Flying Mole DADM310 User's Manual
Contents
1. Connecting a Speaker Cable ecsecccocococoocococoooocoooocoooo Strip the cover of the cable by about 10mm 3 8 3 Turn a speaker connector counterclockwise to loosen it Twist the wires until they are stranded securely Insert the whole stranded wires of the cable and turn the speaker connector clockwise to tighten it O X 10mm iz ANN Q Twist the wires of the speaker cable until they are stranded securely and take care not to leave any part of the stranded wires out of the speaker connector when connecting the speaker cable If the wires come in contact with the rear panel or the wires at the positive terminal come in contact with the wires at the negative terminal the protection circuit may be activated to stop the normal operation of the product Caution This product has DC amplifier circuit construction Sound signal goes through no capacitor from input to the speaker output Therefore a little noise may be heard when the power is turned on or off depending on the connected device o Q Maintenance Never use liquids such as benzine thinners etc chemically treated cloths and do not spray any aerosol type insecticides on the amplifier Clean the case using only a soft dry cloth If the amplifier becomes soiled mix a solution Liquids Xx Benzine of water and a neutral detergent then dampen 2 a soft cloth in the solution wring out as much O of the solutio2. O SPEAKER Outputs Used to connect the output signal from the amplifier Connect to the speaker with SP cables OUTPUT Connector Balanced When balanced signals are input the same signals as the input signals are output The signal arrange ment of the BALANCE OUTPUT on this product is 1 GND 2 HOT and 3 COLD AC IN CONNECTOR Used to connect the supplied AC power cable to the amplifier Connect the other end of the AC power cable to household AC outlet REMOTE POWER CONTROL Connectors POUT oe cece ccc ecescccccccvcvccce Used to interlock the power on the device con nected to this product with the activation deacti vation of power on this product Connect these outputs to a Flying Mole product equipped with remote power control trigger inputs IN sccoooooooooooooooooooo Used to interlock the power on this product with the activation deactivation of power on another de vice Connect these inputs to a Flying Mole product equipped with remote power control trigger out puts Turn ON the power switch of the amplifier to use the amplifier with cables connected to these connectors Refer to the owner s manuals of the devices to be connected as well These connectors cannot be used with products from other manufactures or for other purposes than the above mentioned purpose MODE Selector Used to switch if the power is controlled by the POWER switch or by REMOTE POWER CONTROL trigger
3. Q Safety Instructions CAUTION RISK OF ELECTRIC SHOCK Monaural Power Amplifier DO NOT OPEN DAD M3 10 Owner s Manual CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICE ABLE PARTS INSIDE REFER SERVICING TO QUALI FIED SERVICE PERSONNEL THIS SYMBOL INDICATES THAT DANGEROUS THIS SYMBOL INDICATES THAT THERE ARE IMPOR VOLTAGE CONSTITUTING A RISK OF ELECTRIC TANT OPERATING AND MAINTENANCE INSTRUC SHOCK IS PRESENT WITHIN THIS UNIT TIONS IN THE OWNER S MANUAL WITH THIS UNIT WARNING To reduce the risk of fire or electric shock do not expose this apparatus to rain or moisture Thank you for purchasing the DAD M3 10 E The important safety instructions In order to use it in a safe manner please read this Owner s Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including ampli fiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are p
4. front panel of the BALANCE INPUT on this product is is bypassed l l 1 GND 2 HOT and 3 COLD e VARIABLE The level can be adjusted with the LEVEL adjustment knob on the front panel BAL The level can be adjusted with the LEVEL ad justment knob on the front panel 3 When balance signals are input the same signals as the input signals are output The signal arrangement of the BALANCE OUTPUT on this product is 1 GND 2 HOT and 3 COLD e Connection of the REMOTE POWER CONTROL Trigger By connecting the REMOTE POWER CONTROL Trigger the activation deactivation of power on a Flying Mole power amplifier equipped with REMOTE POWER CONTROL Trigger Input can be interlocked with the activa tion deactivation of power on this device Refer to the owner s manuals of the devices to be connected as well before connecting cables 1 Remove the attachment to the REMOTE POWER CONTROL connec tors 2 Remove insulation material around the ends of the supplied remote con nection cables and twist the wires until they are stranded securely 3 Insert the wires into the holes in the attachment and tighten the screws to fix the cables Be sure to check polarity before connection Remote connection cable 4 Connect the other ends of the cables to the connector for the device whose power is to be interlocked as in the steps 1 to 3 above The connector is also attached to the device to be connected 4 Connect the con
5. OT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AND DO NOT PUT ANY WATER SOURCE NEAR THIS APPARATUS SUCH AS VASE FLOWER POT COSMETICS CONTAINER AND MEDICINE BOTTLE ETC Remote Connection Remote Power Control e Owner s Manual Cable 2m x 1 AC Power Cable x 1 Connector x 2 this booklet x 1 IMPORTANT NOTICE a XN DAD M310 Owner s Manual Q Features Equipped with high speed floating full resonance switching regulator Flying Mole Bi Phase PWM amplifier technology realizes a new level of high sound quality with stunning high speed responsiveness and wide dynamic range Equipped with real time current limiter Gorgeous parts for uncompromising standards General purpose input interface allows connection with various types of preamplifiers o Q Component Names E Front Panel kee DAD M310 rav IGITAL POWER AMPLIFIER Te MOLE DI Power Switch Power Indicator Used to turn the amplifier s power ON or OFF The ON indicator blue lights when the power is turned on When the power amplifier is on standby in REMOTE ON MODE refer to the SLEEP indicator orange is on LEVEL Adjustment Knobs Used to control the output level Setting the knob to 0 turns down the level to the minimum E Rear Panel INPUTS INPUT Selector Used to connect the input signal to the amplifier Connect an input to a pream
6. ithout notice E6 Dimensions ar e FEO O S eo m 5 A 7 aa La 3 8 tow 5 u i t 2 210 8 1 4 2 S 1 16 214 8 7 16 Jane FY ry z amp e EJ ge sf E je S Unit mm This product should be placed close to the main source of electrical power wall outlet in your house and keep the power plug within reach Connectors names may be different from this manual Refer to the owner s manuals of the equipments to be connected as well 4 BALANCE SIGNAL PARALLEL CONNECTION Outputs from a preamplifier or a CD player can be input to more than one power amplifiers by connecting as shown below Power can be interlocked by using REMOTE POWER CONTROL trigger connectors Refer to the Connection of the REMOTE POWER CONTROL Trigger section for information about REMOTE POWER CONTROL Preamplifier CD Player etc UNBAL INPUT BAL OUTPUT REMOTE POWER CONTROL MODE i 4 E m sari 4 16 Q SPEAKER 4 160 HAUT PARLEUR
7. n as possible and clean the am plifier Then use a soft dry cloth to wipe the ft cloth surface dry sorbent Neutral detergent Privacy Policy Security of Collected Information We maintains strict physical electronic and administrative safeguards to protect your personal information from unauthorized or inappropriate access We restricts access to information about you to who need to know the information to respond to your inquiry or request Who misuse personal information are subject to disciplinary action esr This document is printed with soy ink l FLYING MOLE CORPORATION an organic ink made from soy oil on 5199 1 Waji cho Hamamatsu 431 1115 Japan recycled paper Environmentally friendly printed matter Tel 81 53 486 6030 Fax 81 53 486 6033 FLYIN G M 0 LE http www flyingmole co jp FP40697 000
8. nectors to the REMOTE POWER CONTROL connec Be sure to check polarity before tors of the amplifier and of the other product connection e To control the power of the amplifier from the other product connect the con Connect the black cable to the nectors to the IN of this product and to the OUT of the other product negative terminal e To control the power of the other product from this product connect the con nectors to the OUT of the amplifier and to the IN of the other product Commercially available vinyl insulated cables can be used as well Compatible cable type is AWG24 to AWG12 Refer to the steps 1 through 4 above when connecting cables and make sure that the polarity is correct O Specifications Rated Output 300W 49 100W 8Q Total Harmonic Distortion 0 05 90W 8Q 1kHz Frequency Response DC 20kHz 0dB 0 5dB 82 DC 50kHz 0dB 3dB 8Q S N Ratio 120dB IHF A INput short circuited Input Sensitivity UNBAL 1V BAL 2V Input Impedance FIXED 100k VARIABLE 47kQ BAL UNBAL Vol MAX Power Consumption 55W Power Supply AC 120V 60Hz U S A AC 230V 50Hz Use Environment 0 C 40 C Dimensions inch mm 8 7 16 W x 3 9 16 H x 15 15 16 D 214 W x 91 H x 405 D Weight 4 0 kg 8 8 Ibs Nameplate is on the bottom of the product Due to product improvement specifications and or product design are subject to change w
9. plifier etc Select one of the following settings depending on which input is connected INPUT UNBAL FIXED The LEVEL adjustment knob on the front panel is bypassed Pe a UNBAL BAL PAE FIXED VARIABLE Switch position left If this product is found to be the source of interference which can be determined by turning the unit OFF and ON please try to eliminate the problem by using one of the following measures Relocate either this product or the device that is being affected by the interference Utilize power outlets that are on different branch circuit breaker or fuse circuits or install AC line filter s In the case of radio or TV interference relocate reorient the antenna If the antenna lead in is 300 ohm ribbon lead change the lead in to coaxial type cable If these corrective measures do not produce satisfactory results please contact the local retailer authorized to distribute this type of product If you can not locate the appropriate retailer please contact Flying Mole Corporation Component Names INPUT UNBAL VARIABLE The level can be adjusted with the LEVEL adjust ment knob on the front panel UNBAL BAL uea mi O gt FD WE FIXED VARIABLE Switch position center INPUT BAL VARIABLE The level can be adjusted with the LEVEL adjust ment knob on the front panel UNBAL BAL TIT FIXED VARIABLE Switch position right
10. rovided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over AA 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operated normally or has been dropped Manual thoroughly before using Also keep this manual for future reference PAN eo SN o DAD M310 FLYING MOLE DIGITAL POWER AMPLIFIER E Accessory Checklist Before proceeding with the setup make sure that the following accessory is included in the package If it is missing please contact the dealer whom you purchased the amplifier from or Flying Mole Corp THE APPARATUS IS NOT WATERPROOF TO PREVENT FIRE OR SHOCK HAZARD DO N
11. signals MANUAL ON MODE ccccceccccccece The power is turned ON or OFF with the POWER switch on this product REMOTE ON us on Li The power is not switched by REMOTE POWER CON TROL trigger signals REMOTE ON MODE e ee o oo o0 ooooo The power is interlocked with the activation deac tivation of power on the device connected to the REMOTE POWER CONTROL IN of this prod uct REMOTE ON MANUAL ON lum Set the POWER switch of this product to ON posi tion The REMOTE POWER CONTROL function does not work if the POWER switch is turned OFF Connections E Connecting Devices Make sure the power of all related equipments is turned off when wiring and checking their polarity Make sure that the cable is not shorted when connecting the speaker cable Connect the power cable after all connections are complete Preamplifier CD Player etc Power Amplifier etc w e e e e i m 1 om e 7 Mo O nS o wa O a oy aiu V EA Oa a o o x C a m BE Speaker oer O O paua z s OO Ne ES cusfewane N 416l SPEAKER l D l AC Power Cable 1 Select an input with the selector on the rear panel of the 2 XLR cables can be used to connect BALANCE outputs amplifier of a CD player preamplifier etc The signal arrangement FIXED The LEVEL adjustment knob on the
Download Pdf Manuals
Related Search