is equipped with a Kensington Security Slot at the back of the TV If connecting an anti theft Kensington lock not supplied position the TV within reach of a permanent object such as a table that can be easily attached to the lock For the best Ambilight effect position the TV 10cm four inches to 20cm eight inches away from the wall Ambilight works best in a room with dim lighting Step 1 Purchase a VESA compatible wall bracket
9. VCRs digital receivers game consoles and other SCART devices Supports Audio L R CVBS in out RGB 2 EXT 2 Second SCART connector Supports Audio L R CVBS in out RGB 3 EXT 3 Component video Y Pb Pr and Audio L R input connectors for DVD players digital receivers game consoles and other component video devices 4 SPDIF OUT SPDIF sound output connector for home theatres and other audio systems 5 AUDIO OUT L R Sound output cinch connectors for home theatres or other audio systems 6 TV ANTENNA 7 HDMI 1 2 3 HDMI input connectors for Blu ray Disc players digital receivers game consoles and other high definition devices 6 Note The number of HDMI connectors available may vary according to your TV model 8 AUDIO IN Mini jack connector for PC audio in when connecting a PC via DVI HDMI adaptor EN 37 Side connectors 9 Headphones Stereo mini jack 10 AUDIO L R Audio L R input connectors for composite and S Video devices 11 VIDEO Video input cinch connector for composite devices 12 S VIDEO S Video input connector for S Video devices 13 USB USB connector for storage devices 14 HDMI Additional HDMI connector for mobile high definition devices 15 COMMON INTERFACE Slot for Conditional Access Modules EN 38 7 2 Select connection quality This section describes how you can enhance your audio visual experience by connecting your devices with the best possible con
10. less than 5 C open the box and wait until the TV matches the ambient temperature of the room before unpacking To avoid short circuit do not expose the TV remote control or remote control batteries to rain or water Do not place vessels of water or other liquids on top of or near the TV Spilling liquids on the TV can cause electric shock If liquids are spilt on the TV do not operate the TV Immediately disconnect the TV from the mains and have the TV checked by a qualified technician To avoid risk of fire or electric shock do not place the TV remote control or remote control batteries near naked flame sources e g lighted candles and other heat sources including direct sunlight ENGLISH Do not install the TV in a confined space such as a bookcase Leave a space of at least 10cm four inches around the TV for ventilation Be sure air flow is not obstructed If placing the TV on a flat solid surface be sure to use only the supplied stand Do not move the TV if the stand is not properly screwed to the TV Wall mounting of the TV should only be performed by qualified personnel The TV must only be mounted on an appropriate wall bracket and on a wall that can safely hold the weight of the TV Improper wall mounting can result in severe injury or damage Do not attempt to wall mount the TV yourself If the TV is mounted on a swivel base or swivel arm ensure no strain is placed on the power cord when th
11. 27 Pictus EWE Paris_2006 LO LO Jean jpg LO Press to enter the Picture folder Press A or v to select a picture or a picture album on the USB device Picture Afrika 2001 Afrika 2001 LO Kenya jpg Paris 2005 Congo jpg My carjpg I9 Victoria jpg Jean jpg Dakar jpg Mary jpg O Cairo jpg Afrika_2001 Afrika_2001 Kenya jpg Congo jpg Kenya jpg Victoria jpg Dakar jpg Cairo jpg Press OK to view the picture or to start a slide show of the pictures in the album Press OK to pause the slide show Press OK again to restart Press one of the colour keys on the remote control to perform the corresponding function shown at the bottom of the screen Press the blue key to stop the show and to see more functions If the function bar at the bottom disappears press any colour key to make it reappear Press 4 and select another picture or another album EN 30 Slide show settings No details More details Displays the picture name date size and next picture in the slide show Transitions Displays the list of available transition styles of the pictures Press A or v to select and press OK to activate Slide time Sets the time lag for picture transitions Short Medium or Long Rotate Rotates a picture Zoom Displays a list of available zoom magnifications
12. Different types of connectors may be used to connect a device to your TV depending on availability and your needs 7 3 1 Blu ray Disc player For full high definition video connect a HDMI cable as illustrated BEEN Blu ray Disc player V J 7 3 2 DVD player For DVD video connect a SCART cable as illustrated gt TV EN 40 aa DVD Player 7 3 3 Satellite receiver To receive analogue channels via antenna and digital channels via a satellite receiver connect an antenna cable and SCART cable as illustrated TV ENGLISH Q 6 N e a Ho I Hd HH Hd EE oo Bd HM woW2 D D Satellite receiver 7 3 4 HD digital receiver To receive analogue channels via antenna and digital channels via a HD digital receiver connect two antenna cables and HDMI cable as illustrated 2 HD Digital receiver HD Satellite receiver EN 41 7 3 5 Combined DVD recorder and digital receiver To receive analogue channels via antenna and record programs on a combined DVD recorder and digital receiver connect two antenna cables and one SCART cable as illustrated XXXIX AUDIO I
13. Displays information about the next programme Remind Marks a programme as a reminder Watch Watch or listen to a current programme Jump to Jumps to the next or previous day Info If available displays information about a selected programme 3 Press T GUIDE to exit the EPG 5 9 2 More 7 or 8 day EPG Searching by genre scheduling reminders and more features are available through the Programme guide menu 1 Press T GUIDE on the remote control 2 Press MENU on the remote control The Programme guide menu appears Programme guide What s on 12 30 South Today Search by genre Scheduled remind SIT alma Preferred EPG WE D Acquire EPG data Press A or v to select a menu option Press gt to enter Press A or to make a selection 9 unm de tw Press OK or the green key to activate the selection 7 Press Q GUIDE to exit the EPG Note Only channels marked as preferred EPG channels appear in the Programme guide menu 5 10 Use timers and Child lock This section describes how to switch the TV on or off at a specified time and to use Child lock 5 10 1 Automatically switch the TV to standby Sleeptimer Sleeptimer switches the TV to standby after a defined period of time 1 Press MENU on the remote control and select TV menu gt Features gt Sleeptimer 2 Press gt to enter the Sleeptimer bar 3
14. Done appears 8 Press MENU to exit 6 3 Rename channels 1 Press MENU on the remote control and select TV menu gt Installation gt Channel installation gt Rearrange 2 Press gt to enter the Rearrange list 3 Press A or v in the Rearrange list to select the channel you want to rename 4 Press the red key 5 Press 4 and to select characters or A and v to change the characters Space numbers 0 9 and other special characters are located between z and A 6 Press the green key or OK to finish Q Tip Delete all characters by pressing the yellow key Delete only the highlighted character by pressing the blue key 6 4 Uninstall or reinstall channels ENGLISH You can uninstall a stored channel or reinstall an uninstalled channel 1 Press MENU on the remote control and select TV menu gt Installation gt Channel installation gt Rearrange 2 Press gt to enter the Rearrange list 3 Press A or v to select the channel you want to uninstall or reinstall 4 Press the green key to uninstall or reinstall the channel 5 Press MENU to exit 6 5 Rearrange channels 1 Press MENU on the remote control and select TV menu gt Installation gt Channel installation gt Rearrange 2 Press gt to enter the Rearrange list 3 Press A or v to select the channel you want to rearrange 4 Press the yellow key to move the channel up the list or press the blue key to move the channel
15. TV overview Side controls and indicators Fa T 9 6 m 5 1 POWER 2 PROGRAM 3 MENU 4 VOLUME 5 Standby indicator Remote control sensor 6 LightGuide Side connectors va 2 Use the TV side connectors to connect to mobile devices such as a camera or high definition game console You can also connect a pair of headphones or a USB memory device Back connectors ENGLISH e Use the TV back connectors to connect to the antenna and permanent devices such as a high definition disc player DVD player or VCR 6 Note For more information about connections see Section 7 Connect devices EN 5 Remote control Source e 2 3 Ea susme 3 DEMO MHEG CANCEL 0 PSP AMBILIGHT MODE PHILIPS TELEVISION V J D amp qe 6 7 8 9 STANDBY SOURCE TELETEXT COLOUR KEYS From left Red green yellow blue NAVIGATION KEYS Up A Down v Left 4
16. Video Good quality Jc An analogue connection S Video provides better picture quality than composite video When connecting your device with S Video plug the S Video cable to the S Video connector on the side of the TV You must connect a separate Audio L R cable from the device to the red and white Audio L R connectors on the side of the TV ENGLISH TN M 2 S Video cable Audio L R cable Red White M Audio L R cable Red White Component video cable Red Green Blue 7 2 3 SCART Good quality Jc SCART combines audio and video signals in one cable Audio signals are stereo while video signals can be composite or S Video quality SCART does not support high definition video and is analogue Two SCART connectors are provided on the TV EXT 1 and EXT 2 7 2 5 Composite Basic quality Composite video provides basic analogue connectivity usually combining a yellow video cinch cable with red and white Audio L R cinch cable Match the cable colours when connecting to the composite Video and Audio L R input connectors on the side of the TV Composite audio video cable Yellow red and white EN 39 7 3 Connect devices This section describes how to connect various devices with different connectors and supplements examples provided in the Quick Start Guide Caution Disconnect the mains cord before connecting devices Note
17. a radio channel 3 Press OK 5 14 Update your TV software Philips continuously tries to improve its products and we strongly recommend that you update the TV software when updates are available Check www philips com support for availability ENGLISH 5 14 1 Check your current software version Press MENU on the remote control and select TV menu gt Software update gt Current software info 5 14 2 Check if software updates are available Philips periodically transmits messages via digital broadcast announcing when software updates are available Press MENU on the remote control and select TV menu gt Software update gt Announcement 5 14 3 Update software digital broadcasts If using DVB T digital broadcasts your TV automatically receives software updates If you receive a message on screen prompting you to update your software Select Now recommended to update the software immediately Select Later to be reminded to update the software later Select Cancel to exit the update not recommended If you cancel the update manually update the software by pressing MENU and selecting TV menu gt Software update gt Local updates Follow the on screen instructions EN 31 5 14 4 Update software analogue broadcasts Note Before performing this procedure be sure to Set aside some time to complete the entire update Have available a USB storage device wi
18. and 7 4 3 EN 49 ENGLISH 9 6 USB connection issues The TV does not display the USB device content e Set your device to Mass Storage Class compliant as described in your device documentation e Your USB device may not be compatible with the TV Not all audio and picture files are supported See Section 8 Technical specifications for a list of supported file types Audio and picture files do not play or display smoothly e The transfer performance of the USB device may limit the transfer rate 9 7 PC connection issues The PC display on my TV is not stable or is not synchronised e Check that a supported resolution and refresh rate is selected on your PC See Section 8 Technical specifications for supported resolutions and refresh rates EN 50 9 8 Contact us If you cannot resolve your problem refer to the FAQ for this TV at www philips com support If the problem remains unresolved contact the Customer Support Centre in your country as listed in this user manual A WARNING Do not attempt to repair the TV yourself This may cause severe injury irreparable damage to your TV or void your warranty 6 Note Please have available your TV model and serial number before contacting us These numbers are available on the back and side of your TV as well as on the packaging 10 Index A Active Control 19 All channels list 25 Ambilight Adjust settings Balance 22 Brightness 22
19. channels 31 Rearrange channels 35 Recycling product 4 Remote control Advanced use 14 Basic use 6 Batteries 10 Rename channels 35 Reset to factory settings 36 S Safety information 3 SCART cable 39 Screen care 4 Settings Ambilight Adjust settings 22 Light Guide Adjust brightness 22 Picture Adjust settings 18 Change format 20 Use Settings assistant 18 Use smart settings 19 Sound Adjust settings 21 TV location Change location 23 Setup devices 44 Sharpness 18 Shop mode 23 Side Connectors 5 Controls 5 Sleeptimer 27 EN 53 Smart settings Current 19 Movie 19 Standard 19 Vivid 19 Software update Check availability 31 Check version 31 Update analogue 32 Update digital 31 Sound Adjust settings Audio language 21 Automatic volume leveling 21 Auto surround 21 Balance 21 Delta volume 21 Dual I II 21 Equalizer 21 Headphone volume 21 Mono Stereo 21 Surround mode 21 Volume 21 Stereo sound 21 Subtitles Analogue TV 28 Digital TV 29 Language 29 Surround sound Auto 21 Mode 21 S Video 39 Switch TV Off 11 On 10 11 On from standby 11 To standby 11 System selection 34 T Technical specifications 47 EN 54 Teletext Advanced use Cycle subpages 24 Digital teletext 24 Dual screen 23 Enlarge 24 Language 24 Reveal 24 Search 23 Select subpages 23 Teletext 2 5 24 T O P broadcasts 23 Timers On timer 27 Sleeptimer 27 Time zone 33 Tint 18 T O P teletext 23 Troubleshooting 47 TV Ambilight 13 C
20. comply with all applicable legal requirements and to stay well within the EMF standards applicable at the time of producing the products Philips is committed to develop produce and market products that cause no adverse health effects Philips confirms that if tts products are handled properly for their intended use they are safe to use according to scientific evidence available today Philips plays an active role in the development of international EMF and safety standards enabling Philips to anticipate further developments in standardisation for early integration in its products Mains fuse UK only This TV is fitted with an approved moulded plug Should it become necessary to replace the mains fuse this must be replaced with a fuse of the same value as indicated on the plug example 10A 1 Remove fuse cover and fuse 2 The replacement fuse must comply with BS 1362 and have he ASTA approval mark If the fuse is lost contact your dealer in order to verify the correct type 3 Refit the fuse cover In order to maintain conformity to the EMC directive the mains plug on this product must not be detached from the mains cord Copyright VESA FDMI and the VESA Mounting Compliant logo are trademarks of the Video Electronics Standards Association Manufactured under license from Dolby Laboratories Dolby Pro Logic and the double D symbol Oo
21. devices Compliant devices must be connected to your TV via HDMI and assigned as described in Section 7 4 1 Assign devices to connectors 7 5 1 Enable or disable EasyLink 1 Press MENU on the remote control then select TV menu gt Installation gt Preferences gt EasyLink 2 Select On or Off 7 5 2 Use one touch play After enabling EasyLink press play on your device The TV automatically switches to the correct source 7 5 3 Use one touch standby Press and hold b STANDBY on the TV or device remote control for at least three seconds The TV and all connected HDMI devices switch to standby EN 45 7 6 Prepare TV for digital services Scrambled digital TV channels can be decoded with a Conditional Access Module CAM and a Smart card provided by a digital TV service operator The CAM may enable several digital services depending on the operator and services you choose for example pay TV Contact your digital TV service operator for more information about services and terms 7 6 1 Using the Conditional Access Module A WARNING Switch off your TV before inserting a CAM Be sure to follow the instructions described below Wrong insertion of a CAM may damage both the CAM and your TV 1 Following the directions printed on the CAM gently insert the CAM into the Common Interface on the side of the TV 3 Turn on the TV and wait for the CAM to be activ
22. moma DVD Recorder Digital receiver 7 3 6 Separate DVD recorder and receiver To receive analogue channels via antenna and record programmes on a separate DVD recorder and receiver connect three antenna cables and three SCART cables as illustrated TV DVD Recorder Receiver Cable box EN 42 7 3 7 DVD recorder and home theatre system To receive analogue channels via antenna output sound to a home theatre system and record programmes on a DVD recorder connect two antenna cables one SCART cable and two digital audio cables as illustrated ENGLISH DIGITAL AUDIO IN MoMa DVD Recorder Home Theatre System Note If using a home theatre or other audio system the best synchronisation between images and sound is achieved by connecting the audio signal from your playback device to the TV first Subsequently channel the audio signal to the home theatre system or audio device via the audio connectors on the back of the TV EN 43 7 3 8 Game console or camcorder The most practical connection for a mobile game console or camcorder may be at the side of the TV You can for example connect the game console or camcorder to VIDEO S Video and AUDIO L R connnectors at the side of the TV A HDMI connector is also available for high definiti
23. GLISH Balance Sets the balance of the left and right speakers to best fit your listening position Audio language Lists audio languages available for a digital channel unavailable on analogue channels Dual I Il If available choose between two different languages Mono Stereo If stereo broadcasting is available choose between mono or stereo Surround mode If surround sound Virtual Dolby Surround is available enable it for more spatial sound Headphone volume Changes the volume of your headphones 6 Note When headphones are connected press the MUTE button on the remote control to mute audio from the TV speakers Pressing VOLUME buttons un mutes the TV speakers Automatic volume leveling Reduces sudden volume changes for example during commercials or when switching from one channel to another Select On or Off Delta volume Levels out volume differences between channels or connected devices You must switch to the connected device before changing the Delta volume Auto surround Automatically switches the TV to the best surround sound mode available from a broadcast Select On or Off EN 21 5 4 Adjust Ambilight settings 1 Press MENU on the remote control and select TV menu gt TV settings gt Ambilight 2 Press gt to enter the list TV settings Ambilight Settings assistant Reset smart settings Picture Sound Colour Ambilight Se
24. IDE Toggles the Electronic Programme Guide on or off Only active with digital channels DEMO Toggles the Demo menu on or off TELETEXT Toggles teletext on or off DUAL SCREEN Splits the current channel or source on the left of the screen Teletext appears on the right ENGLISH EN 15 5 2 UseTV menus 5 2 2 Use the main menu The following example describes how to use On screen menus help you install your TV the main menu adjust picture sound and Ambilight settings and access other features This section describes how to navigate the menus 5 2 1 Access the main menu e 8 i 1 Press MENU on the remote control to display the main menu Channel list 1 Press MENU on the remote control to Programme guide display the main menu Multimedia Television TV menu Channel list 2 Press gt to enter the TV menu Programme guide TV menu TV settings Multimedia TV settings Settings assistant Features Reset smart settings 2 Press MENU to exit Installation Picture Software update The main menu offers the following items TV menu Select this menu for installation picture and sound settings Ambilight and other feature TV settings Settings assistant settings Settings assistant Reset smart settings 997 Press gt to enter the TV settings menu Channel list Select this item to display the Channel list
25. MHEG Cancel to cancel digital text or interactive services Caution Digital text services are blocked when subtitles are broadcasted and Subtitle On is set in the Features menu as described in Section 5 11 Subtitles 5 7 8 Use Teletext 2 5 If broadcasted by the TV channel Teletext 2 5 offers more colours and better graphics than normal teletext Teletext 2 5 is switched on by default 1 Press MENU on the remote control and select TV menu gt Installation gt Preferences gt Teletext 2 5 2 Press gt to enter the list 3 Select On or Off 4 Press OK to change the option 5 8 Create favorite lists Use the All channels list or setup a favourite list of your own with preferred TV channels and radio stations Each member of your family can create his or her own favourite list 5 8 1 Select a favorite list 1 Press OK on the remote control Alternatively press MENU and select Channel list If this is new installation the All channels list is displayed All channels EXT 3 HDMI 1 Analogue channel 1 2 Digital channel 1 3 Digital channel 2 4 Radio channel 1 Select list If this is not a new installation the last selected favourite list appears 2 Press the red key to display all favourite lists 3 Press A or to select a list 4 Press OK The selected favourite list appears 5 Press OK again to exit 5 8 2 Setup a favorite list 1 Press OK on the
26. Press A or v to set the sleep time This can be up to 180 minutes in steps of five minutes If set to zero minutes the Sleeptimer is switched off 4 Press OK to activate the Sleeptimer 6 Note You can always switch off your TV earlier or reset Sleeptimer during the countdown ENGLISH 5 10 2 Automatically switch the TV on On timer On timer switches the TV to a specified channel at a specified time from standby 1 Press MENU on the remote control and select TV menu gt Features gt On timer 2 Press gt to enter the On timer menu 3 Use A or V 4 or gt to select and enter the menu items to set a channel day of the week frequency and starting time 4 Press OK to confirm 5 Press MENU to exit Q Tip To switch off On timer select Off in the On timer menu 5 10 3 Lock TV channels or connected devices Child lock Lock TV channels or connected devices with a four digit code to prevent children from watching unauthorised content To set or change the Child lock code 1 Press MENU on the remote control and select TV menu gt Features gt Set code or Change code 2 Press gt to enter the code setup 3 Enter your code with the number keys The Features menu reappears with a message confirming that your code is created or changed Q Tip If you forget your code enter 8888 to override any existing codes EN 27 To enter the Child lock menu 1 Press MENU on the remote
27. Quick access menu 1 Press OPTION on the remote control 2 Press A or v to select an option Audio language digital See Section 5 3 5 Adjust sound settings Subtitle language digital See Section 5 11 3 Select a subtitle language on digital TV channels Subtitle See Section 5 11 Use subtitles Picture format See Section 5 3 4 Change picture format Equalizer See Section 5 3 5 Adjust sound settings Clock 3 Press OK to display the selected option menu 4 Press A V 4 gt to adjust the settings in the menu 5 Press OPTION to exit the menu BACK LW NI OPTION e 17 To display or hide the clock 1 In the Quick access menu select Clock and press OK to display the clock permanently Quick access Audio language Subtitle language Subtitle Picture format Equalizer 2 Press OPTION and press A or to select Clock again 3 Press OK to hide the clock 5 3 Adjust picture and sound settings This section describes how to adjust picture and sound settings 5 3 1 Use Settings assistant Use Settings assistant to guide you through picture sound and Ambilight settings 1 Press MENU on the remote control and select TV menu gt TV settings gt Settings assistant 2 Press gt to enter 3 Press OK to Start now 4 Press the green key on the remote control to start the assistant 5 Press 4 o
28. Register your product and get support at www philips com welcome EN USER MANUAL PHILIPS Model www philips com support Serial onan Country Number Tariff Austria 0810 000205 0 07 min Belgium 078250145 0 06 min Bulgaria 3592 489 99 96 local Croatia 01 3033 754 local Czech Rep 800142840 free Denmark 3525 8759 local Finland 09 2311 3415 local France 0821 611655 0 09 min Germany 01803 386 852 0 09 min Greece 0 0800 3122 1280 free Hungary 0680018189 free Ireland 0800 055 6882 free Italy 840320086 0 08 min Luxembourg 40 6661 5644 local Netherlands 0900 8407 0 10 min Norway 2270 8111 local Poland 0223491504 local Portugal 2 1359 1442 local Romania 1 203 2060 local Russia 495 961 1111 local Serbia 381 114 440 841 local Slovakia 0800 004537 free Slovenia 01 280 95 22 local Spain 902 888 784 0 10 min Sweden 08 5792 9100 local Switzerland 0844 800 544 local Turkey 0800 261 3302 local UK 0870 900 9070 local Ukraine 044 254 2392 local This information is correct at the time of press For updated contact information refer to www philips com support Table of contents 1 Important esee 3 1 1 dSafety c oos A E A 3 12 Screen 4 1 3 Environmental care 4 2 Your esr AE ee es 5 2 4 TV overview 5 3 lt 7 3 1 Position the TV 7 3 2 Wall mount the TV
29. The first time you switch on the TV check that the mains cord is properly connected When ready turn on the mains if mains switch is available then press POWER on the side of the TV Note Certain TV models require you to press and hold POWER for up to two seconds A beep sound indicates that your TV is switched on Your TV may take up to 15 seconds to start EN 10 3 7 First time setup 1 The first time the TV is switched on a language selection menu appears Menu language Espa ol Frangais Hrvatski Italiano using cursorupand Magyar down Please select your language e Next e Select your language and follow the on screen instructions to setup the TV Q Tip You can change the menu language or reinstall channels as described in Section 6 Install channels 4 Use yourTV This section helps you perform basic TV operations Instructions on advanced TV opera tions are provided in Section 5 Use more of your TV 4 4 Switch your TV on off or to standby 4 1 1 Switch on your TV LL y If LightGuide 1 is off press POWER on the side of the TV LightGuide flashes during start up turning on completely when your TV is ready for use 4 1 2 Switch off your TV a iO io Law J e Press POWER on the side of the TV Both LightGuide 1 and the standby indicator 2 switch off 4 1 3 Switch your TV to s
30. able management 10 Channel installation 33 Channels Change 12 Favorite lists 25 Child lock 27 Connect Antenna 9 Mains 9 Connections Back 37 Devices 40 Quality 38 Side 38 Demo 36 Electronic Programme Guide 26 Get started 7 Main menus Access 16 Use 16 Overview 5 Photos and music 29 Position 7 Ideal distance 7 Quick access menu Use 17 Remote control Advanced use 14 Basic use 6 Batteries 10 Reset to factory setting 36 Side controls 5 Software update 31 Stand 8 Subtitles 28 Switch Off 11 On 10 11 On from standby 11 To standby 11 Teletext Advanced use 23 Basic use 13 Timers On timer 27 Sleeptimer 27 Volume 12 Wall mount 7 Watch Channels 12 Devices 12 U Uninstall channels 35 USB device Connect 29 Disconnect 29 VESA wall bracket 7 Video formats 47 Volume Adjust 12 21 Automatic leveling 21 Delta 21 Headphone 21 W Wall mount TV 7 Y Y Pb Pr 39 EN 55 ENGLISH PHILIPS 2008 Koninklijke Philips Electronics N V oe AUT REL T 0 313912539362 Document order number 3139 125 39362
31. an antenna connection e Check that the antenna is properly connected to the TV Loud speakers unearthed audio devices neon lights high buildings or mountains can influence the picture quality Try to improve the reception quality by changing the antenna direction or moving devices away from the TV e Verify if the correct TV system is selected for your region See Section 6 2 Manually install channels e f reception on only one channel is poor try to fine tune this channel See Section 6 2 1 Fine tune channels You receive poor picture quality from connected devices e Check that the devices are connected properly Also be sure to assign devices to connectors as described in Section 7 4 1 Assign devices to connectors Verify that picture settings are correctly set See Section 5 3 2 Adjust picture settings The TV did not save my settings Verify that the TV is set to Home mode which offers you complete flexibility to change settings See Section 5 6 Change to Shop or Home mode The picture does not fit the screen it is too big or too small Try using a different picture format as described in Section 5 3 4 Change picture format e Assign your device to connectors as described in Section 7 4 1 Assign devices to connectors The picture position on screen is not correct Picture signals from some devices do not fit the screen correctly Check the signal output of the device 9 4 Sound
32. are trademarks of Dolby Laboratories BBE DIGITAL Manufactured under license from BBE Sound Inc Licensed by BBE Inc under one or more of the following US patents 5510752 5736897 BBE and BBE symbol are registered trademarks of BBE Sound Inc Windows Media is either a registered trademark or trademark of Microsoft Corporation in the United States and or other countries Kensington and Micro Saver are registered US trademarks of ACCO World Corporation with issued registrations and pending applications in other countries throughout the world All other registered and unregistered trademarks are the property of their respective owners 1 Important Congratulations on your purchase and welcome to Philips Read this user manual before you start to use this product Pay close attention to this section and follow the safety and screen care instructions The product warranty does not apply if damage is caused by failing to follow these instructions To fully benefit from the support that Philips offers register your product at www philips com welcome The model and serial number of your TV can be found on the back and side of the TV as well as on the packaging 1 4 Safety Two people are required to lift and carry a TV that weighs more than 25 kilos 551b Improper handling of the TV can result in serious injury f transporting the TV in low temperatures
33. ated This may take several minutes EN 46 6 Note Do not remove the CAM from the slot Removing the CAM will deactivate the digital services 7 6 2 Access CAM services After inserting and activating the CAM press MENU on the remote control and select TV menu gt Features gt Common interface This menu option is only available if the CAM is correctly inserted and activated On screen applications and content are provided by your digital TV service operator 8 Technical specifications Supported display resolutions Computer formats Resolution Refresh rate 640 x 480 60Hz 800 x 600 60Hz 1024 x 768 60Hz 1920 x 1080i 60Hz 1920 x 1080p 60Hz Video formats Resolution Refresh rate 480i 60Hz 480p 60Hz 576i 50Hz 576p 50Hz 720p 50Hz 60Hz 1080i 50Hz 60Hz 1080p 24Hz 25Hz 30Hz 1080p 50Hz 60Hz Tuner Reception Transmission Antenna input 75ohm coaxial IEC75 TV system DVB COFDM 2K 8K Video playback NTSC SECAM PAL DVB Terrestrial see listed countries on the back of the TV Multimedia Connection USB Playback formats MP3 Linear PCM slide show alb JPEG Remote control RCPFO3E08B Batteries 2 x AAA size LRO3 type Connections Rear EXT 1 SCART Audio L R CVBS in out RGB EXT 2 SCART Audio L R CVBS in out RGB e EXT 3 Component Y Pb Audio L R in e HDMI 1 2 3 ENGLISH 6 Note Your TV may have two or t
34. control and select TV menu gt Features gt Child lock and press gt to enter your code 2 Enter your code with the number keys To lock or unlock all channels and connected devices 1 In the Child Lock menu select Lock or Unlock 2 Press OK To lock a programme or all channels from a certain time 1 In the Child lock menu select Custom lock Child lock Custom lock Lock Lock after Custom lock Channel lock Unlock Parental rating 2 Press gt to enter the Custom lock menu rad Press gt again to enter the Lock after menu Select On to enable the Timer lock Press 4 Select Time Press gt Enter the time with A or v and gt Press OK so Oo ND HW To lock one or more channels and connected devices 1 In the Child lock menu select Custom lock 2 Press gt to enter EN 28 3 Press A or to select Channel lock 4 Press gt 5 Press A or Y to select the channel or device you want to lock or unlock 6 At each selection press OK to lock or unlock the channel or device To set parental ratings Some digital broadcasters rate their programmes according to age You can set your TV to display only programmes with age ratings higher than your child s 1 In the Child lock menu select Custom lock Press to enter Press A or v to select Parental rating Press gt Press A or v to select an age rating wo qd DN Press Menu to
35. down the list 5 Press MENU to exit 6 6 Manually update the channel list If your TV is in standby mode an update is performed every morning This update matches channels stored in your channel list with those available from your broadcaster If a channel is unavailable it is automatically removed from the channel list In addition to the automatic update you can manually update the channel list EN 35 1 Press MENU on the remote control and select TV menu gt Installation gt Channel installation gt Installation update 2 Press gt to enter the Installation update menu Start now is highlighted 3 Press OK 4 Press the green key to start the update This may take a few minutes 5 When the update is complete press the red key to return to the Channel installation menu 6 Press MENU to exit 6 7 Test digital reception If using digital broadcasts you can check the quality and signal strength of digital channels This allows you to reposition and test your antenna or satellite dish 1 Press MENU on the remote control and select TV menu gt Installation gt Channel installation gt Digital Test reception 2 Press gt to enter the Digital Test reception menu 3 Press OK 4 Press the green key to automatically start the test or manually enter the frequency of the channel you want to test If the signal quality and strength is poor reposition the antenna or satellite di
36. e colour coded items at the bottom of the screen Tip Press PSP to return to the previously viewed page 3 Press TELETEXT again to switch off teletext Note for UK users only Some digital TV channels offer dedicated digital text services for example BBC1 For advanced information on teletext see Section 5 7 Use advanced teletext features AMBILIGHT eo AMBILIGHT MODE E PHILIPS E TELEVISION Press AMBILIGHT on the remote control Ambilight turns on Press AMBILIGHT again to turn off Ambilight 4 5 1 Change Ambilight mode AMBILIGHT MODE Je MODE PHILIPS TELEVISION 4 5 UseAmbilight Ambilight is an innovative Philips feature that adds reactive ambient lighting to your viewing experience With Ambilight turned on press MODE on the remote control An Ambilight Mode screen appears Press MODE or A to select one of the following Ambilight modes Colour Sets Ambilight to a constant colour Relaxed Sets Ambilight to change soft and smoothly in synch with the images on screen Moderate Sets Ambilight between Relaxed and Dynamic modes Dynamic Sets Ambilight to change quickly and responsively with the images on screen Press OK to activate the Ambilight mode For advanced information on Ambilight see Section 5 4 Adjust Ambilight settings EN 13 5 Use more of yourTV 5 1 Remot
37. e TV is swivelled Strain on the power cord can loosen connections and cause arcing or fire Disconnect the TV from the mains and antenna before lightning storms During lightning storms do not touch any part of the TV mains cord or antenna cable Be sure that you have full access to the mains cord for easy disconnection of the TV from the mains When disconnecting the TV from the mains be sure to Turn off the TV then the mains power if available Unplug the mains cord from the mains socket outlet EN 3 3 Unplug the mains cord from the power connector at the back of the TV Always pull the mains cord by the plug Do not pull the mains cord e Permanent hearing loss can occur if you use earphones or headphones at high volumes Though high volume may sound normal over time it can damage your hearing To protect your hearing limit the amount of time you use earphones or headphones at high volume 1 2 Screen care Turn off and unplug the mains cord before cleaning the screen Clean the screen with a soft dry cloth Do not use substances such as household cleaning agents as these may damage the screen To avoid deformations or colour fading wipe off water droplets as soon as possible Do not touch push rub or strike the screen with hard objects as this may damage the screen permanently e Where possible avoid stationary images that
38. e colour 5 5 Adjust LightGuide brightness 1 Press MENU on the remote control and select TV menu gt Installation gt Preferences gt LightGuide Level 2 Press gt to enter the LightGuide Level menu 3 Use A or v to select the LightGuide brightness 0 Off 1 25 2 50 3 75 4 Full 4 Press OK to confirm 5 Press MENU to exit 5 6 Change to Shop or Home mode 1 Press MENU on the remote control and select TV menu gt Installation gt Preferences gt Location 2 Press gt to enter the Location menu 3 Use A or Y to select the TV mode Shop Sets smart settings to Vivid ideal for a shop environment The flexibility to change settings is limited Home Gives home users the full flexibility to change all TV settings 4 Press OK to confirm 5 Press MENU to exit 5 7 Use advanced teletext features Your TV has a 1 200 page memory that stores broadcasted teletext pages and subpages The teletext memory reduces page loading time 5 7 1 Select teletext subpages A teletext page can hold several subpages Subpages are displayed on a bar next to the main page number 1 Press TELETEXT on the remote control 2 Select a teletext page 3 Press 4 or gt to select a subpage 5 7 2 Select T O P teletext broadcasts Table Of Pages teletext broadcasts allow you to jump from one subject to another without using page numbers T O P teletext is not b
39. e control overview This section provides a detailed overview of This section helps you perform advanced TV remote controll features operations e 1 2 e 11 4 5 6 y 7 9 15 eam S e ol 12 14 d fe AMBILIGHT MODE zi uu 13 PHILIPS TELEVISION EN 14 10 11 12 13 14 15 16 17 18 STANDBY Switches the TV on from standby or back to standby SOURCE Selects connected devices PICTURE FORMAT Selects a picture format SUBTITLE Activates or deactivates subtitles COLOUR KEYS Selects tasks or teletext pages INFO Displays programme information if available OK Accesses the All channels menu or activates a setting NAVIGATION KEYS Up A Down v Left 4 and Right keys navigate the menu OPTION Activates the Quick access menu PROGRAM P Switches to the next or previous channel NUMBER KEYS Selects a channel page or setting PREVIOUS CHANNEL Returns to the previously viewed channel MODE Toggles Ambilight modes AMBILIGHT Switches Ambilight on or off MHEG CANCEL Cancels digital text or interactive services UK only MUTE Mutes or restores sound VOLUME Increases or decreases volume MENU Toggles the menu on or off 19 20 21 22 23 BACK GU
40. exit the Child lock menu 5 11 Use subtitles You can enable subtitles for each TV channel Subtitles are broadcast via teletext or DVB T digital broadcasts With digital broadcasts you have the additional option of selecting a preferred subtitle language 5 11 1 Enable subtitles on analogue TV channels 1 Select an analogue TV channel 2 Press TELETEXT on the remote control 3 Enter the three digit page number of the subtitle page 4 Press TELETEXT to switch off teletext 5 Press MENU on the remote control and select TV menu gt Features gt Subtitle 6 Press gt to enter the list TV menu Features TV settings Subtitle Subtitle language Installation Sleeptimer Software update sr Set Change code On timer Common interface 7 Press A or v to select On to display subtitles always or On during mute to display subtitles only when the sound is muted with the mK key on the remote control 8 Press OK to return to the Features menu Note You must repeat this procedure to enable subtitles on each analogue channel 5 11 2 Enable subtitles on digital TV channels Repeat steps 5 to 8 in Section 5 11 1 Enable subtitles on analogue TV channels 5 11 3 Select a subtitle language on digital TV channels Note When you select a subtitle language on a digital TV channel as described below the preferred subtitle language set in the Installation menu is temporarily o
41. gt to enter the list 5 Press v or A to select the device attached to the connector 6 Press OK to select the device 7 Repeat the procedure until all devices are correctly assigned to connectors 8 Press MENU to exit 7 4 2 Assign the AUDIO IN mini jack connector If you connect audio from a PC to the AUDIO IN mini jack connector at the back of the TV you must associate it to the HDMI connector 1 Press MENU on the remote control and select TV menu gt Installation gt Connections gt Audio In L R Connections AUDIO IN L R EXT 3 HDMI 1 HDMI 2 HDMI 3 Side AUDIO IN L R 2 Press gt to enter the list 3 Press v or A to select the HDMI connector used by the PC 4 Press MENU to exit 7 4 3 Assign a channel decoder Decoders that decode digital channels can be connected to EXT 1 or EXT 2 SCART You have to assign the TV channel as a channel to be decoded Then assign the connection where the decoder is connected 1 Press MENU on the remote control and select TV menu gt Installation gt Decoder gt Channel ENGLISH 2 Press to enter the list 3 Press v or A to select the channel to decode 4 Press 4 and go back to select Status 5 Press w or A to select the connector used by the decoder 6 Press MENU to exit 7 5 Use Philips EasyLink Your TV supports Philips EasyLink which enables one touch play and one touch standby between EasyLink compliant
42. his produces a brilliant high definition image HD Natural Motion Reduces the field and line flicker and reproduces smooth movement especially in movies Set the level to Maximum Minimum or Off Dynamic contrast Enhances the contrast in the picture as the image on the screen changes Set the level to Minimum Medium Maximum or Off Medium is recommended Noise reduction Filters and reduces the noise in the picture Set the level to Minimum Medium Maximum or Off MPEG artefact reduction Smoothens the transitions on digital pictures Switches MPEG artefact reduction On or Off Colour enhancement Makes colours more vivid and improves the resolution of details in bright colours Set the level to Minimum Medium Maximum or Off Active Control Corrects all incoming signals to provide the best picture possible Switches Active control On or Off Light sensor Adjusts picture and Ambilight settings to match lighting conditions in the room Switches Light sensor On or Off Picture format See Section 5 3 4 Change picture format 5 3 3 Use smart settings Apart from manually adjusting picture settings you can use smart settings to set your TV to a predefined picture sound and Ambilight setting 1 Press MENU on the remote control and select TV menu gt TV settings gt Reset smart settings 2 Press gt to enter the list 3 Press A or v to select one of the following settings Current A
43. hree rear HDMI connectors depending on your TV model SPDIF OUT Digital audio out coaxial cinch S PDIF Display synchronised e AUDIO OUT L R Analogue audio out TVANTENNA e AUDIO IN Mini jack audio in for PC DVI HDMI connections Connections Side e Headphone out stereo mini jack e AUDIO in e Video CVBS in S Video USB HDMI Common Interface CAM slot Power Mains power AC 220 240V 10 e Power and standby power consumption See technical specifications at www philips com e Ambient temperature 5 C 35 C Specifications are subject to change without notice For detailed specifications of this product go to www philips com support EN 47 9 Troubleshooting This section describes commonly encountered issues and accompanying solutions 9 1 GeneralTV issues The TV does not switch on Unplug the mains cord wait for one minute and plug in the mains again e Verify that the mains cord is properly connected and that the mains are powered The remote control is not working properly Verify that the remote control batteries are correctly inserted according to the orientation e Replace the remote control batteries if they are flat or weak e Clean the remote control and TV sensor lens The standby light on the TV blinks red Turn off the TV and unplug the mains cord Wait until the TV cools down before reinserting the mains cord and turning
44. issues There is picture but no sound from the TV Note If no audio signal is detected the TV automatically switches off audio output and does not indicate malfunction e Check that all cables are properly connected e Check that the volume is not set to 0 e Check that the sound is not muted There is picture but sound quality is poor e Check Sound settings as described in Section 5 3 5 Adjust sound settings verifying that Stereo selected and Equalizer settings are correct If needed try resetting audio settings to standard There is picture but sound comes from one speaker only e Verify that Balance correctly set as described in Section 5 3 5 Adjust sound settings 9 5 HDMI connection issues You encounter problems with HDMI devices e HDCP support can delay the time taken for TV to display content from a device e If the TV does not recognise the device and the screen displays no picture try switching from one device to another and back again to restart e f you experience intermittent sound disruptions check the user manual of the HDMI device to verify that output settings are correct Alternatively try connecting the audio signal from the HDMI device to the TV via AUDIO IN at the back of the TV e Ifa HDMI to DVI adaptor or HDMI to DVI cable is used check that an additional audio cable is connected to AUDIO IN You must also assign the audio connector as described in Section 7 4 2
45. ital receiver 2 Press SOURCE on the remote control then select the input your digital receiver is connected to 3 Press OK to select the digital receiver 4 Use the remote control of the digital receiver to select TV channels EN 12 4 2 3 Adjust volume EXIT Y T v 11213 Press 1 VOLUME or on the remote control Press VOLUME or on the side controls of your TV Press on the remote control to mute the sound Press again to un mute the sound Note If headphones are connected adjust headphone volume as described in Section 5 3 5 Adjust sound settings You must press the MUTE button on the remote control to mute audio from the TV speakers Pressing VOLUME buttons turns on the TV speakers again 4 3 Watch connected devices 1 Switch on the device 2 Press SOURCE on the remote control then select the input your device is connected to 3 Press OK to select the device 4 4 Use teletext Most TV channels broadcast information via teletext 1 Press TELETEXT on the remote control The main index page appears 2 To select a page with the remote control Enter the page number with the number keys e Press P or a v to view the next or the previous page Press a colour key to select one of th
46. m tint 19 F Factory setting 36 Favorite lists 25 Fine tune channels 35 H HDCP 38 HDMI cable 38 HD Natural Motion 19 Hearing impaired 33 Home mode 23 Hue 18 D Decoder 45 Delta volume 21 Demo 36 Devices Watch 12 Digital Radio 31 Services 46 Teletext 24 Dual I II 21 Dual screen teletext 23 Dynamic contrast 19 K Kensington lock 7 L Language Audio 21 Menus 33 Subtitles 29 LightGuide Adjust brightness 22 Light sensor 19 E Electronic Programme Guide Use 26 Environmental care 4 Equalizer 21 EN 52 M Mains Connect 9 Manual channel installation 34 Menus Child lock 27 Language 33 Main Access 16 Use 16 Quick access Use 17 Teletext menu 24 Mono sound 21 MPEG artefact reduction 19 Mute 15 N Noise reduction 19 On timer 27 P Parental rating 28 Philips EasyLink 45 Photos and music Connect USB device 29 Listen to music 30 View photos 30 View slide show with music 31 Picture Adjust settings Active Control 19 Brightness 18 Colour 18 Colour enhancement 19 Contrast 18 Custom tint 19 Dynamic contrast 19 HD Natural Motion 19 Hue 18 Light sensor 19 MPEG artefact reduction 19 Noise reduction 19 Pixel Plus HD 19 Sharpness 18 Tint 18 Change format 20 Use Settings assistant 18 Use smart settings Current 19 Movie 19 Standard 19 Vivid 19 Pixel Plus HD 19 Position TV 7 Power Connect 9 Q Quick access menu 17 ENGLISH R Radio
47. mmend you use Auto format Movie expand 16 9 Not for HD L Scales the classic 4 3 format to 16 9 Wide screen Stretches the classic 4 3 format to 16 9 Unscaled Only for HD and PC H Maximum sharpness though distortion may appear on borders Also black bars may appear with pictures from your PC 5 3 5 Adjust sound settings This section describes how to adjust sound settings 1 Press MENU on the remote control and select TV menu gt TV settings gt Sound 2 Press gt to enter the list TV settings Sound Settings assistant Reset smart settings MONTE Picture Balance Ambilight Dual I II Mono Stereo Surround mode Headphane volumi v 3 Press A or v to select one of the following settings Equalizer Changes the bass and treble of the sound Select each bar to change a setting Alternatively press the colour keys to select a pre defined equalizer setting Standard Equalizer set to neutral Speech Equalizer settings maximized for speech based audio Multimedia Settings maximized for different audio types Music Settings maximized for music Volume Changes the volume Q Tip To enable or disable the 21 volume bar that appears when you change the volume press MENU on the remote control and select TV menu gt Installation gt Preferences Press to enter the list and select Volume bar on or Volume bar off EN
48. n certain countries With the EPG menu you can e View list of currently broadcast digital programmes View upcoming programmes e Group programmes by genre Set reminders when programmes start Setup preferred EPG channels 5 9 1 Switch on EPG Note The first time you use EPG you may be prompted to perform an update If so follow the on screen instructions 1 Press Q GUIDE on the remote control aztec summ BACK OK gt Alternatively press MENU and select Programme guide The following EPG types appear Now and Next EPG Detailed information about the current programme is displayed EN 26 26 BBC1 Tue 12 Sep 09 17 Title Commonwealth Games Info 7 50 12 30 280 min Exit Next e Press P to change channel Or 7 or 8 day EPG It may take some time to receive 7 or 8 day EPG data When loaded a list of TV programmes is displayed Tue 12 Sep D Programme guide 1 Around 09 55 Next BBC ONE Tweenies The Wright Stuff This is BBC THREE This is BBC THREE This is BBC FOUR This is BBC FOUR Moonlighting Daddio Commonwealth Something Special Trisha Goddard BBC THREE BBC FOUR Remind Watch 13 50 Anastasia Jump to Info 0010 EEN 2 Use the colour keys on the remote control to activate available actions Next
49. n menu press v to select Time zone EN 33 2 Press gt to enter the list 3 Press A or v to select your time zone 4 Press 4 to return to the Installation menu Step 4 Install channels Your TV searches and stores all available digital and analogue TV channels as well as all available digital radio channels 1 In the Installation menu press v to select Channel installation 2 Press gt to enter the Channel installation menu Automatic installation is highlighted 3 Press gt to select Start now 4 Press OK 5 Press the green key to start The installation may take a few minutes 6 When the channel search is completed press the red key to return to the Installation menu 7 Press MENU to exit Q Tip When digital TV channels are found the list of installed channels may display empty channel numbers If you want to rename reorder or uninstall stored channels see Section 6 5 Rearrange channels 6 2 Manually install channels This section describes how to search and store analogue TV channels manually Step 1 Select your system Note Skip to Step 2 Search and store new TV channels if your system settings are correct EN 34 1 Press MENU on the remote control and select TV menu gt Installation gt Channel installation gt Analogue Manual installation Channel install Analogue Manual Automatic install Installation update 327910 Digital Te
50. nectors After connecting your devices be sure to enable them as described in Section 7 4 Setup devices 7 2 1 HDMI Highest quality Jc gt M A HDMI produces the best audio visual quality possible Both audio and video signals are combined in one HDMI cable providing an uncompressed digital interface between your TV and HDMI devices You must use HDMI to experience full high definition video You must also use HDMI cables to enable Philips EasyLink as described in Section 7 5 Use Philips EasyLink Q Tip If your PC only has a DVI connector use a DVI HDMI adaptor to connect your device to a HDMI connector at the back of the TV You must connect a separate audio cable from the device to the AUDIO IN mini jack connector 6 Note Philips HDMI supports HDCP High bandwidth Digital Contents Protection HDCP is a form of Digital Rights Management that protects high definition content in DVD or Blu ray Discs 7 2 2 Component Y Pb Pr Higher quality XX Component Y Pb Pr video provides better picture quality than S Video or composite video connections Though component video supports high definition signals picture quality is lower than HDMI and is analogue When connecting a component video cable match the cable colours to the EXT 3 connectors on the back of the TV Also connect a Audio L R cable to the red and white Audio L R input connectors at EXT 3 7 2 4 S
51. odels or M8 bolts for larger models bolts not supplied 3 3 Connect the antenna cable To connect the mains cord 6 Note The location of the mains connector varies according to TV model ENGLISH Jl 1 Locate the TV ANTENNA connector at the back of the TV 2 Connect one end of an antenna cable not supplied to the TV ANTENNA connector Use an adaptor if the antenna cable does not fit 3 Connect the other end of the antenna UK s EIRE cable to your antenna outlet ensuring that M the cable is tightly secured at both ends 1 Locate the AC IN mains connector at the back or on the bottom of the TV 2 Connect the mains cord to the AC IN 3 4 Connect the mains cord A WARNING 3 Connect the mains cord to the mains Verify that your mains voltage corresponds ensuring that the cord is tightly secured at with the voltage printed at the back of the both ends TV Do not insert the mains cord if the voltage is different EN 9 3 5 Insert the remote control batteries 1 Slide the battery cover off the back of the remote control 2 Insert the two supplied batteries Size AAA Type LRO3 Be sure the and ends of the batteries line up with the markings inside the case 3 Slide the cover back into position 6 Note Remove the batteries if not using the remote control for an extended period of time 3 6 Switch on the TV
52. on the TV If the blinking occurs again contact our Customer Support Centre You forgot your code to unlock Child lock Enter 8888 as described in Section 5 10 3 Lock TV channels or connected devices Child lock The TV menu is in the wrong language See Section 6 1 Automatically install channels for instructions on how to change the TV menu to your preferred language When turning the TV on off to standby you hear a creaking sound from the TV chassis EN 48 No action is required The creaking sound is normal expansion and contraction of the TV as it cools and warms This does not impact performance 9 2 TV channel issues Previously installed channels do not appear in the channel list Verify that the correct list is selected e The channel may have been uninstalled to the Rearrange menu To access the menu press MENU on the remote control and select TV Menu gt Installation gt Channel installation gt Rearrange No digital channels were found during the installation e Verify if the TV supports DVB T in your country See the listed countries on the back of the TV 9 3 Picture issues LightGuide is on but there is no picture Verify if the antenna is connected properly Verify if the correct device is selected There is sound but no picture Verify that picture settings are correctly set See Section 5 3 2 Adjust picture settings You receive poor TV reception from
53. on devices A permanent game console or camcorder can be connected to a HDMI connector or EXT 3 component connectors at the back of the TV 7 3 9 Personal Computer Before connecting the PC Set the PC monitor refresh rate to 60Hz See Section 8 Technical specifications for a list of computer resolutions Change theTV picture format to Unscaled as described in Section 5 3 4 Change picture format To connect a PC to the back of the TV 1 Using a HDMI to DVI cable or a HDMI to DVI adaptor attached to a HDMI cable connect a HDMI connector on the back of your TV to the DVI connector on your PC 2 Connect an audio cable from your PC to the AUDIO IN mini jack connector at the back of the TV EN 44 Note You must assign the AUDIO IN mini jack connector to the HDMI connector as described in Section 7 4 3 Assign the AUDIO IN mini jack connector HDMI3 HDMI2 HDMI I 7 4 Setup devices When all devices are connected you must select the type of device attached to each connector 7 4 1 Assign devices to connectors For easy selection and best signal handling assign the device connected to the connectors on your TV 1 Press MENU on the remote control and select TV menu gt Installation gt Connections Connections 2 Press gt to enter the list 3 Press v or A to select a connector 4 Press
54. paration Balance 3 Press A or v to select one of the following settings Ambilight Switches Ambilight On or Off Brightness Changes the light output of Ambilight Mode Choose from four Ambilight modes Colour Relaxed Moderate Dynamic See Section 4 5 1 Change Ambilight mode Colour Select a pre defined colour setting Warm white Cool white Blue or make a custom colour of your own Note When making a custom colour select Saturation first setting the value high Then select Palette and choose a value between 0 to 100 Separation Sets the level of Ambilight colour on the left and right side of the TV Maximum Medium Minimum and Off levels are available When Off is selected only mono colour Ambilight is displayed Balance Sets the level of Ambilight on the left and right side of the TV EN 22 Caution To avoid poor remote control reception do not place remote control sensors on your devices in range of Ambilight 5 4 1 EnableAmbilight when TV is in standby mode When the TV is in standby mode you can switch on Ambilight to enhance the ambience of your room Ambilight is only available as constant colour in this mode o wo AMBILIGHT MODE PHILIPS TELEVISION 1 Press AMBILIGHT on the remote control when the TV is in standby 2 Press MODE repeatedly to select an availabl
55. pplies manually selected picture sound and Ambilight settings Standard Applies natural picture sound and Ambilight settings suitable for most living room conditions Vivid Applies brilliant picture sound and Ambilight settings suitable for bright surroundings Movie Applies dynamic picture sound and Ambilight settings suitable for a complete cinematic experience 4 Press the green key to store your selection EN 19 ENGLISH 5 3 4 Change picture format Change the picture format to suit your content 1 Press PICTURE FORMAT on your remote control Alternatively press MENU and select TV menu gt TV settings gt Picture gt Picture format Press A or v to select one of the following picture formats Auto format Not for PC Enlarges the picture automatically to fill the screen Subtitles remain visible Note We recommend you use Auto format for minimal screen distortion Super zoom Not for HD Removes the black bars on the side of 4 3 broadcasts with minimal distortion 4 3 Not for HD Displays the classic 4 3 format EN 20 Note Constant use of the 4 3 picture format can cause screen distortion Ve recommend you use Auto format Movie expand 14 9 Not for HD Scales the classic 4 3 format to 14 9 6 Note Constant use of the 14 9 picture format can cause screen distortion VVe reco
56. r gt to select the left or right side to make your choice 6 Press the green key to go to the next setting You will go through several settings When finished you will be prompted to store these settings 7 Press the green key to store all your settings EN 18 5 3 2 Adjust picture settings This section describes how to adjust picture settings 1 Press MENU on the remote control and select TV menu gt TV settings gt Picture TV settings Picture Contrast Reset smart settings 1201775 Settings assistant Sound Ambilight 2 Press gt to enter the list 3 Press A or v to select a setting Contrast Changes the level of bright parts in the picture keeping the dark parts unchanged Brightness Changes the level of light in the picture Colour Changes the level of saturation Hue If NTSC is broadcast this level compensates the colour variations Sharpness Changes the level of sharpness of fine details Tint Sets the colours to Normal Warm reddish or Cool bluish Select Custom to make a setting of your own Custom tint If Custom is selected in the Tint menu follow the on screen instructions to change the value of R WP Red White Point G WP Green White Point B WP Blue White Point R BL Red Black Level G BL Green Black Level Pixel Plus Enables or disables Pixel Plus HD which fine tunes each pixel to match surrounding pixels T
57. remain on screen for extended periods EN 4 of time Examples include screen menus teletext pages black bars or stock market tickers If you must use stationary images reduce the screen contrast and brightness to avoid screen damage 1 3 Environmental care Recycling your packaging The packaging of this product is intended to be recycled Contact your local authorities for information on how to recycle the packaging Disposing your used product Your product is manufactured with high quality materials and components that can be recycled and reused When you see the crossed out wheel bin symbol attached to a product it means the product is covered by the European Directive 2002 96 EC A Do not dispose your used product with household waste Ask your dealer for information on how to safely dispose of the product Uncontrolled waste disposal harms both the environment and human health Disposing used batteries The supplied batteries do not contain mercury or cadmium Dispose supplied and all other used batteries according to your local regulations Power consumption The TV consumes minimal energy in standby mode to minimise environmental impact Active power consumption is displayed at the back of theTV For more product specifications see the product leaflet at www philips com support 2 Your TV This section gives you an overview of commonly used TV controls and functions 2 1
58. remote control The last selected list appears ENGLISH Press the red key to show all favourite lists Press A or v to select a list Press OK CU rw Press the green key to enter Edit mode The selected list displays a full channel list 6 Press A or v to highlight a channel 7 Press OK to mark or unmark the highlighted channel The channel is added to or removed from the selected list 8 Press the green key again to exit Edit mode The modified channel list appears again 5 8 3 Select a channel from a favorite list 1 Press OK on the remote control The last selected channel list appears 2 Use A or v to highlight a channel 3 Press OK The TV tunes to that channel Q Tip gt HOE gt 4 1 2 3 Je4 5 e je 0 9 7 8 9 jo Press PROGRAM on the remote control to scan channels in your selected list e You can select channels not in your list by pressing the number keys EN 25 5 9 Use the Electronic Programme Guide EPG is an on screen guide that displays scheduled digital TV programmes This guide is not available with analogue channels You can navigate select and view programmes by time title or genre There two types of EPG Now and Next and 7 or 8 day EPG Now and Next is always available but the 7 or 8 day EPG is only available i
59. roadcast on all TV channels 1 Press TELETEXT on the remote control Press INFO 2 exe RIS U rr BACK The T O P overview appears ad Use 4 gt or A to select a subject 4 Press OK to view the page 5 7 3 Use dual screen teletext Enabling dual screen teletext displays your channel or source on the left of the screen Teletext is displayed on the right 1 Press GQ DUAL SCREEN on your remote control to enable dual screen teletext 2 Press QB again to display normal teletext 3 Press TELETEXT to switch off teletext 5 7 4 Search teletext Quickly jump to a subject linked to a series of page numbers or search for specific words in teletext pages 1 Press TELETEXT on the remote control 2 Press OK to highlight the first word or number 3 Press A V or 4 gt to jump to the next word or number on the page 4 Press OK to search a page which holds the highlighted word or number 5 Press A until no word or number is highlighted to exit Search EN 23 5 7 5 Enlarge teletext pages For more comfortable reading you can enlarge the teletext page 1 Press TELETEXT on the remote control and select a teletext page 2 Press OPTION on the remote control to enlarge the top part of the page 3 Press OPTION again to view the enlarged lower par
60. sh and retest When complete press the yellow key to store the frequency Press the red key to return to the Channel installation menu Press MENU to exit Note If you have further problems with the EN 36 reception of your digital broadcast contact a specialised installer 6 8 Start a demo 1 Press the red key on the remote control Alternatively press MENU on the remote control and select TV menu gt Features gt Demo Press to enter the Demo menu Select a demo and press OK Press the red key to exit 6 9 Reset TV to factory settings Resetting your TV to factory settings restores default picture and sound settings Channel installation settings remain the same 1 Press MENU on the remote control and select TV menu gt Installation gt Factory settings Press gt to enter the Factory settings menu Reset is highlighted Press OK to reset to factory settings Press MENU to exit 7 Connect devices 7 1 Connection overview ENGLISH 1 EXT RGB ICV 8e SPDIF SERVU of OG i 3 BS ii OOOO COCON CUE AUDIO IN LEFT RIGHT HDMI 1 DVI HDMI 2 DVI HDMI 3 DVI e 15 COMMON INTERFACE Back connectors 1 EXT 1 First SCART connector for DVD players
61. st recept 1 9 Analogue Manual Rearrange Store as new ch 2 Press gt to enter the Channel installation menu System is highlighted 3 Press gt to enter the System list 4 Press A or v to select your country or region 5 Press 4 to return to the Channel installation menu Step 2 Search and store new TV channels 1 Press MENU on the remote control and select TV menu gt Installation gt Channel installation gt Analogue Manual installation gt Search 2 Press gt to enter the Search menu 3 Press the red key and use the number keys on the remote control to manually enter the three digit frequency Alternatively press the green key to automatically search for the next channel 4 Press 4 when the new channel is found 5 Select Store as new channel to store the new channel under a new channel number 6 Press gt to enter 7 Press OK Done appears 8 Press MENU to exit 6 2 1 Fine tune analogue channels You can manually fine tune analogue channels when reception is poor 1 Press MENU on the remote control and select TV menu gt Installation gt Channel installation gt Analogue manual installation gt Fine tune Press gt to enter the Fine tune menu Press A or v to adjust the frequency Press 4 when done wf Ww m Select Store current channel to store the fine tuned channel under the current channel number 6 Press gt to enter 7 Press OK
62. t of the page 4 Press A or v to scroll through the enlarged page 5 Press OPTION again to return to the normal page size 5 7 6 Use the teletext menu With the options in the teletext menu you can reveal hidden information cycle subpages automatically and change the character setting 1 Press TELETEXT on the remote control 2 Press MENU The Teletext menu appears Teletext menu Reveal Off Cycle subpages Off Language Gr Il 3 Press A or v to select an option Reveal Hide or reveal hidden information on a page such as solutions to riddles or puzzles EN 24 Cycle subpages If subpages are available for the selected page you can cycle subpages automatically Language Some languages use a different set of characters If using a different language switch to the appropriate language group to display the text correctly 4 Press OK to change an option 5 Press MENU to exit Teletext menu 6 Press TELETEXT to switch off teletext 5 7 7 Use digital text services UK only Some digital TV broadcasters in UK offer dedicated digital text or interactive services for example BBC1 These services work like normal teletext with the addition of number colour and navigation keys 1 Press TELETEXT on the remote control 2 Press A V or 4 gt to select or highlight items 3 Press one of the colour keys to select an option 4 Press OK to confirm or activate 5 Press
63. tandby Press STANDBY on the remote control LightGuide switches off and the standby indicator switches on red Q Tip Though your TV consumes very little power when in standby energy continues to be consumed as long as the mains remain connected and powered When not in use for extended periods of time switch off and disconnect the TV from the mains 4 1 4 Switch on the TV from standby If the standby indicator is on red press b STANDBY on the remote control 6 Note If you cannot locate your remote control and you want to switch on the TV from standby press POWER on the side of the TV This switches off your TV Press POWER again to switch the TV back on EN 11 ab En U rr 42 WatchTV 4 2 1 Switch channels la RONSE A 1 2 je 4 5 6 je 1 0 L7 8 9 je CaL Te e rar C Press a number 1 to 999 or press P on your remote control Press PROGRAM on the side controls of the TV Press PSP on the remote control to return to the previously viewed TV channel 4 2 2 Switch channels digital receiver E som m ferme amp oI 1 Switch on the dig
64. tated or implied Any operation expressly prohibited in this manual any adjustments or assembly procedures not recommended or authorised in this manual shall void the warranty Pixel characteristics This LCD product has a high number of colour pixels Although it has effective pixels of 99 999 or more black dots or bright points of light red green or blue may appear constantly on the screen This is a structural property of the display within common industry standards and is not a malfunction Open source software This television contains open source software Philips hereby offers to deliver or make available upon request for a charge no more than the cost of physically performing source distribution a complete machine readable copy of the corresponding source code on a medium customarily used for software interchange This offer is valid for a period of 3 years after the date of purchase of this product To obtain the source code write to Philips Consumer Lifestyle Development Manager LoB Mainstream Displays 620A Lorong 1 Toa Payoh Singapore 319762 Compliance with EMF Koninklijke Philips Electronics N V manufactures and sells many products targeted at consumers which like any electronic apparatus in general have the ability to emit and receive electromagnetic signals One of Philips leading Business Principles is to take all necessary health and safety measures for our products to
65. th at least 64MB of storage space Have access to a computer with a USB port and internet access 1 Press MENU on the remote control and select TV menu gt Software update gt Update assistant 2 Select Start now 3 Insert the USB storage device and press the green key An ID file is copied to the USB device 4 Press the green key to finish 5 Connect the USB storage device to your computer 6 In your computer browse to the USB storage device and double click the Update HTML file 7 Follow the on screen instructions to complete the update EN 32 6 Install channels The first time you setup your TY you will be prompted to select an appropriate menu language and to perform automatic installation of all TV and digital radio channels if available This chapter provides instructions on how to reinstall channels as well as other useful channel installation features Note Re installing channels modifies the All channels list 6 1 Automatically install channels This section describes how to search and store channels automatically Instructions are for both digital and analogue channels Step 1 Select your menu language Note Skip to Step 3 Select your time zone if your language settings are correct 1 Press MENU on the remote control and select TV menu gt Installation gt Languages Installation Languages Menu language Time zone Preferred audio
66. verruled 1 Press MENU on the remote control and select TV menu gt Features gt Subtitle language 2 Press gt to enter the list of available languages 3 Press A or v to select a subtitle language 4 Press OK 5 12 View photos and listen to music ENGLISH Connect an external USB storage device and view pictures JPEG format only or listen to music MP3 or Linear PCM formats only 6 Note Philips will not be held responsible if your USB storage device is not supported nor shall Philips accept any liability for damage or loss of stored data 5 12 1 Connect a USB storage device While your TV is on connect your USB storage device to the USB port on the side of your TV The main menu appears automatically and the name of the USB device is highlighted next to Multimedia Television TV menu Channel list Programme guide 6 Note See Section 7 1 Connection overview for a description of the side connectors including the USB port 5 12 2 Disconnect a USB storage device Caution To avoid damaging your USB device always follow the procedure described below when disconnecting 1 Press MENU on the remote control to exit the Multimedia menu 2 Wait five seconds before disconnecting the USB device EN 29 5 12 3 View your photos 1 After connecting your USB storage device to the TV press gt to enter the Multimedia menu Picture is highlighted USB Picture

Philips EIP-4500 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents