Lightolier ProSpec IS_26556MCY User's Manual
Contents
1. R LIGHTOLIER a GENLYTE company 631 Airport Road Fall River MA 02720 READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before l installation To prevent electrical shock turn off electricity at fuse box before proceeding Retain these instructions for maintenance reference AAN Fig 3 With SNOOT open accessories can be installed or removed INSTALLING ACCESSORIES Push accessory s into SNOOT snapping them into ACCESSORY SPRINGS NOTE There must always be 1 accessory or clear glass installed in the SNOOT for safety reasons This FIXTURE takes 2 accessories maximum with or without CROSSBLADE REMOVING ACCESSORIES Push ACCESSORIES out of ACCESSORIES SPRING Push one ACCESSORY SPRING against SNOOT if accessory is difficult to remove CROSSBLADE may be removed Pull CROSSBLADE out of SNOOT CLOSE SNOOT OVER LAMP Fig 3 1 Rotate SNOOT until SLOT mates with ACCESS KNOB 2 Tighten ACCESS KNOB to secure SNOOT FIXTURE OPERATION Fig 4 Turn LAMP on or off by activating the switch Fig 2 SETTING HORIZONTAL ROTATION 1 Rotate fixture to desired horizontal position Fixture provides 360 rotation CAUTION There is a STOP that prevents the FIXTURE from being adju2. READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO This fixture is intended for installation in accordance with the National Electrical Code and local regulations To assure full compliance with local codes and regulations check with your local electrical inspector before l S 276556 M CY installation To prevent electrical shock turn off electricity at fuse box before proceeding Retain these instructions for maintenance reference Page 1 of 2 INSTALLATION INSTRUCTIONS FOR ATTACHING AND OPERATING ProSpec TRACK LIGHTING FIXTURE FOR JUNCTION BOX MOUNT CAUTION o Turn off power at fuse box before installing fixture e Fixture temperature is extremely high during operation Use heat resident gloves or other heat resistant materials to protect hands when adjusting or handling the fixture during operation Do not install fixture near combustible materials nae Fixture is not for residential use Neutral Electrical supply to fixture must be 120 volts Electrical supply can be AC or DC e Do not mount fixture on a wall GROUND WIRES INSTRUCTIONS FOR ATTACHING FIXTURE TO J BOX Fig 1 CANOPY is designed for a 4 octagon OUTLET BOX FIXTURE can mount to different OUTLET BOXES as long as box mounting holes are on 3 5 centers and FIXTURE CANOPY covers box completely Box mounting holes should be tapped with 8 32 thread 1 Thread 8 32 STUDS into J BOX STUDS should extend from J BOX at least one in
3. ch 2 WHILE SUPPORTING FIXTURE MAKE CONNECTIONS BLACK FIXTURE LEAD to HOT BLACK SUPPLY LEAD WHITE FIXTURE LEAD to NEUTRAL WHITE SUPPLY LEAD UNINSULATED FIXTURE WIRE is a ground and must be connected to GROUND TERMINAL or GROUND LEAD inside OUTLET BOX Use WIRE NUTS local hardware item Push connections back into OUTLET BOX Push CANOPY against ceiling passing STUDS through holes in CANOPY Make sure wires are not pinched Thread 2 CAP SCREWS onto STUDS Drive CAP SCREWS until CANOPY is tight against the ceiling CAUTION CAP SCREWS must be completely threaded onto the STUDS Or oe NOTE The proper LAMP should be installed into the FIXTURE 3 f ACCESS KNOB 4 prior to energizing See instructions below SWITCH LAMP TERMINAL LAMPING amp USING ACCESSORIES Fig 2 T na Fi RING NOTCH 2 The following lamps may be used in the FIXTURE LAMP ALIGNMENT a go Fixture Cat No 26556M WHCY BKCY BRACKET Lamp 12 Volt PAR 56 Screw Terminal 120 to 240 Watt Holding SNOOT loosen ACCESS KNOB a few turns until LAMP SPRING SNOOT opens Screw SPADE TERMINALS into LAMP TERMINALS Align 3 LAMP BOSSES with 3 RING NOTCHES Align LAMP SCREW TERMINALS with LAMP ALIGNMENT BRACKET Push LAMP into FIXTURE until LAMP SPRINGS hold LAMP i NOTE The 3 LAMP BOSSES must sit in the 3 RING NOTCHES PAME BUSS after the LAMP is installed sii Removing LAMP Snap LAMP out of LAMPSPRINGS Unscrew Fig 2 LAMP TERMINALS i CS iH TOO I
4. sted more than 360 Do not force FIXTUREagainst the STOP Rotate the FIXTURE in the opposite direction to obtain the proper aiming location SETTING VERTICAL ROTATION if 2 3 Loosen SIDE KNOB Turn FIXTURE to desired vertical position The FIXTURE adjust 90 in the vertical direction Do not force past the adjustability limits Tighten SIDE KNOB SETTING LAMP ROTATION fi 2 3 Loosen LAMP ADJUSTMENT KNOB a few turns Drive LAMP ADJUSTMENT KNOB in 1802 slot Tighten LAMP ADJUSTMENT KNOB after LAMP is in desired position SETTING ACCESSORY ROTATION 1 2 3 LIGHTOLIER Loosen ACCESSORY KNOB a few turns Rotate SNOOT to desired position SNOOT rotates 360 Tighten ACCESSORY KNOB HORIZONTAL ROTATION LAMP ROTATION LAMP ADJUSTMENT KNOB AY a ACCESSORIES KNOB Fig 4 INSTRUCTION SHEET NO 26556MCY 0798 Page 2 of 2 ACCESS KNOB ACCESSORIES ACCESSORY SPRING CROSSBLADE VERTICAL ROTATION SIDE KNOB ad S A SNOOT GL Ka ACCESSORIES ROTATION LIGHTOLIER a GENLYTE company 631 Airport Road Fall River MA 02720
Download Pdf Manuals
Related Search