LandAirSea Systems GPS Receiver 7100 User's Manual
Contents
1. Black Negative nee Vehicle s Battery 1 4 Mounting the GPS Tracking Unit You can mount the actual GPS tracking unit anywhere in the car It is not recommended to mount the outside of the car because it is not waterproof If you cannot mount the tracking unit inside the vehicle then it is a good idea to make sure that it does not get wet The best place to mount both the unit and the antenna is under the dash board You can usually find a 12 volt power source usually the same source that goes to the radio Make sure the antenna is as high up as possible or in other words as close to the windshield as possible but still under the dash board Also make sure that the black side of the antenna is facing up Shown below are some other otions for antenna placement GPS Tracking Antenna Placement Ratings are in parenthesis Top of roof 1 Under Rear dash or on third brake Under Front Dash 1 light 1 Inside speaker 1 i In gap between window and hood 2 a Inside speaker or under rear dash fabric 1 Under grill 2 Under bug shield Inside rear plastic if present 1 bumper 1 Inside Plastic Bumper 1 Under back or front seat 3 EO Inside Glove Box 2 1 5 Powering Up Your Tracking Unit After you have set the switches connected the power cable without the fuse and mounted the unit and antenna you will be ready to power up the unit Place the fuse back in the fuse holde2. Alternate Style For a more graphical style of zooming in and out and shifting the map panning you can use the alternate style of displaying the vehicle s location See Figure 2 6 Last Known Position Alternate Style Same as above but displays the last known position in an alternate style CONTROL Send Command To send a command to a Unit select the desired Unit in the pull down menu In the Inputs block the inputs show the alias for each input entered while in Edit Unit Settings To Enable Disable a device 0 all inputs or enter the input that corresponds with your particular Unit Switch Output On Off turns selected output On or Off Click Send to initiate command Locate Unit This is the most common function used If you have the unit set up to not send location updates automatically then this is the function you will use to track the vehicle This is commonly called pinging the unit To locate the unit select Locate Unit and click the Locate text on the unit you want to track A message box will come up to confirm your request IMPORTANT After the command is sent you will need to go to Last Known Position and wait for the unit to report its location You may have to click the Update button a few times until you see the updated position Figure 2 6 Alternate Style View in Progress This function will list the commands that you have sent to the unit that have not yet been processed View Commands Sent This fu
3. S8 OFF S6 ON S7 OFF S8 ON S6 ON S7 ON S8 OFF Every 5 Minutes S6 ON S7 ON S8 ON As an example if you have switches 5 6 7 and 8 all in the ON position then the unit will report position only every 5 minutes when the vehicle is moving Web Poll means that the unit will only report its location when you request it by logging in and sending a request to Locate Unit This is commonly knows as pinging the tracking unit 1 4 Connecting the Power Cable to the 7100 Unit and the Vehicle You will need a small screw driver to connect the power cable to the tracking unit Loosen the 2 screws on the side of the unit Insert the wires as shown in the picture below Then tighten the screws Make sure the wires are firmly connected so they do not come loose Black Negative Red Positive Figure 1 0 Power Connection to the LandAirSea 7100 After you have connected the power cable to the tracking unit take the fuse out of the fuse holder The fuse holder is part of the power cable This is VERY important so make sure you do not forget to take the fuse out of the fuse holder Now connect the other end of the power cable to either the battery of the vehicle or the fuse box You can also connect it to any other source on the car that provides 12 volts of power See Figure 1 1 which shows the connection to the battery Red Positive Positive 12 V Figure 1 1 Power Connection vehicle s battery
4. to be monitored such as Air Bag or Car Alarm Output Descriptions In the Output Descriptions type in the output you intend to control such as Shut Off Engine or Unlock Doors Notification Paths The Notification Path is the means you select for an event notifications to be sent These notifications may be received by e mail or alphanumeric page If notification is not selected you can still view all alarms and conditions received from each Unit using the View Data Received function To use cell phone text messaging select e mail and enter the text messaging e mail address into the primary or secondary e mail address block If you do not know the e mail format of your cellular phone we have provided a list under Documentation E mail addresses for Cell Phones Input Notification Control The Input Notification Control allows you to receive notification status Alarms for the inputs set in the Input Description block Select Yes for all inputs entered in the Input Description block Select Yes or No for normal alarm conditions Yes will allow you to receive notifications for normal and alarm conditions Input Notification Text The Input Notification Text will be the text received by you via e mail or alphanumeric page stating the conditions Alarm Normal of the selected inputs In the Alarm Normal text blocks type the condition or notification to be received via e mail or alphanumeric page The Supply Voltage Alarm and Supply V
5. allow session cookies Figure 2 1 Select Tools from the menu then Internet Options then the General tab click Settings and make sure Check for newer versions of stored pages is set to Every visit to the page See Figure 2 2 on the following page Settings Check For newer versions of stored pages Every visit to the page O Every time you start Internet Explorer Automatically O Never Temporary Internet files folder New location C WUTemp Temporary Internet Files Amount of disk space to use J 357 MB Move Folder view Objects Figure 2 2 Netscape 6 select Edit from the menu then Preferences then the Privacy amp Security category click Cookies and make sure Cookie Acceptance Policy is set to either Enable cookies for the originating web site only or Enable all cookies select Edit from the menu then Preferences then the Advanced category click Cache and under Cache Options make sure Compare the page in the cache to the page on the network is set to Every time I view the page 2 2 Logging In You are now ready to log in The website that you go to to log in is www landairsea com On that main web page you will see a link for the Login After you log in you will see a screen similar to he screen on the following page User ID 7970 Name LandAirSea fit Mans F Configures Bh track h Controie GF Documentation E Welcome to LandAirSea Systems To re
6. ed in less than 2 hours You can check on the status of your activation by trying to log in See the section on Log In If you cannot log in than your unit probably has not been activated 1 3 Setting the Switches on the Tracking Unit VERY IMPORTANT DO THIS BEFORE INSTALLATION On the back of the tracking unit you will see eight small switches These switches control how the unit will automatically report its location Make sure this is done before installation For most cases switches 1 2 3 and 4 will not be used and can remain in the off position Later sections of this manual discuss the operation of switches 1 4 Switch 5 controls whether or not the tracking unit will send Speed and Direction information along with the location If you want the unit to report the speed and direction then turn Switch 5 OFF If you only need position more economical then turn Switch 5 ON Switches 6 7 and 8 control how often you want the tracking unit to automatically report its location when the vehicle is moving The unit will not continually send out the location when it is stationary This would waste airtime and dramatically increase the monthly cost The follow ing chart shows which switches to set according to your requirements Web Poll Once per Week Once per Day Every 4 Hours Every Hour Every 30 Minutes Every 15 Minutes S6 OFF S7 OFF S8 OFF S6 OFF S7 OFF S8 ON S6 OFF S7 ON S8 OFF S6 OFF S7 ON S8 ON S6 ON S7 OFF
7. nction will list the commands that you have already sent DOCUMENTATION The items shown under documentation are self explanatory The documentation may or may not be needed depending on you needs
8. oltage Normal is intended for use with a supply that has a backup battery Upon completion click Update List Units This function gives you a list of all the units in your fleet It will also show you when the unit was activated and the last time the units have sent data TRACK View Data Received This function allows you to view all of the data including notifications of your tracking units For most applications this function is not very useful View All Notications This function will show you all of the notifications For most applications this is not used It is only used if you are using the input notifications View E Mail and Alpha Notifications This will show you only the notifications that were sent out via E mail or Pager View Central Station Telco Notifications This is similar to the above description View Central Station I P Notifications This is similar to the above description View Position Fixes View position fixes will show you all of the data points reported for a given time period You can select the time period See Figure Below 4 x Dubuque 7 Figure 2 4 View Position Fixes Appleton Dubuque Gy 2003 GOT Figure 2 5 View Last Known Fleet Position View Last Known Fleet Position This function allows you to view the last known position of your entire fleet This function is very helpful if you need to find the vehicle that is closest to a specific location View Position Fixes
9. px gt IR QEA SYSTEMS INC USER S GUIDE LandAirSea 7100 Real Time GPS Tracking System 1 1 Introduction The LandAirSea 7100 is a web based real time tracking system that uses GPS technology to accurately determine the exact location of your vehicle You can set the unit to update its location while the vehicle is moving and can be set to update in the following increments 5 15 30 60 minutes 4 hours daily or weekly If you do not need the tracking unit to update automatically you can set it up for Web Poll which means you track the location on an as needed basis The unit also has 3 inputs which can be connected to your vehicle s alarm system or airbag inflation system to inform you if your alarm is going off or if your airbag was inflated You can also use the LandAirSea 7100 to disable your vehicle from driving anywhere in the event that it was stolen The LandAirSea 7100 is very easy to install on your vehicle It comes with a single antenna and a power cable that connects directly to your battery or fuse box 1 2 Activating Your LandAirSea 7100 The very first thing you need to do is activate your tracking unit You do not want to have your unit installed before it is activated Activate it first You should have a 7100 Activation sheet that came with your tracking unit Fill it out completely and fax it to the number given on the sheet Within 24 hours your unit will be activated usually activation will be complet
10. r and lock the fuse holder You should see activity on the three green lights located on the top of the unit After about 5 to 10 minutes you should see 1 solid green light and the other 2 lights should flash once about every 5 to 7 seconds You are now ready to log on and track your vehicle Chapter 2 The LandAirSea Real Time Tracking Website 2 1 Required Browser Settings Before you Login to you tracking account there are some important browser setting that you need to set The following instructions are organized according to what browser and browser version you are running Internet Explorer 5 Select Tools from the menu then Internet Options then the Security tab click Custom Level scroll down to Cookies and make sure Allow per session cookies not stored is set to Enable Select Tools from the menu then nternet Options then the General tab click Settings and make sure Check for newer versions of stored pages is set to Every visit to the page Internet Explorer 6 Select Tools from the menu then Internet Options then the Privacy tab click Advanced make sure Override automatic cookie handling is checked and then that Always allow session cookies is checked See Figure 2 1 Advanced Privacy Settings You can choose how cookies are handled in the Internet zone This overrides automatic cookie handling First party Cookies Third party Cookies Accept Accept Block Block Prompt Prompt Always
11. view historical tracking results please click Track To initiate an on demand location please click Control To exit GPS Tracking please logout by clicking Main Should you experience technical difficulties while trying to access information please click Documentation above to review the Required Browser Settings If problems persist please contact our technical support team at 847 462 8078 or email us at Support LandAirSea com LandAirSea Systems Inc 2022 Route 31 McHenry IL 60050 847 462 8078 T 847 594 6038 F Internet Figure 2 3 If your screen does not have a tool bar on the top then you will need to install Java software This can be found at www java com It is a free download called Java for the Desktop and is necessary to properly display the tool bar 2 3 Menu Functions MAI N Logout Login This function allows you to logout or log back in Home This will take you back to the LandAirSea 7100 main page CONFIGURE Edit Unit Settings This area allows you to customize your tracking unit s Select the activated Unit from the pull down menu For most users you do not need to make any changes on this page except naming the unit Under Unit Name type in a name for the vehicle such as Truck1 or GMC1 Fleet If you have a large fleet you can use this feature to divide up your fleet Input Description In the Input Description block enter the type of input conditions
Download Pdf Manuals
Related Search