Home

GE 239D4106P009 User's Manual

1. Space saving ice maker Ice maker and bin are located on the door creating more usable storage space 2 Showcase LED lighting LED lighting is positioned throughout the interior to spotlight areas in the refrigerator LEDs are located under the fresh food door to light the freezer when opened Drop down tray Allows for extra door storage when you need it and tucks away when you don t Full width temperature controlled drawer on some models Adjustable temperature control bin that can accommodate larger items Dairy bin Separate compartment for your items 6 Dual ice maker utility bin on some models An ice maker in both compartments gives you more ice whenever you need it or a utility bin designed for flexible storage Select Models Only 80 8 8 8 8 QuickSpace shelf Functions as a normal full sized shelf when needed and easily slides back to store tall items below Spillproof shelves Designed to capture your spills for easier clean up Removable condiment bin Separate bin designed for easy removal and storage Removable door bin Can be removed for those with a wall limiting the door opening Climate zone bin Separate bins for produce storage In the door filter Located in the door for more available space in the fresh food section and easy replacement Water
2. Outlet aah a A NOTE Commonwealth of Massachusetts PA aiag ae d Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted Washer in Massachusetts Consult with your licensed plumber Ferrule sleeve 8 FLUSH OUT THE TUBING Turn the main water supply on and flush out the tubing until the water is clear Shut the water off at the water valve after about one quart 1 liter or 2 minutes of water has been 6 ROUTE THE TUBING flushed through the tubing Route the tubing between the cold water line and the refrigerator Route the tubing through a hole drilled in the wall or floor behind the refrigerator or adjacent base cabinet as close to the wall as possible To complete the installation of the refrigerator go back to Step 11 in Installing the Refrigerator 36 Normal operating conditions GEAppliances com Newer refrigerators sound different from older refrigerators Modern refrigerators have more features and use newer technology Do you hear what I hear These sounds are normal HUMMM WHOOSH The new high efficiency compressor see run faster and longer than your old refrigerator and you may hear a high pitched hum or pulsating sound while it is operating You may hear a whooshing sound when the doors close This is due to pressure equalizing within the refrigerator After dispensing ice a motor will close the ice chute to keep warn room air from ente
3. or adjustable wrench e Straight and Phillips blade screwdriver eS e Two 1 4 outer diameter compression nuts and 2 ferrules sleeves to connect the copper tubing to the shutoff valve and the refrigerator water valve OR e If you are using a GE SmartConnect Refrigerator Tubing kit the necessary fittings are preassembled to the tubing e If your existing copper water line has a flared fitting at the end you will need an adapter available at plumbing supply stores to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting Do not cut formed end from GE SmartConnect Refrigerator tubing e Shutoff valve to connect to the cold water line The shutoff valve should have a water inlet with a minimum inside diameter of 5 32 at the point of connection to the COLD WATER LINE Saddle type shutoff valves are included in many water supply kits Before purchasing make sure a saddle type valve complies with your local plumbing codes LL SHUT OFF THE MAIN WATER SUPPLY Turn on the nearest faucet long enough to clear the line of water 2 CHOOSE THE VALVE LOCATION Choose a location for the valve that is easily accessible It is best to connect into the side of a vertical water pipe When it is necessary to connect into a horizontal water pipe make the connection to the top or side rather than at the bottom to avoid drawing off any
4. Water dispenser has not been used Dispense water until all water in system for along time is replenished Water in glass is warm Water dispenser does not work Water spurting from dispenser Newly installed filter cartridge Select Models Only Normal when refrigerator is first Wait 24 hours for the refrigerator to installed completely cool down Water dispenser has not been used Dispense water until all water in system for along time is replenished Water system has drained Allow several hours for replenished supply to chill Water supply line turned off or not See Installing the Water Line connected Water filter clogged or filter bypass Replace filter cartridge or remove filter plug not installed and install bypass plug Air may be trapped in the water Press the dispenser arm for at least 5 system minutes Water in reservoir is frozen because the controls are set too cold 38 Set the refrigerator control to a warmer setting and wait 24 hours If the water does not dispense after 24 hours call for service Run water from the dispenser for 5 minutes about 2 gallons Before you call for service GEAppliances com O Troubleshooting Tips cont Problem Possible Causes What to Do No water or ice cube production Supply line or shutoff valve is clogge Call a plumber Water filter is clogged Replace filter cartridge or remove filter and install bypass plug Filter cartridge not properly installed Remove an
5. selected CUBED ICE This happens occasionally when a few cubes accidentally get directed to the crusher After crushed ice is dispensed some water may drip from the chute Sometimes a small mound of snow will form on the door in the ice chute This condition is normal and usually occurs when you have dispensed crushed ice repeatedly The snow will eventually evaporate If no water is dispensed when the refrigerator is first installed there may be air in the water line system Press the dispenser button for at least 5 minutes to remove trapped air from the water line and to fill the water system During this process the dispenser noise may be loud as the air is purged from the water line system To flush out impurities in the water line throw away the first 6 glassfuls of water NOTE To avoid water deposits the dispenser should be cleaned periodically by wiping with a clean cloth or sponge 10 About autofill To Use HANDS FREE AUTO FILL e Center container on Recess Dispenser Tray not touching bottom sensors and remove hand from container e Press AUTO FILL To Stop AUTO FILL e Press CANCEL to resume filling press AUTO FILL Important Facts about AUTO FILL e For optimum results use a uniform container between 4 8 tall and 2 6 wide Container should be as tall as the bottom sensors e Container shape fill level and functionality may vary on containers taller than 8 e Container volumes may vary if erro
6. to sudden temperature changes or impact such as bumping or dropping Tempered glass is designed to shatter into many small pieces if it breaks Keep fingers out of the pinch point areas clearances between the doors and between the doors and cabinet are necessarily small Be careful closing doors when children are in the area Do not touch the cold surfaces in the freezer compartment when hands are damp or wet skin may stick to these extremely cold surfaces Do not refreeze frozen foods which have thawed completely Use a sturdy glass when dispensing ice on models with ice dispenser INSTALLATION WARNING Explosion Hazard Keep flammable materials and vapors such as gasoline away from refrigerator Failure to do so can result in fire explosion or death GEAppliances com SAFETY CONT CE Tip Over Hazard Built in style models model PYE CYE and PWE are top heavy especially with any doors open These models must be secured with the anti tip floor bracket to prevent tipping forward which could result in death or Serious injury Read and follow the entire installation instructions for installing the anti tip floor bracket packed with your refrigerator CONNECTING ELECTRICITY WARNING u Electrical Shock Hazard Plug into a grounded 3 prong outlet Do not remove the ground prong Do not use an adapter Failure to follow these instructions can result in death fire or electrical shock
7. Do not under any circumstances cut or remove the third ground prong from the power cord PS w For personal safety this appliance must be properly grounded The power cord of this appliance is equipped with a 3 prong A 115 Volt AC 60 Hz 15 or 20 amp fused grounded electrical grounding plug which mates with a standard 3 prong supply is required This provides the best performance and grounding wall outlet to minimize the possibility of electric also prevents overloading house wiring circuits which could shock hazard from this appliance cause a fire hazard from overheated wires Have the wall outlet and circuit checked by a qualified Never unplug your refrigerator by pulling on the power cord electrician to make sure the outlet is properly grounded Always grip plug firmly and pull straight out from the outlet Where a standard 2 prong wall outlet is encountered it is Repair or replace immediately all power cords that have your personal responsibility and obligation to have it replaced become frayed or otherwise damaged Do not use a cord that with a properly grounded 3 prong wall outlet Do not use an shows cracks or abrasion damage along its length or at either adapter end The refrigerator should always be plugged into its own When moving the refrigerator away from the wall be careful individual electrical outlet which has a voltage rating that not to roll over or damage the power cord matches the rating plate PROPER DISPOSAL
8. OF YOUR OLD REFRIGERATOR Suffocation and child entrapment hazard Remove fresh food and freezer doors from the refrigerator prior to disposal Failure to do so can result in child entrapment which can lead to death or brain damage IMPO RTANT Child entrapment and suffocation are not problems of the past Refrigera nts J unked or abandoned refrigerators are still dangerous even if they will sit for just a few days If you are getting rid of your old All refrigeration products contain refrigerants which under refrigerator please follow the instructions below to help prevent federal law must be removed prior to product disposal If you accidents are getting rid of an old refrigeration product check with the company handling the disposal about what to do Before You Throw Away Your Old Refrigerator or Freezer Take off the fresh food and freezer doors Leave the shelves in place so that children may not easily climb inside F READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY N SAVE THESE INSTRUCTIONS 3 About the features
9. Pull the drawer out to the stop position Pull left and right slides until fully Lift the front of the drawer up and out extended Place drawer back in first and rotate drawer front down to seat on slide Push the drawer in to closed position How to Remove and Replace Drawer Divider To remove To replace Pull the drawer out to the stop position D Hook the back of the divider over the Raise the front side of the divider rear wall of the drawer to unhook it from the rear wall of Push the divider down the drawer 16 About the freezer Freezer Basket and Drawer 0 Basket Drawer Utility Bin Ice Bucket NONNE To remove push in plastic tab on either left or right side To replace slide bin into location until it locks into place Basket Removal To remove Standard Depth models only Open freezer door to the stop position Remove freezer door bin by pushing plastic tab on either left or right side to release bin hinge pin Remove freezer basket by lifting up the rear of the basket and moving basket rearward until the front of the basket can be rotated upward and out Lift it out to remove 17 Non Adjustable Bin in the Freezer GEAppliances com To remove PYE and PWE models only Open fresh food doors Open
10. filter Filters water amp Ice About the features Door ice bin 1 Open left fresh food door 2 Pull down latch to release bin door 3 Using handhold lift ice bucket up and out to clear locators in bottom of bin 4 To replace the ice bucket set it on the guide brackets and push until the ice bucket seats properly 5 If bucket cannot be replaced rotate Ice bucket the Ice Bucket Fork 1 4 turn clockwise Drop down dairy bin 1 Open right fresh food 2 Depress both buttons on lower sides and bin will drop down 3 Reverse to reinstall Door ice water filter Remove filter bypass plug Push the indent on the cover and open filter door Pull up on filter bypass plug and pull straight out to remove Installing the filter cartridge Push the indent at the bottom of the cover and open Lift door and align tabs on filter to filter holder and push filter into place Filter cover is designed to be reinstalled if accidently removed Select Models Only os Swing Do not twist GEAppliances com Drop down tray tray open Push Pull Water amp Ice Filter in door or case About the controls with temperature settings PFE29 PYE23P Control Style A LCD External Control l Refrigerator Hold 3 Sec for F C Recommended 37 F Actual Set ay pa F Ltt LA Llc ue Energy Smart Recommende
11. filters only Using GE branded filters in GE and Hotpoint refrigerators provides optimal performance and reliability GE filters meet rigorous industry NSF standards for safety and quality that are important for products that are filtering your water GE has not qualified non GE branded filters for use in GE and Hotpoint refrigerators and there is no assurance that non GE branded filters meet GE s standards for quality performance and reliability If you have questions or to order additional filter cartridges visit our website at www geapplianceparts com or call GE Parts and Accessories 800 626 2002 Customers in Canada should consult the yellow pages for the nearest Camco Service Center GE Appliances Appliance Park Louisville KY 40225 geapplianceparts com RPWF 2012 General Electric Company PC71879 Refer to 239D4126P002 Pub No 31 45497 12 Push Pull About the fresh food storage options Rearranging the Shelves Shelves in the refrigerator compartment are adjustable To remove 7 Remove all items from the shelf Tilt the shelf up at the front Lift the shelf up at the back and bring the shelf out To replace While tilting the shelf up insert the top hook at the back of the shelf in a slot on the track Lower the front of the shelf until the bottom of the shelf locks into place Spillproof Shelves Spillproof shelves have special edges to help prevent spills from dripping to lower
12. in the door ice maker bin Cans bottles or food packages in the storage drawer may cause the ice maker or auger to jam To Use the Internal Water Dispenser The water dispenser is located on the left wall inside the refrigerator compart ment To dispense water Hold the glass against the recess Push the water dispenser button Hold the glass underneath the dispenser for 2 3 seconds after releasing the dispenser button Water may continue to dispense after the button is released Select Models Only If no water is dispensed when the refrigerator is first installed there may be air in the water line system Press the dispenser paddle for at least five minutes to remove trapped air from the water line and to fill the water system To flush out impurities in the water line throw away the first six full glasses of water To remove Dispenser Tray Pull Dispenser Tray out until it stops Locate tab in the center on the bottom and push up Pull Dispenser Tray assembly out Lift metal Dispenser Tray out at center notch to clean To reinstall Dispenser Tray Place the Dispenser Tray cover on top of catch tray and position under the two plastic retainers on either side Center Dispenser tray and align with center guides Push in until it firmly in place To keep dispensed ice from missing the glass put the glass close to but not touching the dispenser opening Some crushed ice may be dispensed even though you
13. products purchased for home use within the U S A In Alaska the warranty excludes the cost of shipping or service calls to your home Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state To know what your legal rights are consult your local or state consumer affairs office or your state s Attorney General For Purchases Made In lowa This form must be signed and dated by the buyer and seller prior to the consummation of this sale This form should be retained on file by the seller for a minimum of two years Buyer Seller Name Name Address Address City State Zip City State Zip Signature o Date Signature Date If your GE part fails because of a manufacturing defect within thirty days from the date of original purchase for use we will give you a new or at our option a rebuilt part without charge Return the defective part to the parts supplier from whom it was purchased together with a copy of the proof of purchase for the part If the part is defective and shows no signs of abuse it will be exchanged The warranty does not cover the failure of parts which are damaged while in your possession are abused or have been installed improperly It does not cover the cost of returning the part to the supplier from whom it was purchased nor does it cover the cost of labor to remov
14. push forward until inserted fully O Push bin down until locked into posi tion Bin hook rear each side Bin locator each side GE Appliances General Electric Company Louisville KY 40225 33 Refer to 239D4129P002 Pub No 31 45498 GEAppliances com Installation Instructions INSTALLING THE WATER LINE BEFORE YOU BEGIN Recommended copper water supply kits are WX8X2 WX8X3 or WX8X4 depending on the amount of tubing you need Approved plastic water supply lines are GE SmartConnect Refrigerator Tubing WX08X10006 WX08X10015 and WX08X10025 When connecting your refrigerator to a GE Reverse Osmosis Water System the only approved installation is with a GE RVKit For other reverse osmosis water systems follow the manufacturer s recommendations If the water supply to the refrigerator is from a Reverse Osmosis RO Water Filtration System AND the refrigerator also has a water filter use the refrigerator s filter bypass plug Using the refrigerators water filtration cartridge in conjunction with the RO water filter can result in hollow ice cubes This water line installation is not warranted by the refrigerator or ice maker manufacturer Follow these instructions carefully to minimize the risk of expensive water damage Water hammer water banging in the pipes in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding Call a qualified plu
15. sediment from the water pipe gt B DRILL THE HOLE FOR THE VALVE Drill a 1 4 hole in the water pipe even if using a self piercing valve using a sharp bit Remove any burrs resulting from drilling the hole in the pipe Take care not to allow water to drain into the drill Failure to drill a 1 4 hole may result in reduced ice production or smaller cubes Installation Instructions INSTALLING THE WATER LINE cont 4 FASTEN THE SHUTOFF VALVE Z CONNECT THE TUBING TO THE VALVE Fasten the shutoff valve to the cold water pipe with the pipe clamp Place the compression nut and ferrule sleeve for copper tubing onto the end of the tubing and connect it to the shutoff valve Pipe ene Make sure the tubing is fully inserted into RS the valve Tighten the compression nut securely For plastic tubing from a GE SmartConnect Refrigerator Tubing kit insert the molded end stds ro Cold Water of the tubing into the shutoff valve and tighten Shutoff Valve Pipe compression nut until it is hand tight then tighten one additional turn with a wrench Over NOTE Commonwealth of Massachusetts tightening may cause leaks Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted Saddle Type in Massachusetts Consult with your licensed shutoff Valve e Compression Nut plumber SmartConnect 5 TIGHTEN THE PIPE CLAMP Tighten the clamp screws until the sealing washer begins to swell
16. shelves Quick Space Shelf This shelf splits in half and slides under itself for storage of tall items on the shelf below This shelf can be removed and replaced or relocated just like spillproof shelves NOTE The location of the upper Quick Space Shelf is not adjustable 13 About the fresh food storage options Non Adjustable Dairy Bin To remove Lift the dairy bin straight up then pull out Adjustable Bins on the Door Adjustable bins can easily be carried from refrigerator to work area To remove Lift bin straight up then pull out To replace or relocate Slide in the bin just above the molded door supports and push down The bin will lock in place See page 33 Non Adjustable Bins on the Door To remove Lift the bin straight up then pull out To replace Engage the bin in the molded supports on the door and push down It will lock in place The ice maker door bins are not interchangeable note the location upon removal and replace the bin in its proper location 14 To replace Engage the bin in the molded door supports and push down The bin will lock in place See page 33 Drop down tray tray open 1 Open right fresh food door 2 Depress both buttons on lower sides of bin and bin will drop down 3 Reverse to reinstall Non Dispense Models Left Hand Door Select Models Only Abou
17. t roll over the power cord or water supply line 1 Turn refrigerator off og 7 or unplug the refrigerator 2 Empty ice bucket 3 Turn water supply off If you cut the water supply off turn off the ice maker pg 18 Upon returning from vacation 1 Replace the water filter 2 Run 2 gallons of water through the cold water dispenser about 5 minutes to flush the system Handle only from the sides of the refrigerator Be sure the refrigerator stays in an upright position during moving Replacing the lights Refrigerator Lights LEDs There is LED lighting in fresh food compartment and on the bottom of the fresh food doors to light the freezer compartment N An authorized technician will need to j replace the LED light SS If this assembly needs to be replaced call 5 GE Service at 1 800 432 2737 SS in the United States or 1 800 561 3344 in Canada AWAY M Select Models Only 20 Installation Instructions Refrigerator GE and GE Profile models Questions Call 800 GE CARES 800 432 2737 or visit our Website at GEAppliances com In Canada call 1 800 561 3344 or visit our Website at www GEAppliances ca BEFORE YOU BEGIN Read these instructions completely and carefully GE Tip over Hazard Built in style models model PYE CYE and PWE are top heavy especially with any doors open These models must be secured with the anti tip floor br
18. to make initial fresh food door adjustment While purging the air from the water system check all water line connections for leaks Check the connection to the household water supply at back of refrigerator and door water line connect If the refrigerator has been stored in a cold environment the LCD may be slow to give a proper display Give the refrigerator enough time to warm up and the display should be okay Do not use wax polish bleach or other products containing chlorine on Stainless Steel panels door handles and trim Check this instruction under Cleaning the Outside for full details 41 GET CONNECTED Manage your appliances from your computer or iPhone Maintenance Alerts ilion it with Get text or email alerts if your Brillion enabled Combine a GE Brillion Get Connected Starter Kit wit appliances need attention as well as reminders your Brillion enabled refrigerator and you ll have insight for regular maintenance like filter changes to help protect your investment and track your energy costs from your computer Remote Controls And that s just the beginning With one GE Nucleus ly Access your refrigerator s Sabbath Mode from included with the Get Connected Starter Kit you can your computer and adjust GeoSpring and GE build a network of GE products enabled with Brillion Thermostat settings from your computer or technology such as the GeoSpring water heater iPhone and the GE Programma
19. water that is microbiologically unsafe or of unknown quality without adequate disinfection before and after the system Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts EPA Establishment Number 070595 MEXx 001 NOTICE To reduce the risk associated with property damage due to water leakage e Read and follow use instructions before installation and use of this system e Installation and use MUST comply with all state and local plumbing codes e Do not install if water pressure exceeds 120 psi 827 kPa If your water pressure exceeds 80 psi you must install a pressure limiting valve Contact a plumbing professional if you are uncertain how to check your water pressure e Do not install where water hammer conditions may occur If water hammer conditions exist you must install a water hammer arrester Contact a plumbing professional if you are uncertain how to check for this condition e Do not install on hot water supply lines The maximum operating water temperature of this filter system is 100 F 38 C e Protect filter from freezing Drain filter when temperatures drop below 33 F 0 6 C e The disposable filter cartridge must be replaced every 6 months at the rated capacity or sooner if a noticeable reduction in flow rate occurs For conditions of use health claims certified by the California Department of Public Health and replacements see performance data sheet Calif
20. Accessories 800 626 2002 in Canada 1 800 661 1616 TOOLS YOU MAY NEED Adjustable Wrench O 1 4 Outer Diameter Compression Nut and Ferrule sleeve Socket Ratchet Driver Phillips Head Screwdriver Flat Head Screwdriver Tape Measure 1 8 3 32 1 4 amp 5 32 Allen Wrenches 1 8 Drill Bit and Electric or Hand Drill CLE e Ce Pencil 1 4 Nut Driver 5 16 Nut Driver e Pliers Torx T20 T25 Installation Instructions DIMENSIONS All measurements are given with leveling leg fully retracted Counter Depth CD Models Only Standard Depth SD Models Only Case Depth w o Doors 29 Height from floor to hinge cover top 69 7 Additional Dimensions 694 69 Height to Top of Cabinet 6 9 Moving THE REFRIGERATOR e Using the chart below determine if the width of your passageway can accommodate the depth of the refrigerator Ensure you have clearance to prevent damage to the refrigerator before safety moving it to the final location e If passageways are large enough to accommodate the refrigerator without removing the handles skip to Step 6 Leave tape film and all packaging on doors until the refrigerator is in the final location e NOTE Use a padded hand truck or moving straps to move this refrigerator Place the refrigerator on the hand truck with
21. Bottom Freezer 3 Refrigerators GEAppliances com Safety Instructions 2 3 Operating Instructions POGtUICS 4 e EAF 4 5 CONUGIS oct 5 coaciaecpewesiuea es 6 9 DISPENSEr cece cece eee ees 10 PONE serisine soret nh i 11 Water Filter aaau 12 Fresh Food Storage Options 13 14 Climate Zone amp Temperature Controlled Drawer susineria 15 16 Freezer occ ccc eee e eee eeeees 17 Automatic Ice maker 0005 18 Care and Cleaning 19 Replacing the Lights 20 Installation Instructions Preparing to Install the Refrigerator usses 21 22 Installing the Refrigerator 23 33 Installing the Water Line 34 36 Troubleshooting Tips 38 39 Normal Operating Conditions 37 Tr th or Mythi sse rncissecerisiss 40 41 Consumer Support GE Brillion Get Connected Starter MiG ce wanutindesees Conaiwens 42 Warranty for U S Customers 43 RPWF Water Filter Cartridge Limited Warranty cece cee eee eee es 44 Performance Data Sheet 45 State of California Water Treatment Device Certificate 008 46 Consumer Support Back Cover Select Models Only Write the model and serial numbers here Serial Find these numbers on a label on the left side near the middle of the refrigerator compartment Owner s Manual and Installation Instructions GE and GE Profile models Models that start with P
22. FE GFE DFE and GNE are Standard Depth Models SD Models that start with PYE and PWE are Counter Depth Models CD a UL 239D4106P009 49 60683 01 13 GE IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING SAFETY IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING GE Appliances website www GEAppliances com For more information on your refrigerator s operation visit REFRIGERATOR SAFETY INFORMATION This is the safety alert symbol This symbol alerts you to potential hazards that can kill or hurt you and others All safety messages will follow the safety alert symbol and the word DANGER WARNING or CAUTION These words are defined as A DANGER WARNING CAUTION Indicates a hazardous situation which if not avoided will result in death or serious injury Indicates a hazardous situation which if not avoided could result in death or serious injury Indicates a hazardous situation which if not avoided could result in minor or moderate injury IMPORTANT SAFETY INSTRUCTIONS WARNIN fg To reduce the risk of fire explosion electric shock or injury when using your refrigerator follow these basic safety precautions This refrigerator must be properly installed and located in accordance with the Installation Instructions before it is used Unplug the refrigerator before cleaning and making repairs NOTE Repairs must be performed by a qualifie
23. Remember a level refrigerator is necessary for getting the doors perfectly even If you need help review the previous section on leveling the refrigerator When When the left the left door is door is lower than higher than the right the right door door Adjustment point If you open the freezer door you can see the center hinge Insert 1 4 Allen wrench into the shaft of the center hinge Adjust the height by turning clockwise or counterclockwise When you turn counterclockwise the door will move up Installation Instructions Non Dispense Models Refrigerator Assembly Instructions suggested assembly Instructions dassemblage du r frigerator dassemblage sugg rer Instrucciones de montaje del refrigerador ensamble sugerido Divider Select models only g i To place bins into doors Match your bin with the letter shown Position the bin hooks over the bin locator and
24. WATER SOUNDS The flow of refrigerant through the cooling coils may make a gurgling noise like boiling water Water dropping on the defrost heater can cause a sizzling popping or buzzing sound during the defrost cycle A water dripping noise may occur during the defrost cycle as ice melts from the evaporator and flows into the drain pan Closing the door may cause a gurgling sound due to pressure equalization Before you Call for service Troubleshooting Tips Q Save time and money Review the charts on the following pages first and you may not need to call for service Possible Causes What to Do Water filter indicator light remains lit after replacing filter Water filter indicator light is not lit Handle is loose handle has a gap Refrigerator beeping Water filter indicator must be reset This is normal This indicator will turn on to tell you that you need to replace the filter soon Handle needs adjusting This is door alarm Non LCD models Press and hold reset button LCD models On the LCD screen select SETTINGS then WATER FILTER Select RESET See About the Water Filter for more information See Attach Fresh Food Handle and Attach the Freezer Handle sections for detailed instructions Turn off or disable with door closed If door open and alarm is sounding you can only snooze the alarm Not cooling The cooling system is off See About Controls Water has poor taste odor
25. a 3 8 hex socket After adjustment tighten the 3 attachment driver screws using to 65 in lb Locate and loosen the cam screw using the T 27 screw driver REMOVE PACKAGING A Remove all tape foam and protective packing from shelves and drawers 28 Installation Anti Tip Floor Bracket Instructions PYE PWE Models Only CE Tip Over Hazard TOOLS YOU WILL NEED 1 8 3 mm Drill Bit and Tape measure Electric or Hand Drill Built in style models model PYE CYE and PWE are r o top heavy especially with any doors open These models must be secured with the anti tip floor Pencil bracket to prevent tipping forward which could result in death or serious injury Read and follow the entire installation instructions for installing the anti tip floor bracket packed with your refrigerator Ole THE ANTI TIP FLOOR NOTE A Place the anti tip floor bracket locator template If you did not receive an anti tip bracket with your re Mi ae ae ae ee ee gs ee ea One etna with the desired location of the RH side of the In a a Call 1 099 aaa TEFEN refrigerator see Figure 1 ene of the bracket visit www Figure 1 Installation Overview In Canada www GEAppliances ca nar Concrete oles MATERIALS YOU MAY NEED rot included ee My at Anchor Sleeves i Ss ee Rear RH 1 4 6 mith 1 1 2 38 mm 1 2 12 mm OD ea pone ot i Drill Bit Appropriate for Anchors Base Bracket__ lt 4 RH Side of B
26. a side against the truck We strongly recommend that two people move and complete this installation If your model number starts with PFE SD If your model number starts with GFE DFE GNE SD if your model number starts with CFE SD If your model number starts with CYE PYE PWE CD 2 2 Installation Instructions INSTALLING THE REFRIGERATOR REFRIGERATOR LOCATION e Do not install the refrigerator where the temperature will go below 60 F 16 C because it will not run often enough to maintain proper temperatures Do not install the refrigerator where the temperature will go above 100 F 37 C because it will not perform properly Install it on a floor strong enough to support it fully loaded CLEARANCES Allow the following clearances for ease of installation proper air circulation and plumbing and electrical connections Sides 1 8 3 mm Top 1 25 mm Cabinet Hinge Cover Back 2 60mm REMOVING THE REFRIGERATOR DOORS e IMPORTANT NOTE This refrigerator is 361 4 deep 311 4 for CD models Doors and passageways leading to the installation location must be at least 361 4 wide in order to leave the doors and handles attached to the refrigerator while transporting it into the installation location If passageways are less than 361 4 the refrigerator doors and handles can easily be scratched and damaged The top cap and doors can be removed to allow the refrigerator to be safely moved indoor
27. acket to prevent tipping forward which could result in death or serious injury Read and follow the entire installation instructions for installing the anti tip floor bracket packed with your refrigerator IMPORTANT Observe all governing codes and ordinances Save these instructions for local inspector s use Note to Installer Be sure to leave these instructions with the Consumer Note to Consumer Keep these instructions for future reference Skill level Installation of this appliance requires basic mechanical skills Completion time Refrigerator Installation can vary Water Line Installation 30 minutes Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the Warranty PREPARATION MOVING THE REFRIGERATOR INDOORS If the refrigerator will not fit through a doorway the refrigerator door and freezer drawer can be removed e To remove the refrigerator door see the Installing the Refrigerator section e To remove the freezer drawer see the Removing the Freezer Drawer section WATER SUPPLY TO THE ICE MAKER AND DISPENSER If the refrigerator has an ice maker it will have to be connected to a cold water line A GE water supply kit containing tubing shutoff valve fittings and instructions is available at extra cost from your dealer by visiting our website at GEAppliances com in Canada at www GEAppliances ca or from Parts and
28. against the rear wall Refer to 239D1142P001 Pub No 31 45484 2 Installation Instructions INSTALLING THE REFRIGERATOR cont CONNECTING THE REFRIGERATOR If you are using copper tubing insert the end of the TO THE HOUSE WATER LINE A cold water supply is required for automatic ice maker operation If there is not a cold water supply you will need to provide one See Installing the Water Line section NOTES e Before making the connection to the refrigerator be sure the refrigerator power cord is not plugged into the wall outlet tubing into the refrigerator connection at the back of the refrigerator as far as possible While holding the tubing tighten the fitting If you are using GE SmartConnect tubing insert the molded end of the tubing into the refrigerator connection at the back of the refrigerator and tighten the compression nut until it is hand tight Then tighten one additional turn with a wrench Over tightening may cause leaks e If your refrigerator does not have a water filter we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator s water valve Install it in the water line near the refrigerator If using GE SmartConnect Refrigerator Tubing Kit you will need an additional tube WX08X10002 to connect the filter Do not cut plastic tube to install filter e Before connecting the water line to the house purge the house line for a
29. arm Sounds to alert when the freezer or fresh food doors have been left open Reset filter Press and hold for 3 seconds after replacing the filter Photo upload Insert USB memory stick to upload personal photos to the refrigerator LCD screen LCD will provide on screen prompts to load and view slideshow USB Cover Additional settings e Photo upload and delete e Slideshow e Connected Home ready e Reset water filter e Ice maker on off e Door alarm e Sound control e Cooling system On Off e Metric English units e Auto fill video turorial Additional Modes e Sabbath Mode Press and hold lock amp light simultaneously for 3 seconds to enter exit Sabbath mode Activate Sabbath Mode to turn off interior lights temperature control and advanced features Compressor will run on a timed defrost when in Sabbath mode x About the controls features GEAppliances com GFE29 GFE27 Control Style C External Controls DFE29 Ice Top ON OFF EnergySmart Ice Bottom ON OFF 7 Replace Water Filter Lock Controls Reset Dispenser Controls Style D Internal Controls GNE26 PWE23 reee O ae rr WA Ac Energy Smart Recommended 0 F _ 9 Boogart sno on ide Ice Maker 19 pods controls 0 re O Door Alarm O Freezer temp control Sounds to alert when the freezer or fresh food Adjust freezer compartment temperature doors have been left open Refrigerator temp
30. ately WOOD Wall and TILE Floor Construction e For this special case locate the 2 wall holes identified in Fig 1 Drillan angled 1 8 3 mm pilot hole approx as shown in Fig 3 in the center of each hole e Mount the anti tip floor bracket using the Minimum Acceptable Installation 1 as illustrated in Fig 2 POSITIONING THE REFRIGERATOR TO ENGAGE THE ANTI TIP FLOOR AND BASE BRACKETS Before pushing the refrigerator into the opening plug the power cord into the receptacle and connect waterline if equipped Check for leaks Locate the refrigerator s RH side and move back approximately in line with the RH side of the cabinet opening W This should position the anti tip floor bracket to engage the anti tip base bracket on the refrigerator Gently roll the refrigerator back into the cabinet opening until it comes to a complete stop Check to see if the refrigerator front lines up with the cabinet front face If not carefully rock the refrigerator forward and backward until engagement occurs and you notice that the refrigerator is fully pushed up against the rear wall D If Applicable Adjust the rear and front wheel height settings to fully engage the rear anti tip brackets while also aligning the refrigerator front with the cabinet front face NOTE If you pull the refrigerator out and away from the wall for any reason make sure the anti tip floor bracket is engaged when the refrigerator is pushed back
31. ays be removed for MYTH Check chart on reverse side of this instruction If the doors must be installation removed do not remove the handles or if the refrigerator will fit easily through the passage way opening Adjust handles that are loose or have a gap by adjusting 1 8 set screws on either end of handles 40 Before you call for service review the detailed troubleshooting tips in the Owner s SERVICE manual if needed service can be scheduled by visiting us online GEAppliances com or calling 800 ge CARES 800 432 2737 Truth or Myth cont Truth or Myth Answer Explanation Door removal is always required for installation Refrigerator doors that won t close after installation can be adjusted to close properly There is an adjustment to rear wheels Check for leaks after all water connections are made My LCD display will always be on when plug the power cord in at installation Any packaging residue can be cleaned off the refrigerator using any cleaner Check chart on reverse side of this instruction Doors should only be removed when necessary to prevent damage from passage way or access to final location Door mechanism works best if installed at 90 If installed at 180 remove the door from the mid hinge and swing the door 180 before reinstalling See Reinstalling the Refrigerator Doors Front leveling legs are adjustable and should be used to balance the refrigerator Leveling legs are used
32. ble Thermostat that you can manage from your computer or iPhone Energy Tracking Track your appliances energy usage iPhone is a registered trademark of Apple Inc Learn More at GEAppliances com connected home manager O dima SPECIAL OFFER a as Save 25 ona GE Brillion Get Connected Starter Kit e Call 800 694 8478 or e Visit GEApplianceParts com and enter the promotion code J OIN when you oy Ey order the Get Connected Starter Kit Part HEKAEQUOV l eee A ay ee es r Offer valid through December 31 2013 42 Refer to 239D3392P001 Pub No 31 49000 Refrigerator Warranty For customers in the United States All warranty service provided by our Factory Service Centers or C an authorized Customer Care technician To schedule service visit us online at GEAppliances com or call 800 GE CARES 800 432 2737 Please have serial number and model number available when calling for service Staple your receipt here Proof of the original purchase date is needed to obtain service under the warranty Servicing your refrigerator may require the use of the onboard data port for diagnostics This gives a GE Factory Service technician the ability to quickly diagnose any issues with your appliance and helps GE improve its products by providing GE with information on your appliance If you do not want your appliance data to be sent to GE please advise your technician NOT submit t
33. control O Reset Filter Adjust fresh food compartment temperature Hold for 3 seconds after replacing filter Dual ice maker control 3 Lock Controls Turn your ice makers on off Press and hold 3 seconds to lock out ice and water dispenser and all O TurboCool setting feature and temperature buttons Activate TurboCool to quickly restore refrigerator temperature after frequent door openings 2 LED dispenser light LED lighting that can be turned on off to light Ice maker setting your dispenser 2 Turn your ice makers on off Select Models Only About the dispenser Water amp Ice Dispenser See About the controls with temperature settings amp About the control features Dispenser tray WARNING Laceration Hazard Never put fingers or any other object into ice crusher discharge opening Doing so can result in contacting the ice crushing blades and lead to serious injury or amputation Use a sturdy glass when dispensing ice A delicate glass may break and result in personal injury Important Facts About Your Dispenser Do not add ice from trays or bags to the door ice maker bucket It may not crush or dispense Avoid overfilling glass with ice and use of narrow glasses Backed up ice can jam the chute or cause the door in the chute to freeze shut If ice is blocking the chute remove the ice bucket poke it through with a wooden spoon Beverages and foods should not be quick chilled
34. d 0 F Freezer Pasarela i A Energy Smart Override Hold 3 Seconds _ Lock Controls Reset Filter Replace Water Filter Light l Door Alarm l Ice Maker GFE29 GFE27 DFE29 Control Style C External Control GNE26 PWE23 Control Style D Internal Control Lock Controls Hold 3 Seconds Freezer Refrigerator Cece acer at aE Lt Actual Temp Hold 3 sec Set Temp IceTop ONOFF EnergySmart Reset Filter Hold 3 Seconds Ice Ice Bottom ON OFF Turbo Door Maker Replace Water Filter Cool Lock Controls Alarm Ri Di Cor ower eae q NOTE The refrigerator is shipped with protective film covering the temperature controls If this film was not removed during installation remove it now The temperature controls are preset in the factory at 37 F for the refrigerator compartment and 0 F for the freezer compartment Allow 24 hours for the temperature to stabilize to the preset recommended settings The temperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer The actual temperature may vary slightly from the SET temperature based on usage and operating environment About the controls with temperature settings Changing the Temperature for Control Style A To Change the Refrigerator Temperature Access By Temperature Button Activate By Below the word Refrigerator use the arrows to select
35. d Service Professional Replace all parts and panels before operating Because of potential safety hazards under certain conditions we strongly recommend against the use of an extension cord However if you must use an extension cord it is absolutely necessary that it be a UL listed in the United States or a CSA certified in Canada 3 wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes minimum and 120 volts To prevent suffocation and entrapment hazards to children Remove the fresh food and freezer doors from any refrigerator before disposing of it or discontinuing its use Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance Power to the refrigerator cannot be disconnected by any setting on the control panel refrigerator must be unplugged to remove power Do not allow children to climb stand or hang on the door handles or the shelves in the refrigerator They could seriously injure themselves In refrigerators with automatic ice makers avoid contact with the moving parts of the ejector mechanism or with the heating element that releases the cubes Do not place fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in Do not clean glass shelves or covers with warm water when they are cold Glass shelves and covers may break if exposed
36. d reinstall filter cartridge being certain that it locks in place Ice maker is turned off Check that the ice maker is turned on See About the Automatic Ice Maker Water is leaking from dispenser Air may be present in the water line Dispense water for at least 5 minutes to system causing water to drip after remove air from system being dispensed Photos not found Photos not in root directory of USB Make sure the photos are in the root direc tory in your USB Photos not in J PEG format Photos must be in J PEG format Camera PC used with USB cord Must use a USB drive AUTO FILL under fill no fill Not all containers work with Try different container AUTO FILL e Container not found See pg 11 e Unstable container e Misaligned container AUTO FILL overfills Not all containers work with Try different container AUTO FILL PRECISE FILL will not fill container Normal PRECISE FILL requires use of Fora specific amount of water select PRE dispenser paddle CISE FILL to dispense water Freezer cooling fresh food not cooling Normal when refrigerator first Wait 24 hours for temperature in both plugged in or after extended power compartments to reach selected outage temperatures Ice dispenser opens after closing Normal The ice dispenser door may open after freezer drawer closing freezer door to allow access Select Models Only 39 Before you call for service review the detailed troubleshooting tips in the Owner s SERVICE man
37. e or install it to diagnose the fault It does not cover parts used in products in commercial use except in the case of air conditioning equipment In no event shall GE be liable for consequential damages Warrantor General Electric Company EXCLUSION OF IMPLIED WARRANTIES Your sole and exclusive remedy is part exchange as provided in this Limited Warranty Any implied warranties including the implied warranties of merchantability or fitness for a particular purpose are limited to six months or the shortest period allowed by law GE Appliances Appliance Park Louisville KY 40225 geapplianceparts com 2012 General Electric Company PC66596 44 Performance Data Sheet Model GE RPWF Use Replacement Cartridge RPWF The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal tothe permissible limit for water leaving the system as specified in NSF ANSI Standard 42 and Standard 53 System tested and certified by NSF International against NSF ANSI Standard 42 and Standard 53 for the reduction of substances listed below Capacity 170 Gallons 643 5 Liters _ Contaminant Reduction Determined by NSF testing Average Product Max Permissible Substance Tested NSF specified Avg Water Product Water NSF Reduction NSF for Reduction Average Influent Challenge Concentration Reduction Concentrat
38. efrigerator but it does not shut off the electrical power NOTE For optimal temperature performance we recommend to avoid placing food items directly at the air flow vents of the fresh food air tower and thus blocking the air flow About the controls features Control Style A External Controls PFE29 PYE23P 7 Hands free Autofill Hands free Autofill uses sensors to monitor container height to automatically dispense filtered water without having to activate the paddle PreciseFill setting Precisely dispenses filtered water in accurate measurements in ounces cups quarts or liters using paddle Refrigerator temp control Adjust freezer compartment temperature Fresh food temp control Adjust fresh food compartment temperature TurboFreeze setting Activate TurboFreeze to quickly restore freezer temperatures after frequent door openings TurboCool setting Activate TurboCool to quickly restore fresh food temperature after frequent door openings Lock controls Press and hold 3 seconds to lock out ice and water dispenser and all feature and temperature buttons LED dispenser light LED lighting that can be turned on off to light your dispenser Select Models Only 98 PFE27 PYE23K Control Style B External Controls Turbo Freeze Turbo Cool Lock Controls Light C Door Alarm a Replace Water Filter Reset Filter P Door Al
39. emperature changes or impact such as bumping or dropping Tempered glass is designed to shatter into many small pieces if it breaks Behind the Refrigerator Be careful when moving the refrigerator away from the wall All types of floor coverings can be damaged particularly cushioned coverings and those with embossed surfaces Raise the leveling legs located at the bottom front of the refrigerator Preparing for Vacation For long vacations or absences remove food and unplug the refrigerator Clean the interior with a baking soda solution of one tablespoon 15 ml of baking soda to one quart 1 liter of water Leave the doors open LCD Models turn refrigerator off at control pg 7 If the temperature can drop below freezing have a qualified service technician drain the water supply system to prevent serious property damage due to flooding Preparing to Move Secure all loose items such as shelves and drawers by taping them securely in place to prevent damage When using a hand truck to move the refrigerator do not rest the front or back of the refrigerator against the hand truck This could damage the refrigerator 19 Pull the refrigerator straight out and return it to position by pushing it straight in Moving the refrigerator in a side direction may result in damage to the floor covering or refrigerator Lower the leveling legs until they touch the floor When pushing the refrigerator back make sure you don
40. ence Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty should the need arise You may also mail in the pre printed registration card included in the packing material In Canada www GEAppliances ca Printed in United States
41. etting of circuit breakers Replacement of the light bulbs if included or water filter cartridge if included other than as noted above Damage to the product caused by accident fire floods or acts of God Incidental or consequential damage caused by possible defects with this appliance Product not accessible to provide required service Damage caused by a non GE Brand water filter Damage caused after delivery Replacement of the water filter cartridge if included due to water pressure that is outside the specified operating range or due to excessive sediment in the water supply EXCLUSION OF IMPLIED WARRANTIES Your sole and exclusive remedy is product repair as provided in this Limited Warranty Any implied warranties including the implied warranties of merchantability or fitness for a particular purpose are limited to one year or the shortest period allowed by law This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA If the product is located in an area where service by a GE Authorized Servicer is not available you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service location for service In Alaska the warranty excludes the cost of shipping or service calls to your home Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you
42. fied for cyst reduction may be used on disinfected waters that may contain filterable cysts 46 Consumer Support GE Appliances Website In the US GEAppliances com Have a question or need assistance with your appliance Try the GE Appliances website 24 hours a day any day of the year For greater convenience and faster service you can now download Owner s Manuals order parts or even schedule service on line In Canada www GEAppliances ca Schedule Service In the US GEAppliances com Expert GE repair service is only one step away from your door Get on line and schedule your service at your convenience any day of the year Or call 800 GE CARES 800 432 2737 during normal business hours In Canada call 1 800 561 3344 Real Life Design Studio In the US GEAppliances com GE supports the Universal Design concept products services and environments that can be used by people of all ages sizes and capabilities We recognize the need to design for a wide range of physical and mental abilities and impairments For details of GE s Universal Design applications including kitchen design ideas for people with disabilities check out our Website today For the hearing impaired please call 800 TDD GEAC 800 833 4322 In Canada contact Manager Consumer Relations Mabe Canada Inc Suite 310 1 Factory Lane Moncton N B ELC 9M3 Extended Warranties In the US GEAppliances com Purchase a GE extended warranty and learn about special di
43. filter status Non touch Screen Models A filter indicator light or message will illuminate on the screen when the water filter needs to be replaced This light must be reset by pressing and holding the Reset Filter button for three seconds The filter cartridge has a maximum life of six months and should be replaced when indicated by the filter indicator on the refrigerator or sooner if a significant reduction in flow occurs Removing the filter cartridge To replace the filter first remove the old cartridge by opening the filter door and pulling on the bottom of the cartridge to allow it to swing outward When the cartridge can no longer swing gently pull to unseat it from the cartridge holder DO NOT TWIST CARTIDGE A small amount of water may drip out Installing the Filter Cartridge 1 Align top of filter with cartridge holder and push until cartridge is fully seated Z WARNING 2 While continuing to ensure cartridge is fully seated in the holder gently swing the filter inward until it is in a vertical position If filter will not swing easily check to ensure filter is properly aligned and fully seated within the cartridge holder Ww Run 2 gallons of water through the cold water dispenser about 5 minutes to remove air from the system A newly installed filter cartridge will cause water to spurt from the dispenser Use a large pitcher or sports bottle to catch the water spray DO NOT use the hot water dispen
44. freezer door to the stop position Remove freezer basket by lifting up the rear of the basket and rotate it upward Lift it out to remove To replace Reverse step 1 thru 4 to replace About the automatic ice maker A newly installed refrigerator may take 12 to 24 hours to begin making ice Ice maker Feeler Arm Automatic Ice Maker The ice maker will produce seven cubes per cycle approximately 100 130 cubes in a 24 hour period depending on freezer compartment temperature room temperature number of door openings and other use conditions The ice maker will fill with water when it cools to 15 F 10 C A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes If the refrigerator is operated before the water line connection is made to the unit or if the water supply to an operating refrigerator is turned off make sure that the ice maker is turned off Once the water has been connected to the refrigerator the ice maker may be turned on See the table below for details You may hear a buzzing sound each time the ice maker fills with water Throw away the first few batches of ice to allow the water line to clear Be sure nothing interferes with the sweep of the feeler arm When the bin fills to the level of the feeler arm the ice maker will stop producing ice It is normal for several cubes to be joined together If ice is not used frequently old ice cubes will bec
45. he data to GE at the time of service For the Period of GE Will Replace GE PROFILE AND GE CAFE MODELS One Year Any part of the refrigerator which fails due to a defect in materials or workmanship From the date of the original During the limited one year warranty GE will also provide free of charge all labor and related purchase service to replace the defective part Thirty Days _ Any part of the water filter cartridge which fails due to a defect in materials or workmanship During ees filter if included this limited thirty day warranty GE will also provide free of charge a replacement water filter rom the original purchase date of the refrigerator cartridge GE PROFILE MODELS ONLY Five Years Any part of the sealed refrigerating system the compressor condenser evaporator an all GE Profile models only connecting tubing which fails due to a defect in materials or workmanship From the date of the During this limited five year sealed refrigerating system warranty GE will also provide free of purchase charge all labor and related service to replace the defective part in the sealed refrigerating system What GE Will Not Cover Service trips to your home to teach you how to use the product Improper installation delivery or maintenance Failure of the product if it is abused misused or used for other than the intended purpose or used commercially Loss of food due to spoilage Replacement of house fuses or res
46. in accordance with local plumbing code requirements WHAT YOU WILL NEED e Copper or GE SmartConnect Refrigerator Tubing kit 1 4 outer diameter to connect the refrigerator to the water supply If using copper be sure both ends of the tubing are cut square To determine how much tubing you need measure the distance from the water valve on the back of the refrigerator to the water supply pipe Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall after installation GE SmartConnect Refrigerator Tubing Kits are available in the following lengths 6 1 8m WX08X10006 15 4 6m WX08X10015 25 7 6m WX08X10025 Installation Instructions INSTALLING THE WATER LINE cont Install the shutoff valve on the nearest frequently used drinking water line WHAT YOU WILL NEED CONT NOTE The only GE approved plastic tubing is that supplied in GE SmartConnect Refrigerator Tubing kits Do not use any other plastic water supply line because the line is under pressure at all times Certain types of plastic will crack or rupture with age and cause water damage to your home e A GE water supply kit containing tubing shutoff valve and fittings listed below is available at extra cost from your dealer or from Parts and Accessories 800 626 2002 in Canada 1 800 661 1616 e A cold water supply The water pressure must be between 20 and 120 psi 1 4 8 1 bar e Power drill e 1 2
47. ion Concentration Requirements Test Report Chlorine Taste and Odor 2 0 mg L 2 0 mg L 10 97 4 0 05 mg L N A 250 J 00102044 Nominal Particulate Class 20 5 to lt 1 0 um 7 633 333 pts mL At least 10 000 particles mL 99 0 71 850 pts ml N A 285 J 00106249 10 to 10 fibers L fibers Asbestos 109 MFL greater than 10um in length 99 99 lt 1 MFL N A 299 J 00102069 Atrazine 0 009 mg L 0 009 mg L 10 94 4 0 0005 mg L 0 003 mg L A J 00102058 Benzene 0 016 mg L 0 015 mg L 10 96 4 0 001 mg L 0 005 mg L A J 00102065 Carbofuran 0 08 mg L 0 08 mg L 10 98 8 0 001 mg L 0 04 mg L A J 00102059 Cyst 104 750 cysts L Minimum 50 000 cysts L 99 99 3 cyst L N A 299 95 J 00102057 Lead pH 6 5 0 140 mg L 0 15 mg L 10 99 3 0 001 mg L 0 010 mg L A J 00102052 Lead pH 8 5 0 158 mg L 0 15 mg L 10 98 3 0 002 mg L 0 010 mg L A J 00102053 Mercury pH 6 5 0 006 mg L 0 006 mg L 10 91 0 0003 mg L 0 002 mg L A J 00102054 Mercury pH 8 5 0 006 mg L 0 006 mg L 10 88 3 0 0007 mg L 0 002 mg L A J 00104087 Lindane 0 002 mg L 0 002 mg L 10 99 0 00002 mg L 0 0002 mg L A J 00102063 P Dichlorobenzene 0 222 mg L 0 225 mg L 10 99 8 0 0005 mg L 0 075 mg L A J 00102067 Toxaphene 0 015 mg L 0 015 mg L 10 93 5 0 001 mg L 0 003 mg L A J 00102061 2 4 D Reduction 0 218 mg L 0 210 mg L 10 99 9 0 0001 mg L 0 07 mg L A J 00102064 VOC 0 278 mg L 0 300 mg L 10 97 7 0 0015 mg L N A 295 J 00102070 Based on the use of Cryp
48. mber to correct water hammer before installing the water supply line to the refrigerator To prevent burns and product damage do not hook up the water line to the hot water line For PFE27 and PYE23K Models If the refrigerator is operated before the water connection is made to the ice maker press and hold both the CRUSHED and CUBED buttons together for 3 seconds to disengage the ice maker When the refrigerator has been connected to the water supply press and hold both the CRUSHED and CUBED buttons together for 3 seconds to re engage the ice maker For Non LCD Models If the refrigerator is operated before the water connection is made to the ice maker press and release the ICE MAKER button on the control panel to disengage the ice maker When the refrigerator has been connected to the water supply press and release the ICE MAKER button on the control panel to re engage the ice maker For PFE29 and PYE23P Models If the refrigerator is operated before the water connection is made to the ice maker see ICE MAKER under SETTINGS menu of the LCD Operations section and follow the screen commands to turn the ice maker OFF Do not install the ice maker tubing in areas where temperatures fall below freezing When using any electrical device such as a power drill during installation be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock or is battery powered All installations must be
49. mullion e Pull the ice bucket forward 18 Select Models Only Care and cleaning of the refrigerator Cleaning the Outside The stainless steel panels door handles and trim Do not use appliance wax polish bleach or other products containing chlorine on stainless steel Stainless steel on some models can be cleaned with a commercially available stainless steel cleaner A spray on stainless steel cleaner works best Cleaning the Inside To help prevent odors leave an open box of baking soda in the refrigerator and freezer compartments Unplug the refrigerator before cleaning If this is not practical wring excess moisture out of sponge or cloth when cleaning around switches lights or controls Use an appliance wax polish on the inside surface between the doors Use warm water and baking soda solution about a tablespoon 15 ml of baking soda to a quart 1 liter of water This both cleans and neutralizes odors Rinse and wipe dry GEAppliances com Silver accented plastic parts Wash parts with soap or other mild detergents Wipe clean with a sponge damp cloth or paper towel Do not use scouring pads powdered cleaners bleach or cleaners containing bleach because these products can scratch and weaken the paint finish Should spill tray need cleaning use lime remover NNO Do not clean glass shelves or covers with warm water when they are cold Glass shelves and covers may break if exposed to sudden t
50. om the HOME screen Page over and tap COOLING SYSTEM OFF Press DONE to return to HOME screen Turning the cooling system off stops the cooling to refrigerator but it does not shut off the electrical power To turn OFF cooling system press and hold the Freezer pads simultaneously for 3 seconds When the cooling system is OFF the display should read 0 FF To turn ON cooling system press either pad The display will show ON and then the actual temperature for the refrigerator and the freezer Turning the cooling system OFF stops the cooling to the refrigerator but it does not shut OFF the electrical power To turn OFF cooling system press and hold the Freezer pads simultaneously for 3 seconds When the cooling system is OFF the display should read OFF To turn ON cooling system press either a pad The display will show the preset temperature settings of 37 F for refrigerator and O F for freezer Turning the cooling system off stops the cooling to refrigerator but it does not shut off the electrical power To turn OFF cooling system press and hold the REFRIGERATOR and FREEZER pads simultaneously for 3 seconds When the cooling system is OFF the display should read OFF To turn ON cooling system press either REFRIGERATOR or FREEZER pad The display will show the preset temperature settings of 37 F for refrigerator and 0 F for freezer Turning the cooling system off stops the cooling to r
51. ome cloudy taste stale and shrink NOTE In homes with lower than average water pressure you may hear the ice maker cycle multiple times when making one batch of ice To minimize the risk of personal injury avoid contact with the moving parts of the ejector mechanism or with the heating element that releases the cubes Do not place fingers or hands on the automatic ice making mechanism while the refrigerator is plugged in How to Turn the Ice Maker On Off Display Type See Page 6 Model How to turn the ice maker on off Control Style A PFE29 PYE23P Use the settings menu on the touchscreen Control Style B PFE27 PYE23K Hold CRUSHED and CUBED together for 3 seconds Control Style C GFE29 27 DFE29 Use the ICE MAKER button on the control Control Style D GNE26 PWE23 Use the ICE MAKER button on the control Ice Box Door Lift and pull s I Ice Bucket and Dispenser e Open the ice box door on inside of the left door e Pull up and out on on the ice bucket in the left hand door to remove it from the compartment i i Extra Ice Storage e To replace the ice bucket set it on the guide brackets and push until the ice bucket seats properly e If bucket cannot be replaced rotate the ice bucket fork 1 4 turn clockwise There is additional ice storage in the freezer compartment drawer e Open the freezer drawer e The ice bucket is located on the left side below the
52. ond person support the door B Start with left hand door first Remove the hinge cover on top of the left refrigerator door by removing all hex screws and pulling it up Do the same for the right hand door and the middle cover Remove the 1 4 hex head screw to disconnect the ground wire from the hinge Remove the 1 4 hex head screw to remove the strain relief from the water line Ground Strain lt screw Relief REMOVE THE REFRIGERATOR DOORS cont D Disconnect the water line from the back of the unit by pressing down on the dark grey collar while pulling up on the water line Pull water line through case conduit from the top to free the line for door removal The water line is more than 4 long and may need to be taped to Door for accessibility when reinstalling Y or Straight Connector E Using a 3 8 socket ratchet driver remove the screws securing the top hinge to the cabinet then lift the hinge straight up to free the hinge pin from the location in the top of the door Lifting Hazard Single person lift could cause injury Use assistance when handling moving or lifting the refrigerator doors Note when removing door to prevent damage to door and electronics carefully place the door in a proper location Note The lower door hinge pin and hinge are keyed and must be matched correctly for the door to self close properly Please follow the directions carefully Installation In
53. one Le For Anti Tip Bracket Mounted on CONCRETE Floors Only A AR Refrigerator Sheet B Place the anti tip floor bracket onto the locator MEASURE CABINET OPENING template with its RH floor holes lined up with the floor holes indicated on the template sheet AVAILABLE VS REFRIGERATOR WIDTH approximately 15 1 4 from the edge of the sheet Measure width of cabinet opening where or the RH side of the refrigerator refrigerator will be placed W Hold down in position and use the anti tip floor Be sure to account for any countertop overhang bracket as a template for marking the holes baseboard thickness and any clearance desired based upon your configuration and type of Width W should not be less than 36 The construction as shown in Step 3 Mark the hole refrigerator will be placed approximately in the locations with a pencil nail or awl middle of this opening NOTE Rear Wall e It is REQUIRED to use at least 2 screws to mount Ee e a the floor bracket one on each side of the aai h Countertop anti tip floor bracket Both must be into either the wall or the floor Figure 2 indicates all the 5 16 8 mm Nut Driver 2 Wall Holes Floor Bracket to Install Whichever Is acceptable mounting configurations for screws Larger Plus Identify the screw holes on the anti tip floor Any Desired bracket for your configuration REFRIGERATOR Clearance Overhang RH Side Refer to 239D1142P001 Pub No 31 45484 2 Front Ins
54. or can safely rest on the bottom Do not rest the door on any other surfaces to avoid scratches Push the slide mechanism back completely until it self retracts 7 REPLACING THE FREEZER DOOR Pull the slide Mechanism to full extension using both hands simultaneously Remove the basket resting on the slides Lifting Hazard Freezer door is heavy Use both hands to secure the door before lifting Lift the freezer door and place it on the slide mechanism Align and insert tab on Freezer Door Bracket with slot on Freezer Slide Bracket D Replace the attachment screws and torque the screws to 65 in lb For adjusting freezer door gaps follow the instructions on pg 27 Replace the basket Installation Instructions INSTALLING THE REFRIGERATOR c cont Instructions for adjusting freezer door gaps IMPORTANT The 6 mounting screws 3 on each side are NOT interchangeable with the center or top hinge screws Drawer screws have flat washer heads and other screws have lines ribs on washer heads After installation of the freezer door check for uniform gaps top and bottom of right and left hand side with the template provided In the event of excessive gaps use the following steps to adjust the freezer door Step 1 Loosen the 3 screws on each side right and left of the freezer door Step 2 Adjust set screw clockwise if gap at the top i
55. ornia Department of Public Health Certification 11 2110 The contaminants or other substances removed or reduced by this water filter are not necessarily in all users water GE Appliances Appliance Park Louisville KY 40225 geapplianceparts com 45 System tested and certified by NSF International against NSF ANSI Standard 42 and Standard 53 in model GE RPWF for the reduction of the claims specified REPLACEMENT ON the performance data sheet 34 8708 7119 0 EPA 070595 MEX 001 2012 General Electric Company PC71879 State of California Department of Public Health Water Treatment Device Certificate Number 11 2110 Date Issued November 16 2011 Trademark Model Designation Replacement Elements GE RPWF RPWEF Manufacturer 3M Purification Inc The water treatment device s listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminants Microbiological Contaminants and Turbidity Inorganic Radiological Contaminants Cysts Asbestos Lead Mercury Organic Contaminants Atrazine Benzene Carbofuran Lindane p Dichlorobenzene Toxaphene CA AB1953 Low Lead Compliant 2 4 D VOC s by chloroform surrogate Rated Service Capacity 170 gallons Rated Service Flow 0 5 gom Conditions of Certification Do not use where water is microbiologically unsafe or with water of unknown quality except that systems certi
56. r Install the water filter bypass plug provided with the refrigerator and check flow from the dispenser If water flow returns to normal with the bypass plug in place replace the water filter The top of the refrigerator doors will always be Several things can affect the fresh food door alignment including the aligned floor the refrigerator is installed on and loading of doors If the top of the fresh food doors are not aligned use a 1 4 allen wrench to adjust the right hand door The adjustment screw is located on the bottom right hand side of the door open the freezer door to access the screw The left hand fresh food door may be raised using spacers Call 800 GECARES to obtain the spacers Refrigerator door handles can be easily tightened TRUE If door handles are loose or have a gap the handle can be adjusted using a 1 8 allen wrench on set screws located on the ends of the handles There may be odor and taste problems with your ice TRUE After starting the ice maker throw away 24 hours of ice production to avoid odor and taste problems can make fine adjustments to the fresh food doors TRUE If the fresh food doors are not aligned use a 1 4 Allen wrench to adjust to align them the right hand door The adjustment screw is located on the bottom of the right door Open the freezer door to access The left hand fresh food door may be raised using spacers Call 800 GECARES to obtain the spacers Door handles should alw
57. r message Container Not Found is given try a different container e AUTO FILL will time out e Handles and garnishes on the rim of the container my cause overfilling or variation in fill volumes Select Models Only GEAppliances com e Splashing may occur depending on the location of the container water flow rate container shape and ice cubes e Keep sensors clean with a clean damp cloth and do not spray liquid or cleaners directly on sensors e AUTO FILL works best with household water pressure of 60 to 100 psi Sensors I1 About the GE RPWF water filter cartridge Water Filter Cartridge The water filter cartridge is located in one of the following places Bottom freezer BF refrigerators In the water filter compartment on the right side wall of the left hand fresh food door In the fresh food interior on the left side wall near the top When to replace the filter cartridge The filter cartridge should be replaced every six months or earlier if the flow of water to the dispenser or icemaker decreases Touch Screen Models A filter status message will appear on the screen when the water filter needs to be replaced The filter status message must be reset manually The Water Filter Replace status message can be reset by entering the Settings menu from the home screen Then select the Water Filter menu and press the RESET button This will reset the
58. ring the ice bucket maintaining ice at a freezing temperature The hum of the motor closing the ice chute is normal shortly after dispensing ice CLICKS POPS CRACKS and SNAPS You may hear cracking or popping sounds when the refrigerator is first plugged in This happens as the refrigerator cools to the correct temperature Expansion and contraction of cooling coils during and after defrost can cause a cracking or popping sound On models with an ice maker after an ice making cycle you may hear the ice cubes dropping into the ice bucket On models with a dispenser during water dispense you may hear the water lines move at initial dispense and after dispenser button is released START UP COOLING It can take up to 24 hours for the refrigerator and freezer temperatures to match the display During that time refrigerator and freezer door openings should be minimized TIPS Freezer cools first Refrigerator compartment cools last it may take several hours after the freezer Turning off ice maker makes both fresh food and freezer food cool faster WHIR d l You may hear the fans Puny at high speeds This happens when the refrigerator is first plugged in when the doors are opened frequently or when a large amount of food is added to the refrigerator or freezer compartments The fans are helping to maintain the correct temperatures The fans change speeds in order to provide optimal cooling and energy savings
59. s If passageways are less than 311 4 start with Step 1 e f it is not necessary to remove doors skip to Step 11 Leave tape and all packaging on doors until the refrigerator is in the final location e NOTE Use a padded hand truck to move this refrigerator Place the refrigerator on the hand truck with a side against the truck We strongly recommend that TWO PEOPLE move and complete this installation 1 REMOVE THE FRESH FOOD DOOR HANDLE Handle Design varies based on models however Installation is same Stainless steel and plastic handles Q Loosen the set screws with the 1 8 Allen wrench and remove the handle NOTE If the handle mounting fasteners need to be tightened or removed use a 1 4 Allen wrench Mounting Fasteners gt Leave film on until after installation 2 REMOVE THE FREEZER DOOR HANDLE Handle Design varies based on models however Installation is same Stainless steel and plastic handles Q Loosen the set screws with the 1 8 Allen wrench and remove the handle NOTE If the handle mounting fasteners need to be tightened or removed use a 1 4 Allen wrench Mounting Fasteners Leave film on until after installation Reinstall the handles using the same procedure as removing 23 Installation Instructions INSTALLING THE REFRIGERATOR cont 3 REMOVE THE REFRIGERATOR DOORS A Securely tape the door shut with masking tape or have a sec
60. s too big see template Turn the set screw using 3 32 hex key clockwise by quarter to half a rotation Step 3 Adjust set screw counter clockwise if gap at the bottom is too big see template Turn the set screw using 3 32 hex key counter clockwise by quarter to half a rotation Step 4 Tighten the 3 screws on each side right and left Step 5 Re check the gaps using the template and repeat steps 1 to 4 if required and complete with step 5 Fold here for using template Plier ici pour utiliser le gabarit D blelo aqui para usar la plantilla Y A n Y 7 Paso 1 0 600 LJN V 1 Step 4 Etape 4 Template for checking gaps Paso 4 Gap should be 0 6 or below Gabarit pour v rifier les carts L cart doit tre de 0 6 po 1 5 cm ou moins Plantilla para el control de espacios El espacio deber a ser de 0 6 o inferior Set Screw Vis d ajustement Tornillo del Set Step 2 Step 3 Etape 2 Etape 3 Paso 2 Paso 3 Refer to 239D4144P001 Pub No 31 45474 2 27 Installation Instructions INSTALLING THE REFRIGERATOR cont LEVEL THE FREEZER DOOR L9 LEVEL THE FREEZER DOOR Cont Lift the door on the side requiring adjustment rotate the cam to required position 0 Initial position 1 Lift by 0 050 1 Lower by 0 050 2 3 Lower by 0 100 Locate the height adjuster cam in the freezer Lower by 0 150 door Slightly loosen the three door attachment screws on both sides using
61. scounts that are available while your warranty is still in effect You can purchase it on line anytime or call 800 626 2224 during normal business hours GE Consumer Home Services will still be there after your warranty expires In Canada call 1 888 261 2133 Parts and Accessories In the us GEAppliances com Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes VISA MasterCard and Discover cards are accepted Order on line today 24 hours every day or by phone at 800 626 2002 during normal business hours Instructions contained in this manual cover procedures to be performed by any user Other servicing generally should be referred to qualified service personnel Caution must be exercised since improper servicing may cause unsafe operation Customers in Canada should consult the yellow pages for the nearest Mabe service center or call 1 800 661 1616 Contact Us In the US GEAppliances com KoA If you are not satisfied with the service you receive from GE contact us on our Website with all the details including your phone number or write to General Manager Customer Relations GE Appliances Appliance Park Louisville KY 40225 In Canada www GEAppliances ca or write to Director Consumer Relations Mabe Canada Inc Suite 310 1 Factory Lane Moncton N B E1C 9M3 Register Your Appliance In the US GEAppliances com Register your new appliance on line at your conveni
62. ser or hands free auto fill some models until all air is removed from the system Swing 4 Reset Filter Status message Touch Screen Models Access RESET button through the Water Filter menu Non touch Screen Models Press and hold the Reset Filter button for three seconds IAN WARNING Using the hot water dispenser prior to purging air from the system may result in spurting of hot water and lead to hot water scalding Follow the instructions above to purge all air from the system through the cold water dispenser prior to using the hot water dispenser Note It is normal for water to appear discolored during the initial system flush Water color will return to normal after first few minutes of dispensing Filter Bypass Plug To reduce the risk of property damage due to water leakage you MUST use the filter bypass plug when a replacement filter cartridge is not available The dispenser and icemaker will not operate without either the filter or bypass plug installed The bypass plug is installed in the same way as a filter cartridge To reduce the risk associated with choking do not allow children under 3 years of age to have access to small parts during the installation of this product The disposable filter cartridge should be replaced every 6 months at the rated capacity or sooner if a noticeable reduction in flow rate occurs For the maximum benefit of your filtration system GE recommends the use of GE branded
63. specific legal rights and you may also have other rights which vary from state to state To know what your legal rights are consult your local or state consumer affairs office or your state s Attorney General Warrantor General Electric Company Louisville KY 40225 43 RPWF Water Filter Cartridge Limited Warranty stocie your receipt here Proof of the i original purchase Contact us at www geapplianceparts com date is needed to or call 800 GE CARES obtain service under the warranty For The Period Of We Will Replace At No Charge To You Thirty Days Any part of the water filter cartridge which fails due to a defect in materials or From the date of the workmanship during this limited thirty day warranty original purchase What is Not Covered e Service trips to your home to teach you how to use the product e Improper installation e Failure of the product if it is abused misused used for other than the intended purpose or used commercially Replacement of house fuses or resetting of circuit breakers Replacement of the water filter cartridge due to water pressure that is outside the specified operating range or due to excessive sediment in the water supply Damage to the product caused by accident fire floods or acts of God Incidental or consequential damage caused by possible defects with this appliance This warranty is extended to the original purchaser and any succeeding owner for
64. stall door Underside OF Fresh Food Door If door cannot be installed at 90 follow steps below 1 Install door at 180 to case front 2 If space limits opening door to less than 180 then a Remove door carefully turn door upside down b Check alignment of door closure mechanism shaft on underside of door The flats on the shaft should correspond to alignment tab on plastic ring or mark on bottom end cap c If shaft is not aligned to tab mark using 5 32 Allen wrench rotate door closure mechanism shaft counterclockwise for right door and clockwise for left door Then align flat with tab mark d Install the door at 90 Securely tape the door shut with masking tape or have a second person support the door Reinstall the top hinge and torque the screws to 65 in lbs C Be sure to reinstall the ground wire and strain relief to the top hinge D Reinstall hinge cover NOTE Ensure wires are not pinched or under screw bosses before tightening screws Installation Instructions INSTALLING THE REFRIGERATOR cont 6 REMOVE THE FREEZER DOOR Pull the freezer door open to full extension Remove 3 attachment screws located at the bottom on each side of the freezer door using 3 8 hex socket driver RENTED siting Hazara Freezer door is heavy Use both hands to secure the door before lifting Lift the freezer door to disengage it from the slide mechanism T The do
65. structions INSTALLING THE REFRIGERATOR cont REMOVE THE REFRIGERATOR DOORS cont Note for proper installation later please follow the next step carefully Remove the tape and keeping the door as straight as possible open the door to 902 then lift straight up to remove it Lift up amp off center hinge N Bi Open Door to 90 4 REMOVE OPPOSITE DOOR Follow the same procedure on the opposite door There are no wires or water lines on the opposite side REMOVE CENTER HINGE if necessary Remove the 3 8 screws securing the center hinge to the cabinet Use T20 driver to remove outboard screw w Remove Cc center screw Loosen Outer screws 5 REINSTALLING THE REFRIGERATOR DOORS Reverse steps 1 through 4 to reinstall refrigerator follow details below for critical alignments A Reinstall center hinge first and torque the screws to 65 in Ibs With the LH door at 902 to the front of the case lower the refrigerator door onto the center hinge Ensure that the door and hinge align correctly B Rotate doors closed and make sure moveable center sealing portion of the door aligns with the striker If the door will not self close after reinstalling remove door tum door upside down check alignment mark and arrow there is an alignment mark on the door closure mechanism It corresponds to an alignment arrow on the plastic ring Rotate door closure mechanism to align mark and arrow rein
66. t least 2 minutes If you are using copper tubing place a compression nut and ferrule sleeve onto the end of the tubing coming from the house cold water supply If you are using the GE SmartConnect tubing the nuts are already assembled to the tubing Fasten the tubing into the clamp provided to hold it in position You may need to pry open the clamp yar SmartConnect Compression Tubing Nut Ferrule sleeve I G Refrigerator Q Connection Y gt Tubing Clamp Bride Abrazadera del tu 1 4 Tubing Tuyau de 1 4 po Tuber a de 1 4 31 Installation Instructions INSTALLING THE REFRIGERATOR ont Turn the water on at the shutoff valve house water supply and check for any leaks See the grounding information attached to the power cord LEVEL THE REFRIGERATOR The leveling legs have 2 purposes 1 Leveling legs adjust so the refrigerator is firmly positioned on the floor and does not wobble 2 Leveling legs serve as a stabilizing brake to hold the refrigerator securely in position during operation and cleaning The leveling legs also prevent the refrigerator from tipping Turn the leveling legs clockwise to raise the refrigerator counterclockwise to lower it Flat Head Screwdriver NOTICE To avoid possible property damage the leveling legs must be firmly touching the floor LEVEL THE REFRIGERATOR DOORS
67. t the climate zone and temperature controlled drawer GEAppliances com ClimateZone Keep fruits and vegetables organized in separate compartments for easy access Excess water that may accumulate in the bottom of the drawers or under the drawers should be wiped dry o Benes c SS Temperature Controlled Drawer The Temperature Controlled Drawer is a full width drawer with adjustable temperature control This drawer can be used for large miscellaneous items To change setting press select button MEAT BEVERAGE PRODUCE Cold La 32 CHEESE CITRUS SELECT 34 36 38 40 L 2 A CAUTION Laceration Hazard Do not store glass bottles at this setting If Colder ithey are frozen they can break and cause personal injury NOTE when fresh food temperature is set to 40 or higher the temperature controlled drawer can only be set to citrus oat ee Ae eed Select Models Only 15 About the climate zone and temperature controlled drawer How to Remove and Replace the Adjustable Deli Produce Drawer To remove To replace
68. tallation Instructions LOCATING THE ANTI TIP FLOOR BRACKET cont Figure 2 Acceptable Screw Placement Locations Recommended Installation Wood Recommended Installation Concrete Minimum Acceptable 2 Minimum Acceptable 1 Wood Floor Wall Plate Stud Minimum Acceptable 3 Concrete Floor ANTI TIP BRACKET INSTALLATION WOOD Wall and Floor Construction e Drill the appropriate number of 1 8 3 mm pilot holes in the center of each floor bracket hole being used a nail or awl may be used if a drill is not available AND remove the locator template from the floor e Mount the anti tip floor bracket by fastening the 2 or recommended 4 10 16 hex head screws tightly into place as illustrated in Figure 3 Figure 3 Attachment to Wall and Floor Floor Wall Bracket 2 Screws Must Enter Wood or Metal Stud gt Rear RH Corner of the Refrigerator Wall Plate Stud 30 CONCRETE Wall and Floor Construction e Anchors required not provided 4 each 1 4 6 mm x 1 1 2 38 mm lag bolts 4 each 1 2 12 mm O D sleeve anchors e Drill the recommended size holes for the anchors into the concrete at the center of the holes marked in Step 2 e Install the sleeve anchors into the drilled holes Place the anti tip floor bracket as indicated in Step 2 Remove the locator template from the floor e Install the lag bolts through the anti tip floor bracket and tighten appropri
69. ter water dispenses a few drops of water are A few drops of water may fall from the dispenser after the dispenser normal paddle has been released To minimize the drops remove the glass slowly from the dispenser will never see frost inside the freezer compartment Frost inside the freezer typically indicates that the door is not properly sealed or has been left open If frost is found clear the frost using a plastic spatula and towel then check to ensure that no food packages or containers are preventing the freezer door from closing Check the refrigerator control panel to ensure the door alarm is on When the refrigerator is installed or after replac A newly installed refrigerator or water filter contains air in the water lines ing the water filter must dispense water for five Press the dispenser paddle and dispense cold water for at least 5 minutes minutes to remove air from the water line and flush the filter To fill the ice bucket to the maximum capacity Dispensing 3 4 cubes 12 hours and 18 hours after installation allows ice should dispense 12 and 18 hours after installation to disperse within the ice bucket which in turns calls on the ice maker to produce additional ice Normal ice production 100 cubes in 24 hours can use the water filter bypass plug to determine if Decrease in flow from the water dispenser or decreased ice production the filter requires replacement may indicate the need to replace the water filte
70. the desired temperature Press DONE when finished to return to HOME screen To Change the Freezer Temperature Access By Temperature Button Activate By Below the word Freezer use the arrows to select the desired temperature Press DONE when finished to return to HOME screen Changing the Temperature for Control Style B To change the temperature press and release the pad The ACTUAL TEMP light will come on and the display will show the actual temperature To change the temperature tap either the pad until the desired temperature is displayed Changing the Temperature for Control Style C To change the temperature press and release the pad The ACTUAL TEMP light will come on and the display will show the actual temperature To change the temperature tap either the pad until the desired temperature is displayed Changing Temp for Control Style D Temperature Display is located on inside of left hand refrigerator door To change the temperature press and release the REFRIGERATOR or FREEZER pad The ACTUAL TEMP light will come on and the display will show the actual temperature To change the temperature tap either the REFRIGERATOR or FREEZER pad until the desired temperature is displayed GEAppliances com To turn OFF cooling system access SETTINGS from the HOME screen Page over and tap COOLING SYSTEM ON Press DONE to return to HOME screen To turn ON cooling system access SETTINGS fr
71. tosporidium parvum oocysts The following pharmaceutical reduction claims have not been certified by NSF International Claims tested and verified by independent laboratory Max Permissible Contaminant NSF specified Avg Average Product Water Product Water NSF Reduction Average Influent Challenge Concentration Reduction Concentration Concentration Test Report Atenolol 1088 ng L N A 99 5 5 0 ng L N A J 00103221 Fluoxetine 845 ng l N A 99 4 5 0 ng L N A J 00103221 Ibuprofen 898 ng L N A 98 8 9 9 ng L N A J 00103726 Progesterone 945 ng L N A 99 4 5 5 ng L N A J 00103727 Trimethoprim 403 ng L N A 99 5 2 0 ng L N A J 00103221 Application Guidelines Water Supply Parameters Service Flow 0 5 gpm 1 89 lpm Water Pressure 25 120 psi 172 827 kPa Water Supply Potable Water Water Temperature 33 F 100 F 0 6 C 38 C It is essential that the manufacturer s recommended installation maintenance and filter replacement requirements be carried out for the product to perform as advertised See Installation Manual for Warranty information Note While the testing was performed under standard laboratory conditions actual performance may vary Replacement Cartridge RPWF For estimated costs of replacement elements please call 1 800 626 2002 or visit our website at www geapplianceparts com ZA WARNING To reduce the risk associated with ingestion of contaminants e Do not use with
72. ual if needed service can be scheduled by visiting us online GEAppliances com or calling 800 ge CARES 800 432 2737 Truth or Myth Truth or Myth Answer Explanation The refrigerator water filter may require replacement The water filter indicator will indicate the need to replace the water filter even though the filter indicator has not turned red or every six months Water quality varies from city to city if water flow from reads Filter Expired the dispenser slows or ice production decreases the water filter should be replaced even though the filter indicator may not indicate the need for replacement The automatic ice maker in my refrigerator will The refrigerator must be connected to water and the ice maker must be produce ice when the refrigerator is plugged in to a turned on Make sure the ice maker is turned on only after the water line power receptacle is connected and water is turned on The ice maker can be turned on off from the controls and ensure the ice maker is on as indicated on the refrigerator control panel See About the Automatic Ice Maker After the refrigerator has been plugged in and The water dispenser tank located inside the refrigerator stores water connected to water will immediately have unlimited for dispensing The water in this tank requires 24 hours to chill after chilled water available from the water dispenser installation High usage conditions will not allow time for the water to Af

GE 239D4106P009 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents