Humminbird 530516-1_D User's Manual
Contents
1. THE PRODUCTS Some states do not allow limitations on an implied warranty or the exclusion of incidental or consequential damages so the above exclusions may not apply to you You may also have other rights which vary from state to state DOMESTIC USA CUSTOMERS PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE For all technical issues please call 1 800 633 1468 Or visit www humminbird com click SUPPORT Please reference product serial number and model number when contacting Humminbird 4 930516 1_D Contact Humminbird Contact the Humminbird Customer Resource Center in any of the following ways By Telephone Monday Friday 8 00 a m to 4 30 p m Central Standard Time 1 800 633 1468 By e mail typically we respond to your e mail within three business days cservice johnsonoutdoors com For direct shipping our address is Humminbird Service Department 678 Humminbird Lane Eufaula AL 36027 USA ENVIRONMENTAL COMPLIANCE STATEMENT It is the intention of Humminbird to be a responsible corporate citizen operating in compliance with known and applicable environmental regulations and a good neighbor in the communities where we make or sell our products WEEE DIRECTIVE EU Directive 2002 96 EC Waste of Electrical and Electronic Equipment Directive WEEE impacts most distributors sellers and manufacturers of consumer electronics in the European Union The WEEE Directive requires the produ2. and workmanship This warranty is effective for one year from the date of original retail purchase Humminbird products found to be defective and covered by this warranty will be replaced or repaired free of charge at Humminbird option and returned to the customer freight prepaid Humminbird sole responsibility under this warranty is limited to the repair or replacement of a product that has been deemed defective by Humminbird Humminbird is not responsible for charges connected with the removal of such product or reinstallation of replaced or repaired parts This warranty does not apply to a product that has been e mproperly installed e Used in an installation other than that recommended in the product installation and operation instructions e Damaged or has failed because of an accident or abnormal operation e Repaired or modified by entities other than Humminbird Please retain your original receipt as a proof of the purchase date This will be required for in warranty service THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES OBLIGATIONS OR LIABILITIES ON THE PART OF HUMMINBIRD AND WILL BE THE CUSTOMER S EXCLUSIVE REMEDY EXCEPT FOR ANY APPLICABLE IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE IN NO EVENT WILL HUMMINBIRD BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY RELATING TO
3. connector holder on the rear of the fishfinder The slots are keyed to prevent reversed installation so be careful not to force the connector into the holder _ lt coms _ O 2 Carefully pull the excess cable from beneath the mounting surface so the connector holder aligns with the mounting holes on the front of the mounting bracket 3 Snap the support plate to the rear of the connector holder as illustrated 4 Insert the connector holder into place and use the two 6 32 x 3 4 screws to fasten it to the mounting bracket Snap the Support Plate onto Attach the Connector Holder pri the Connector Holder to the Mounting Bracket eo Connector Holder Cable Connector 5 Install the control head by sliding it onto the mounting bracket until it is fully seated To remove the unit simply depress the latch on the rear of the unit and lift i N 6 Ifthe cables pass outside the mounting bracket reinstall the hole cover over the thru hole and fasten e in place using the two 8 x 7 8 wood screws Your fishfinder is now ready for operation Firmly Press Latch to Remove Unit 2008 Humminbird Eufaula AL USA All rights reserved Quick Disconnect Mounting Bracket 1 Year Limited Warranty We warrant the original retail purchaser that products made by Humminbird have been manufactured free from defects in materials
4. Quick Disconnect Mounting Bracket Thank You Thank you for choosing Humminbird America s 1 name in fishfinders Humminbird has built its reputation by designing and manufacturing top quality thoroughly reliable marine equipment Genuine Humminbird accessories offer the opportunity to upgrade and expand the capabilities of your Humminbird product Your Humminbird accessory is designed for trouble free use in even the harshest marine environment In the unlikely event that your Humminbird accessory does require repairs we offer an exclusive Service Policy free of charge during the first year after purchase and available at a reasonable rate after the one year period For complete details see the Warranty section included in this manual Contact our Customer Resource Center at 1 800 633 1468 or visit our website at www humminbird com Installation Overview Following are instructions for the installation of this accessory Before you start installation we encourage you to read these instructions carefully in order to get the full benefit from your Humminbird accessory If you find that any items are missing from your installation kit call our Customer Resource Center at 1 800 633 1468 or visit our website at www humminbird com To install your Quick Disconnect mounting system you will need a drill your control head the mounting bracket the connector holder the power cable the mounting hardware a 9 64 drill bit a 1 h
5. cer of consumer electronics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle WEEE compliance may not be required in your location for electrical amp electronic equipment EEE nor may it be required for EEE designed and intended as fixed or temporary installation in transportation vehicles such as automobiles aircraft and boats In some European Union member states these vehicles are considered outside of the scope of the Directive and EEE for those applications can be considered excluded from the WEEE Directive requirement not be disposed of with other household refuse It must be disposed of and collected for recycling and recovery of waste FEE Humminbird will mark all EEE products in accordance with the WEEE Directive It is our goal to comply in the collection treatment recovery and environmentally sound disposal of those products however these requirement do vary within European Union member states For more information about where you should dispose of your waste equipment for recycling and recovery and or your European Union member state requirements please contact your dealer or distributor trom which your product was purchased This symbol WEEE wheelie bin on product indicates the product must 2008 Humminbird Eufaula AL USA All rights reserved
6. ing the Mounting Holes Set the mounting bracket in place on the mounting surface Mark the four mounting screw locations with a pencil or a punch Set the mounting bracket aside and drill the four mounting holes using a 9 64 drill bit If you have access to the underside of the mounting surface mark and drill a 1 hole centered between the four mounting screw holes Drilling the Mounting Holes Mounting Mounting Hole Hole Locations Locations 7 25 mm Hole Location Route the Cables Through the Mounting Bracket If the cables must pass through a hole directly beneath the mounting bracket mark and drill an additional 1 25 mm hole centered between the four mounting holes Route the cables through the grommet then press the grommet in place around the cables and into the 1 25 mm hole Pass the cables out of the top of the mounting bracket If the cables cannot be routed directly beneath the mounting bracket mark and drill a 1 25 mm hole that will allow you to run the cables close to the bracket Pass the cables through the 1 25 mm hole through the mounting base and out of the top of the mounting bracket Using needle nose pliers break out the tabs on the rear of the mounting base Place the Hole Cover over the mounting surface hole then use it to mark the position of the two mounting screws Remove the Hole Cover drill the two mounting holes using a 9 64 3 5 mm bit fill them with marine grade silicone the
7. n replace the Hole Cover and insert the 8 Phillips countersink wood screws Hand tighten only NOTE Remove the break out tables only if the cable hole is not under the mount Place the mounting bracket on the mounting surface aligned with the drilled holes and fill the mounting holes with marine grade silicone Insert the four 8 Phillips countersink wood screws into the mounting holes Hand tighten only CAUTION Do not cut or shorten the transducer cable and try not to damage the cable insulation Route the cable as far as possible from any VHF radio antenna cables or tachometer cables to reduce the possibility of interference If the cable is too short extension cables are available to extend the transducer cable up to a total of 50 For assistance contact the Customer Resource Center at www humminbird com or call 1 800 633 1468 for more information 2 930516 1_D Route the Cables Through the Mounting Bracket LA Mounting Bracket Route the Cables Through the Hole Not Covered By The Mounting Bracket Break out tabs aam 2008 Humminbird Eufaula AL USA All rights reserved 3 Quick Disconnect Mounting Bracket ers Cable Connector Holder Connecting the Cable Transducer Accessory i Communications Power 1 Insert the cable connector into the appropriate slots of the connector holder The cable connectors are labeled and there are corresponding labels on the
8. ole saw a Phillips and a flat head screw driver an adjustable wrench a level and marine grade silicone sealant Installation Perform the procedures in the following sections to install the Wide Quick Disconnect mounting system on your boat Determine Where to Mount Begin the installation by determining where to mount the control head Consider the following to determine the best location e To check the location planned for the control head test run the cables for power transducer and Temp Speed accessory if applicable e There are two ways to route the cables to the unit through a hole in the mounting surface underneath the mounting bracket or from a hole outside the mounting bracket Routing the cables under the mounting bracket provides maximum weather protection this may not be feasible however if the area under the control head is inaccessible In this case route the cables through a hole at another location and cover with the supplied hole cover e The mounting surface should be stable enough to protect the control head from excessive wave shock and vibration and should provide visibility while in operation e The mounting area should allow sufficient room for the unit to pivot and swivel freely and for easy removal and installation see illustrations 930516 1_D 360 Degree Swivel 2008 Humminbird Eufaula AL USA All rights reserved feb oD Quick Disconnect Mounting Bracket Drill
Download Pdf Manuals
Related Search