Lenovo S2110A User's Manual
Contents
1. 32 Lenovo IdeaTab S2110A Figure 4 Removal steps of system board Lift the system board in the direction shown by arrow a Disconnect the Vibrator motor connector E Then remove the system board Step Screw guantity Color Torque H M2X2 3L flat head nylok coated 4 Black 1 0 1 5 kgfcm 33 M Lenovo IdeaTab S2110A Hardware Maintenance Manual 1050 LCD For access remove these FRUS in order 1010 Battery pack on page 28 e 1030 Back camera on page 30 1040 System board on page 31 Figure 5 Removal steps of all parts Remove the eleven screws Eg Remove the left speaker module PJ and volume board EJ Be sure to disconnect the connector at the back Peel off the right speaker module EJ Remove the Dock hooks J and D then switch board Efl Step Screw quantity Color Torque H M2X23L flat head nvlok coated 6 Black 1 0 1 5 kgfcm 34 Lenovo IdeaTab S2110A Locations IN Front view El Front camera lenovo 35 M Lenovo IdeaTab S2110A Hardware Maintenance Manual Right side view El Speaker E Volume Top view El Powe2. CRUID CRUID 41 M Lenovo IdeaTab S2110A Hardware Maintenance Manual Trademarks 42 Legend Lenovo Lenovo IAE AH IdeaPad IdeaTab and other Lenovo logos are trademarks of Lenovo in Mainland China and or other countries territories Other product names service names trade names or brands are trademarks of their respective owners Copyright O 2011 Lenovo all rights reserved
3. La bateria de repuesto es una bateria de litio y puede provocar incendios explosiones o quemaduras graves No la recargue ni quite el conector polarizado ni la desmonte ni caliente por encima de los 100 C 212 F ni la incinere ni exponga el contenido de sus celdas al agua Des chela tal como dispone la normativa local y Safety information A Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands immediately wash the affected areas with water at least for 15 minutes Seek medical care if any symptoms caused by the fluid are present after washing Si le panneau d affichage a cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide rincez les abondamment pendant au moins quinze minutes Consultez un m decin si des sympt mes persistent apres le lavage Die Leuchtstoffrohre im LCD Bildschirm enthalt Quecksilber Bei der Entsorgung die rtlichen Bestimmungen fiir Sondermiill beachten Der LCD Bildschirm besteht aus Glas und kann zerbrechen wenn er unsachgema amp behandelt wird oder der Computer auf den Boden f llt Wenn der Bildschirm beschadigt ist und die darin befindliche Fl ssigkeit in Kontakt mit Haut und Augen gerat sollten die betroffenen Stellen mindestens 15 Minuten mit Wasser abgesp lt und bei Beschwerden anschliefend ein Arzt aufgesucht werden Ma NA TON TINA 9971 aav LCD MIN WAN TOM ON Tuna DIDI PO OND
4. A DANGER Before removing any FRU turn off the computer unplug all power cords from electrical outlets remove the battery pack and then disconnect any interconnecting cables Avant de retirer une unite remplacable en client le mettez le syst me hors tension d branchez tous les cordons d alimentation des socles de prise de courant retirez la batterie et d connectez tous les cordons d interface Die Stromzufuhr muf abgeschaltet alle Stromkabel aus der Steckdose gezogen der Akku entfernt und alle Verbindungskabel abgenommen sein bevor eine FRU entfernt wird ONON HN 335 v mud FRU pioro 5309 NOMA NNO un IWNI 929 99 NN piv DIAN MA 5532 PMI 180 ADDON MINA NN MIND V ON Prima di rimuovere gualsiasi FRU spegnere il sistema scollegare dalle prese elettriche tutti i cavi di alimentazione rimuovere la batteria e poi scollegare i cavi di interconnessione FRU TIK DATA ThinkPad DBE WoC CORBA K rv VYRBOALTC HEV KIT AYFV AJ AHEL HEBE TiL TALTS HEV Antes de guitar una FRU apague el sistema desenchufe todos los cables de las tomas de corriente el ctrica quite la bater a y a continuaci n desconecte cualquier cable de conexi n entre dispositivos 13 M Lenovo IdeaTab S2110A Hardware Maintenance Manual Laser compliance statement compliance statement Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD ROM drive ora DVD ROM drive Such devices
5. Checking the battery pack Related service information Passwords Power settings sterne Turning Screen Backlight On Off 23 Lenovo IdeaTab S2110A Specifications 24 FRU replacement notices 26 Screw notices 26 Removing and replacing an FRU 1010 Battery pack 1020 SIM card Micro SD card 1030 Back camera 1040 System board 1050 LCD Locations Front view Right side view Top view Back view ides Left side view Parts list Overall AC adapters USB Cable SD Card Trademarks iii About this manual 0 0 0 0 This manual contains service and reference information for the following Lenovo product Lenovo IdeaTab S2110A Use this manual to troubleshoot problems The manual is divided into the following sections The common sections provide general information guidelines and safety information required for servicing computers e The product specific section includes service reference and product specific parts information Important This manual is intended only for trained servicers who are familiar with Lenovo products Use this manual to troubleshoot problems effectively Before servicing a Lenovo product make sure to read all the information under Safety information on page 1 and Important service information on page 16 Safety information Thi
6. computer password making the computer unusable Sticky keys caused by spilling a liquid onto the keyboard Use of an incorrect AC adapter on laptop products The following symptoms might indicate damage caused by nonwarranted activities Missing parts might be a symptom of unauthorized service or modification If the spindle of a hard disk drive becomes noisy it may have been subjected to excessive force or dropped General checkout Power system checkout system checkout To verify a symptom follow the steps below Turn off the computer Remove the battery pack Connect the AC adapter Make sure that power is supplied when you turn on the computer Turn off the computer Disconnect the AC adapter and install the charged battery pack Make sure that the battery pack supplies power when you turn on the computer I es m p NE If you suspect a power problem see the appropriate one of the following power supply checkouts e Checking the AC adapter on page 21 e Checking operational charging on page 21 e Checking the battery pack on page 22 Checking the AC adapter You are here because the computer fails only when the AC adapter is used If the power on indicator does not turn on check the power cord of the AC adapter for correct continuity and installation e If the computer does not charge during operation go to Checking operational charging To check the AC adapter follow the steps be
7. exploser Akkus enthalten geringe Mengen von Nickel Sie diirfen nicht zerlegt wiederaufgeladen kurzgeschlossen oder Feuer oder Wasser ausgesetzt werden Bei der Entsorgung die rtlichen Bestimmungen f r Sondermiill beachten Beim Ersetzen der Batterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren 5773 9 nog NM 522 199107 MINA 72439 Addon TINA DN p5235 PN OVIT DN DO WI AMIN ISPI IN 0999 IN UND IMIN nupnn p 59 wmo ASADA AION INA 199191 p WANUNI v JD PJN tpm MIINA PRI NWINNNA DPINA NMWAA HIOIDO 2129 MINIMA NI 199194 WWW INON INA AINON 5v MIVINA IN ANSNI DINI La batteria contiene piccole quantita di nichel Non smontarla gettarla nel fuoco o nell acqua n cortocircuitarla Smaltirla secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali Ouando si sostituisce la batteria utilizzare soltanto i tipi inseriti nell appropriato Catalogo parti L impiego di una batteria non adatta potrebbe determinare l incendio o l esplosione della batteria stessa SITU D8vyZiuD EO yvMEREnpCOOET NYT Y RVD VAMUIEU KERO nic ST AZIEU Ya aame ESV No FV Ry ADRECH CH HBB KORE LAI HES C CREW 2 TV NYT k i TALT ARY gt UA RI RYT RETZERLTSTE SW Rolky I ZERTO ST Y BREKUEO RELIEVTSIERSVET Las bater as contienen peque as cantidades de n quel No las desmonte ni recargue ni las eche al f
8. handling ESD sensitive parts Keep the parts in protective packages until they are inserted into the product Avoid contact with other people Wear a grounded wrist strap against your skin to eliminate static on your body Prevent the part from touching your clothing Most clothing is insulative and retains a charge even when you are wearing a wrist strap Use the black side of a grounded work mat to provide a static free work surface The mat is especially useful when handling ESD sensitive devices Select a grounding system such as those listed below to provide protection that meets the specific service requirement Notes The use ofa grounding system to guard against ESD damage is desirable but not necessary Attach the ESD ground clip to any frame ground ground braid or green wire ground When working on a double insulated or battery operated system use an ESD common ground or reference point You can use coax or connector outside shells on these systems Use the round ground prong of the ac plug on ac operated computers Grounding requirements requirements Electrical grounding of the computer is required for operator safety and correct system function Proper grounding of the electrical outlet can be verified by a certified electrician Safety information Safety notices multilingual translations The safety notices in this section are provided in English French German Hebrew Italian Jap
9. live electrical currents Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges Do not use such kind of mat to protect yourself from electrical shock Find the room emergency power off EPO switch disconnecting the switch or electrical outlet If an electrical accident occurs you can then operate the switch or unplug the power cord quickly Do not work alone under hazardous conditions or near the equipment that has hazardous voltages Disconnect all power before Performing a mechanical inspection Working near power supplies Removing or installing main units Before you start to work on the machine unplug the power cord If you cannot unplug it ask the customer to power off the wall box that supplies power to the machine and to lock the wall box in the off position If you need to work on a machine that has exposed electrical circuits observe the following precautions Ensure that another person familiar with the power off controls is near you Attention Another person must be there to switch off the power if necessary Use only one hand when working with powered on electrical equipment keep the other hand in your pocket or behind your back Attention An electrical shock can occur only when there is a complete circuit By observing the above rule you may prevent a current from passing through your body When using te
10. replacing FRUs for replacing FRUs 16 Before replacing parts Make sure that all software fixes drivers and BIOS downloads are installed before replacing any FRUs listed in this manual After a system board is replaced ensure that the latest BIOS is loaded to the system board before completing the service action To download software fixes drivers and BIOS follow the steps below 1 Go to http consumersupport lenovo com 2 Enter a serial number or select a product or use Lenovo smart downloading 3 Select the BIOS Driver Applications and download 4 Follow the directions on the screen and install the necessary software Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs e If you are instructed to replace an FRU but the replacement does not solve the problem reinstall the original FRU before you continue e Some computers have both a processor board and a system board If you are instructed to replace either of them and replacing one of them does not solve the problem reinstall that board and then replace the other one e Ifan adapter or a device consists of more than one FRU any of the FRUs may be the cause of the error Before replacing the adapter or device remove the FRUs one by one to see if the symptoms change Replace only the FRU that changed the symptoms Attention The setup configuration on the computer you are servicing may hav
11. this section carefully before replacing any FRU Screw notices Loose screws can cause a reliability problem In the Lenovo computer this problem is addressed with special nylon coated screws that have the following characteristics e They maintain tight connections They do not easily come loose even with shock or vibration e They are harder to tighten e Each one should be used only once Do the following when you service this machine e Keep the screw kit in your tool bag Always use new screws Usea torque screwdriver if you have one Tighten screws as follows Plastic to plastic Turn an additional 90 after the screw head touches the surface of the plastic part more than 909 Z Cross section e Logic card to plastic Turn an additional 180 after the screw head touches the surface of the logic card more than 180 4 A E ZZ 2 S Cross section e Torque driver If you have a torque screwdriver refer to the Torque column for each step e Make sure that you use the correct screws If you have a torque screwdriver tighten all screws firmly to the torque shown in the table Never use a screw that you removed Use a new one Make sure that all screws are tightened firmly e Ensure torque screwdrivers are calibrated correctly following country specifications Lenovo IdeaTab S2110A Removing and replacing an FRU This section presents exploded figures with
12. with unique FRU part numbers Lenovo plans to transit to RoHS compliance well before the implementation date and expects its suppliers to be readv to support Lenovo s requirements and schedule in the EU Products sold in 2005 and 2006 will contain some RoHS compliant FRUs The following statement pertains to these products and any product Lenovo produces containing RoHS compliant FRUs RoHS compliant FRUs have unique FRU part numbers Before or after the RoHS implementation date failed RoHS compliant parts must alwavs be replaced with RoHS compliant ones so only the FRUs identified as compliant in the system HMM or direct substitutions for those FRUs may be used Products marketed before June 2006 Products marketed after June 2006 Current or Replacement Current or Replacement original part FRU original part FRU Non RoHS Can be Non RoHS Non RoHS Can be RoHS Must be RoHS Must be RoHS Non RoHS Can sub to RoHS RoHS Must be RoHS Note A direct substitution is a part with a different FRU part number that is automatically shipped by the distribution center at the time of the order 18 General checkout General checkout This chapter presents the following information e What to do first on page 20 e Power system checkout on page 21 Before you go to the checkout make sure to read the following important notes Va Important notes Only certified trained personnel can service the computer Before replaci
13. I DOMINA NN VW DPT IN D y DY DINA DPMON ON MNIDI MAY 2395 M9 MINSI mp 15 DOWN INNI DIIVHI IM OY MANA Nel caso che caso l LCD si dovesse rompere ed il liquido in esso contenuto entrasse in contatto con gli occhi o le mani lavare immediatamente le parti interessate con acqua corrente per almeno 15 minuti poi consultare un medico se i sintomi dovessero permanere LCD HL LCD OP ORAM Dit Ficfi r o LIA 18 kO sin tek Zeb IRA ES 15 UG ACL TS ESW BEVEL ERIC Viet IC d o UTD OHKAB OI MORAN CA TES VS Sila LCD se rompe y el fluido de su interior entra en contacto con sus ojos o sus manos lave inmediatamente las reas afectadas con agua durante 15 minutos como m nimo Obtenga atenci n medica si se presenta algun Ns J 11 M Lenovo IdeaTab S2110A Hardware Maintenance Manual 12 Safety notice 6 A DANGER To avoid shock do not remove the plastic cover that protects the lower part of the inverter card Afin d viter tout risque de choc lectrique ne retirez pas le cache en plastique prot geant la partie inf rieure de la carte d alimentation Aus Sicherheitsgr nden die Kunststoffabdeckung die den unteren Teil der Spannungswandlerplatine umgibt nicht entfernen prvvvon nuan NN ondo PN monunnn YI 72 Pann 990937 90 ANNA IPIN DN yan Per evitare scosse elettriche non rimuovere la copertura in plastica che avvolge la parte inferiore della scheda invertitore MBE OI 4 34 A FO FIBERIELTVSZIAFoO
14. POLEAYP MHbIX HEM yKa3aHO 30ECb MOXET MPHBECTH K ONACHOMY PAANALIMOHHOMV O NyyeHnto Pou itie kontr l prav alebo inych vykonani od inych vyrobcov ako je v tomto Specifikovan mohlo by mat za nasledok nebezpe enstvo vystavenia sa vy iarovaniu beet EE LO BUR OPE DO XE El uso de controles o ajustes o la ejecuci n de procedimientos distintos de los aqui especificados puede provocar la exposici n a radiaciones peligrosas Opening the CD ROM drive the DVD ROM drive or any other optical storage device could result in exposure to hazardous laser radiation There are no serviceable parts inside those drives Do not open 14 Safety information A CD ROM drive a DVD ROM drive or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode Note the following la N DANGER Emits visible and invisible laser radiation when open Do not stare into the beam do not view directly with optical instruments and avoid direct exposure to the beam Radiac o por raio laser ao abrir Nao olhe fixo no feixe de luz nao olhe diretamente por meio de instrumentos ticos e evite exposic o direta com o feixe de luz FARAAROCRANI AITAME gt HEA DES FF EE BRE BOWER rh Rayonnement laser si carter ouvert Evitez de fixer le faisceau de le regarder directement avec des instruments optiques ou de vous exposer au rayon Laserstrahlung bei geoffnetem Gerat Nicht direkt oder Ober optisch
15. U was detected Failing FRU name and part number Machine type model number and serial number Customer s name and address Note for warranty During the warranty period the customer may be responsible for repair costs if the computer damage was caused by misuse accident modification unsuitable physical or operating environment or improper maintenance by the customer The following is a list of some common items that are not covered under warranty and some symptoms that might indicate that the system was subjected to stress beyond normal use Before checking problems with the computer determine whether the damage is covered under the warranty by referring to the following list The following are not covered under warranty LCD panel cracked from the application of excessive force or from being dropped Scratched cosmetic parts Distortion deformation or discoloration of the cosmetic parts Plastic parts latches pins or connectors that have been cracked or broken by excessive force Damage caused by liquid spilled into the system Damage caused by the improper insertion of a PC Card or the installation of an incompatible card Improper disk insertion or use of an optical drive Diskette drive damage caused by pressure on the diskette drive cover foreign material in the drive or the insertion of a diskette with multiple labels Damaged or bent diskette eject button Fuses blown by attachment of a nonsupported device Forgotten
16. X NEIE ROT TE EV Para evitar descargas no quite la cubierta de plastico que rodea la parte baja de la tarjeta invertida Safety notice 7 A DANGER Though the main batteries have low voltage a shorted or grounded battery can produce enough current to burn personnel or combustible materials Bien que le voltage des batteries principales soit peu lev le court circuit ou la mise la masse d une batterie peut produire suffisamment de courant pour br ler des mat riaux combustibles ou causer des br lures corporelles graves Obwohl Hauptbatterien eine niedrige Spannung haben k nnen sie doch bei Kurzschluf oder Erdung genug Strom abgeben um brennbare Materialien zu entz nden oder Verletzungen bei Personen hervorzurufen AINO TI nia MIYA YN NPWNAN MIHO W QN MAI PION 09 prono 119799 MINNA IN NASP PIT BAIN nnsn5 IN MMA Sebbene le batterie di alimentazione siano a basso voltaggio una batteria in corto circuito o a massa pu fornire corrente sufficiente da bruciare materiali combustibili o provocare ustioni ai tecnici di manutenzione ju VS TY OBERAE lt Tb va LEV enka yA Mgr EZALETILV UN WASH ISO O TEE A EARD EN ET Aunque las bater as principales tienen un voltaje bajo una bater a cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal Safety information Safety notice 8
17. anese and Spanish 7 Safety notice 1 Before the computer is powered on after FRU replacement make sure all screws springs and other small parts are in place and are not left loose inside the computer Verify this by shaking the computer and listening for rattling sounds Metallic parts or metal flakes can cause electrical shorts Avant de remettre l ordinateur sous tension apres remplacement d une unit p P en clientele v rifiez que tous les ressorts vis et autres pieces sont bien en place et bien fix es Pour ce faire secouez l unite et assurez vous qu aucun bruit suspect ne se produit Des pieces m talliques ou des copeaux de metal pourraient causer un court circuit Bevor nach einem FRU Austausch der Computer wieder angeschlossen wird muf sichergestellt werden daf keine Schrauben Federn oder andere Kleinteile fehlen oder im Geh use vergessen wurden Der Computer mu gesch ttelt und auf Klapperger usche gepr ft werden Metallteile oder splitter k nnen Kurzschl sse erzeugen NTN w FRU NANNA INNI 2WNPN NIYIN 392 DONNA DANN DIOJ DPIN O vsgn 0n 55V NTY5 273 AYNA TINA MI DIVOMN DYN DNPH PPU MPA YPN AWNAN NN 20205 W nt DIN 091899 ON 07999 NINA aav IN OPIN Prima di accendere l elaboratore dopo che stata effettuata la sostituzione di una FRU accertarsi che tutte le viti le molle e tutte le altri parti di piccole dimensioni siano nella corretta posizione e non siano sparse all interno dell elaboratore V
18. anual 1030 Back camera For access remove these FRUS in order 1010 Battery pack on page 28 Figure 3 Removal steps of back camera Detach the back camera connector 11 and remove it 30 Lenovo IdeaTab S2110A 1040 System board Important notices for handling the system board When handling the system board bear the following in mind e Be careful not to drop the system board on a bench top that has a hard surface such as metal wood or composite Avoid rough handling of any kind e In the whole process make sure not to drop or stack the system board e If you put a system board down make sure to put it only on a padded surface such as an ESD mat or conductive corrugated material M Bi For access remove these FRUS in order 1010 Battery pack on page 28 e 1030 Back camera on page 30 31 M Lenovo IdeaTab S2110A Hardware Maintenance Manual Figure 4 Removal steps of sustem board Detach Switch board FPC connector Ef Detach Volume FFC connector El LVDS cable connector n Touch FPC connector H and Speaker connector Dn
19. are also sold separately as options If one of these drives is installed it is certified in the U S to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations DHHS 21 CFR Subchapter J for Class 1 laser products Elsewhere the drive is certified to conform to the requirements of the International Electrotechnical Commission IEC 825 and CENELEC EN 60 825 for Class 1 laser products Ifa CD ROM drive a DVD ROM drive or another laser device is installed note the following 7 A CAUTION Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure O uso de controles ajustes ou desempenho de procedimentos diferentes daqueles aqui especificados pode resultar em perigosa exposic o a radiag o Fife BSW NEAT AA WE Ch ASSP RGR Pour viter tout risque d exposition au rayon laser respectez les consignes de r glage et d utilisation des commandes ainsi que les proc dures d crites Werden Steuer und Einstellelemente anders als hier festgesetzt verwendet kann gefahrliche Laserstrahlung auftreten Az itt el rt elj r sokt l be ll t sokt l s vez rl sekt l elterni a lezersugarzas vesz lye miatt kockazatos L utilizzo di controlli regolazioni o l esecuzione di procedure diverse da quelle specificate possono provocare l esposizione a Ucnonb30BaHue JNEMEHTOB HACTPO KH H BbINONHEHHKHE N
20. brannt werden Auch darf ihr Inhalt nicht mit Wasser in Verbindung gebracht oder der zur richtigen Polung angebrachte Verbindungsstecker entfernt werden Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Beim Ersetzen der Batterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren IN mssonnb 099799 01535 n515y 0997 noo MANDO DN PIVI VINO AMIN NIVO PN nup MM PIIN AMIN DANI IN mx P4999 09 20197 PNI DIJON NN PIWI PIN GEN MIYA 100 hy un VINI 199199 NN povo v 099 xnn JOIN nx UNI IDNA g VANWAI v n 1213n D DP DPN 1991921 UY JMWNAAN DIPINT NMWA NMAMH In IN MD 3295 0175 5125 NINN La batteria di supporto e una batteria al litio e puo incendiarsi esplodere o procurare gravi ustioni Evitare di ricaricarla smontarne il connettore polarizzato smontarla riscaldarla ad una temperatura superiore ai 100 gradi centigradi incendiarla o gettarla in acqua Smaltirla secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali L impiego di una batteria non adatta potrebbe determinare l incendio o l esplosione della batteria stessa FDA RYTY KR BH ETICO ON VES IE TT d DUET aha RVFV OJIE COMETAS DRVAL BYT Y ABD 100 C 212 F U E OJNBL PEKI SERO DA IKE TL LLAT ES Vo 77 Y ERES BATA RARO RMN ES TS HEV MUZ AY DARIA YT ERA UI RE MOR AYT YE BATE LE NIFID MHEKLIEN BPBLIEVTSILBHSVET
21. e been customized Running Automatic Configuration may alter the settings Note the current configuration settings using the View Configuration option then when service has been completed verify that those settings remain in effect Important notice for replacing a system board Some components mounted on a system board are very sensitive Improper handling can cause damage to those components and may cause a system malfunction Attention When handling a system board Do not drop the system board or apply any excessive force to it Avoid rough handling of any kind Avoid bending the system board and hard pushing to prevent cracking at each BGA Ball Grid Array chipset 17 M Lenovo IdeaTab S2110A Hardware Maintenance Manual Important information about replacing RoHS compliant FRUs RoHS The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive 2002 95 EC is a European Union legal requirement affecting the global electronics industrv RoHS requirements must be implemented on Lenovo products placed on the market after June 2006 Products on the market before June 2006 are not required to have RoHS compliant parts If the original FRU parts are non compliant replacement parts can also be non compliant In all cases if the original FRU parts are RoHS compliant the replacement part must also be RoHS compliant Note RoHS and non RoHS FRU part numbers with the same fit and function are identified
22. e Instrumente in den Laserstrahl sehen und den Strahlungsbereich meiden Kinyit skor l zersug r l Ne n zzen bele se szabad szemmel se optikai eszk z kkel Ker lje a sug rnyal bbal val rintkez st Aprendo l unita vengono emesse radiazioni laser Non fissare il fascio non guardarlo direttamente con strumenti ottici e evitare l esposizione diretta al fascio OTKpbIBAA Geperwrecb JIABEPHOFO usnyyeHna He cmoTpuTe Ha nyy He pasT I8AblBA TE ero C NOMOLLBIO ONTM4ECKUX MHOTPVMEHTOB a TAKKE nabera Te npamoro BOSLE CTBUA nasepHoro JIVHA Ked je laserova jednotka otvorena Vyhnite sa priamemu pohladu a nehladte priamo s optickymi nastrojmi do l a a vyhnite sa priamemu vystaveniu l ov HJELP HERB SIET 2G LOW T 0 Ek TE TDLIRUVVESTE EV Radiaci n l ser al abrir No mire fijamente ni examine con instrumental ptico el haz de luz Evite la exposici n directa al haz 15 M Lenovo IdeaTab S2110A Hardware Maintenance Manual Important service information This chapter presents the following important service information e Strategy for replacing FRUs on page 16 Important notice for replacing a system board on page 17 e Important information about replacing RoHS compliant FRUs on page 18 Important BIOS and device driver fixes are customer installable The BIOS and device drivers are posted on the customer support site http consumersupport lenovo com Strategy for
23. e are loose inside the computer Verify this by shaking the computer gently and listening for rattling sounds Metallic parts or metal flakes can cause electrical short circuits Attention The system board is sensitive to and can be damaged by electrostatic discharge Before touching it establish personal grounding by touching a ground point with one hand or using an electrostatic discharge ESD strap P N 6405959 to remove potential shock reasons 27 M Lenovo IdeaTab S2110A Hardware Maintenance Manual 28 1010 Batterv pack N DANGER Only use the battery specified in the parts list for your IdeaTab Any other battery could ignite or explode Figure 1 Removal steps of battery pack Pull out the SIM card slot cover with a fingertip in the direction shown by the arrow E l Open the back cover along the device frame with a flat blade in the direction shown by arrows E Lift the back cover in the direction shown by the arrow Disconnect the battery connector Kl then remove the battery by holding the right edge of the battery pack in the direction shown by the arrow Lenovo IdeaTab S2110A 1020 SIM card Micro SD card Figure 2 Removal steps of SIM card Micro SD card Pull out the SIM card slot cover the card slot cover in the direction shown by arrow H 29 M Lenovo IdeaTab S2110A Hardware Maintenance M
24. endio o l esplosione della batteria stessa TAS TY OMCD ROH TWEED FR VARFENTWS DORE V X3 LEBST PVT V O E RETIRO SO RSE EY a RADO EIR UTTDRW CS REV NYT ABRES S melee HiakosRb ES CA Ts V HORNY VARIA YT erer LTLESW Bok Ay 7 ZENTIS E ASTUR KIEV MHBLIEVTSCERHVET Algunas baterias de reserva contienen una peguefa cantidad de niquel y cadmio No las desmonte ni recargue ni las eche al fuego o al agua ni las cortocircuite Des chelas tal como dispone la normativa local Utilice s lo baterias que se encuentren en la lista de piezas La utilizaci n de una bateria no apropiada puede provocar la ignici n o explosion de la misma Safety information Safety notice 3 A DANGER The battery pack contains small amounts of nickel Do not disassemble it throw it into fire or water or short circuit it Dispose of the battery pack as required by local ordinances or regulations Use only the battery in the appropriate parts listing when replacing the battery pack Use of an incorrect battery can result in ignition or explosion of the battery La batterie contient du nickel Ne la d montez pas ne l exposez ni au feu ni a l eau Ne la mettez pas en court circuit Pour la mettre au rebut conformez vous a la reglementation en vigueur Lorsque vous remplacez la batterie veillez n utiliser que les mod les cit s dans la liste de pi ces d tach es adequate En effet une batterie inappropri e risque de prendre feu ou d
25. erificare ci scuotendo l elaboratore e prestando attenzione ad eventuali rumori eventuali parti o pezzetti metallici possono provocare cortocircuiti pericolosi FRU DISE AY Ua ZOT E AAB BC ML JIR EOD amp 7278 HOST TCIELVMGE DV Era SONU CRA CRW amp ARL TS ES TONER DIA AV ea REIT WF WF LEW LIVED E KN EE ORATI JB ET Antes de encender el sistema despues de sustituir una FRU compruebe que todos los tornillos muelles y dem s piezas peque as se encuentran en su sitio y no se encuentran sueltas dentro del sistema Compru belo agitando el sistema y escuchando los posibles ruidos que provocar an Las piezas met licas pueden causar cortocircuitos el ctricos M Lenovo IdeaTab S2110A Hardware Maintenance Manual Safety notice 2 N DANGER Some standby batteries contain a small amount of nickel and cadmium Do not disassemble a standby battery recharge it throw it into fire or water or short circuit it Dispose of the battery as required by local ordinances or regulations Use only the battery in the appropriate parts listing Use of an incorrect battery can result in ignition or explosion of the battery Certaines batteries de secours contiennent du nickel et du cadmium Ne les d montez pas ne les rechargez pas ne les exposez ni au feu ni l eau Ne les mettez pas en court circuit Pour les mettre au rebut conformez vous la r glementation en vigueur Lorsque vous remplacez la p
26. ile de sauvegarde ou celle de l horloge temps r el veillez n utiliser que les mod les cit s dans la liste de pi ces d tach es ad quate Une batterie ou une pile inappropri e risque de prendre feu ou d exploser Die Bereitschaftsbatterie die sich unter dem Diskettenlaufwerk befindet kann geringe Mengen Nickel und Cadmium enthalten Sie darf nicht zerlegt wiederaufgeladen kurzgeschlossen oder Feuer oder Wasser ausgesetzt werden Bei der Entsorgung die rtlichen Bestimmungen f r Sonderm ll beachten Beim Ersetzen der Bereitschafts oder Systembatterie nur Batterien des Typs verwenden der in der Ersatzteilliste aufgef hrt ist Der Einsatz falscher Batterien kann zu Entz ndung oder Explosion f hren mop Nyaa MON MANDA nnn MID munan 19919 p525 yx OMITA 9779 bv IN UNI AMIN PIN WIND ANN IIVI AINON nu povo v AMN 9877 IN 055 MAP DIFINA mpnn n DN WINI B PINA NIIA WINN 199101 PI VANUNI DIY DION NI NINDI VIDIO ANNAN JASON 5v MININA IN nns DIII Alcune batterie di riserva contengono una piccola quantit di nichel e cadmio Non smontarle ricaricarle gettarle nel fuoco o nell acqua n cortocircuitarle Smaltirle secondo la normativa in vigore DPR 915 82 successive disposizioni e disposizioni locali Quando si sostituisce la batteria dell RTC real time clock o la batteria di supporto utilizzare soltanto i tipi inseriti nell appropriato Catalogo parti L impiego di una batteria non adatta potrebbe determinare l inc
27. ion do not become a victim yourself Switch off the power Send the victim to get medical aid Safety information Safety inspection guide inspection guide The purpose of this inspection guide is to assist you in identifying potential unsafe conditions As each machine was designed and built required safety items were installed to protect users and service personnel from injury This guide addresses only those items You should use good judgment to identify potential safety hazards according to the attachment of non Lenovo features or options not covered by this inspection guide If any unsafe conditions are present you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem Consider these conditions and the safety hazards they present e Electrical hazards especially primary power primary voltage on the frame can cause serious or fatal electrical shock e Explosive hazards such as a damaged CRT face or a bulging capacitor Mechanical hazards such as loose or missing hardware To determine whether there are any potential unsafe conditions use the following checklist at the beginning of every service task Begin the checks with the power off and the power cord disconnected Checklist 1 Check exterior covers for damage loose broken or sharp edges 2 Turn off the computer Disconnect the power cord 3 Check the power cord for a Athird w
28. ire ground connector in good condition Use a meter to measure third wire ground continuity for 0 1 ohm or less between the external ground pin and the frame ground b The power cord should be the type specified in the parts list c Insulation must not be frayed or worn 4 Check for cracked or bulging batteries Remove the cover 6 Check for any obvious non Lenovo alterations Use good judgment as to the safety of any non Lenovo alterations 7 Checkinside the unit for any obvious unsafe conditions such as metal filings contamination water or other liquids or signs of fire or smoke damage 8 Check for worn frayed or pinched cables 9 Check that the power supply cover fasteners screws or rivets have not been removed or tampered with a M Lenovo IdeaTab S2110A Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Anv computer part containing transistors or integrated circuits ICs should be considered sensitive to electrostatic discharge ESD ESD damage can occur when there is a difference in charge between objects Protect against ESD damage by equalizing the charge so that the machine the part the work mat and the person handling the part are all at the same charge Notes 1 Use product specific ESD procedures when they exceed the requirements noted here 2 Make sure that the ESD protective devices you use have been certified ISO 9000 as fully effective When
29. k can charge to 100 of its capacity This protects the battery pack from being overcharged or from having a shortened life To check your battery move your cursor to the Power Meter icon in the icon tray of the Windows taskbar and wait for a moment but do not click it and the percentage of battery power remaining is displayed To get detailed information about the battery double click the Power Meter icon Note If the battery pack becomes hot it may not be able to be charged Remove it from the computer and leave it at room temperature for a while After it cools down reinstall and recharge it To check the battery pack follow the steps below 1 Turn off the computer 2 Remove the battery pack and measure the voltage between battery terminals 1 and 7 See the following figure Terminal Voltage V DC 1 0 to 14 7 Ground 3 If the voltage is less than 11 0 V DC the battery pack has been discharged Note Recharging will be continued for at least 3 hours even though the indicator does not light on If the voltage is still less than 11 0 V DC after recharging replace the battery 4 Ifthe voltage is more than 11 0 V DC measure the resistance between battery terminals 5 and 7 The resistance must be 4 to 30 KQ If the resistance is not correct replace the battery pack If the resistance is correct replace the system board Related service information Related service i
30. lenovo ldeaTab S2110A Hardware Maintenance Manual First Edition September 2011 Copyright Lenovo 2011 All rights reserved LENOVO products data computer software and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C F R 2 101 with limited and restricted rights to use reproduction and disclosure LIMITED AND RESTRICTED RIGHTS NOTICE If products data computer software or services are delivered pursuant a General Services Administration GSA contract use reproduction or disclo sure is subject to restrictions set forth in Contract No GS 35F 05925 2011 Lenovo Contents About this manual ees iv Safety information 1 General safety Electrical safety Safety inspection guide e 5 Handling devices that are sensitive to electrostatic discharge Grounding requirements Safety notices multilingual translations 7 Laser compliance statement 14 Important service information 16 Strategy for replacing FRUS 16 Important notice for replacing a system board sss nr ioe area aleo lar 17 Important information about replacing RoHS compliant FRUS esee 18 General checkout What to do first Power system checkout Checking the AC adapter Checking operational charging
31. low 1 Unplug the AC adapter cable from the computer 2 Measure the output voltage at the plug of the AC adapter cable See the following figure Pin Voltage V DC 1 20 2 0 Note Output voltage for the AC adapter pin No 2 may differ from the one you are servicing 3 If the voltage is not correct replace the AC adapter 4 If the voltage is acceptable do the following e Replace the system board e If the problem continues go to Lenovo IdeaTab S2110A on page 24 Note Noise from the AC adapter does not always indicate a defect Checking operational charging To check whether the battery charges properly during operation use a discharged battery pack or a battery pack that has less than 50 of the total power remaining when installed in the computer 21 M Lenovo IdeaTab S2110A Hardware Maintenance Manual 22 Perform operational charging If the batterv status indicator or icon does not light on remove the batterv pack and let it return to room temperature Reinstall the batterv pack If the charge indicator or icon is still off replace the batterv pack If the charge indicator still does not light on replace the svstem board Then reinstall the battery pack If it is still not charged go to the next section Checking the battery pack Battery charging does not start until the Power Meter shows that less than 95 of the total power remains under this condition the battery pac
32. nformation m This chapter presents the following information Passwords on page 23 Power settings on page 23 Passwords With this option you can decide whether or not your chosen password will be visible as you input it If the checkbox is checked then the password will be visible If it is unchecked then your password will only be displayed as as you input it thereby keeping your password more secure Power settings settings o With these settings you can set Enable Power Efficiency Enable energy saving On energy saving and Energy saving settings Turning Screen Backlight On Off Turning Screen Backlight On In the standby mode you can tap the Power Wake up button on the top of the IdeaTab to wake the screen up The device s screen will then light up indicating that the backlight has been turned on Turning Screen Backlight Off If your IdeaTab is powered on and you do not use it temporarily you can tap the Power Wake up button on its top to turn off the screen backlight Your IdeaTab will enter the standby mode to save power 23 M Lenovo IdeaTab S2110A Hardware Maintenance Manual Lenovo ldeaTabS2110A W This chapter presents the following product specific service references and product specific parts information e Specifications on page 24 e FRU replacement notices on page 26 e Removing and replacing an FRU on page 27 e Locations
33. ng any FRU read the entire page on removing and replacing FRUs When you replace FRUs use new nylon coated screws Be extremely careful during such write operations as copying saving or formatting Drives in the computer that you are servicing sequence might have been altered If you select an incorrect drive data or programs might be overwritten Replace an FRU only with another FRU of the correct model When you replace an FRU make sure that the machine model and the FRU part number are correct by referring to the FRU parts list An FRU should not be replaced just because of a single unreproducible failure Single failures can occur for a variety of reasons that have nothing to do with a hardware defect such as cosmic radiation electrostatic discharge or software errors Consider replacing an FRU only when a problem recurs If you suspect that an FRU is defective clear the error logs and run the test again If the error does not recur do not replace the FRU Be careful not to replace a nondefective FRU 19 M Lenovo IdeaTab S2110A Hardware Maintenance Manual What to do first to do first When you do return an FRU you must include the following information in the parts exchange form or parts return form that you attach to it 20 1 9e NI GI Lp Pe Name and phone number of servicer Date of service Date on which the machine failed Date of purchase Procedure index and page number in which the failing FR
34. on page 35 e Parts list on page 38 Specifications The following table lists the specifications of the Lenovo IdeaTab S2110A 24 Table 1 Specifications Feature Form Factor Size Weight System Platform Memory LCD Integrated Camera Battery Operating System Ports Communication Others Description 259 77mm x 177 97mm x 8 69mm 590g Qualcomm MSM8060A MSM8260A MSM 8660A MSM 8960 1G LP DDR2 10 1 HD LED 1280 x 800 Widescreen view 1 3M on front 5 0M on back 2 cell Li polymer battery Android 3 5mm Combo Audio jack Dock connector compatible with Micro USB Micro SD card slot Micro HDMI Type D jack SIM card slot On select models WLAN Bluetooth 3G WWAN On select models Multi touch supported Built in microphone Stereophonic loudspeakers Compass Gyroscope Lenovo IdeaTab S2110A Table 1 Specifications continued Feature Description MODEM slot e N A Audio e HD Audio 5 1 channel supported via HDMI output WLAN e Tan 802 11 b g n amp combo e Atheros b g n 3G e On select models Bluetooth e BT2 1 EDR Camera e 1 3M HD Front 5M Back Battery e 2 cell Li polymer AC adapter e 5V 10W black Pre installed e Android operating system Subject to actual measurement 25 M Lenovo IdeaTab S2110A Hardware Maintenance Manual I FRU replacement notices l replacement notices 26 This section presents notices related to removing and replacing parts Read
35. r button 36 Lenovo IdeaTab S2110A Back view H Flash BB Back camera lenovo Left side view El Speaker E Combo audio jack EI Micro HDMI port D Micro SD card slot SIM card slot On select models 37 M Lenovo IdeaTab S2110A Hardware Maintenance Manual Parts it A This section presents the following service parts e Overall on page 39 AC adapters on page 41 USB Cable on page 41 SD Card on page 41 Notes e Each FRU is available for all types or models unless specific types or models are specified 38 Lenovo IdeaTab S2110A Overall 39 M Lenovo IdeaTab S2110A Hardware Maintenance Manual 40 Table 1 Parts list Overall o D SI ODI E VID D pe N FRU SYSTEM BOARD VOLUME BOARD SWITCH BOARD SPEAKER MODULE LEFT SPEAKER MODULE RIGHT VOLUME BUTTON BACK CAMERA SWITCH BOARD FPC DOCK HOOK LEFT DOCK HOOK RIGHT Battery LCD MODULE FRU no 90000609 90000676 90000677 90000672 90000673 90201530 90201513 90201517 90201526 90201525 31052540 90400058 CRU ID Z Z Z Z Z Z Z Z Z Z Z Z Lenovo IdeaTab S2110A AC adapters Table 2 Parts list 3 pin AC adapters FRU P N S2 18AW AA 12V1 5A Adapter 36200114 USB Cable Table 3 Parts list USB Cable FRU P N USB CABLE 90201534 SD Card SD SIM Card Slot is available to support SD card
36. s chapter presents the following safety information that you need to get familiar with before you service a Lenovo computer General safety on page 2 Electrical safety on page 3 Safety inspection guide on page 5 Handling devices that are sensitive to electrostatic discharge on page 6 Grounding requirements on page 6 Safety notices multilingual translations on page 7 Laser compliance statement on page 14 M Lenovo IdeaTab S2110A Hardware Maintenance Manual General safety safety Follow these rules below to ensure general safety Observe a good housekeeping in the area where the machines are put during and after the maintenance When lifting any heavy object 1 Make sure that you can stand safely without slipping 2 Distribute the weight of the object equally between your feet 3 Use slow lifting force Never move suddenly or twist when you attempt to lift it 4 Lift it by standing or pushing up with your leg muscles this action could avoid the strain from the muscles in your back Do not attempt to lift any object that weighs more than 16 kg 35 Ib or that you think is too heavy for you Do not perform any action that causes hazards to the customer or that makes the machine unsafe Before you start the machine make sure that other service representatives and the customer are not in a hazardous position Place removed covers and other parts in a safe place keeping them awa
37. sters set the controls correctly and use the approved probe leads and accessories for that tester Stand on suitable rubber mats obtained locally if necessary to insulate you from grounds such as metal floor strips and machine frames Observe the special safety precautions when you work with very high voltages instructions for these precautions are in the safety sections of maintenance information Be extremely careful when you measure the high voltages Regularly inspect and maintain your electrical hand tools for safe operational condition Do not use worn or broken tools and testers Never assume that power has been disconnected from a circuit First check it to make sure that it has been powered off M Lenovo IdeaTab S2110A Hardware Maintenance Manual Alwavs look carefully for possible hazards in your work area Examples of these hazards are moist floors nongrounded power extension cables power surges and missing safety grounds Do not touch live electrical circuits with the reflective surface of a plastic dental mirror The surface is conductive such touching can cause personal injury and machine damage Do not service the following parts with the power on when they are removed from their normal operating places in a machine Power supply units Pumps Blowers and fans Motor generators and similar units This practice ensures correct grounding of the units If an electrical accident occurs Caut
38. the instructions to indicate how to remove and replace the FRU Make sure to observe the following general rules 1 Do not attempt to service any computer unless you have been trained and certified An untrained person runs the risk of damaging parts 2 Before replacing any FRU review FRU replacement notices on page 26 3 Begin by removing any FRUs that have to be removed before the failing FRU Any of such FRUs are listed at the top of the page Remove them in the order in Which they are listed 4 Follow the correct sequence in the steps to remove the FRU as given in the figures by the numbers in square callouts 5 When turning a screw to replace an FRU turn it in the direction as given by the arrow in the figure 6 When removing the FRU move itin the direction as given by the arrow in the figure 7 Toputthenew FRU in place reverse the removal procedures and follow any of the notes that pertain to replacement For information about connecting and arranging internal cables see Locations on page 35 8 When replacing an FRU use the correct screw as shown in the procedures A DANGER Before removing any FRU turn off the computer unplug all power cords from electrical outlets remove the battery pack and then disconnect any of the interconnecting cables Attention After replacing an FRU do not turn on the computer until you have made sure that all screws springs and other small parts are in place and non
39. uego o al agua ni las cortocircuite Des chelas tal como dispone la normativa local Utilice s lo bater as que se encuentren en la lista de piezas al sustituir la bater a La utilizaci n de una bater a no apropiada puede provocar la ignici n o explosi n de la misma M Lenovo IdeaTab S2110A Hardware Maintenance Manual 10 Safety notice 4 N DANGER The lithium battery can cause a fire an explosion or a severe burn Do not recharge it remove its polarized connector disassemble it heat it above 100 C 212 F incinerate it or expose its cell contents to water Dispose of the battery as required by local ordinances or regulations Use only the battery in the appropriate parts listing Use of an incorrect battery can result in ignition or explosion of the battery La pile de sauvegarde contient du lithium Elle pr sente des risques d incendie d explosion ou de br lures graves Ne la rechargez pas ne retirez pas son connecteur polaris et ne la d montez pas Ne l exposez pas une temperature sup rieure 100 C ne la faites pas br ler et n en exposez pas le contenu l eau Mettez la pile au rebut conform ment la r glementation en vigueur Une pile inappropri e risque de prendre feu ou d exploser Die Systembatterie ist eine Lithiumbatterie Sie kann sich entz nden explodieren oder schwere Verbrennungen hervorrufen Batterien dieses Typs d rfen nicht aufgeladen zerlegt ber 100 C erhitzt oder ver
40. y from all personnel while you are servicing the machine Keep your toolcase away from walk areas so that other people will not trip it over Do not wear loose clothing that can be trapped in the moving parts of the machine Make sure that your sleeves are fastened or rolled up above your elbows If your hair is long fasten it Insert the ends of your necktie or scarf inside clothing or fasten it with the nonconductive clip about 8 centimeters 3 inches from the end Do not wear jewelry chains metal frame eyeglasses or metal fasteners for your clothing Attention Metal objects are good electrical conductors Wear safety glasses when you are hammering drilling soldering cutting wire attaching springs using solvents or working in any other conditions that may be hazardous to your eyes After service reinstall all safety shields guards labels and ground wires Replace any safety device that is worn or defective Reinstall all covers correctly before returning the machine to the customer Fan louvers on the machine help to prevent the overheating of internal components Do not obstruct fan louvers or cover them with labels or stickers Safety information Electrical safety safety Observe the following rules when working on electrical equipments Important Use only approved tools and test equipments Some hand tools have handles covered with a soft material that does not insulate you when working with
Download Pdf Manuals
Related Search