Global Machinery Company TS1800 User's Manual
Contents
1. f 7 Use the second spanner supplied to undo the blade bolt by turning it in an anti clockwise direction right hand thread Fig g 8 Take off the outer flange and remove it and the saw blade Fig h 9 Carefully clean the saw blade flanges before fitting the new blade 10 Insert and secure the saw blade in reverse order CAUTION Take note of the direction of blade rotation The cutting edge of the teeth must point in the running direction i e forward refer to the arrow on the saw blade 11 Re fit and re set the riving knife and the saw blade guard 12 Replace the table insert 13 Before using the saw again check that all safety devices are in good working order IMPORTANT After replacing the saw blade make sure the saw blade runs freely by turning the blade by hand 14 Plug the machine into a mains socket and run the saw at no load before using it to cut any materials 16 Maintenance WARNING Always ensure that the tool is switched off and the plug is removed from the power point before making and adjustments or maintenance procedures Power cord maintenance If the supply cord needs replacing the task must be carried out by the manufacturer the manufacturer s agent or an authorised service centre in order to avoid a safety hazard Cleaning 1 Keep the tool s air vents unclogged and clean at all times 2 Remove dust and dirt regularly Cleaning is best done with a soft brush or a2. a heavier duty tool Never use a tool for a purpose for which it was not intended 7 Dress correctly Do not wear loose clothing or jewellery They can be caught in moving parts Rubber gloves and non slip footwear are recommended when working outdoors If you have long hair wear a protective hair covering 8 Use safety accessories Safety glasses and earmuffs should always be worn A face or dust mask is also required if the sanding operation creates dust 9 Do not abuse the power cord Never pull the cord to disconnect the tool from the power point Keep the cord away from heat oil and sharp edges 10 Secure the work piece Use clamps or a vice to hold the work piece It is safer than using your hand and frees both hands to operate the tool 11 Do not overreach Keep your footing secure and balanced at all times 12 Look after your tools Keep tools sharp and clean for better and safer performance Follow the instructions regarding lubrication and accessory changes Inspect tool cords periodically and if damaged have them repaired by an authorised service facility Inspect extension cords periodically and replace them if damaged Keep tool handles dry clean and free from oil and grease 13 Disconnect idle tools Switch off the power and disconnect the plug from the power point before servicing when changing accessories and when the tool is not in use 14 Remove adjusting keys and wrenches Check to see that keys a
3. cuts including longitudinal cuts bevel cuts and mitre cross cuts The below section defines a common list of table saw terms Through Sawing Any cutting operation where the blade extends completely through the thickness of the workpiece Non Through Sawing Any cutting operation where the blade does not extend through the workpiece Rip Cut A cutting or shaping operation made along the length or grain of the workpiece Cross Cut A cut or shaping operation made across the width of the workpiece cutting the workpiece to length Freehand Performing a cut without a fence mitre gauge fixture hold down or other proper device to keep the workpiece from twisting during the cut Kickback An uncontrolled grabbing and throwing of the workpiece back toward the front of the saw Riving Knife Also known as a separator or spreader The riving knife is a metal piece slightly thinner than the saw blade which helps keep the kerf open during cutting operations and prevents kickback Push Stick A device used to feed the workpiece through the saw during narrow ripping type operation and helps keep the operator s hands well away from the blade Push Block A device used for ripping type operations too narrow to allow use of a push stick Push sticks A push stick should always be used if your hand gets within 125mm 5 of the saw blade Handle A push stick is a safety device that helps to keep your hands and fingers away from th
4. faulty component will be repaired or replaced free of charge with another of the same item A small freight charge may apply Proof of purchase is essential We reserve the right to reject any claim where the purchase cannot be verified This warranty does not include damage or defects to the tool caused by or resulting from abuse accidents alterations or commercial or business use lt also does not cover any bonus items or included accessories Only the powertool is covered under this warranty With continuing product development changes may have occurred which render the product received slightly different to that shown in this instruction manual Please ensure that you store your receipt in a safe place Conditions apply to the above warranty For full details of the warranty terms and conditions please refer to our website www gmcompany com For prompt service we suggest you log your service request online www gmcservice com au should you not have access to the internet please contact our service department on 1300 880 001 Australia or 0800 445 721 New Zealand Introduction Your new GMC power tool will more than satisfy your expectations lt has been manufactured under stringent GMC Quality Standards to meet superior performance criteria You will find your new tool easy and safe to operate and with proper care it will give you many years of dependable service CAUTION Carefully read through this entire Ins
5. have been replaced or the fault has been rectified Failure to do so could result in serious personal injury 1 Remove all loose parts from the carton 2 Remove the packing materials from around the saw 3 Carefully lift the saw from the carton and place it on a level work surface Before using the table saw 1 Turn the table top and body upside down on a piece of card to protect the table surface 2 Remove the 6 screws securing the base plate and take off the base plate 3 Take out the polystyrene foam around the motor pack to protect it during transport 4 Replace the base plate and add the 6 screws Know your product Before using the saw familiarise yourself with all the operating features and safety requirements 1 Table top 2 Table insert 3 On off switch 4 Riving knife 5 Saw blade 6 Blade guard 7 Rip fence 8 Rip fence locking lever 9 Rip fence scale 10 Mitre gauge 11 Mitre gauge locking knob 12 Blade height adjustment handle 13 Blade height locking knob 14 Bevel angle locking knob 15 Bevel angle pointer 16 Bevel angle scale 17 Dust extraction port 18 Stand 19 Rubber foot x4 20 Push stick 21 Push stick mounting brackets 22 Blade change spanners x2 23 Hex key dfi ZE ES i m E A JA PP 8 Components The GMC TS1800 is supplied with the following components a N Stand components Legs x 4 mar
6. locking knob onto the shaft at the front of the table saw ensuring that the flat on the inside of the knob locates on the flat at the rear of the shaft Fig 2 Secure the height adjustment knob by tightening the 3 Tighten the height adjustment locking knob Phillips head screw Fig J 4 Using the hex key provided loosen the two hex bolts on the riving knife clamp and insert the riving knife between the two metal plates that form this clamp Fig O 5 Adjust the position of the riving knife so that the gap between the knife and the teeth of the blade is even along the curve of the blade and is not less than 5mm wide Fig P Af 3 Fit the height adjustment handle onto the shaft ensuring that the flat on the handle locates onto the flat at the front of the shaft Fig K 4 Secure the height adjustment handle by tightening the Phillips head screw Fig L y 6 Tighten the 2 hex screws to secure the riving knife in position 7 Replace the table insert and secure using the 8 screws Fitting the blade guard 1 Remove the hex nut and washer on the side of the guard Fig Q 2 Remove the screw from Fitting the riving knife within the guard 1 Remove the 8 screws securing the table insert and take 3 Place the blade guard over the off the table insert Fig M riving Knife so that the hole in 2 Loosen the height adjustment locking knob and turn the the guard and the hole in the riving knife are
7. to fit replacement parts Additional safety rules for table saws Always pull the plug out of the power socket before adjusting or servicing the machine Give these safety regulations to all persons who work on the machine Do not use this saw to cut firewood CAUTION Hands and fingers may be injured on the rotating saw blade Before you use the machine for the first time check that the voltage marked on the rating plate is the same as your mains voltage If you need to use an extension cable make sure its conductor cross section is large enough for the saw s power consumption Minimum cross section 1 0mm Do not use or leave the saw in the rain and never use it in damp humid or wet conditions Provide good lighting Never saw near combustible liquids or gases Wear suitable work clothes Loose garments or jewellery may become caught up in the rotating saw blade Operators have to be at least 18 years of age Trainees of at least 16 years of age are allowed to use the machine under supervision Keep children and infirm people away from the machine when it is connected to the power supply Check the power cord Never use a faulty or damaged power cord If the cordset is damaged take the saw to an authorised service centre for repair or replacement Never attempt any repairs yourself always take it to an authorised service centre for repair or parts replacement Keep the saw table and your workplace clean of woo
8. Fig W 2 Turning the handle anti clockwise increases the cutting depth 3 Turning the handle clockwise decreases the cutting depth Adjusting the blade angle Loosen the bevel angle knob and using the height adjustment locking knob push the blade assembly to the left or right until the pointer points to the required angle on the bevel scale Fig X 2 Retighten the bevel angle knob once the required setting is reached 3 The blade angle pointer can be adjusted when checking the accuracy of the blade angle With the power disconnected place a set square against the saw blade Adjust the blade angle until the blade is parallel to the set square then move the pointer to 0 on the blade angle scale Using the rip fence 1 Use the rip fence when making longitudinal cuts 2 The rip fence is fitted to the table top on either side of the blade Fig Y h 3 Lift the rip fence locking lever and slide the fence to the required position Use the scale as a guide for the distance between the blade and the rip fence Fig Z 4 Retighten the fence locking lever Using the mitre gauge 1 Slide the mitre gauge into the slot of the table top on the left or right hand side of the blade Fig a 2 Loosen the locking knob on the mitre gauge Fig b 3 Rotate the mitre gauge to select the required angle 4 Re tighten the locking knob Operation The table saw can be used to make a variety of
9. Yoo gt Bo TABLE SAW TSI600 INSTRUCTION MANUAL k P m A hy Warranty Introduction Environmental protection Description of symbols Specifications General safety instructions Additional safety rules for table saws Unpacking Before using the table saw Know your product Components Assembling the stand Fitting the table saw to the stand Fitting the push stick mounting brackets Fitting the height adjustment handle and locking knob Fitting the riving knife Fitting the blade guard Dust extraction Turning on and off Adjusting the cutting depth Adjusting the blade angle Using the rip fence Using the mitre gauge Operation Push sticks Kickback Tips to avoid kickback Making longitudinal cuts Cutting a narrow workpiece Cutting an extremely narrow workpiece Making bevel cuts Making cross cuts Changing the saw blade Maintenance Power cord maintenance Cleaning General inspection N 4 GI R GO GO GO N Warranty Power Tools Whilst every effort is made to ensure your complete satisfaction with this tool occasionally due to the mass manufacturing techniques a tool may not live up to our required level of performance and you may need the assistance of our service department This product is warranted for a 2 year period for home domestic use from the date of the original purchase If found to be defective in materials or workmanship the tool or the offending
10. a saw table to prevent the blade from grabbing the work When cutting round wood use clamps that prevent the work piece from turning on the table There must be no nails or other foreign bodies in that part of the work piece you want to cut Always stand to the side of the saw blade when working with the saw Never load the machine so much that it slows down and over heats Never saw several work pieces simultaneously Use the push stick provided with the tool when cutting along or across narrow work pieces Never remove loose splinters chips or jammed pieces of wood when the saw blade is running To rectify faults or remove jammed pieces of wood always switch off the machine first and remove the mains plug Adjustments measurements and cleaning jobs are to be performed only when the motor is switched off and the mains plug removed Before you switch on the machine check that all wrenches and adjustment tools have been removed When you leave your workplace switch off the motor and pull out the power plug All guards and safety devices have to be refitted immediately after completion of any repairs or maintenance It is imperative to observe the accident prevention regulations in force in your area as well as all other generally recognised rules of safety The machine may be used in closed room only in conjunction with a suitable vacuum extraction system This table saw must be connected to a 230 240V socket outlet wi
11. aligned Fig R blade height adjustment handle to raise the blade to ts 4 Insert the screw through the hole and secure using the highest position Fig N nut and flat washer Fig S 11 5 Tighten the nut sufficiently so that the guard rests on the table top but will lift when the workpiece is pushed into the blade Note The blade guard should return to its rest position after the workpiece has been cut CAUTION The saw blade guard must be in position at all times to prevent contact with the blade It should lift up and onto the workpiece when the workpiece is passed through the saw Dust extraction 1 A suitable dust extraction system or household vacuum cleaner can be connected to the dust extraction port for a cleaner working environment Fig T Turning on and off 1 To turn the table saw ON press the green push button marked I Fig U 2 To turn the table saw OFF press the red push button marked O Fig V Note This saw is fitted with an electromagnetic switch In the case where the power supply is turned off to the saw the saw must be turned on by pressing the green ON button after the power supply is reconnected 12 Adjusting the cutting depth WARNING The height locking knob must be loosened before the blade height is adjusted and re tightened once the desired setting is reached 1 Set the saw blade to the required cutting depth by turning the height adjustment handle
12. d scrap and any unnecessary objects Keep the area free of tripping hazards Persons working with the machine should not be distracted Note the direction of rotation of the motor and saw blade After you have switched off the motor never slow down the saw blade by applying pressure to its side Fit only blades which are well sharpened and have no cracks or deformations The machine is to be operated only with a saw blade from a reputable supplier Faulty saw blades have to be replaced immediately Never use saw blades which do not comply with the data specified in this manual Make sure that the arrow on the saw blade complies with the arrow marked on the machine Never dismantle the machine s safety devices or put them out of operation Damaged or faulty safety devices have to be replaced immediately Never cut a work piece which is too small to hold securely If you are interrupted when operating the saw complete the process and switch off before looking up Periodically check that all nuts bolts and other fixings are properly tightened Do not store materials or equipment above a machine in such a way that they could fall into it Always ensure that your work is on the table Never use the tool to cut pieces that are not on the table Do not place your hands in awkward positions where one or both may slip suddenly and touch the saw blade When working with a long work piece use an additional support such as
13. e saw blade A handle helps to apply pressure to the workpiece whilst a notch at the front of the push stick fits onto the edge of the wood to help push it through the saw A push stick can be easily made from a scrap piece of material The push stick must be narrower than the workpiece Please refer to the diagram which depicts a push stick Fig c Kickback Kickback occurs when the blade stalls or binds kicking the workpiece back towards the front of the saw Kickback can cause serlous injury Precautions must be taken to avoid kickback The following conditions can cause kickback and should be avoided Making a cut with the incorrect blade depth Attempting to saw through knots or nails in the workpiece Notch to help push wood Notch to help prevent hand from slipping Twisting the wood while making a cut Failing to correctly position the riving Knife Making a cut with a dull gummed up or improperly set blade Failing to support large workpieces Forcing the workpiece through the saw blade Cutting warped or wet lumber Not following correct operating procedures Using the wrong blade for the type of cut Tips to avoid kickback 1 Always use the correct blade depth setting The top of the blade teeth should clear the workpiece by 3mm to 6mm 2 Inspect the workpiece for knots or nails before beginning a cut Knock out any loose knots with a hammer Never saw into a loose knot or nail 3 Make st
14. ked A Short upper braces x 2 marked B Long upper braces x 2 marked C Long middle braces x 2 marked E Short middle braces x 2 marked F mo 5 8 Height adjustment handle Height adjustment locking knob Blade guard Riving knife Rip fence Push stick mounting brackets x 2 Blade change spanner x 2 Carriage bolt with spring washer Table saw body fitted with carbide tipped saw blade Mitre gauge e Phillips head screws and washers x 4 Push stick 5mm Hex key Rubber feet x 4 flat washer and nut x 32 65mm hex head bolt with 2 flat washers s spring washer and nut x 2 EJ REGA 90mm hex head bolt 893582233333 with 2 flat washers 0090960660000 e spring washer and nut x 2 888666690900 oo e 0000066660000 oo Coo 000066660000 6 6 00 0009006660000 Assembling the stand CAUTION Always pull out the mains power plug before carrying out any maintenance conversion or assembly work on the table saw When assembling the stand it is recommended that the screws are only lightly tightened until the stand is fully assembled Use four carriage bolts spring washers flat washers and nuts s to fit a short middle brace q between two stand legs m Fig A 2 Connect a second short middle brace q to the second pair of stand legs m 3 Use eight carriage bolts spring washers flat washers and nuts s to fit the remaini
15. nd adjusting wrenches are removed from the tool before switching on 15 Avoid unintentional starting Always check that the switch is in the OFF position before plugging in the tool to the power supply Do not carry a plugged in tool with your finger on the switch 16 Use outdoor rated extension cords When a tool is used outdoors use only extension cords that are intended for outdoor use and are so marked 17 Stay alert Watch what you are doing Use common sense Do not operate a power tool when you are tired 18 Check for damaged parts Before using a tool check that there are no damaged parts If a part is slightly damaged carefully determine if it will operate properly and perform its intended function Check for alignment of moving parts binding of moving parts breakage of parts proper mounting and any other conditions that may affect the operation of the tool A part that is damaged should be properly repaired or replaced by an authorised service facility unless otherwise indicated in this Instruction Manual Defective switches must be replaced by an authorised service facility Do not use a tool if the switch does not turn the tool on and off correctly 19 Guard against electric shock Prevent body contact with grounded objects such as water pipes radiators cookers and refrigerator enclosures 20 Use only approved parts When servicing use only identical replacement parts Use an authorised service facility
16. ng the fence into the saw blade 8 Guide the workpiece at the side with your left hand only as far as the front edge of the guard hood 9 Always push the workpiece through to the end of the riving Knife 10 Leave the off cuts on the saw table until the saw blade has stopped again 11 Secure a long workpiece against sagging at the end of the cutting operation e g with a roller stand or similar device 12 Use the push stick for guiding the workpiece if your hand gets to within 125mm 5 of the saw blade 13 After using the push stick place it back on the holder Cutting a narrow workpiece Longitudinal cuts in a workpiece smaller than 125mm 5 in width must always be made with the help of the push stick WARNING Worn or damaged push sticks must be replaced immediately Cutting an extremely narrow workpiece Longitudinal cuts in an extremely narrow workpiece with a width of 30mm or less must always be made with the help of a push block This table saw is not supplied with a push block Either make or purchase a suitable one from a specialist dealer WARNING Worn push blocks must be replaced without delay Making bevel cuts 1 Always use the fence when cutting bevels 2 Set the saw blade to the required angle using the bevel adjustment knob 3 Set the fence to suit the width and height of the workpiece 4 Carry out the cut in accordance with the workpiece width Making cross cuts WARNING When cross cu
17. ng two long middle braces p Fig B 4 Use four carriage bolts spring washers flat washers and nuts s to attach each short upper brace n to the top of the stand Fig C 5 Use four carriage bolts spring washers flat washers and nuts s to attach each long upper brace o to the top of the stand Fig D 6 Add a rubber foot r to the base of each stand leg m FIG E 7 Tighten all bolts and place the stand on its feet h Fitting the table saw to the stand 1 Make sure the blade is completely retracted into the table top 2 Align the holes on the stand with the matching holes in the base of the table saw the holes at the front of the table top are further apart than the holes at the back of the table saw housing 3 Secure the front of the table saw to the stand using 2 65mm hex head bolts with 2 flat washers spring washer and nut t Fig F 4 Secure the rear of the table saw to the stand using 2 50mm hex head bolts with 2 flat washers spring washer and nut u Fig G 5 Fully tighten all screws and nuts Fitting the push stick mounting brackets 1 Fit the 2 push stick mounting brackets to the right hand side of the table saw 2 Use 2 Phillips head screws and washers i to attach each mounting bracket Fig H 3 Slide the push stick into the brackets to hold it in position Fitting the height adjustment handle and locking knob 1 Fit the height adjustment
18. otential hazards Children and infirm people must not use this tool Children should be supervised at all times if they are in the area in which the tool is being used It is also imperative that you observe the accident prevention regulations in force in your area The same applies for general rules of occupational health and safety WARNING When using power tools basic safety precautions should always be taken to reduce the risk of fire electric shock and personal injury Also please read and heed the advice given in the additional important safety instructions 1 Keep the work area clean and tidy Cluttered work areas and benches invite accidents and injury 2 Consider the environment in which you are working Do not use power tools in damp or wet locations Keep the work area well lit Do not expose power tools to rain Do not use power tools in the presence of flammable liquids or gases 3 Keep visitors away from the work area All visitors and onlookers especially children and infirm persons should be kept well away from where you are working Do not let others in the vicinity make contact with the tool or extension cord 4 Store tools safely When not in use tools should be locked up out of reach 5 Do not force the tool The tool will do the job better and safer working at the rate for which it was designed 6 Use the correct tool for the job Do not force small tools or attachments to do the job best handled by
19. rag 3 Re lubricate all moving parts at regular intervals 4 Never use caustic agents to clean plastic parts CAUTION Do not use cleaning agents to clean the plastic parts of the saw A mild detergent on a damp cloth is recommended General inspection Regularly check that all the fixing screws are tight They may vibrate loose over time GMC customer assist For prompt service we suggest you log your service request online at www gmcservice com au Should you not have access to the Internet please contact our service department on 1300 880 001 Australia or 0800 445 721 New Zealand 7am 7pm 7days a week AEST You will need the following details at hand to log your service request Personal details First 8 Last name address pick up address contact phone numbers email address Product details Product number date of purchase retailer bought from State 4 postcode receipt number reason for the request copy of official purchase receipt Attach your purchase receipt and save with this Manual for future reference Please refer to our website www gmcompany com for full GMC warranty Terms and Conditions
20. raight cuts Always use the rip fence when rip cutting This helps prevent twisting the wood in the cut 4 Always use clean sharp properly set blades Never make a cut with a dull blade 9 To avoid pinching the blade support the workpiece properly before beginning a cut 6 When making a cut use steady even pressure Never force a cut 7 Do not cut wet or warped lumber 8 Always hold your workpiece firmly with both hands or use push blocks push sticks and feather boards to keep your body in a balanced position to be able to resist kickback should it occur 9 Use the right type of blade for the cut being made Making longitudinal cuts IMPORTANT After each new adjustment it is advisable to carry out a trial cut in order to check the set dimensions After switching on the saw wait for the blade to reach its maximum speed of rotation before commencing with the cut Take extra care when starting the cut 1 Longitudinal cuts involve cutting through a workpiece along its full length 2 One edge of the workpiece is pressed against the rip fence while its flat side rests on the table top 3 The saw blade guard must always be operational and cover the workpiece 4 When making longitudinal cuts you must always stand to one side of the cutting line 5 Set the fence to suit the required width 6 Switch on the table saw 7 With your fingers together place your hands flat on the workpiece and push the workpiece alo
21. th a minimum 10A circuit Never use the cord for any purpose other than that for which it is intended Adopt a firm standing position and keep your balance at all times Check the tool for signs of damage Before you use the tool it is imperative to check that its safety devices and any slightly damaged parts are working properly and in the way intended Check that the moving parts work properly and do not jam or whether any of the parts are damaged All parts must be fitted correctly and satisfy all conditions for the tool to work properly Unless otherwise stated in these instructions damaged safety devices and parts must be repaired or replaced by an authorised service facility Have damaged switches replaced by an authorised service facility This tool complies with the pertinent safety regulations Repairs are to be carried out only by qualified electricians at authorised service centres using original replacement parts The user may suffer an accident If this condition is not observed Rebating or grooving should not be carried out unless suitable guarding such as a tunnel guard is fitted above the table saw Saws shall not be used for slotting stopped groove Wear goggles Wear earmuffs Wear a breathing mask Unpacking Due to modern mass production techniques it is unlikely that your GMC Power Tool is faulty or that a part is missing If you find anything wrong do not operate the tool until the parts
22. truction Manual before using your new GMC Power Tool Take special care to heed the Cautions and Warnings Your GMC power tool has many features that will make your job faster and easier Safety performance and dependability have been given top priority in the development of this tool making it easy to maintain and operate Environmental protection Recycle unwanted materials instead Qa of disposing of them as waste All tools hoses and packaging should be sorted taken to the local recycling centre and disposed of in an environmentally safe way Description of symbols The rating plate on your tool may show symbols These represent important information about the product or instructions on its use Wear hearing protection Wear eye protection Wear breathing protection Conforms to relevant standards Nago Tor electromagnetic compatibility Specifications Voltage 230 240Vac 50Hz Input power 1800W No load speed 4500 min Blade diameter 250mm Blade bore size 16mm Blade teeth 40 Bevel range 0 to 45 Table size 610mm x 470mm Table height 900mm Depth of cut at 90 80mm Depth of cut at 45 55mm General safety instructions To use this tool properly you must observe the safety regulations the assembly instructions and the operating instructions to be found in this Manual All persons who use and service the machine have to be acquainted with this Manual and must be informed about its p
23. tting do not use the rip fence as a length stop as the cut off piece could bind between the fence and the blade and cause kickback 1 Push the mitre gauge into one of the two slots of the table saw and set it to the required angle If you also want to set the saw blade at an angle use the slot which prevents your hand and the mitre gauge coming into contact with the saw blade 2 Press the workpiece firmly against the mitre gauge 3 Switch on the saw 4 Push the mitre gauge and the workpiece toward the saw blade in order to make the cut IMPORTANT Always hold the guided part of the workpiece Never hold that part of the workpiece which is being cut off Always push the mitre gauge far enough forward for the workpiece to be cut through completely 5 Switch off the saw 6 Wait for the saw blade to stop before removing the off cuts Changing the saw blade WARNING Switch off the table saw and remove the mains power plug before carrying out any adjustments maintenance work or blade changes Wear work gloves when handling or fitting the blade 1 Loosen the height adjustment locking knob and turn the height adjustment handle until the saw blade is at its maximum height 2 Remove the blade guard assembly Fig d 3 Loosen and remove the screws securing the table insert 4 Take out the table insert 5 Remove the riving knife assembly Fig e 6 Use the spanner supplied to lock the spindle in position Fig
Download Pdf Manuals
Related Search