Home

Continental Refrigerator 22 User's Manual

1. Installation Instructions 12 REHANG REFRIGERATOR DOOR A Lower the refrigerator door onto the center hinge pin Insert the top hinge pin into the hinge hole on top of the refrigerator door Make sure the door is aligned with the cabinet Attach the hinge to the top of the cabinet loosely with the bolts Make sure the gasket on the door is flush against the cabinet and is not folded Support the door on the handle side and make sure the door is straight and the gap between the doors is even across the front While holding the door in place tighten the top hinge screws Replace the hinge cover 29 Installation Instructions INSTALLING THE WATER LINE IcEMAKER MODELS BEFORE YOU BEGIN Recommended copper water supply kits are WX8X2 WX8X3 or WX8X4 depending on the amount of tubing you need Approved plastic water supply lines are GE SmartConnect Refrigerator Tubing WX08X10002 WX08X10006 WX08X10015 and WX08X10025 When connecting your refrigerator to a GE Reverse Osmosis Water System the only approved installation is with a GE RVKit For other reverse osmosis water systems follow the manufacturer s recommendations If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System AND the refrigerator also has a water filter use the refrigerator s filter bypass plug Using the refrigerator s water filtration cartridge in conjunction with the RO filter can result in ho
2. Installation Instructions INSTALLING THE REFRIGERATOR REFRIGERATOR LOCATION e Do not install the refrigerator where the temperature will go below 60 F 16 C because it will not run often enough to maintain proper temperatures e Do not install the refrigerator where the temperature will go above 100 F 37 C because it will not perform properly e Install it on a floor strong enough to support it fully loaded CLEARANCES Allow the following clearances for ease of installation proper air circulation and plumbing and electrical connections Sides 1 8 4 mm Top 1 25 mm Back 1 25 mm 17 14 CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE icemaker models A cold water supply is required for automatic icemaker operation If there is not a cold water supply you will need to provide one See nstalling the Water Line section NOTES e Before making the connection to the refrigerator be sure the refrigerator power cord is not plugged into the wall outlet e f your refrigerator does not have a water filter we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator s water valve Install it in the water line near the refrigerator If using GE SmartConnect Refrigerator Tubing Kit you will need an additional tube WX08X10002 to connect the filter Do not cut plastic tube to install filter Installation Instruction
3. 2 4 m coiled into 3 turns of about 10 25 cm diameter to allow the refrigerator to move out from the wall after installation GE SmartConnect Refrigerator Tubing Kits are available in the following lengths 2 0 6 m WxX08X10002 6 1 8 m WX08X10006 15 4 6 m WxX08X10015 25 7 6 m WX08X10025 Be sure that the kit you select allows at least 8 2 4 m as described above Installation Instructions Install the shutoff valve on the nearest frequently used drinking water line WHAT YOU WILL NEED CONT NOTE The only GE approved plastic tubing is that supplied in GE SmartConnect Refrigerator Tubing kits Do not use any other plastic water supply line because the line is under pressure at all times Certain types of plastic will crack or rupture with age and cause water damage to your home e A GE water supply kit containing tubing shutoff valve and fittings listed below is available at extra cost from your dealer or from Parts and Accessories 800 626 2002 in Canada 1 888 261 3055 e A cold water supply The water pressure must e Power drill e 1 2 or adjustable wrench e Straight and Phillips blade screwdriver eS e Two 1 4 outer diameter compression nuts and 2 ferrules sleeves to connect the copper tubing to the shutoff valve and the refrigerator water valve OR e If you are using a GE SmartConnect Refrigerator Tubing kit the necessary fit
4. Too frequent or too long door openings Leveling legs need adjusting This is normal if after popping open the freezer door drawer closed on its own e See Care and cleaning e Wipe surface dry and reset the refrigerator control one setting colder e See Installing the Refrigerator e This indicates that there is a good seal on the freezer door drawer If the freezer door drawer does not automatically close after popping open then see the Problem Door drawer does not close by itself above GE Service Protection Plus GE a name recognized worldwide for quality and dependability offers you Service Protection Plus comprehensive protection on all your appliances No Matter What Brand i o Matter What Bran We ll Cover Any Appliance E EI Anywhere Anytime e All brands covered e Unlimited service calls e All parts and labor costs included e No out of pocket expenses e No hidden deductibles e One 800 number to call You will be completely satisfied with our service protection or you may request your money back on the remaining value of your contract No questions asked It s that simple Protect your refrigerator dishwasher washer and dryer range TV VCR and much more any brand Plus there s no extra charge for emergency service and low monthly financing is available Even icemaker coverage and food spoilage protection is offered You can rest easy knowing that all your valuable household prod
5. MCL Average Concentration Average Maximum Average Minimum Reductio Tested using a flow rate of 0 5 gpm pressure of 60 psig pH of 7 5 0 5 temp of 68 5 F 20 3 C Measurement in Particles ml Particles used were 0 5 1 microns NTU Nephelometric Turbidity units Operating Specifications E Capacity certified for up to 750 gallons 2 838 1 up to six months E Pressure requirement 40 120 psi 2 8 8 2 bar E Temperature 33 100 F 0 6 38 C E Flow rate 0 5 gpm 1 9 Ipm General Installation Operation Maintenance Requirements E Flush new cartridge at full flow for 3 minutes to purge out trapped air E Replace cartridge when flow becomes too slow Special Notices E Installation instructions parts and service availability and standard warranty are included with the product when shipped This drinking water system must be maintained according to manufacturer s instructions including replacement of filter cartridges E Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts E The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water E Check for compliance with the state and local laws and regulations E Note that while the testing was performed under
6. 1 Year TERMS AND CONDITIONS 1 This warranty applies only for single family domestic use in Canada when the Refrigerator has been properly installed according to the instructions supplied by Camco and is connected to an adequate and proper utility service Damage due to abuse accident commercial use and alteration or defacing of the serial plate cancels all obligations of this warranty Service during this warranty period must be performed by an Authorized Camco Service Agent Neither Camco nor the Dealer is liable for any claims or damages resulting from failure of the Refrigerator or from service delays beyond their reasonable control To obtain warranty service purchaser must present the original Bill of Sale Components repaired or replaced are warranted through the remainder of the original warranty period only This warranty is in addition to any statutory warranty IMPORTANT WHAT IS NOT COVERED e Owner is responsible to pay for service calls related to product installation and or teaching how to use the product e Damage to finish must be reported within 48 hours following the delivery of the appliance e Improper installation proper installation includes adequate air circulation to the refrigeration system adequate electrical plumbing and other connecting facilities e Replacement of house fuses or resetting of circuit breakers e Replacement of light bulbs e Damage to pr
7. The bulbs are located at the top of the refrigerator compartment behind the controls To remove the light shield grasp the shield at the back and pull out to release the tabs at the back Rotate the shield down and then forward to release the tabs at the front suonaonysuy Guyesadg of the shield Freezer Light A C A UTI 0 N 7 After replacing with an appliance bulb Light bulbs may be hot of the same or lower wattage replace the shield 5 Plug the refrigerator back in 7 Unplug the refrigerator The bulb is located at the top of the freezer inside a light shield To remove the shield grasp the shield at the back and pull out to release the tabs at the back Appearance may vary Rotate the shield down and then forward to release the tabs at the front of the shield A 2 Q 3 A S S a sdij Gunooysajqnosy pioddns sauinsuog 15 Installation Instructions Refrigerator Models 20 and 22 Questions Call 800 GE CARES 800 432 2737 or Visit our Website at GEAppliances com In Canada call 1 800 361 3400 or Visit our Website at geappliances ca BEFORE YOU BEGIN Read these instructions completely and carefully be IMPORTANT Save these instructions for local inspector s use bd IMPORTANT Observe all governing codes and ordinances e Note to Installer Be sure to leave these instructions with the Consumer e Note to Consumer Keep these instructions f
8. freezer basket rests on a frame inside the freezer drawer Lift the basket up at the back To remove the half width basket Pull the basket out to the stop location Lift the basket up at the front to release it from the slides 6 Lift the back up and out of the slide To remove the deep full width baskets on freezer door models the shallow full width basket and the full width wire shelf 7 Pull the basket shelf out to the stop location Lift the front up and over the stop location To remove the shelf above the ice bin 7 Pull the shelf straight out GEAppliances com fullwidth wire shelf A shelf above the ice storage bin Lift the front up and lift the entire basket up and out of the drawer When replacing the basket make sure that the wire tabs and wire hooks on the sides of the basket go into the slots in the sides of the basket frame NOTE Always be sure to fully close this basket You will know it is fully closed when you feel it click into place Lift the basket shelf up and out 11 suo n nysuj ajes suon nnsuj Guyesadg 2 2 q Q 3 A S 5 a sdij Gurooysajqnosy pioddngs sauinsuoy Power Switch Safety Instructions Green Power Light Feeler Arm Operating Instructions Icemaker A S S S S S amp 2 Ice Bin To reach the power switch Troubleshooting Tips Consumer Support 12 About
9. or absences remove food and unplug the refrigerator Move the freezer control to the 0 off position and clean the interior with a baking soda solution of one tablespoon 15 ml of baking soda to one quart 1 liter of water Leave the doors open Operating Instructions Set the icemaker power switch to the O off position and shut off the water supply to the refrigerator Preparing to Move Secure all loose items such as base grille shelves and drawers by taping them securely in place to prevent damage S S S S S amp 2 Troubleshooting Tips Consumer Support 14 Pull the refrigerator straight out and return When pushing the refrigerator back make sure you don t roll over the power cord or icemaker supply line on some models If the temperature can drop below freezing have a qualified servicer drain the water supply system on some models to prevent serious property damage due to flooding Be sure the refrigerator stays in an upright position during moving Replacing the li ght bulbs GEAppliances com N SSS SSS SSS SSS T Turning the control to the 0 off position does not remove power to the light circuit lt gt Ea Refrigerator Lights z A C A UTIO N After replacing with an appliance bulb z Light bulbs may be hot of the same or lower wattage replace S D the shield Plug the refrigerator back in 7 Unplug the refrigerator
10. screws Move the plastic hinge hole thimble to the opposite hole Install the door stop on the left side F Remove the insert at the top left side of the base grille and install it on the right side Bottom of Freezer Door Bottom of Freezer Door Right Side Left Side G Replace the base grille by aligning the prongs on the back of the grille with the holes in the cabinet Push forward until the grille snaps into place 26 Installation Instructions INSTALL CENTER HINGE 9 INSTALL CENTER HINGE PIN A Transfer the plug button and screws in A Install the center hinge pin the hinge holes on the left side to the NOTE On models with a freezer door right side be sure to put the washer between the top of the freezer door and the bottom J of the center hinge 2e o Freezer Door Models Freezer Drawer Models TRANSFER REFRIGERATOR DOOR STOP Remove the door stop on right side of the bottom of the refrigerator door by removing the two screws Move the plastic hinge hole thimble to the opposite hole Install the door stop on the left side making sure to line up the screw holes in the door stop with the holes in the bottom of the door HANG THE FREEZER DOOR freezer door models Lower the freezer door onto the bottom hinge pin then shut the door making sure to align the door with the cabinet Make sure the gasket on the door is flush against the cabinet Bottom of Bo
11. that a properly grounded A d have become frayed or otherwise damaged Do not S Where a standard 2 prong wall outlet is use a cord that shows cracks or abrasion damage S encountered it is your personal responsibility and along its length or at either end 3 S y USE OF ADAP TER P LUGS Adapter plugs not permitted in Canada I Because of potential safety hazards under certain conditions we strongly recommend against the use of an adapter plug However if you must use an adapter where local If the adapter ground terminal breaks DO NOT USE codes permit a temporary connection may be made the refrigerator until a proper ground has been to a properly grounded 2 prong wall outlet by use established of a UL listed adapter available at most local hardware stores Installation Instructions Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the The larger slot in the adapter must be aligned with cover screw is metal and not insulated and the wall the larger slot in the wall outlet to provide proper outlet is grounded through the house wiring You should polarity in the connection of the power cord have the circuit checked by a qualified electrician to make sure the outlet is properly grounded When disconnecting the power cord from the adapter always hold the adapter in place with one hand while pulling the power cord plug with the other hand If this is not done the adapter grou
12. the automatic icemaker Automatic Icemaker on some models The icemaker will produce seven cubes per cycle approximately 100 130 cubes in a 24 hour period depending on freezer compartment temperature room temperature number of door openings and other use conditions See below for how to access ice and reach the power switch If the refrigerator is operated before the water connection is made to the icemaker set the power switch in the 0 off position When the refrigerator has been connected to the water supply set the power switch to the I on position The icemaker will fill with water when it cools to 15 F 10 C A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes You will hear a buzzing sound each time the icemaker fills with water Accessing Ice and Reaching the Power Switch To reach the icemaker power switch pull the shelf above the ice bin straight out Always be sure to replace the shelf To access ice simply pull the bin forward Icemaker Accessory Kit If your refrigerator did not come already equipped with an automatic icemaker an icemaker accessory kit is available at extra cost A newly installed refrigerator may take 12 to 24 hours to begin making ice Throw away the first few batches of ice to allow the water line to clear Be sure nothing interferes with the sweep of the feeler arm When the bin fills to the level of the feeler arm the icemake
13. the tubing into the shutoff valve and tighten compression nut until it is hand tight then tighten one additional turn with a wrench Overtightening may cause leaks Saddle Type Shutoff Valve Compression Nut SmartConnect 5 Tubing Outlet Valve Ferrule sleeve NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber FLUSH OUT THE TUBING Turn the main water supply on and flush out the tubing until the water is clear Shut the water off at the water valve after about one quart 1 liter of water has been flushed through the tubing To complete the installation of the refrigerator go back to Step 1 in Installing the Refrigerator Nor mal oper ating sounds GEAppliances com Newer refrigerators sound different from older refrigerators Modern refrigerators have more features and use newer technology Do you hear what I hear These sounds are normal HUMMM WHIR WHOOSH 4 The new high efficiency compressor may run faster and longer than your old refrigerator and you may hear a high pitched hum or pulsating sound while it is operating suoyanysuy ajes You may hear the fans spinning at high speeds This happens when the refrigerator is first plugged in when the doors are You may hear a whooshing sound when the doors close This is opened frequently or when a large
14. 1 4 hole may result in reduced ice production or smaller cubes Installation Instructions INSTALLING THE WATER LINE cont 4 FASTEN THE SHUTOFF VALVE CONNECT THE TUBING Fasten the shutoff valve to the cold water pipe with the pipe clamp Pipe aL Saddle Type Shutoff Valve T Vertical Cold Water Pipe NOTE Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to Saddle valves are illegal and use is not permitted in Massachusetts Consult with your licensed plumber 5 TIGHTEN THE PIPE CLAMP Tighten the clamp screws until the sealing washer begins to swell NOTE Do not overtighten or you may crush the tubing Pipe Clamp Inlet End Clamp ROUTE THE TUBING Route the tubing between the cold water line and the refrigerator Route the tubing through a hole drilled in the wall or floor behind the refrigerator or adjacent base cabinet as close to the wall as possible NOTE Be sure there is sufficient extra tubing about 8 2 4 m coiled into 3 turns of about 10 25 cm diameter to allow the refrigerator to move out from the wall after installation TO THE VALVE Place the compression nut and ferrule sleeve for copper tubing onto the end of the tubing and connect it to the shutoff valve Make sure the tubing is fully inserted into the valve Tighten the compression nut securely For plastic tubing from a GE SmartConnect Refrigerator Tubing kit insert the molded end of
15. 18P002 49 60282 05 03 JR Safety Instructions Operating Instructions Y S S S S S amp 2 Troubleshooting Tips Consumer Support IMPORTANT SAFETY INFORMATION READ ALL INSTRUCTIONS BEFORE USING A WARNING Use this appliance only for its intended purpose as described in this Owner s Manual wl lt 7x SAFETY PRECAUTIONS T N When using electrical appliances basic safety precautions should be followed including the following This refrigerator must be properly installed In refrigerators with automatic icemakers and located in accordance with the Installation avoid contact with the moving parts of the Instructions before it is used ejector mechanism or with the heating element that releases the cubes Do not place fingers or hands on the automatic icemaking mechanism while the refrigerator is plugged in Do not allow children to climb stand or hang on the shelves in the refrigerator They could damage the refrigerator and seriously injure themselves Unplug the refrigerator before cleaning and A making repairs Do not touch the cold surfaces in the freezer 8 rep compartment when hands are damp or wet NOTE We strongly recommend that any servicing be Skin may stick to these extremely cold surfaces performed by a qualified individual Do not store or use gasoline or other flammable Setting either or both controls to 0 off does vapors and liquids in the vicinity of this or any n
16. Bottom Freezer igerators Refr GEAppliances com Safety Instructions 2 4 Operating Instructions Additional Features 9 Automatic Icemaker 12 Controlin Sein Es ale ees 5 6 Crispers and Pans 10 Freezer 8S ea ces ee BN 11 Shelves and Bins 8 9 Water Filter 0 0 0 000 7 Care and Cleaning 13 15 Installation Instructions Installing the Refrigerator 17 21 Installing the Water Line 30 32 Preparing to Install the Refrigerator 16 Removing and Replacing the Freezer Drawer 22 23 Reversing the Door Swing 24 29 Troubleshooting Tips 33 34 Normal Operating Sounds 33 Consumer Support Consumer Support Back Cover Performance Data Sheet 39 Product Registration 35 36 Warranty for Canadian CHSLOMEES 6 Siping 8 Mayon des 37 Warranty for U S Customers 38 Write the model and serial numbers here Model Serial Find these numbers on a label on the right side near the top of the refrigerator compartment Owner s Manual and Installation Instructions Models 20 and 22 Cong lateur inf rieur R frig rateurs Manuel d utilisation et d installation La section fran aise commence a la page 41 Congelador inferior Refrigeradores Manual del peppa y instalaci n La secci n en espa ol empieza en la p gina 79 3828JL8012A 197D46
17. MOVE THE LEVELING LEGS if needed If after removing the freezer drawer and refrigerator door the refrigerator will still not fit through a doorway the leveling leg brackets can be removed A Remove the base grille by grasping it at the bottom and pulling it straight out Remove both brackets with a 3 8 hex head driver Installation Instructions REPLACING THE FREEZER DRAWER on some models Two people may be required to complete 1 ATTACH AND SECURE THE this procedure DRAWER FRONT TO THE SLIDES cont E Replace the Phillips head screws on both 1 ATTACH AND SECURE THE rail assemblies DRAWER FRONT TO THE SLIDES A Pull out the rail assemblies to the full length on each side of the cabinet HI LS Locate the slots on the inside of the rail assemblies near the back 2 REPLACE THE FREEZER BASKET Replace the lower freezer basket by lowering it into the frame Rail assembly Insert the hooks at the back of the drawer railings into the slots on the rail assemblies D Lower the front of the drawer making sure the tabs on the sides of the railings fit into the front slots in the rail assemblies 23 Installation Instructions REVERSING THE DOOR SWING IMPORTANT NOTES When reversing the door swing e Read the instructions all the way through before starting e Handle parts carefully to avoid scratching paint e Set screws down by their related parts to avoid using the
18. OOR freezer door models A Remove the tape and tilt the door away from the cabinet Lift the door off the bottom hinge pin NOTE There is a plastic washer between the hinge and the top of the freezer door Do not lose Set the door on a non scratching surface with the inside up 4 REMOVE CENTER HINGE Using an adjustable wrench and Phillips head screwdriver remove the bolts and screws securing the center hinge to the cabinet Set hinge bolts screws washer on freezer door models and hinge pin aside On models with a freezer drawer skip to Step 7 5 TRANSFER BOTTOM HINGE BRACKET freezer door models A Remove the base grille by grasping it at the bottom and pulling it straight out Using a 3 8 socket driver remove the screws securing the bottom hinge bracket to the cabinet Using an adjustable wrench remove the hinge pin and washer s from the right side of the bracket and install on the left D Using a 3 8 socket driver remove the leveling leg bracket from the bottom left side of the cabinet and install it on the right side Right Side Installation Instructions REVERSING THE DOOR SWING cont 5 TRANSFER BOTTOM HINGE 6 TRANSFER FREEZER DOOR STOP BRACKET freezer door models cont freezer door models E Install the bottom hinge bracket on the A Remove the door stop on right side of the left side of the cabinet bottom of the freezer door by removing the two
19. a solution about a tablespoon 15 ml of baking soda to a quart 1 liter of water This both cleans and neutralizes odors Rinse and wipe dry GEAppliances com The stainless steel panels and door handles Stainless steel on some models can be cleaned with a commercially available stainless steel cleaner A spray on stainless steel cleaner works best Do not use appliance wax or polish on the stainless steel After cleaning the door gaskets apply a thin layer of petroleum jelly to the door gaskets at the hinge side This helps keep the gaskets from sticking and bending out of shape Avoid cleaning cold glass shelves with hot water because the extreme temperature difference may cause them to break Handle glass shelves carefully Bumping tempered glass can cause it to shatter Do not wash any plastic refrigerator parts in the dishwasher 13 suoyaonysuy ajes suon nnsuj Guyesadg 2 2 q Q 3 A S 5 a sdij Gurooysajqnosy pioddns sauinsuog Care and cleaning of the refrigerator Behind the Refrigerator Be careful when moving the refrigerator away from the wall All types of floor coverings can be damaged particularly cushioned coverings and those with embossed surfaces Safety Instructions it to position by pushing it straight in Moving the refrigerator in a side direction may result in damage to the floor covering or refrigerator Preparing for Vacation For long vacations
20. amount of food is added to due to pressure equalizing within the refrigerator the refrigerator or freezer compartments The fans are helping to maintain the correct temperatures The fans change speeds in order to provide optimal cooling and energy savings CLICKS POPS WATER SOUNDS CRACKS and SNAPS You may hear cracking or popping sounds when the refrigerator is first plugged in This happens as the refrigerator f cools to the correct temperature The flow of refrigerant through the freezer cooling coils may make a gurgling noise like boiling water suononysuy Guyesadg The freezer control will click when starting or stopping the f na compressor Water dropping on the defrost heater can cause a sizzling i buzzi d during the defrost cycle Defrost timer snapping in and out of the defrost cycle Pee EPOE AEA ee TEIE O A water dripping noise may occur during the defrost cycle as Expansion and contraction of cooling coils during and after ice melts from the evaporator and flows into the drain pan defrost can cause a cracking or popping sound f i Closing the door may cause a gurgling sound due to pressure On models with an icemaker after an icemaking cycle you equalization may hear the ice cubes dropping into the ice bucket A 2 Q 3 A S 2 S a Before you call for service S Troubleshooting Tips D Save time and money Review the charts on the following pages first and
21. ation and prompt service under the terms of your warranty should the need arise You may also mail in the pre printed registration card included in the packing material In Canada geappliances ca Printed in Mexico
22. da or two wine water bottles lengthwise It can be removed for cleaning GEAppliances com The snugger helps prevent tipping spilling or sliding of small items stored on the door shelf Grip the finger hold near the rear of the snugger and move it to fit your needs To remove slide the rack out to the stop position lift the rack up and past the stop position and lift it out suoyaonysuy ajes suononysuy Guyesadg A 2 q Q 3 A S 3 a sdij Gunooysajqnosy pioddns sauinsuoy Safety Instructions Operating Instructions S S S 3 S S amp Troubleshooting Tips Consumer Support 10 About the crispers and pans Not all features are on all models Fruit and Vegetable Crisper Excess water that may accumulate in the bottom of the drawers or under the drawers should be wiped dry Adjustable Humidity Crisper on some models Slide the control all the way to the HIGH setting to provide high humidity recommended for most vegetables Snack Pan on some models This pan can be moved to the most useful location for your family s needs Slide the control all the way to the LOW setting to provide lower humidity levels recommended for most fruits To remove slide the pan out to the stop position lift the pan up and past the stop position and lift it
23. ffect You can purchase it on line anytime or call 800 626 2224 during normal business hours GE Consumer Home Services will still be there after your warranty expires In Canada call 1 888 261 2133 Parts and Accessories In the U S GEAppliances com Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes VISA MasterCard and Discover cards are accepted Order on line today 24 hours every day or by phone at 800 626 2002 during normal business hours Instructions contained in this manual cover procedures to be performed by any user Other servicing generally should be referred to qualified service personnel Caution must be exercised since improper servicing may cause unsafe operation Customers in Canada should consult the yellow pages for the nearest Camco service center or call 1 888 261 3055 Contact Us In the U S GEAppliances com KoA If you are not satisfied with the service you receive from GE contact us on our Website with all the details including your phone number or write to General Manager Customer Relations GE Appliances Appliance Park Louisville KY 40225 In Canada geappliances ca or write to Director Consumer Relations Camco Inc Suite 310 1 Factory Lane Moncton N B E1C 9M3 Register Your Appliance In the U S GEAppliances com Register your new appliance ondine at your convenience Timely product registration will allow for enhanced communic
24. formance suoyanysuy ajes suonanysuy Guyesadg A 2 Q 3 A S 2 5 a sdij Gurooysajqnosy pioddns sauinsuoy About the controls with numbered settings 5 0 IS OFF 5 91S COLDEST ADJUST FREEZER ADJUST REFRIGERATOR NB NOTE The refrigerator is shipped with protective film covering the temperature controls If this film was not removed during installation remove it now Safety Instructions Initially set the refrigerator control at 5 and the freezer control at 5 and allow 24 hours for the temperature to stabilize Several adjustments may be required Adjust the controls one increment at a time and allow 24 hours after each adjustment for the refrigerator to reach the temperature you have set Operating Instructions Setting either or both controls to 0 stops cooling in both the refrigerator and freezer compartments but does not shut off electrical power to the refrigerator Performance Air Flow System The Performance Air Flow System is designed to wall of the refrigerator and the Air Tunnel on the maximize temperature control in the refrigerator bottom portion of the freezer rear wall Placing and freezer compartments This unique special food in front of the louvers on these components feature consists of the Air Tower along the back will not affect performance A S S S 2 lt S amp 3 Troubleshooting Tips Consumer Support About the water filter on s
25. ging in the refrigerator make sure the icemaker power switch is set to the O off position See the grounding information attached to the power cord 4 PUT THE REFRIGERATOR IN PLACE Move the refrigerator to its final location Installation Instructions 5 ATTACH REFRIGERATOR 5 ATTACH REFRIGERATOR DOOR HANDLE DOOR HANDLE cont A Look for an arrow label on the front of Holding the handle with both hands the handle press it firmly against the front of the If the door mounting screws are located door and slide the handle down This on the left side of the door hold the may require some force handle so the arrow points to the right arrow is at the top of the handle If the door mounting screws are located on the right side of the door hold the handle so the arrow points to the left arrow is at the bottom of the handle ee f Screws mounted Keyhole slots Door on door on back of handle handle on right side L Y ee Align keyhole slots on the top and bottom of the back of the handle with the screws mounted on the front of the door Press the handle against the door front making sure that the screws go into the keyhole slots 19 Installation Instructions INSTALLING THE REFRIGERATOR cont 6 ATTACH FREEZER DOOR HANDLE A Look for an arrow label on the front of the handle Hold the handle so that the arrow is pointing to the left Al
26. iances com Have a question or need assistance with your appliance Try the GE Appliances Website 24 hours a day any day of the year For greater convenience and faster service you can now download Owner s Manuals order parts catalogs or even schedule service on line You can also Ask Our Team of Experts your questions and so much more In Canada geappliances ca Schedule Service In the U S GEAppliances com Expert GE repair service is only one step away from your door Get on line and schedule your service at your convenience 24 hours any day of the year Or call 800 GE CARES 800 432 2737 during normal business hours In Canada call 1 800 361 3400 Real Life Design Studio In the U S GEAppliances com GE supports the Universal Design concept products services and environments that can be used by people of all ages sizes and capabilities We recognize the need to design for a wide range of physical and mental abilities and impairments For details of GE s Universal Design applications including kitchen design ideas for people with disabilities check out our Website today For the hearing impaired please call 800 TDD GEAC 800 833 4322 In Canada contact Manager Consumer Relations Camco Inc Suite 310 1 Factory Lane Moncton N B E1C 9M3 Extended Warranties In the U s GEAppliances com Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still in e
27. ign keyhole slots on the right and left sides of the back of the handle with the screws mounted on the front of the door drawer Press the handle against the door drawer front making sure that the screws go into the keyhole slots Holding the handle with both hands press it firmly against the front of the door and slide the handle to the left Screws mounted on door Keyhole slots on back of handle 20 LEVEL THE REFRIGERATOR The leveling legs have 3 purposes 1 Leveling legs adjust so the door closes easily when opened about halfway Front of the refrigerator should be 1 4 6 mm higher than the rear of the refrigerator 2 Leveling legs adjust so the refrigerator is firmly positioned on the floor and does not wobble 3 Leveling legs serve as a stabilizing brake to hold the refrigerator securely in position during operation and cleaning A Turn the leveling legs clockwise to raise the refrigerator counterclockwise to lower it PS PA Se A CAUTION To avoia possible personal injury or property damage the leveling feet must be firmly touching the floor Install the base grille by aligning the prongs on the back of the grille with the holes in the cabinet Push forward until the grille snaps into place a Installation Instructions SET THE CONTROLS 9 START THE ICEMAKER Set the controls to the recommended icemaker models setting Set the icemaker power switch to the I on positi
28. l Number Mr Ms Mrs Miss L First Last Name Name Street Address l l l Apt l E mail Address Zip City State Code l ee l l Month Day Year Number l Please provide your e mail address to receive via e mail discounts special offers and other important communications from GE Appliances GEA E Check here if you do not want to receive communications from GEA s carefully selected partners E Appliances PP FAILURE TO COMPLETE AND RETURN THIS CARD DOES NOT DIMINISH YOUR GE Consumer Products WARRANTY RIGHTS General Electric Company Louisville Kentucky www GEAppliances com 36 For information about GEA s privacy and data usage policy go to www GEAppliances com and click on Privacy Policy or call 800 626 2224 oper Cuthere CUSTOMER WARRANTY for customers in Canada Your refrigerator is warranted to be free of defects in material and workmanship e DA x as NS 2 S ERS 56 6 a a What is covered ie re at 2 S From Date of Sale gt oy rags Compressor Five 5 Years ne X Sealed System including evaporator condenser tubing and refrigerant Five 5 Years gt we me or gt E LO NOLS RR PA All Other Parts One 1 Year nN es x How Long Warranted Parts Repair or Replace at Camco s Option Five 5 Years Five 5 Years Five 5 Years Five 5 Years One 1 Year One
29. ll for service Possible Causes Normal when refrigerator is first plugged in What To Do e Wait 24 hours for the refrigerator to completely cool down Often occurs when large amounts of food are placed in refrigerator e This is normal Door left open e Check to see if package is holding door open Hot weather or frequent door openings e This is normal Temperature control set at the coldest setting e See About the controls Grille and condenser need cleaning Temperature controls not set cold enough e See Care and cleaning e See About the controls Warm weather or frequent door openings e Set the temperature control one step colder See About the controls Door left open Door left open e Check to see if package is holding door open e Check to see if package is holding door open Too frequent or too long door openings Food transmitting odor taste to ice cubes e Wrap foods well Interior of refrigerator needs cleaning Door left open Freezer control not set cold enough Foods transmitting odor to refrigerator e See Care and cleaning e Check to see if package is holding door open e See About the controls e Foods with strong odors should be tightly wrapped Keep an open box of baking soda in the refrigerator replace every three months Interior needs cleaning Not unusual during periods of high humidity
30. llow ice cubes This water line installation is not warranted by the refrigerator or icemaker manufacturer Follow these instructions carefully to minimize the risk of expensive water damage Water hammer water banging in the pipes in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator To prevent burns and product damage do not hook up the water line to the hot water line If you use your refrigerator before connecting the water line make sure the icemaker power switch is in the O off position Do not install the icemaker tubing in areas where temperatures fall below freezing When using any electrical device such as a power drill during installation be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock or is battery powered All installations must be in accordance with local plumbing code requirements 30 WHAT YOU WILL NEED e Copper or GE SmartConnect Refrigerator Tubing kit 1 4 outer diameter to connect the refrigerator to the water supply If using copper be sure both ends of the tubing are cut square To determine how much tubing you need measure the distance from the water valve on the back of the refrigerator to the water supply pipe Then add 8 2 4 m Be sure there is sufficient extra tubing about 8
31. lls from dripping to lower shelves To replace Place the rear shelf tabs just in front of the central notches on the shelf frame Slide the shelf in until the central tabs To remove are slightly behind the front bar 7 Remove all items from shelf Lower the shelf into place until it is 2 Slide the shelf out until it stops horizontal and slide the shelf in Troubleshooting Tips Consumer Support Co Lift the front edge of the shelf until the central tabs are above the front bar Continue pulling the shelf forward until it can be removed Make sure that the shelf sits flat after reinstallation and doesn t move freely from side to side Make sure you push the shelves all the way in before you close the door Not all features are on all models Finger hold Snugger Adjustable Bins on the Door Adjustable bins can easily be carried from refrigerator to work area To remove Lift bin straight up then pull out To replace or relocate Engage the bin in the molded supports of the door and push in Bin will lock in place Non Adjustable Shelves on the Door To remove Lift the shelf straight up then pull out To replace Engage the shelf in the molded supports on the door and push down It will lock in place About the additional features Not all features are on all models Shelf Saver Rack on some models Slide out beverage rack holds twelve cans of so
32. m in the wrong places e Provide a non scratching work surface for the doors IMPORTANT Once you begin do not move the cabinet until door swing reversal is completed These instructions are for changing the hinges from the right side to the left side if you ever want to change the hinges back to the right side follow these same instructions and reverse all references to left and right Unplug the refrigerator from its electrical outlet Empty all door shelves including the dairy compartment TOOLS YOU WILL NEED Adjustable Wrench Masking Tape SSCS CO 3 8 Head Socket Driver a 6 point socket is recommended qGExc Putty Knife or Thin blade Screwdriver 1 REMOVE THE REFRIGERATOR DOOR A Tape the door shut with masking tape Remove the hinge cover on top of the refrigerator door by squeezing it and pulling it up Using an adjustable wrench remove the bolts securing the top hinge to the cabinet Then lift the hinge straight up to free the hinge pin from the socket in the top of the door Top Hinge D Remove the tape and tilt the door away from the cabinet Lift the door off the center hinge pin E Set the door on a non scratching surface with the inside up Installation Instructions 2 REMOVE THE CENTER HINGE PIN A On models with a freezer door tape the door shut with masking tape Using an adjustable wrench remove the center hinge pin 3 REMOVE THE FREEZER D
33. nd terminal is very likely to break with repeated use Troubleshooting Tips J READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY N SAVE THESE INSTRUCTIONS gt A N Pd S S About the controls with temperature settings for other models see next page GEAppliances com ADJUST FREEZER TEMP ADJUST REFRIGERATOR TEMP SS COLDER WARMER 0 F IS RECOMMENDED SET COLDER WARMER i ee SET 37 F IS RECOMMENDED NOTE The refrigerator is shipped with protective film covering the temperature controls If this film was not removed during installation remove it now The temperature controls are preset in the factory at 37 F for the refrigerator compartment and 0 F for the freezer compartment Allow 24 hours for the temperature to stabilize to the preset recommended settings The temperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer The actual temperature may vary slightly from the SET temperature based on usage and operating environment Setting either or both controls to OFF stops cooling in both the freezer and refrigerator compartments but does not shut off electrical power to the refrigerator Changing the Temperature To change the temperature press and release the WARMER or COLDER pad The SET light will come on and the display will show the set temperature To change the temperature tap either the WARMER or COLDER pad until
34. nding type plug and outlet and that the electrical rating of the cord be 15 amperes minimum and 120 volts suoyanysuy ajes suoyonysuy Guyesadg A gt q Q 3 A S S a sdij Gurooysajqnosy pioddns sauinsuoy IMPORTANT SAFETY INFORMATION obligation to have it replaced with a properly grounded 3 prong wall outlet When moving the refrigerator away from the wall be careful not to roll over or damage the The refrigerator should always be plugged into its power cord own individual electrical outlet which has a voltage rating that matches the rating plate a READ ALL INSTRUCTIONS BEFORE USING S 2 A WARNING N S gt m HOW TO CONNECT ELECTRICITY A a gt Do not under any circumstances cut or remove the third ground prong from the power cord 9 For personal safety this appliance must be properly grounded The power cord of this appliance is equipped This provides the best performance and also with a 3 prong grounding plug which mates prevents overloading house wiring circuits which 2 with a standard 3 prong grounding wall outlet to could cause a fire hazard from overheated wires minimize the possibility of electric shock hazard iota dhis appliance Never Wiig your ee sth ee T the power cord Always grip plug firmly and pu Have the wall outlet and circuit checked by a straight out from the outlet 77 A zi S a e A A Repair or replace immediately all power cords
35. ntial damage caused by possible defects with this appliance Damage caused after delivery This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA In Alaska the warranty excludes the cost of shipping or service calls to your home Some states do not allow the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state To know what your legal rights are consult your local or state consumer affairs office or your state s Attorney General 38 Warrantor General Electric Company Louisville KY 40225 Performance Data Sheet SmartWater Filtration System GSWF Cartridge This system has been tested according to NSF ANSI 42 53 for reduction of the substances listed below The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system as specified in NSF ANSI 42 53 100 safety factors built in for unmetered usage Ne tat MCL Average Concentration Reduction omone d Treo gt Particulate 1 845 mg L 2 0 mg L 10 lt 0 05 mg L 0 05 mg L gt 97 29 96 43 gt 50 143 333 mL at least 10 000 particles mL 29 83 mL 140 mL 99 98 99 91 Standard No 53 Health Effects Influent Min Required
36. oduct caused by accident fire floods or acts of God e Loss of food due to spoilage e Proper use and care of product as listed in the owner s manual proper setting of controls e WARRANTOR IS NOT RESPONSIBLE FOR CONSEQUENTIAL DAMAGES Keep this warranty and your bill of sale as proof of original purchase and purchase date Camco Service is available coast to coast If further help is needed concerning this warranty contact Manager Consumer Relations Camco Inc Consumer Service 1 Factory Lane Suite 310 Moncton New Brunswick E1C 9M3 Staple your receipt here Proof of the original purchase date is needed to obtain service under the warranty Safety Instructions Operating Instructions Y S S S S S amp 2 Troubleshooting Tips Consumer Support Refr iger ator Warr anty For customers in the United States All warranty service provided by our Factory Service Centers Staple your receipt here all or an authorized Customer Care technician To schedule service Proof of the original purchase on line 24 hours a day visit us at GEAppliances com or call date is needed to obtain service 800 GE CARES 800 432 2737 under the warranty For The Period Of GE Will Replace One Year Any part of the refrigerator which fails due to a defect in materials or workmanship From the date of the During this full one year warranty GE will also provide free of cha
37. ome models Water Filter Cartridge The water filter cartridge is located in the back upper right corner of the refrigerator compartment When to Replace the Filter The filter cartridge should be replaced every Six months or earlier if you notice your ice cubes becoming smaller Installing the Filter Cartridge Ifyou are replacing the cartridge first remove the old one Open the cartridge cover by pressing in on the tab at the front and pulling down Remove the cartridge by slowly rotating it counterclockwise A small amount of water may drip down A CA U TI ON If air has been trapped in the system the filter cartridge may be ejected as it is removed Use caution when removing Mark you calender or apply the month and year sticker to remind you to replace the filter cartridge in six months Remove the protective foil from the end of the cartridge Lining up the arrow on the cartridge and the cartridge holder slowly rotate the cartridge clockwise until it stops When the cartridge is properly installed you will feel it click as it locks into place The blade on the end of the cartridge should be positioned vertically Do not overtighten 6 Close the cartridge cover GEAppliances com Filter Bypass Plug You must use the filter bypass plug when a replacement filter cartridge is not available The icemaker will not operate without the filter or filter bypass plug Replacement Filters To orde
38. on The icemaker will not begin to operate until it reaches its 5 5 operating temperature of 15 F 9 C or below It will then begin operation automatically It will take 2 3 days to fill the ice bin RECOMMENDED CONTROL SETTINGS 0 F IS RECOMMENDED 37 F IS RECOMMENDED Power switch NOTE In lower water pressure conditions the water valve may turn on up to 3 times to deliver enough water to the icemaker 21 Installation Instructions REMOVING THE FREEZER DRAWER on some models The freezer drawer can be removed if needed to fit through tight areas Read these instructions completely and carefully 1 REMOVE THE BASKET A Open the freezer drawer until it stops The freezer basket rests on a frame inside the freezer drawer Lift the basket up at the back Lift the front up and lift the entire basket up and out of the drawer 2 REMOVE THE DRAWER FRONT FROM THE SLIDES A Remove the Phillips head screw on each side of the railing DO NOT remove the hex head screws from the rail assemblies DO NOT remove hex head screws DO NOT remove hex head screws 2 REMOVE THE DRAWER FRONT FROM THE SLIDES cont Lift up on both sides of the freezer drawer handle to separate the drawer railings from the rail assemblies Set the drawer front on a non scratching surface D Push the rail assemblies back into locking position Rail Assembly Drawer Assembly B RE
39. or future reference e Skill level Installation of this appliance requires basic mechanical skills e Completion time Refrigerator Installation 20 minutes Water Line Installation 30 minutes e Proper installation is the responsibility of the installer e Product failure due to improper installation is not covered under the Warranty PREPARATION MOVING THE REFRIGERATOR INDOORS If the refrigerator will not fit through a doorway the refrigerator door and freezer drawer or door depending on model can be removed e To remove the refrigerator door see Step 1 in the Reversing the Door Swing section e To remove the freezer drawer see the Removing the Freezer Drawer section e To remove the freezer door see Steps 2 and 3 in the Reversing the Door Swing section 16 PREPARATION cont WATER SUPPLY TO THE ICEMAKER If the refrigerator has an icemaker it will have to be connected to a cold water line A GE water supply kit containing tubing shutoff valve fittings and instructions is available at extra cost from your dealer by visiting our Website at GEAppliances com in Canada at geappliances ca or from Parts and Accessories 800 626 2002 In Canada 1 888 261 3055 TOOLS YOU MAY NEED ECO 3 8 Head Socket Driver a 6 point socket is recommended 65 Adjustable Wrench CO 1 4 Outer Diameter Compression Nut and Ferrule sleeve icemaker models only Phillips Head Screwdriver
40. ot remove power to the light circuit other appliance Do not refreeze frozen foods which have Keep fingers out of the pinch point areas thawed completely clearances between the doors and between the doors and cabinet are necessarily small Be careful closing doors when children are in the area GEAppliances com A DANGER RISK OF CHILD ENTRAPMENT PROPER DISPOSAL OF THE REFRIGERATOR Child entrapment and suffocation are not problems of the past Junked or abandoned refrigerators are still dangerous even if they will sit for just a few days If you are getting rid of your old refrigerator please follow the instructions below to help prevent accidents Before You Throw Away Your Old Refrigerator or Freezer Take off the doors Leave the shelves in place so that children may not easily climb inside USE OF EXTENSION CORDS i the use of an extension cord Refrigerants All refrigeration products contain refrigerants which under federal law must be removed prior to product disposal If you are getting rid of an old refrigeration product check with the company handling the disposal about what to do Because of potential safety hazards under certain conditions we strongly recommend against However if you must use an extension cord it is absolutely necessary that it be a UL listed in the United States or a CSA certified in Canada 3 wire grounding type appliance extension cord having a grou
41. out Adjustable Temperature Deli Pan on some models When the pan is placed in the 7th slot from the bottom of the track and the lever is set at COLDEST air from the freezer is forced around the pan to keep it very cold You can mowe the pan to any location if you don t want the extra cold storage Crisper Removal To Remove These drawers can be removed easily by lifting up slightly while pulling the drawer past the stop location The settings can be adjusted anywhere between cold and coldest When set at cold the pan will stay at the normal refrigerator temperature The coldest setting provides the coldest storage area When the door cannot be fully opened remove the drawer farthest from the door first Make sure the drawer closest to the door is fully closed There is a latch at the front of the center slide rail Push down on the latch and slide the center slide rail to which the drawer is attached away from the door Remove the drawer About the freezer Not all features are on all models Appearance may vary Ice Bin Freezer Shelves and Baskets Depending on your model your freezer may feature 7 A deep full width basket 2 A shallow full width basket 6 A half width basket Basket Shelf Removal To remove the deep full width basket on freezer drawer models Open the freezer drawer until it stops The
42. r additional filter cartridges in the United States visit our Website GEAppliances com or call GE Parts and Accessories 800 626 2002 Filter Model GSWF Suggested Retail Price 34 95 USD Customers in Canada should consult the yellow pages for the nearest Camco Service Center suoyonysuy ajes suonaonysuy Guyesadg A 2 Q 3 A S S a sdij Gurooysajqnosy pioddns sauinsuoy About the shelves and bins Not all features are on all models Rearranging the Shelves Shelves in the refrigerator compartment are adjustable Safety Instructions Refrigerator Compartment To remove 7 Tilt the shelf up at the front Lift the shelf up at the back and bring the shelf out Some models have wire shelves that can be adjusted in the same manner To replace p 7 While tilting the shelf up insert the top hook at the back of the shelf in a slot on the track Lower the front of the shelf until the bottom of the shelf locks into place Operating Instructions Spillproof Shelves on some models Spillproof shelves have special edges to help prevent spills from dripping to lower shelves To remove or replace the shelves see Rearranging the Shelves S S S S S amp 2 Slide Out Spillproof Shelf on some models The slide out spillproof shelf allows you to reach items stored behind others The special edges are designed to help prevent spi
43. r will stop producing ice It is normal for several cubes to be joined together If ice is not used frequently old ice cubes will become cloudy taste stale and shrink NOTE In homes with lower than average water pressure you may hear the icemaker cycle multiple times when making one batch of ice To access ice Check the back of the refrigerator for the specific icemaker kit needed for your model Care and cleaning of the refrigerator Cleaning the Outside The door handles and trim Clean with a cloth dampened with soapy water Dry with a soft cloth Do not use wax on the door handles and trim Keep the outside clean Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent Dry and polish with a clean soft cloth Do not wipe the refrigerator with a soiled dish cloth or wet towel These may leave a residue that can erode the paint Do not use scouring pads powdered cleaners bleach or cleaners containing bleach because these products can scratch and weaken the paint finish Cleaning the Inside To help prevent odors leave an open box of baking soda in the refrigerator and freezer compartments Unplug the refrigerator before cleaning If this is not practical wring excess moisture out of sponge or cloth when cleaning around switches lights or controls Use an appliance wax polish on the inside surface between the doors Use warm water and baking sod
44. rge all labor and in home original purchase service to replace the defective part Five Years Any part of the sealed refrigerating system the compressor condenser evaporator From the date of the and all connecting tubing which fails due to a defect in materials or workmanship original purchase During this full five year sealed refrigerating system warranty GE will also provide free of charge all labor and in home service to replace the defective part in the sealed refrigerating system Thirty Days Any part of the water filter cartridge which fails due to a defect in materials or workmanship From the original During this limited thirty day warranty GE will also provide free of charge a replacement water purchase date of the filter cartridge refrigerator What GE Will Not Cover Service trips to your home to teach you how to use Replacement of the water filter cartridge due to water the product pressure that is outside the specified operating range or Improper installation delivery or maintenance Failure of the product if it is abused misused or used for due to excessive sediment in the water supply Replacement of the light bulbs or water filter cartridge other than as noted above other than the intended purpose or used commercially Loss of food due to spoilage Replacement of house fuses or resetting of circuit breakers Damage to the product caused by accident fire floods or acts of God Incidental or conseque
45. s INSTALLING THE REFRIGERATOR cont 1 CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE cont A If you are using copper tubing place a compression nut and ferrule sleeve onto the end of the tubing coming from the house cold water supply If you are using the GE SmartConnect tubing the nuts are already assembled to the tubing If you are using copper tubing insert the end of the tubing into the refrigerator connection at the back of the refrigerator as far as possible While holding the tubing tighten the fitting If you are using GE SmartConnect tubing insert the molded end of the tubing into the refrigerator connection at the back of the refrigerator and tighten the compression nut until it is hand tight Then tighten one additional turn with a wrench Overtightening may cause leaks Fasten the tubing into the clamp provided to hold it in position You may need to pry open the clamp One of the illustrations below will look like the connection on your refrigerator 1 4 Copper Tubing Compression Nut Refrigerator Connection SmartConnect Tubing Tubing Clamp 1 4 Tubing Compression Nut X Ferrule sleeve s Refrigerator a Connection SmartConnect Tubing 2 TURN ON THE WATER SUPPLY icemaker models Turn the water on at the shutoff valve house water supply and check for any leaks 3 PLUG IN THE REFRIGERATOR On models with an icemaker before plug
46. standard laboratory conditions actual performance may vary Systems must be installed and operated in accordance with manufacturer s recommended procedures and guidelines System tested and certified by NSF International against Standard 42 for the reduction of chlorine taste and odor particulate Class I and Standard 53 for the reduction of cyst N S F lead Lindane Atrazine and turbidity Manufactured for General Electric Company Louisville KY 40225 39 State of California Department of Health Services Water Treatment Device Certificate Number 03 1559 Date Issued April 28 2003 Trademark Model Designation Replacement Elements GE GSWF GSWF Manufacturer General Electric Consumer Products The water treatment device s listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminants Microbiological Contaminants and Turbidity Inorganic Radiological Contaminants Cysts Asbestos Turbidity Lead Organic Contaminants Atrazine Lindane 2 4 D Rated Service Capacity 750 gal Rated Service Flow 0 5 gpm Conditions of Certification Do not use where water is microbiologically unsafe or with water of unknown quality except that systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts 40 Consumer Support GE Appliances Website In the U S GEAppl
47. the desired temperature is displayed Refrigerator temperatures can be adjusted between 34 F and 47 F and the freezer temperatures can be adjusted between 6 F and 8 F Once the desired temperature has been set the temperature display will return to the actual refrigerator and freezer temperatures after 5 seconds Several adjustments may be required Performance Air Flow System The Performance Air Flow System is designed to maximize temperature control in the refrigerator and freezer compartments This unique special feature consists of the Air Tower along the back Each time you adjust controls allow 24 hours for the refrigerator to reach the temperature you have set To turn the cooling system off tap the WARMER pad for either the refrigerator or the freezer until the display shows OFF To turn the unit back on press the COLDER pad for either the refrigerator or freezer The SET light will illuminate on the side you selected Then press the COLDER pad again on the side where the SET light is illuminated and it will go to the preset points of 0 F for the freezer and 37 F for the refrigerator Setting either or both controls to OFF stops cooling in both the freezer and refrigerator compartments but does not shut off electrical power to the refrigerator wall of the refrigerator and the Air Tunnel on the bottom portion of the freezer rear wall Placing food in front of the louvers on these components will not affect per
48. tings are preassembled to the tubing O e If your existing copper water line has a flared fitting at the end you will need an adapter available at plumbing supply stores to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting Do not cut formed end from GE SmartConnect Refrigerator tubing ka Shutoff valve to connect to the cold water line The shutoff valve should have a water inlet with a minimum inside diameter of 5 32 at the point of connection to the COLD WATER LINE Saddle type shutoff valves are included in many water supply kits Before purchasing make sure a saddle type valve complies with your local plumbing codes 31 1 SHUT OFF THE MAIN WATER SUPPLY Turn on the nearest faucet long enough to clear the line of water CHOOSE THE VALVE LOCATION Choose a location for the valve that is easily accessible It is best to connect into the side of a vertical water pipe When it is necessary to connect into a horizontal water pipe make the connection to the top or side rather than at the bottom to avoid drawing off any sediment from the water pipe I DRILL THE HOLE FOR THE VALVE Drill a 1 4 hole in the water pipe even if using a self piercing valve using a sharp bit Remove any burrs resulting from drilling the hole in the pipe Take care not to allow water to drain into the drill Failure to drill a
49. ttom of Refrigerator Door Refrigerator Door Right Side Left Side 27 Installation Instructions REVERSING THE DOOR SWING cont 11 TRANSFER REFRIGERATOR DOOR HANDLE TO RIGHT In order to correctly install the handle on the right side place a small piece of masking tape near the top of the handle before removing A Grasp the handle tightly with both hands and slide the handle up this may require some force The keyhole slots on the back of the handle allow the handle to separate from the mounting screws 11 TRANSFER REFRIGERATOR E DOOR HANDLE TO RIGHT cont Holding the handle so the masking tape is at the bottom align keyhole slots on the top and bottom of the back of the handle with the screws mounted on the front of the door Press the handle against the door front making sure that the screws go into the keyhole slots Grasping the handle with both hands press it firmly against the front of the door and slide the handle down This may require some force Screws mounted on door Keyhole slots on back of handle Keyhole slots Screws D Using an adjustable wrench remove the handle mounting screws Carefully pry off the logo badge and plug button Remove a layer of adhesive and backing to expose new adhesive Install logo badge and plug button on left side Install the handle mounting screws on the right side on back of handle mounted on door
50. ucts are protected against expensive repairs Place your confidence in GE and call us in the U S toll free at 800 626 2224 for more information All brands covered up to 20 years old in the continental U S Please place in envelope and mail to General Electric Company Warranty Registration Department P O Box 32150 Louisville KY 40232 2150 35 Consumer Product Ownership Registration Dear Customer Thank you for purchasing our product and thank you for placing your confidence in us We are proud to have you as a customer Follow these three steps to protect your new appliance investment Complete and mail your Consumer Product Ownership Registration today Have the peace of mind of knowing we can contact you in the unlikely event of a safety modification After mailing the Read your Owner s registration below Manual carefully store this document It will help you in a safe place It operate your new contains information you will need should you require service Our service number is 800 GE CARES 800 432 2737 appliance properly Model Number Serial Number Important If you did not get a registration card with your product detach and return the form below to ensure that your product is registered or register online at www GEAppliances com Model Number Seria
51. you may not need to call for service S Problem Possible Causes What To Do Refrigerator does not Refrigerator in defrost cycle e Wait about 30 minutes for defrost cycle to end ig operate Control in 0 off position e Move the control to a temperature setting Refrigerator is unplugged e Push the plug completely into the outlet gt The fuse is blown circuit e Replace fuse or reset the breaker 77 breaker is tripped S Vibration or rattling Leveling legs need adjusting e See Level the Refrigerator slight vibration 2 is normal 3S S Q 33 Problem Motor operates for long periods or cycles on and off frequently Modern refrigerators with more storage space and a larger freezer require more operating time They start and stop often to maintain even temperatures Safety Instructions Refrigerator or freezer compartment too warm Y S S S S 3 D NS S S N S Q Frost or ice crystals S on frozen food gt frost within package 2 is normal S Ice cubes have odorftaste v x Slow ice cube freezing N d Refrigerator has odor A 2 Moisture forms on outside of refrigerator 5 Moisture collects inside in humid weather air carries moisture into refrigerator when doors are opened Door drawer does not close by itself Freezer door drawer pops open when refrigerator door is closed Consumer Support 34 Before you ca

Continental Refrigerator 22 User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents