GE NetworX NX-7002 User's Manual
Contents
1. NX 7002 Installation manual Page 27 09 02 05 EA DESCRIPTION DEFAULT PROGRAMMING DATA EVENT SELECTION FOR REPORT CONTROL 4 BY PARTITION Segment 1 Alarms and Restores 0 0 0 0 0 0 0 0 Po Segmenta Open close 00000000 semets euos 09999900 Segmenta zonetroube oooooooo 1 Segment 5 Power Trouble AC Failure Low Batt 0 0 0 0 0 0 0 0 Segment Testrepors 99000000 _ segmente Downoad 00000000 Segmento Tempestonesondbos 999909090 segmentit seis 99900000 Segmeniz Sensortow Bate 99000000 _ segmentis Expander Trouble incl keypad 99909000 Segment 14 Failure To Communicate 0 0 0 0 0 0 0 0 Segmentis one Montoro 0 0 0 0 0 000 segmenti Reserved 19000000 DESTINATION SELECTION FOR REPORT CONTROLS 0 18 16 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 5 EEE I I EVENT SELECTION FOR REPORT CONTROL 5 BY PARTITION segment ond Restoes 00000000 segment 00000009 Segment zone tro 99000000 segments Power Trouble aC Falure Low Batt 00 00 9 00 0 Segment 6 Siren amp Telephone Fault 0 0 0 0 0 0 0 0 Segmente Program Downloads togal 09900093 Segmento Tomperslzones ondbod 00000000 Segment 11 Sensor Lost 0 0 0 0 0 0 0 0 segmentis Sensorto2. both guides 5 mw NX 7002 Installation manual Page 32 09 02 05 A Networ NX 7002 LAYOUT AND DESCRIPTION da T HEB L TO POS dil PSU ERROR REPORTING 0988 sou ee n DESCRIPTION Future use VVMIQ SIM card holder GPRS modem Connect antenna to this connector Header for software upgrade Connect to battery Connect main panel battery leads to these connectors Audio tap connector CON5 If the NX 7002 uses the voice channel for event reporting the special audio cable included needs to be stuffed between this connector of the NX 7002 and the Audio Tap connector of the control panel 9 Keypad bus terminals 10 Status LED s GSM in use ON when events are send over the voice or data channel Up download PSU error ON when the modem power source is to low Reporting ON when data is reported to the IP receiver or Mobile phone SMS GPRS active ON when the module is connected to the GPRS network and the first event is send It turns OFF when the module uses the voice channel SIM error ON when an incorrect PIN code is entered GSM com reserved Network OK reserved Bus com flashes when communicating on the Networx bus 11 Green LED ON when connected to TCP IP receiver HI e Nje NX 7002 Installation manual Page 33 09 02 05 Networ X TECHNICAL SPECIFICATIONS Technical
3. SMS Short Message Service SMS is a service for sending short text messages to mobile phones see locations 1 145 163 164 167 Transparent mode Data is transferred directly from one modem to another modem see location 0 segment 1 NX 7002 Installation manual Page 6 09 02 05 y Networ PROGRAMMING HE NX 7002 GPRS MODULE Programming the NX 7002 via the LED keypad ENTERING THE PROGRAM MODE To enter the program mode press 8 At this time the five function LED s Stay Chime Exit Bypass and Cancel will begin to flash Next enter the Go To Program Code factory default is 9 7 1 3 If the Go To Program Code is valid the Service LED will flash and the five function LED s will illuminate steady You are now in the program mode and ready to select the module to program Note It is impossible to enter program mode if any partition or the system is armed SELECTING THE MODULE TO PROGRAM Since all modules connected to the NetworX are programmed through the keypad the module you are programming should be the first entry To program the NX 7002 module enter 7 8 The 7 8 is the module number of the NX 7002 and the is the entry key PROGRAMMING A LOCATION Once the number of the module to be programmed has been entered the Armed LED will illuminate indicating it is waiting for a programming location to be entered Any location can be accessed by directly entering the de
4. This appendix provides a list of operator codes and the associated operator name Operator name Network name ID code On mobile phone Belgium Proximus Belgacom Mobile Proximus 20601 BEL PROXIMUS Mobistar Mobistar 20610 B Mobistar Base Base 20620 Base Denmark TDC Mobil A S TDC Mobil 23801 DK TDC Sonofon SONOFON 23802 SONO Hi3G Denmark ApS 3 DK 23806 3 DK Telia A S Denmark TELIA DK 23820 TELIA Orange A S Orange 23830 Orange France Orange France Orange F 20801 F FT SFR SFR 20810 SFR Bouygues Telecom Bouygues Telecom 20820 BOUYGTEL Germany T Mobile Deutschland GmbH DI 26201 TMO D Vodafone D2 GmbH Vodafone 26202 E Plus Mobilfunk GmbH E Plus 26203 E Plus 02 Germany GmbH amp Co OHG 02 Germany GmbH amp Co OHG 26207 02 de Italy Telecom Italia Mobile Telecom Italia Mobile 22201 TIM Vodafone Omnitel N V Vodafone 22210 voda IT Wind Telecomunicazioni SpA Wind Telecomunicazioni SpA 22288 I WIND H3G H3G 22299 3ITA Ireland Vodafone Ireland Plc Vodafone 27201 IRL Voda Eircell Eir Gsm 02 Communications Ireland Ltd 02 Communications Ireland Ltd 27202 O2 IRL METEOR METEOR 27203 METEOR Jersey Guernsey and Isle of Man Jersey Telecom JT GSM 23450 JT GSM Cable amp Wireless Guernsey Ltd Cable amp Wireless Guernsey 23455 C amp W Manx Telecom Pronto GSM 23458 Pronto Netherlands Vo
5. Orange NX 7002 Installation manual Page 38 09 02 05 www gesecurity com EMEA Distribution is a division of GE Security EMEA bvba COPYRIGHT 2005 GE Security EMEA bvba All rights reserved GE Security EMEA bvba grants the right to reprint this manual for internal use only GE Security EMEA bvba reserves the right to change information without notice
6. The delay in seconds before the NX 7002 GPRS module reports to report control 2 See location 3 EVENT SELECTION FOR REPORT CONTROL 2 BY PARTITION 16 segments feature selection data All events for report control 2 are disabled by default See location 4 DESTINATION SELECTION FOR REPORT CONTROL 3 1 segment This location contains the report destination for report control 3 See location 1 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 3 1 segment This location contains the backup report destination for report control 3 See location 2 REPORT DELAY FOR REPORT CONTROL 3 1 segment The delay in seconds before the NX 7002 GPRS module reports to report control 3 See location 3 Page 15 09 02 05 Networ LOCATION 12 LOCATION 13 LOCATION 14 LOCATION 15 LOCATION 16 LOCATION 17 LOCATION 18 LOCATION 19 LOCATION 20 LOCATION 21 LOCATION 22 LOCATION 23 NX 7002 Installation manual Nw EVENT SELECTION FOR REPORT CONTROL 3 BY PARTITION 16 segments feature selection data All events for report control 3 are disabled by default See location 4 DESTINATION SELECTION FOR REPORT CONTROL 4 1 segment This location contains the report destination for report control 4 See location 1 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 4 1 segment This location contains the backup report destination for report control 4 See location 2 REPORT DELAY FOR REPORT CONTROL 4 1 segment The delay in sec
7. receive signal transmissions There may be blind or non operational locations within the installation Normally these can be overcome by moving the antenna Note To test the signal strength at the intended location insert the SIM card into a mobile phone and check the strength indicator on the mobile phone MOUNTING THE NX 7002 Inside the can several 2 holed insertion points have been constructed This allows for either vertical or horizontal placement of the modules Notice that each insertion point has two sizes of holes a larger hole and a smaller hole Diagram 1 The black plastic PCB guides are grooved on one edge where the PC board will be seated The end with the half moon protrusion fits into the larger hole The smaller hole is for the screw Diagram 2 Place the first black plastic PCB guide in the top insertion point grooved edge downward The half moon Th protrusion will be in the large hole It does not require force siei Insert one of the provided screw into the smaller hole from de lt inside the can to secure it in place A screwdriver should reach T through the notch that runs the length of the guide to tighten O the screw The second PBC guide should be positioned opposite the first grooved edge up and placed in the lower insertion point using the same procedures described above Once mounted screw it in securely Diagram 3 The module should slide freely in the grooves of
8. specifications NX 7002 Power supply voltage 12Vdc Current consumption Nominal 30mA at 13 8Vdc Maximum up to 2 Amps peak Battery max 12V 7 2Ah Operating temperature 0 49 C Humidity Max 93 non condensating Dimensions PCB board only WxHxD 102 x97 x 24mm Weight PCB board only 115g NX 7002 Installation manual Page 34 09 02 05 Aietvwoo A N APPENDIX 1 REPORTING FIXED CODES IN CONTACT ID AND SIA The table below lists the event codes sent for the following reports if enabled when using Contact ID or SIA formats REPORT CONTACT ID SIA MANUAL TEST 601 RX AUTOTEST 602 RP OPEN User Number 401 OP CLOSE User Number 401 CL CANCEL User Number 406 OC DOWNLOAD COMPLETE 412 RS START PROGRAM 627 LB END PROGRAM 628 LX RECENT CLOSE User Number 401 CR EXIT ERROR User Number 457 EE EVENT LOG FULL 605 JL FAIL TO COMMUNICATE 354 RT EXPANDER TROUBLE device number 333 ET EXPANDER RESTORE device number 333 ER TELEPHONE FAULT 351 LT TELEPHONE RESTORE 351 LR SIREN TAMPER 321 YA SIREN RESTORE 321 YH AUX POWER OVERCURRENT device number 312 YP AUX POWER RESTORE device number 312 YQ LOW BATTERY device number 309 YT LOW BATTERY RESTORE device number 309 YR AC FAIL device number 301 AT AC RESTORE device number 301 AR BOX TAMPER device number 137 TA BOX TAMPER RESTORE dev
9. syntax gt eennn Rin leennn Rin For example gt 987654 BA001 Ri1 BAOO3 Ri1 YTOOO TA030 RI3 Syntax Description gt The message opening character A six digit account code ee A two digit SIA code nnn A three digit number e g Zone number Rin Area modifier is literal n is the area or partition number The message closing character Separator x X is optional X X is optional and may be repeated one or more times NX 7002 Installation manual Page 21 09 02 05 Networ LOCATION 165 LOCATION 166 LOCATION 167 LOCATION 168 LOCATION 169 LOCATION 170 LOCATION 171 LOCATION 172 LOCATION 173 SMS 2 PHONE NUMBER 20 segments See location 163 SMS 2 FORMAT 1 segment See location 164 Note By default not more than 20 SMS messages will be transmitted in a 24 hour time period If needed this number can be changed see location 162 segment 3 SMS SERVICE CENTRE NUMBER 20 segments This number is mandatory when SMS reporting is used Usually the SIM card automatically dials this number 14 indicates the end of the phone number Program 11 to insert in the phone number program 12 to insert it and program 13 to insert It is recommended to add the country prefix before the number For example 32 followed by the number UPLOAD DOWNLOAD PHONE NUMBER FOR CSD GSM 20 segments This number is mandato
10. the receiver Above 17 Perfect conditions Enter programming mode Press 78 to select the NX 7002 GPRS module Press 172 to select the Current GPRS RSSI location Note the RSSI reading and quit programming Testing the GSM and GPRS connection Enter programming mode Press 78 to select the NX 7002 GPRS module Press 174 to select the Device status flags location Check that the SIM card PIN is not blocked option 1 and option 2 should be ON Check that the SIM card is logged onto the GSM network option 3 should be ON Verify if the module is logged into the GPRS network option 7 should be ON Quit programming mode See NX 7002 layout and description for an overview of the different Status LED s on the NX 7002 NX 7002 Installation manual Page 12 09 02 05 Networ PROGRAMMING THE LOCATIONS LOCATION 0 MODULE MODE OF OPERATION FEATURE SELECTION 8 segments This location contains the system characteristics Segment 1 1 gt Enable site initiated downloading 98 from a keypad 2 Enable remote initiated downloading This setting enables the PC to dial into the NX 7002 It is dependent on other settings segment 5 5 and 6 3 Remoteinitiated download must be from known source If enabled program the phone number of the PC in location 168 4 Enable remote download at test time This setting configures the NX 7002 to automatically dial the PC to initiate an upload download session after an autotest You mu
11. 14 5 S 2 Phone number 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 5 5 service centre address phone number 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 I back phone number for CSD GSM 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 169 23 GSM SIM PIN code 10 10 10 10 10 10 10 10 170 23 GSM operator selection 0 0 0 0 0 A Current GSM operator read only name of operator 25 Gurent GSM ASSI read on asse x Current GPRS Bit Error Rate read onl NX 7002 Installation manual Page 30 09 02 05 DESCRIPTION DEFAULT PROGRAMMING DATA DEVICE STATUS FLAGS read only Segment 1 On Communication with GSM modem OK On SIM card PIN is OK On Logged in to the GSM network n Sending SMS n Connected to GPRS network n SIM card PUK code required t2 On Max reports in 24h limit reached 2 8 Reserved NX 7002 Installation manual Page 31 09 02 05 Networ INSTALLATION GUIDELINES e Avoid installing the module Where temperatures exceed 49 C or fall below 0 C Inthe immediate vicinity of electronic equipment n humid rooms The module is not hermetically sealed and excess moisture on the circuit board can eventually cause an electrical fault e the antenna within 2 m of the panel e Before permanently mounting the module test it at the intended location to ensure that the remote alarm receiver can
12. LOCATION 61 EVENT SELECTION FOR REPORT CONTROL 6 BY PARTITION 16 segments feature selection data All events for report control 6 are disabled by default See location 4 PRIMARY REPORTING FLAG FOR REPORT CONTROLS 1 segment The NX 7002 contains up to six report controls Turn on the relevant option to enable primary reporting for that report control Turn off the option to enable secondary reporting for that report control When secondary reporting is enabled the report control acts as a backup for the control panel Segment 1 1 gt Report Control 1 acts as Primary Reporting Off Report Control 1 acts as Secondary Reporting 2 On Report Control 2 acts as Primary Reporting Off Report Control 2 acts as Secondary Reporting 3 2 Report Control 3 acts as Primary Reporting Off Report Control 3 acts as Secondary Reporting 4 Report Control 4 acts as Primary Reporting Off Report Control 4 acts as Secondary Reporting 5 2 Report Control 5 acts as Primary Reporting Off Report Control 5 acts as Secondary Reporting 6 Report Control 6 acts as Primary Reporting Off Report Control 6 acts as Secondary Reporting 7 8 Reserved RESERVED PPP dial up account USER ID characters 1 16 16 segments Optional if using TCP IP reporting Contact the network provider to confirm if a PAP login is required and to obtain the user ID and password PPP dial up account USER ID characters 17 32 16 segments See lo
13. Networx Series NX 7002 GSM GPRS module Installation manual imagination at work Networ CONTENTS TONER REA RI RPM 3 GENERAL INFORMATION pe E H 4 ORDERING INFORMATION fT 4 FEATURE DEFINITIONS osito cose aene a eua rera Ce Eoo quos re Fa ee ue v ora se euo eo onus ve Fe ve va eoo su vp obseaususeeecheseesssvcsstucseosaeguasteeeeosassecssacceteecss 5 PROGRAMMING NX 7002 GPRS tta sa sesto tete ea sese see tese sese s esee tete se sese see eese eese season 7 PROGRAMMING THE NX 7002 VIA THE LED KEVPAD oet illa e bes 7 ENTERING THE PROGRAM MODE 8 cosh RR AA ta 7 SELECHNG THE MODULE TO XPROGRAM 5 Ra Ati des eE RR a 7 PROGRAMMING A LOCATION cccccccccccssssssscccsccsssssssccsscscssssssccescesssssssccsssccssssssecescsssssssccsssccsssssscsssssssssesssesssccsssessesescsesesesscessossesees 7 EXITING AL OGCATION E tet se ee i noi e io i ii e a eo ul o dii e 7 EXITING THE PROGRAM MODE EFIE EARN EE oR REE TR UV IINE 8 PROGRAMMING THE NX 7902 VIA THE LED KEYPAD Lelli n i Lala ene hi el 8 PROGRAMMING DATA tto an ii Oe vies A Rael oe a UM ca ae eee tas ia e latte 8 NUMERICAL CENSET E RI cry 8 FEATURE SELECTION DATA ta RE et Reach i pst RED I oa 9 START UP ENROLLING AND TESTING THE NX 7002 scccsccss
14. ROGRAMMING DATA MODE OF OPERATION FEATURE SELECTION Segment 2 Circle Numbers To Program Use SIA DCS as backup format Contact ID if off Reserved Reserved Reserved Reserved Reserved Reserved Reserved Segment 4 Circle Numbers To Program Reserved Reserved Reserved TCP IP Reporting in SIA Contact ID if off Reserved Reserved EH Reserved Reserved EVENT SELECTION FOR REPORT CONTROL 1 BY PARTITION Segment 1 Alarms and Restores 1 2 3 4 5 6 7 8 Segmente operos segments ess reseso semema 12345678 estrenos Segmente Program Download stes fd 234868 Segmento tompersizonesondbo 23456 segmenti resser segment 12 sensortowBatey 2846 segmentis Expander Trouble inc keypad 2356798 segmentis Zone Activity Monitoring 1234868 Sememis Reserved reser 15 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 2 NX 7002 Installation manual Page 26 09 02 05 DESCRIPTION DEFAULT PROGRAMMING DATA EVENT SELECTION FOR REPORT CONTROL 2 BY PARTITION Segment 1 Alarms and Restores 0 0 0 0 0 0 0 0 Po Segmenta Open close 1 99000000 semets 8g 00000000 Segmenta zcemuie Segment 5 Power Trouble AC Failure Low Batt 0 0 0 0 0 0 0 0 Segment Testrepors 99000000 _ s
15. S service centre address and under normal circumstances this should not be changed If you do need to change it include the international country prefix using a instead of leading zeros Program 13 to insert in the address NX 7002 Installation manual Page 10 09 02 05 Networ 0 Enrolling the SIM card on the GSM network e Insert the SIM card See Inserting the SIM for more information e Power up the NX 7002 GPRS module e Enter programming mode See Programming he NX 7002 GPRS module for more information Press 78 to select the module Press 169 to enter the GSM SIM PIN code location e Enter the first digit of the SIM PIN code Press to move to the next segment Continue in this way until all digits are programmed Press to save the changes and exit the location e Exit programming mode The SIM is automatically enrolled on the GMS network Note Each time you exit programming mode the modem restarts and reads the PIN number network operator and SMSC address number from the NX 7002 configuration Enrolling the SIM card on the GPRS network Enter programming mode Press 78 to select the module Press 169 to enter the GSM SIM PIN code location e Enter the first digit of the SIM PIN code Press to move to the next segment Continue in this way until all digits are programmed Press to save the changes and exit the location e Obtain an Access Point Number from the suppli
16. ance to the next segment of the location When you are in the last segment of a location and press the to enter the data you will exit that location This will now turn the Ready LED off and the Armed LED on As before you are now ready to enter another programming location NX 7002 Installation manual Page 9 09 02 05 Networ START UP ENROLLING AND TESTING THE NX 7002 Inserting the SIM card Note You must be free of all static electricity when handling electronic components e Always power down the system before inserting a SIM Card e Locate the SIM card holder on the board e the SIM card holder by sliding the metal clip as shown and lifting the holder e The SIM card holder opens e Slide the SIM card into the holder using the guides Make sure the contacts gold pads face the circuit board and the angled corners face out e Ensure the SIM card is inserted correctly in the holder and close the SIM card holder e Slide the metal clip back to the original position as shown e Power up the system Do not enter programming mode until the SIM card selects the network operator The SIM card automatically selects a network operator when enrolled on the network To manually select an operator enter the relevant network operator in location 170 See Appendix 2 Operator ID Codes for a list of operator ID codes Most SIM cards contain a pre programmed SM
17. cation 32 PPP dial up account PASSWORD 16 characters 16 segments See location 32 RESERVED NAME OF GPRS ACCESS POINT APN characters 1 16 16 segments This is a mandatory setting if using TCP IP reporting Contact the network provider to obtain the GPRS access point name NAME OF GPRS ACCESS POINT APN characters 17 32 16 segments See location 60 NX 7002 Installation manual Page 17 09 02 05 Networ LOCATION 62 LOCATION 63 LOCATION 64 LOCATION 100 LOCATION 101 LOCATION 102 LOCATION 103 LOCATION 104 LOCATION 118 LOCATION 119 LOCATION 120 LOCATION 138 LOCATION 139 LOCATION 140 LOCATION 141 LOCATION 142 LOCATION 143 NX 7002 Installation manual NAME OF GPRS ACCESS POINT APN characters 33 48 16 segments See location 60 NAME OF GPRS ACCESS POINT APN characters 49 64 16 segments See location 60 RESERVED DHCP ASSIGNED IP ADDRESS 4 segments When the NX 7002 logs into the GPRS network it is automatically assigned to an IP address This location is a read only location IP ADDRESS FOR TCP IP RECEIVER 1 4 segments If using TCP IP reporting enter in this location the IP address of the receiver 1 IP ADDRESS FOR TCP IP RECEIVER 2 4 segments If using TCP IP reporting enter in this location the IP address of the receiver 2 RESERVED RECEIVER ALARM AND POLL PORT 4 segments The number of the TCP IP port to which polling and alarms are repo
18. dafone Libertel N V Vodafone 20404 voda NL KPN Mobile The Netherlands BV KPN Mobile The Netherlands BV 20408 NL PTT NL KPN TELFORT B V TELFORT B V 20412 NL Tlfrt T Mobile Netherlands T Mobile NL 20416 TMO NL Orange Nederland N V Orange Nederland N V 20420 Orange Norway Telenor Mobil TELENOR 24201 TELENOR NETCOM AS NetCom 24202 COM Poland Polkomtel S A PLUS GSM 26001 PL PLUS Polska Telefonia Cyfrowa Era 26002 Era PTK Centertel IDEA 26003 DEA PL IDEA or PL 03 Portugal Vodafone Portugal Vodafone 26801 voda P Optimus Telecomunicacoes S A OPTIMUS 26803 P OPTIMUS OPTIMUS Telecomunicacoes Moveis Nacionais S A TMN 26806 P TMN P TELEMOVEL NX 7002 Installation manual Page 37 09 02 05 Networ Operator name Network name ID code On mobile phone Spain Vodafone Espana S A Vodafone 21401 E VODAF Retevision Movil S A AMENA 21403 RET MOV E 03 AMENA Telefonica Moviles Espana S A MOVISTAR 21407 MSTAR Sweden TeliaSonera Mobile TELIA MOBILE 24001 TELIA HI3G Access AB 3 24002 3 Tele 2 AB COMVIQ 24007 IQ Vodafone Sverige AB Vodafone 24008 voda SE Swefour AB Swefour AB 24010 Spring United Kingdom O2 UK Limited 02 23410 02 UK Vodafone Ltd Vodafone 23415 Voda Hutchison 3G UK Ltd 3 23420 3 UK T Mobile UK Limited T Mobile UK 23430 TMO UK T Mobile UK Limited T Mobile UK 23431 TMO UK T Mobile UK Limited T Mobile UK 23432 TMO UK Orange PCS Ltd Orange 23433
19. egmente Downoad 00000000 Segmento Tempestonesondbos 999909090 segmentit seis 99900000 Segmeniz Sensortow Bate 99000000 _ segmentis Expander Trouble incl keypad 99909000 Segment 14 Failure To Communicate 0 0 0 0 0 0 0 0 Segmenis one Monitoring 0 0 0 0 0 000 segmenti6 Reserved 10909000000 9 16 DESTINATIONSELECTIONFORREPORTCONTROL3 0 10 16 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 3 epost onc Fom pon I I EVENT SELECTION FOR REPORT CONTROL 3 BY PARTITION segmenti Wemsedfesoes ocoooooo __ segment 00000009 Segment zone tro 99000000 segments Power Trouble aC Falure Low Batt 00 00 9 00 0 Segment 6 Siren amp Telephone Fault 0 0 0 0 0 0 0 0 Segmente Program Downloads togal 09900093 Segmento Tomperslzones ondbod 00000000 Segment 11 Sensor Lost 0 0 0 0 0 0 0 0 segmentis Sensortow Sstey oooooooo Segment 13 Expander Trouble incl keypad 0 0 0 0 0 0 0 0 Failure To Communicate 0 0 0 0 0 0 0 0 Po segmentis Zone Activity Monitoring 99990000 Segment16 00000000 _ ae DESTINATION SELECTIONFORREPORTCONTROL4 I 0 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 4
20. er Press 60 to enter the Name of GPRS access point APN location Enter the first digit of the APN Press to move to the next segment Continue in this way until all digits are programmed Press to save the changes and exit the location e Optional You may need to enter the PPP password and PPP User ID required by the network To do this press 32 to select the PPP dial up account user ID location and program the password Then press 34 to select the PPP dial up account password location and program the user ID e Exit programming mode The SIM PIN is automatically enrolled on the GSM network NX 7002 Installation manual Page 11 09 02 05 y Networ Testing the RSSI value During the enrolling procedure it is mandatory to check the RSSI value signal strength of the NX 7002 GPRS module and record it in the system documentation The RSSI value is linked to the signal level of the GSM network and ranges from 0 31 with 99 as unknown The RSSI value may change due to environmental circumstances for example additional furniture or metal constructions If an RSSI reading is not satisfactory move the antenna to get a better reception VALUE DESCRIPTION Between 1 and 4 The module will not work properly and must be moved to another location Between 5 and 9 The module will work but ideally should be moved to another location Between 10 and 16 These are normal working values for the module located at a longer distance from
21. ice number 137 TR KEYPAD TAMPER 137 TA KEYPAD PANIC audible 120 PA KEYPAD PANIC silent 121 HA DURESS 121 HA KEYPAD AUXILIARY 1 110 FA KEYPAD AUXILIARY 2 100 MA RF SENSOR LOST zone number 381 SENSOR RESTORE zone number 381 R SENSOR LOW BATTERY zone number 384 XT SENSOR BATTERY RESTORE zone number 384 XR ZONE TROUBLE zone number 380 T ZONE TROUBLE RESTORE zone number 380 R ZONE TAMPER zone number 137 TA ZONE TAMPER RESTORE zone number 137 TR ZONE BYPASS zone number 570 B BYPASS RESTORE zone number 570 0 EARLY OPEN LATE CLOSE 451 OK NX 7002 Installation manual Page 35 09 02 05 A Networ 10 SIA FAIL TO CLOSE 454 CI ZONE ACTIVITY FAULT 391 NA ZONE ACTIVITY RESTORE 391 NS RF JAMMING 344 XQ RF JAMMING RESTORE 344 XH SMOKE DETECTOR CLEAN ME 393 YX SMOKE DETECTOR CLEAN ME RESTORE 393 YZ THE NUMBER IN PARENTHESES FOLLOWING THE EVENT IS THE NUMBER THAT WILL BE REPORTED AS THE ZONE NUMBER IF THERE ARE NO PARENTHESES THE ZONE WILL BE O The character transmitted in this slot will be the first character from the event code of the zone that is bypassed or in trouble SPECIAL REPORTS CONTACT ID SIA FAIL TO COMMUNICATE TCP IP or SMS 354 RTOO2 GSM network failure RSSI value to low 354 RTO78 NX 7002 Installation manual Page 36 09 02 05 Netwo APPENDIX 2 OPERATOR ID CODES
22. ion 1 is reported Use when a different account code for each partition is required When there is also an account code set for each report destination see location 139 142 145 146 the partition account code takes precedence ACCOUNT NUMBER FOR PARTITION 2 8 segments See location 154 ACCOUNT NUMBER FOR PARTITION 3 8 segments See location 154 ACCOUNT NUMBER FOR PARTITION 4 8 segments See location 154 ACCOUNT NUMBER FOR PARTITION 5 8 segments See location 154 ACCOUNT NUMBER FOR PARTITION 6 8 segments See location 154 ACCOUNT NUMBER FOR PARTITION 7 8 segments See location 154 ACCOUNT NUMBER FOR PARTITION 8 8 segments See location 154 NX 7002 Installation manual Page 19 09 02 05 Networ 0 LOCATION 162 TIMERS AND COUNTERS 16 segments numerical data Location 162 contains the duration of various system timing functions Segment 1 Segment 2 Segment 3 Segment 4 Segment 5 Segment 6 Segment 7 Segment 8 Segment 9 Segment 10 Segment 11 Segment 12 Segment 13 Segment 14 Max Number of network attempts The number of report attempts the NX 7002 GPRS module makes to send a report This can be from 0 to 15 Report attempts for FTC The number of attempts that can be made to a specific report destination before the Fail to Communicate condition is set This can be from 1 to 15 Maximum reports in 24 hours The NX 7002 GPRS module stops reporting messages when the number of message
23. l at acceptable level GSM MODEM MANUFACTURER READ ONLY 16 segments This location displays the manufacturer of the GSM GPRS modem used on the NX 7002 GSM MODEM MODEL READ ONLY 16 segments This location displays the model of GSM GPRS modem used on the NX 7002 GSM MODEM SOFTWARE REVISION READ ONLY 16 segments This location displays the software revision of the GSM GPRS modem used on the NX 7002 GSM MODEM SERIAL NUMBER READ ONLY 16 segments This location displays the serial number of the GSM GPRS modem used on the NX 7002 RESERVED NX 7002 Installation manual Page 23 09 02 05 A Networ NX 7002 FOR PRIMARY OR BACKUP REPORTING NX 7002 for primary reporting The NX 7002 can be configured to be the primary transmitter In this case the NX 7002 acts as the main alarm reporting device If the NX 7002 fails for example if there is no GSM coverage or there is jamming if the network of the provider is down or there are technical problems on the receiver side another device the onboard dialler of the panel or an auxiliary dialler can be configured to act as backup In this case set location 2 to 255 Other dialler as backup for the NX 7002 If another dialler is used as the backup device e Enable the Autotest report options in that dialler e Ensure that the reporting format used in the backup device is the same as the reporting format used in the NX 7002 If the NX 7002 fails to report over
24. lation manual Page 24 09 02 05 Networ The NX 7002 can be configured as the backup device of an auxiliary dialler NX 590 TCP IP module or NX 570 ISDN module e Select the desired report control in location 1 e Enable the Autotest report options e Ensure that the reporting format used with the auxiliary dialler is the same as the reporting format used in the NX 7002 NX 7002 Installation manual Page 25 09 02 05 Networ NX 7002 PROGRAMMING WORKSHEETS Factory defaults are in bold italic text DESCRIPTION Segment 1 Circle Numbers To Program Enable site initiated downloading 98 from a keypad Enable remote initiated downloading Remote initiated download must be from known source E Enable auto answer incoming CSD GSM download call nable remote download at test time Callback required for incoming CSD GSM download call Use V 110 for site initiated CSD GSM calls Use non transparent mode for site initiated CSD GSM calls Segment 3 Circle Numbers To Program 298 13 1 1 2 eserved olling enable for UL AA eserved R Reserved R R Reserved DESTINATION SELECTION FOR REPORT CONTROL 1 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 1 REPORT DELAY FOR REPORT CONTROL 1 eserved eserved eserved 4 4 1 14 DESTINATION SELECTION FORREPORTCONTROLT ENEENE VH 3 14 REPORTDELAYFORREPORTCONTROL o_O DEFAULT P
25. mail reporting not yet available This location contains the report destination for report control 1 Select from the table below Email 1 Email Reporting to Email Account 1 not yet available Email 2 Email Reporting to Email Account 2 not yet available SMS 1 SMS Reporting to Mobile Phone 1 SMS 2 SMS Reporting to Mobile Phone 2 LOCATION 2 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 1 1 segment If the primary destination selection location 1 fails a backup destination can be selected If using another device as the backup destination for example panel dialler set the reporting format SIA or CID in location 0 segment 2 option 1 and enable test report events for the backup device This location contains the backup report destination for report control 1 Select from the table below Email 1 Backup Email Reporting to Email Account 1 not yet available Backup Email Reporting to Email Account 2 not yet available Backup SMS Reporting to Mobile Phone 2 The NX 7002 is not used as backup Instead another dialler is used for example panel dialler LOCATION 3 REPORT DELAY FOR REPORT CONTROL 1 1 segment The delay in seconds before the NX 7002 GPRS module reports If any other events occur during this delay they are sent with the first event in one message if using SMS reporting This does not apply if using TCP IP reporting it does not support multiple events in one message This can be from 0 to 255 sec
26. nt during this time the report control reports the event This can be from 1 to 255 seconds If set to 0 the setting is disabled Reserved LOCATION 163 SMS 1 PHONE NUMBER 20 segments The phone number to which SMS reports are sent This phone number is independent from the phone numbers programmed in the control panel 14 indicates the end of the phone number Program 11 to insert in the phone number program 12 to insert and a n program 13 to insert It is recommended to add the country prefix before the number For example 32 followed by the phone number NX 7002 Installation manual Page 20 09 02 05 Networ LOCATION 164 SMS 1 FORMAT 1 segment The communicator format used to transmit to the SMS 1 report destination from the NX 7002 GPRS module Consult the instructions for your central station receiver to determine which format is compatible SIA reporting over SMS can be set to one of three modes DATA FORMAT 0 SIA Separate Events SIA Combined Events SIA with Area Modifier If 0 Separate Events is selected messages are sent using the syntax gt eennn eennn For example 123456 BA001 If 1 Combined Events is selected messages are sent using the syntax gt eennn eennn aaaaaa eennn eennn For example 3123456 BA001 987654 YT000 345678 TA030 If 2 Area Modifier is selected messages are sent using the
27. ogged into the network RSSI values range from 0 to 31 with 99 as unknown See Testing the RSSI value for more information CURRENT GPRS BIT ERROR RATE READ ONLY 1 segment This location will show the BER Bit Error Rate value in The BER value is periodically updated when logged into the network BER values range from 0 to 7 with 99 as unknown NX 7002 Installation manual Page 22 09 02 05 Networ LOCATION 174 LOCATION 175 LOCATION 176 LOCATION 177 LOCATION 178 LOCATION 179 LOCATION 215 DEVICE STATUS FLAGS 2 segments This location contains specific status information of the GSM GPRS module If the option is the status condition is true Segment1 1 On 2 3 On 4 On On 6 On On On Segment2 1 On Communication with GSM modem OK SIM card PIN is OK Logged in to the GSM network Sending SMS Using GSM audio connection Using GSM CSD connection Connected to GPRS network SIM card PUK code required Battery voltage failure The NX 7002 measures and monitors battery voltage It shares a battery with the contro panel 2 On GSM PSU voltage failure The main battery creates a 3 8 V power supply for the GPRS modem 3 On Bus voltage failure The bus supplies a 13 8 V voltage to the NK 7002 On On On 7 On On Communication channel failure Up download session in progress Up download session starting Reporting in Progress RSSI leve
28. on If an attempt is Made to program a number too large for a particular segment the keypad sounder will emit a triple beep indicating an error and remain in that segment awaiting a valid entry Remark The number in the location will be displayed on the LCD keypad For locations with a maximum of 15 the hexadecimal equivalent will be displayed in parenthesis Example 11 B or 14 E FEATURE SELECTION DATA Feature selection data will display the current condition on or off of eight features associated with the programming location and segment selected Pressing a button on the keypad 1 through 8 that corresponds to the feature number within a segment will toggle on off that feature Pressing any numeric key between 1 and 8 for selection of a feature will make the corresponding LED illuminate feature ON Press the number again and the LED will extinguish feature OFF You will see that numerous features can be selected from within one segment For instance if all eight features of a segment are desired pressing 1 2 3 4 5 6 7 8 will turn on LED s 1 through 8 as you press the keys indicating that those features are enabled LCD keypad users note The numbers of the enabled features will be displayed However the features not enabled will display a hyphen After the desired setting of features is selected for this segment press the key This will enter the data and automatically adv
29. onds NX 7002 Installation manual Page 14 09 02 05 Networ LOCATION 4 LOCATION 5 LOCATION 6 LOCATION 7 LOCATION 8 LOCATION 9 LOCATION 10 LOCATION 11 NX 7002 Installation manual EVENT SELECTION FOR REPORT CONTROL 1 BY PARTITION 16 segments feature selection data All events for report control 1 are enabled by default Select the partition s to include in the event report Enabled events are formatted into one or more messages according to pre configured settings and sent to the selected report destination Enable the Test Reports event group if using the NX 7002 as backup to another auxiliary dialler Segment 1 Alarms and Restores Segment 2 Open Close Segment 3 Bypass Segment 4 Zone trouble Segment 5 Power trouble AC failure and Low Battery Segment 6 Siren amp Line Fault Segment 7 Test Report Segment 8 Program Download amp Log full Segment 9 Tamper Segment 10 Short Circuit Segment 11 Sensor Lost Segment 12 Sensor Low Battery Segment 13 Expander Trouble Segment 14 Fail To Communicate Segment 15 Zone Activity Monitoring Segment 16 Reserved DESTINATION SELECTION FOR REPORT CONTROL 2 1 segment This location contains the report destination for report control 2 See location 1 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 2 1 segment This location contains the backup report destination for report control 2 See location 2 REPORT DELAY FOR REPORT CONTROL 2 1 segment
30. onds before the NX 7002 GPRS module reports to report control 4 See location 3 EVENT SELECTION FOR REPORT CONTROL 4 BY PARTITION 16 segments feature selection data All events for report control 4 are disabled by default See location 4 DESTINATION SELECTION FOR REPORT CONTROL 5 1 segment This location contains the report destination for report control 5 See location 1 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 5 1 segment This location contains the backup report destination for report control 5 See location 2 REPORT DELAY FOR REPORT CONTROL 5 1 segment The delay in seconds before the NX 7002 GPRS module reports to report control 5 See location 3 EVENT SELECTION FOR REPORT CONTROL 5 BY PARTITION 16 segments feature selection data All events for report control 5 are disabled by default See location 4 DESTINATION SELECTION FOR REPORT CONTROL 6 1 segment This location contains the report destination for report control 6 See location 1 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 6 1 segment This location contains the backup report destination for report control 6 See location 2 REPORT DELAY FOR REPORT CONTROL 6 1 segment The delay in seconds before the NX 7002 GPRS module reports to report control 6 See location 3 Page 16 09 02 05 Networ LOCATION 24 LOCATION 25 LOCATION 26 LOCATION 31 LOCATION 32 LOCATION 33 LOCATION 34 LOCATION 35 LOCATION 59 LOCATION 60
31. ounder will emit a triple error beep beep beep beep and remain in that segment awaiting a valid entry NX 7002 Installation manual Page 7 09 02 05 Networ EXITING THE PROGRAM MODE When all the desired changes in programming have been made it is time to exit the program mode Pressing the Exit key will exit this programming level and then return to the Select a Module to Program level If no additional modules are to be programmed pressing the Exit key again will exit the program mode If there is a module to be programmed it may be selected by entering its address followed by the key see Selecting the module to program for more information The procedure for programming these devices is the same as for the control panel except the locations will be for the module selected Note Each time you exit programming mode the modem restarts and reads the PIN number network operator and SMSC address number from the NX 7002 configuration Programming the NX 7002 via the LCD keypad All steps required for programming are the same as the aforementioned LED keypad The LCD keypad display will prompt you for the data required While in the programming mode and not in a location the number in parenthesis is the location you were previously changing For example if the display reads Enter location then 5 it is reminding you that location 5 was the last location you programmed Refer also to Programming Data
32. perator The network operator for the SIM card Polling Polling is the process by which the system reports periodically to a receiver to say it is still alive It works in conjunction with TCP IP reporting only Polling is more frequent than a daily test call but less frequent than continuous monitoring If you configure a very short polling time polling occurs very frequently and can generate large quantities of data When setting the polling time you should consider the speed of the GPRS network and the cost of data transmission see location 0 segment 3 and location 162 segment 6 PUK code Personal Unblocking Key The code to use to unblock the SIM card The SIM card can block when an incorrect SIM PIN is entered repeatedly Report control A block of reporting data that contains configurations to format selected events into one or more messages according to pre configured settings and send them to specified destinations see location 1 RSSI Received Signal Strength Indicator This indicates the field signal strength of the NX 7002 see location 172 and location 162 segment 11 and 12 Secondary reporting The means of reporting events that the control panel fails to report When secondary reporting is enabled the report control set in the NX 7002 will act as a backup for the control panel see location 25 and location 162 segment 3 NX 7002 Installation manual Page 5 09 02 05 Networ SIM card PUK code See PUK code
33. rt us o _ 1 Recever nume 0001 HWePiunemme T_ ee _ 19 CP P2Account number 999941090 e i N 25 17 PRIMARY REPORTING FLAGS FOR REPORT CONTROL 1 TO 6 Segment 1 Circle Numbers To Program 1 On Report Control 1 is Primary Reporting Flag Off Report Control 1 is Backup for control panel 20 SMS 2 Account number D 147 153 20 RESERVE NX 7002 Installation manual Page 29 09 02 05 oc G DESCRIPTION DEFAULT PROGRAMMING DATA 59 20 Segment 6 5 157 20 Accountrumberporition 99992 0900 __ Account numberporttions___________ _ 09009000 1 Account number partition 6 0 0 0 0 0 0 0 0 160 20 Account number partition 7 0 0 0 0 0 0 0 0 e Cdl 161 20 Accountnumberpariton 99000090 __ 162 21 TERS TIMERS AND COUN Max Number of network attempts Report attempts for Fail To Communicate Il Maximum reports in 24 hours Time in seconds for overall network attempt Reserved TCP IP Polling time in minutes for PPP connections Reserved Reserved Reserved Baud rate for CSD GSM download GSM line fault RSSI threshold GSM line fault time in seconds Control reporting timeout in seconds for secondary reporting 180 Reserved S 1 Phone number 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14 14
34. rted The default port is 9999 and under normal circumstances should not be changed RESERVED TCP IP 1 ACCOUNT NUMBER 8 segments The SIA or Contact ID account number used for reporting towards the TCP IP receiver SIA account numbers are 6 digits long Contact ID account numbers are 4 digits long Add leading zeros to create an 8 digit number TCP IP 1 RECEIVER NUMBER 4 segments The phone line receiver number associated with the TCP IP 1 account TCP IP 1 LINE NUMBER 4 segments The line number associated with the TCP IP 1 account Enter the account number and destination number for the receiver TCP IP 2 ACCOUNT NUMBER 8 segments See location 139 TCP IP 2 RECEIVER NUMBER 4 segments See location 140 Page 18 09 02 05 Networ 0 LOCATION 144 LOCATION 145 LOCATION 146 LOCATION 147 LOCATION 153 LOCATION 154 LOCATION 155 LOCATION 156 LOCATION 157 LOCATION 158 LOCATION 159 LOCATION 160 LOCATION 161 TCP IP 2 LINE NUMBER 4 segments See location 141 SMS 1 ACCOUNT NUMBER 8 segments The SIA account number used for SMS reporting SIA account numbers are 6 digits long Enter the first digit of the SIM PIN code in segment 3 segment 1 and 2 are not used Press to move to the next segment Continue in this way until all digits are programmed SMS 2 ACCOUNT NUMBER 8 segments See location 145 RESERVED ACCOUNT NUMBER FOR PARTITION 1 8 segments The account code sent when partit
35. ry if up downloading via the NX 7002 is required using the call back feature An Up download call will use the data channel Contact your network provider to make sure your SIM card supports the data channel Program the call back number in this location 14 indicates the end of the phone number Program 11 to insert in the phone number program 12 to insert and program 13 aon to insert GSM SIM PIN CODE 8 segments Enter the SIM pin code in this location A 10 indicates the end of the code GSM OPERATOR SELECTION 6 segments The network operator ID code Set this to 00000 to allow the SIM card automatically select a network operator Alternatively enter an operator ID code in this location to manually select a network operator If using a 5 digit code enter A or 10 after the code Appendix 2 lists all network operators and ID codes An invalid selection or unreachable network will prevent location 174 segment 3 turning on CURRENT GSM OPERATOR READ ONLY 1 segment This location will show the name of the automatically or manually selected GSM network operator This location is read only and only valid when the NX 7002 is logged into the GSM network See Appendix 2 Operator ID Codes for a detailed list of operators CURRENT GSM RSSI READ ONLY 1 segment This location will show the RSSI Received Signal Strength Indicator value The RSSI value is periodically updated when l
36. s in a 24 hour time frame exceeds this number This can be from 1 to 255 If set to 0 there is no limitation Time in seconds for overall network attempt The maximum length of time for each attempt by the NX 7002 to report to each receiver If the report is not successful during this time the attempt is abandoned This can be from 0 to 255 seconds Reserved TCP IP Polling time in minutes This setting must match the TCP IP polling time set on a TCP IP receiver The setting on the TCP IP receiver is determined by the speed of the GPRS network and cost of data transmission This can be from 1 to 255 If set to 0 the setting is disabled Reserved Reserved Reserved Baud rate for CSD GSM download This setting must match the baud rate set on the PC modem 42 2400 Baud 5 4800 Baud 629600 Baud GSM line fault RSSI threshold The acceptable level of the RSSI signal If the signal falls below this level for the amount of time set in segment 12 a line fault is generated This can be from 1 to 31 If set to O the setting is disabled GSM line fault time The length of time the RSSI signal must be below the RSSI threshold before a line fault is generated This can be from 0 to 255 seconds Control reporting timeout for secondary reporting The maximum time during which the control panel must report an event If the NK 7002 report control SMS or TCP IP report control is set for secondary reporting and the control panel does not report the eve
37. sired programming location followed by the pound key If the location entered is a valid location the Armed LED will extinguish the Ready LED will illuminate and the zone LED s will show the binary data for the first segment of this location While entering new data the Ready LED will begin flashing to indicate a data change in process The flashing will continue until the new data is stored by pressing the key Upon pressing the key the keypad will advance to the next segment and display its data This procedure is repeated until the last segment is reached Pressing the key will exit from this location and the Armed LED will illuminate again waiting for a new programming location to be entered If the desired location is the next sequential location press the Police key If the previous location is desired press the Fire key If the same location is desired press the Medic key To review the data in a location repeat the above procedure pressing the key without any numeric data entry Each time the key is pressed the programming data of the next segment will be displayed for review EXITING A LOCATION After the last segment of a location is programmed pressing the key will exit that location turn the Ready LED off and the Armed LED on As before you are now ready to enter another programming location If an attempt is made to program an invalid entry for a particular segment the keypad s
38. sssssiccsescsccsscicocceseecssescescsevcvestasessescecvcoeoussassescdavensevaceseescostesssesenes eesdeuaeeoagee 34 TECHNICAL cased ot eite es E 34 APPENDIX 1 REPORTING FIXED CODES IN CONTACT ID AND tasa ses sete oa 35 APPENDIX 2 OPERATOR ID CODES eee eei vos teenage e ucts arianna slancio o aav ed ve Pa 37 NX 7002 Installation manual Page 3 09 02 05 Networ X GENERAL INFORMATION The NX 7002 is the GPRS module that can be added to the Networx range of panels NX 8 EUR NX 6 EUR and NX 4 EUR The NX 7002 GPRS module features include e Wireless event reporting e Six programmable report destinations e Selectable reportable events from eight partitions e Compatible with PSTN or ISDN reporting PSTN ISDN as backup e SIA and Contact ID reporting over GPRS towards Osborne Hoffman OH2000 TPC IP receiver e reporting with optional area modifiers using SMS messages e The control panel can use GSM in addition to PSTN reporting all panel protocols using GSM e Wireless upload download using a GSM CSD connection e Upload download may be initiated remotely or locally e Optional download sessions during test calls The NX 7002 package contains NX 7002 GSM GPRS module 1 5m e
39. ssssssesscccccsssssceeccessssssscecececesesssscececescscscsscesecescssssssceneces 10 INSERTING THE SIMSGAR Di 4204 2 ae ei e it e AN ieri ei i ie a i al ae 10 ENROLLING THE SIM CARD ON THE GSM NETWORK cirie eee 11 ENROLLING THE SIM CARD ON THE GPRS NETWORK ieri 11 TESTING THE RSSIi VALUES e eot reo cci eerte rete t dedere cede eee eee cte te edere te ede 12 TESTING THE GSM ANB GPRS CONNECTION paolida ela bete eve EE EYE 12 PROGRAMMING THE LOCATIONS iius o ces ee o as vo do rena a oe uo oocesesscedesvascepesecsducnecescesetesssusecbesacsucessesecasssesesnesaecacdosassucsuesses 13 NX 7002 FOR PRIMARY OR BACKUP REPORTING esee eee ee een nenne sese see eese ease sese e e tete se ses s e a 24 NX 7002 FOR PRIMARY REPORTING cccccssesssssscsccsssessesscscceceessesssscescesssessssscsceesesssessesecscsesssesssssceceesseessssseeceeseeasessececenseenses 24 NX 200 2sFORIBACKUR REPORTING ete sese ree core eee ilaele 24 NX 7002 PROGRAMMING WORKSHEETS eee eee eee eren nene tete tasa sa sese e teta sa sese see t tetas ases e eese ense ses e e teta se aes s e eese aaa 26 INSTALLATION p 2A ccc 32 MOUNTING THE TAS LE 32 NX 7002 LAVOUT AND DESCRIPTION viccssccscssccessssccecssatsocesoestcccascacecesosees 33 TECHNICAL SPECIFICATIONS
40. st program the autotest in the control panel 5 2 Enable auto answer incoming CSD GSM download call If enabled the NX 7002 will automatically accept an incoming call If disabled the user needs to accept an incoming call 99 as soon as a ding dong is heard on the keypad 6 2 Callback required for incoming CSD GSM download call If enabled the NX 7002 will call back to the PC before starting an up download session 72 UseV 110 for site initiated CSD GSM calls Enable this setting if the PC is on an ISDN line and is using an ISDN modem 8 2 Use non transparent mode for site initiated CSD GSM calls If you are experiencing problems with upload download change this setting from transparent mode to non transparent mode or vice versa Segment 2 1 Use SIA DCS as backup format Contact ID if off This setting selects the reporting format when using another device as backup The same format must be set on the backup device 2 8 Reserved Segment 3 1 Reserved 2 Polling enable for TCP IP for UL AA If polling is enabled set the polling period in location 162 segment 6 3 8 Reserved Segment4 1 3 Reserved TCP IP reporting in SIA Contact ID if Off 5 8 Reserved Segment 5 8 Reserved NX 7002 Installation manual Page 13 09 02 05 Networ 0 LOCATION 1 DESTINATION SELECTION FOR REPORT CONTROL 1 1 segment The NX 7002 contains up to six report controls Each report control can be defined for SMS reporting TCP IP reporting or e
41. the GPRS network to the IP receiver you can use a second report control from the NX 7002 as backup For example use SMS reporting as the backup report control In this case set location 1 to 1 TCP IP1 and location 2 to 5 SMS1 NX 7002 for backup reporting The NX 7002 can be configured to transmit events only when the primary dialler control panel auxiliary dialler fails to do so In this case the NX 7002 acts as the backup reporting device The NX 7002 can be configured as the backup device of the control panel in two ways 1 Backup reporting using a report control TCP IP or SMS Select the desired report control in location 1 and set the corresponding report control as a secondary backup report control in location 25 2 Backup reporting using the GSM voice channel In this case the NX 7002 acts as a transparent backup device for the control panel No programming in the NX 7002 is required except for the SIM PIN code in location 169 All event reporting is programmed in the control panel The phone number must be programmed twice in the control panel e Program phone number 1 as usual For example 011234567 e Entera 10 in front of phone number 2 For example 10011234567 This forces the NX 7002 to dial the phone number instead of the control panel e The special audio cable included must be stuffed between the NX 7002 and the control panel See NX 7002 layout and description for more information NX 7002 Instal
42. w Sstey oooooooo Segment 13 Expander Trouble incl keypad 0 0 0 0 0 0 0 0 Failure To Communicate 0 0 0 0 0 0 0 0 Po segmentis Zone Activity Monitoring 99990000 Segment16 00000000 _ Lu DESTINATION SELECTION FOR REPORT CONTROL 6 0 0 BACKUP DESTINATION SELECTION FOR REPORT CONTROL 6 NX 7002 Installation manual Page 28 09 02 05 toc PG DESCRIPTION DEFAULT PROGRAMMING DATA 24 17 EVENT SELECTION FOR REPORT CONTROL 6 BY PARTITION Segment 1 Alarms and Restores 0 0 0 0 0 0 0 0 Po Segment2 00000000 Segments 09000000 S Segen zwemobe 0000000 1 Segment 5 Power Trouble AC Failure Low Batt 0 0 0 0 0 0 0 0 Segment 09999990 Segment Program Downoad logt 009009000 segments Tornpers zones andbox 090999090 segmenti sensortst 99900000 Segmentiz 099992990 Segment13 Expander Trouble nek keypad 0 0 0 00000 Segment 14 Failure To Communicate 0 0 0 0 0 0 0 0 Zone Activity Monitoring 69999900 segmenti Ruewd 00000000 On Report Control 3 is Primary Reporting Flag Off 2 Report Control 3 is Backup for control panel Reserved 34 16 PPP idiakup account pasword i Receiver alarm and poll po
43. which follows Programming data Programming data is always one of two types One type of data is numerical which can have values from 0 15 or 0 255 depending on the segment size The other type of data feature selection data is used to turn features on or off Use the following procedures with these two data types NUMERICAL DATA Numerical data is programmed by using the numeric keys of the system keypad to enter a number from 0 255 To view the data in a location a binary process is used With this process the LED s for zones 1 through 8 are utilized and the numeric equivalents of their illuminated LED s are added together to determine the data in a programming location The numeric equivalents of these LED s are as follows Zone 1LED 1 Zone 2 LED 2 Zone 3 LED 4 Zone 4LED 8 Zone 5 LED 16 Zone 6 LED 32 Zone 7 LED 64 Zone 8 LED 128 Example If the numerical data to be programmed in a location is 66 press 6 6 on the keypad The LED s for zone 2 and zone 7 will become illuminated indicating 66 is in that location 2 64 66 NX 7002 Installation manual Page 8 09 02 05 Networ Once the data is programmed press the key to enter the data and advance to the next segment of that location After the last segment of a location is programmed pressing the key will exit that location turn the Ready LED off and the Armed LED on As before you are now ready to enter another programming locati
44. xternal antenna e 2 black PCB guides for mounting Audio cable The GSM GPRS module requires a SIM card not included In order to obtain all NX 7002 features the SIM card needs to support Voice channel event reporting over the voice channel e Data channel up downloading e event reporting towards IP receiver over GPRS Contact your local network provider for more information ORDERING INFORMATION For detailed ordering information and part numbers please refer to the EMEA Distribution price list of the Caddx product range NX 7002 Installation manual Page 4 09 02 05 FEATURE DEFINITIONS CID Contact ID reporting protocol CSD Circuit Switched Data This is the communication used to upload download data It is similar to a modem but it is wireless and built in to the NX 7002 see locations 0 162 segment 10 and location 168 GPRS General Packet Radio Service A global standard for wireless communications with a maximum speed of 115 kilobits per second It supports a range of bandwidths and can transmit and receive both small bursts and large amounts of data GSM Global System for Mobile Communications A global standard for wireless communications with a maximum speed of 9 6 kilobits per second It supports narrowband Time Division Multiple Access TDMA Non transparent mode An intermediate modem is used on the network to transfer data from one modem to another see location 0 segment 1 O
Download Pdf Manuals
Related Search