Mr. Heater #MH500PT User's Manual
Contents
1. Tank size and tank temperature can directly affect BTU output Assembly Instructions Un assembled Assembled 1 Unpack all the components and inspect for any damage If any damage is discovered contact the delivery service or Mr Heater immediately 2 Connect the hose assembly to the handle assembly and tighten counterclockwise NOTE This is a left handed thread connection Connection to the Supply Tank NOTE The LP Liquid Petroleum gas tank used with this device should be no less than a 20 Ib capacity It should also meet or exceed NFPA 58 Standard for the Storage and Handling of Liquefied Petroleum Gases 1 Inspect the nut nipple excess shut off valve connection of the hose assembly Check for any dents or damage The o ring must be present If damage is found or the o ring is missing call Mr Heater for the proper replacement parts 2 Connect the excess shut off valve end of the host assembly to the shut off valve of a LP gas tank and tighten counterclockwise NOTE If your LP gas tank does not have a shut off valve exchange the tank for one with a shut off valve CAUTION This device is designed for vapor withdrawal from an LP gas tank s ONLY Use of any other gas may result in device failure or personal injury Mr Heater Propane Torch 4 Operating Instructions and Owner s Manual Leak Test 1 Close torch adjusting valve 2 Slowly open the supply tank shut off valve 3 Tes2. the device and stored outdoors in accordance with Chapter 5 of the Standard for the Storage and Handling of Liquefied Petroleum Gases ANSI NFPA 58 CAUTION DO NOT smoke around or expose supply tank s to open flame or sparks Q The hose assembly shall be protected from traffic crushing and hot surfaces This may cause premature wear of the hose DO NOT lift tank by the valve Lifting the tank by the valve may result in damage to the valve NOTE Storage temperature shall not exceed 120degrees F 49 degrees C Place tank on level surface in an upright position Do not invert or lay tank on its side Safety Information Safety publications related to safe practice and use CSA 2 94 U S Requirements for Hand Held LP Torches for use with fuel supply ANSI 249 1 Safety in Welding and Cutting NFPA 54 National Fuel Gas Code NFPA 58 Standard for the Storage and Handling of Liquefied Petroleum Gases Mr Heater Propane Torch 7 Operating Instructions and Owner s Manual Model OPERATING INSTRUCTIONS Mr Heate AND OWNER S MANUAL wnscoer ULLAL WARNING USE ONLY MANUFACTURER S REPLACEMENT PARTS USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH REPLACEMENT PARTS ARE ONLY AVAILABLE DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED SERVICE AGENCY PARTS ORDERING INFORMATION PURCHASING Accessories may be purchased at any Mr Heater local dealer or direct fr
3. OPERATING INSTRUCTIONS Mr Heater AND OWNER S MANUAL MHS500PT READ INSTRUCTIONS CAREFULLY Read and follow all instructions Place instructions in a safe place for future reference Do not allow anyone who has not read these instructions to assemble light adjust or operate this tool Propane Torch Model MH500PT MR HEATER INC 4560 W 160TH ST CLEVELAND OHIO 44135 216 881 5500 04 03 Revision L1 72615 Read and understand instructions before use FOR YOU R SAFETY Retain this information for future reference If you smell gas Shut off gas to the device DO NOT try to light appliance Extinguish any open flame Check the device for leaks using soapy water DO NOT attempt to relight the device until all leaks are repaired and there is no gas smell DO NOT use this device in areas where gasoline or other liquids having flammable vapors are stored or used CAUTION This device is intended for outdoor use only NEVER direct torch flame toward hose or gas tank DO NOT leave torch unattended while in operation DO NOT stand or prop the torch on the burner end while in operation Always use the striker provided Never use a match or lighter to ignite torch DO NOT apply heat or flame to tank to check for leaks or to increase gas pressure DO NOT lift tank by the valve When not in use the gas should be turned off at the LP gas tank s CAUTION In daylight torch flame is barely visible DO NOT pla
4. ce hand or body part in the path of the flame while lighting or operating torch This device is designed for vapor withdrawal from an LP gas tank s ONLY Place tank on level surface in an upright position Do not invert or lay tank on its side Gloves should be worn at all times when operating this device Long sleeves long pants and boots are recommended amp A A amp A A A A A A A N A A A Have an ABC type fire extinguisher readily accessible to the job site THE STATE OF CALIFORNIA REQUIRES THE FOLLOWING WARNING WARNING Combustion by products produced when using this product contain carbon monoxide a chemical known to the State of California to cause cancer and birth defects or other reproductive harm Mr Heater Propane Torch 2 Operating Instructions and Owner s Manual FMH500PT Parts List DESCRIPTION PART NO Handle Assembly Hose Assembly Striker When ordering repair parts always furnish the following information 1 Model Number 2 Part Number 3 Part Description CAUTION Use only genuine Mr Heater replacement parts Never substitute parts Do not use modified parts When ordering replacement parts use the part number located in these instructions Mr Heater Propane Torch 3 Operating Instructions and Owner s Manual OPERATING CHARACTERISTICS Operating Inlet Pressure Temperature Range Range MH500PT 500 000 10 F to 100 F 17 psi to 170 psi
5. h adjusting valve 1 8 of a turn or until you can hear gas escaping 4 Ignite using supplied igniter 5 Use the torch adjusting valve to control the size and heat of flame USE When using tool do not direct flame directly into wind Do not allow barrel to come closer than 6 to the surface being heated Failure to do either of these things could cause flame outage Mr Heater Propane Torch G Operating Instructions and Owner s Manual CAUTION amp DO NOT smoke around or expose supply tank s to open flame or sparks Always use the striker provided Never use a match or lighter to ignite torch Use of device other than the striker may cause personal injury Q DO NOT place hand or any body part in the path of the flame while lighting or operating torch This can result in personal injury Shut Off Instructions 1 Close torch adjusting valve 2 Close supply tank shut off valve 3 Open the torch adjusting valve briefly to release any residual gas left in the hose CAUTION amp DO NOT smoke around or expose supply tank s to open flames or sparks amp Torch end of handle assembly will increase in temperature immediately after shutting off Maintenance Prior to each use 1 Visually inspect all components of the device for damage and or wear If the hose shows excessive abrasion wear or the hose is cut it must be replaced prior to operation If damage is found contact Mr Heater for the proper replacement part
6. om the factory FOR INFORMATION REGARDING SERVICE Please call Toll Free 800 251 0001 www mrheater com Our office hours are 8 30 AM 5 00 PM EST Monday through Friday Please include the model number date of purchase and description of problem in all communication LIMITED WARRANTY Mr Heater Corp warrants its Propane Torch to be free from defects in material and workmanship for a period of 90 days from date of purchase Mr Heater will repair or replace this product free of charge if it has been proven to be defective within the 90 day period and is returned at customer expense with proof of purchase to Mr Heater within the warranty period Mr Heater Inc reserves the right to make changes at any time without notice or obligation in colors specifications accessories materials and models MR HEATER INC 4560 W 160TH ST CLEVELAND OHIO 44135 216 881 5500 Mr Heater is a registered trademark of Enerco Group Inc 2003 Enerco Mr Heater All rights reserved Mr Heater Propane Torch Operating Instructions and Owner s Manual
7. s 2 Visually inspect LP gas tank s for dents damage to collar damage to shut off valve or corroded foot ring If any of these are present the LP gas tank s must be replaced prior to operation 3 Perform a leak test according to the leak test procedure described on page 5 A lgnite torch according to the lighting instructions described on page 5 Check operation of the adjusting valve and the other components prior to proceeding Periodically 1 Remove any debris or combustible material from the torch The torch must be kept clear and free from combustible materials 2 The surface of the device should be cleaned with soap and water Do not use petroleum based or flammable cleaner on any part of the device Disconnecting the Supply Tank 1 Make sure supply tank valve is shut off 2 Open torch adjusting valve briefly to release any residual gas left in the hose Close adjusting valve when complete 3 Disconnect the P O L nut nipple located at the end of the hose assembly from the supply tank s 4 Replace the protective plastic cap and plug to the hose end and supply tank s respectively Mr Heater Propane Torch 6 Operating Instructions and Owner s Manual CAUTION DO NOT smoke around or expose supply tank s to open flames or sparks Storage Never store a torch that is still hot When the torch is stored indoors the connection between the LP gas tank s and the device must be disconnected and the tank s removed from
8. t all connections for possible gas leaks using leak test solution 4 If a leak occurs at e Torch adjusting valve stem Tighten stem packing nut clockwise Slowly open supply tank shut off valve and retest connection Repeat if necessary If leak cannot be stopped by tightening the stem packing nut a new stem assembly part VS 1S may be required Contact Mr Heater for the proper replacement parts e Supply tank shut off valve Close supply tank shut off valve and retighten connection counterclockwise Slowly open supply tank shut off valve and restart connection Repeat if necessary CAUTION DO NOT operate if any leaks are present A leak may create a fire hazard DO NOT smoke around or expose supply tank s to open flames or sparks DO NOT apply heat or flame to tank to check for leaks Excess heat may cause the supply tank to rupture possibly causing personal injury Lighting Instructions NOTE The hose assembly is supplied with an excess flow control valve Opening the supply tank shut off valve rapidly can cause the valve to close If the excess flow valve closes close the supply tank shut off valve Open torch adjusting valve to release any residual gas left in the hose Close torch adjusting valve and wait 30 seconds Slowly open tank shut off valve 1 Make sure torch adjusting valve is closed 2 Open supply tank shut off valve 3 With torch nozzle pointed away from any flammable material open torc
Download Pdf Manuals
Related Search