Charnwood Country 8B User's Manual
Contents
1. Overflow 7 Overflow Domestic Hot Water Draw Off Gravity Radiator Drain Cock Indirect Hot Water Cylinder High Limit Thermostat Low Limit Thermostat f Central Heating Flow Circulating Pump Central Heating Return Drain Cock at Lowest Point Injector Tee Fig 5 Typical Central Heating amp Hot Water System Using 3 Tappings Gravity Return 28mm Pipe Common Return to Boiler 28mm Pipe Central Heating Return Fig 6 Injector Tee Page 7 Country 8B WB _ 10 00 inches each side and 300mm 12 inches above the appliance should give sufficient air circulation If a wooden mantelpiece or beam is used in the fireplace it should be a minimum of 460mm 18 inches and preferably 600mm 24 inches from the appliance In some situations it may be necessary to shield the beam or mantelpiece to protect it CENTRAL HEATING SYSTEM The central heating system must comply with BS 5449 part 1 If the system is to be a combined heating and domestic hot water system then a double feed indirect hot water storage cylinder to BS 1556 part 1 should be used In order to prevent the build up of scale and corrosion a suitable inhibitor should be used The system must be correctly vented as shown in Figs 4 and 5 The height differential between the header tank and the appliance must not exceed 15 2 metres 50 feet If all four boiler tappings are used then if possible diagonal pair2. RUNNING THE FIRE WITH THE DOORS OPEN The fire may be run with the doors open if required The more reactive fuels such as wood peat coal and homefire will burn better with the doors open than fuels like phurnacite and ancit Do not leave the fire unattended with the doors open OVERNIGHT BURNING For overnight burning the fire doors must be closed When burning wood load some large logs on the fire and allow to burn for half an hour before closing the door air slides this will help to reduce tar deposits in the chimney Leave the airwash control slightly open to help keep the glass clear When burning coal or smokeless fuel if the fire is very low then open the air controls and revive the fire adding a small amount of fuel if necessary Empty the ashpan and poke the fire load with fuel and then close the door air slides The airwash control should be kept slightly open to help keep the door glass clean Some experimentation may be necessary to find the setting most suitable for the type of fuel being used and the draw on the chimney To revive the fire empty the ashpan if burning coal or smokeless fuel poke the fire and open the air controls to maximum When the fire is burning well load on more fuel as necessary and adjust the air controls to the desired setting CLEANING AND MAINTENANCE The stove is finished with a high temperature paint which will withstand the temperatures encountered in
3. ensuring that there is sufficient heat Connect the heating system to the boiler ensuring that the primary flow pipe rises continuously from the appliance to the vent Fill the system with water and check for leaks SYSTEM CONTROLS Since the controls on the stove are manually operated we strongly recommend using high and low limit pipe thermostats to control the pump The high limit anti boiling thermostat should be fitted on the gravity flow pipe as near to the boiler as possible and the low limit anti condensation thermostat should be fitted on the gravity return again as near to the boiler as possible but ensuring that it is not on the common part of the return if only one return tapping is used Set the high limit thermostat at 85 C and the low limit thermostat at 45 C Radiators may be either manually or thermostatically controlled CONNECTIONS TO FLUES There are several ways of connecting the stove to the flue These are illustrated in Figs 8 to 11 If the top flue connection or the optional vertical rear flue connector is used then chimney may be swept through the appliance Horizontal lengths of flue must be kept to a minimum and should not be more than 150mm 6 inches long The sealing face of the flue collar must be coated with fire cement before fixing to the body of the stove using the two screws provided The blanking plate must be removed sealed with fire cement and refitted care bei
4. normal use This may be cleaned with a damp lint free cloth when the stove is cold Should re painting become necessary high temperature paints are available from your supplier or from stove shops Most deposits on the glass may be burnt off simply by running the fire at a fast rate for a few minutes If it becomes necessary to clean the glass then open the doors and allow them to cool Clean the glass using a damp cloth and then wiping over with a dry cloth Any stubborn deposits on the glass may be removed with a proprietary stove glass cleaner or ceramic hob cleaner Do not use abrasive cleaners or pads as theses can scratch the surface which will weaken the glass and cause premature failure THROAT PLATE AND FLUEWAY CLEANING It is important that the throat plate and all the stove flueways are kept clean in order to prevent potentially dangerous fume emission They should be cleaned at least monthly and more frequently if necessary It is necessary to let the fire out completely to carry out these operations The front of the throat plate is pulled forward and then lowered as shown in Fig 2 Any sooty deposits should then be swept from the plate and into the fire Return the throat plate to its correct position raise the front of the plate push it back and then lower it onto the retaining lugs CHIMNEY SWEEPING The chimney should be swept at least twice a year Where the top outlet or vertical rear flue con
5. some of it may be removed If burning solid fuel clear the grate and empty the ashpan before relighting CONTROLLING THE FIRE The rate of burning and hence the output is controlled by the door air slides and the airwash control see Fig 1 The air slides in the doors should be used when lighting or when rapid burning is required They should not be left fully open for long periods as this can cause over firing For overnight burning they should be closed The airwash control is used most of the time to control the burning rate and to keep the glass clean Fully extended gives full airwash for faster burning and clean glass whereas fully closed gives slow overnight burning It will not be possible to keep the glass clean if this control is fully closed particularly after refuelling REFUELLING Keep the firebox well filled but do not allow fuel to spill over the top of the front fire bars Care should be taken especially when burning wood that fuel does not project over the front fire bars or damage to the glass may be caused when the doors are closed it can also cause the glass to black up Thro Plate Pull Forward and Swing Down Fig 2 Throat Plate Position and Lowering ASH CLEARANCE When burning wood or peat the ash should be allowed to build up on the base of the fire It will only be necessary to remove some ash once or twice a week when it begins to r
6. the chimney does not suffer from down draught When the chimney is warm the draw should be not less than 2 5mm 0 10 inches water gauge If in doubt about the chimney seek expert advice HEARTH AND FIRE SURROUND The stove must stand on a fireproof hearth and must be situated at least 300mm 12 inches from any combustible material There must be a gap behind the stove of at least 25mm to allow air to enter the airwash inlets The positioning of the stove and the size of the hearth are governed by building regulations for Class appliances These building regulations state that the hearth must extend in front of the stove by at least 300mm 12 inches and to the sides of the stove by at least 150mm 6 inches If in doubt as to the positioning of the stove expert advice should be sought either from the supplier or the local building inspector The fireplace must allow good circulation of air around the appliance to ensure that maximum heat is transferred to the room and also to prevent the fireplace from overheating A gap of 150mm 6 22mm Open Vents Feed and Expansion Tank ood Water Tank Overflow 7 Overflow Domestic Hot Water Draw Off Indirect Hot Water Cylinder High Limit Thermostat Low Limit Thermostat X Drain Cock at Lowest Point Fig 4 Typical Central Heating amp Hot Water System Using 4 Boiler Tappings 22mm Open Vents Feed and Expansion Tank Cold Water Tank x
7. the doors tighten properly COMMISSIONING On completion of the installation and after allowing a suitable period of time for the fire cement and mortar to dry out make a layer of ash or sand on the base of the stove before lighting it and checking to ensure that smoke and fumes are taken from the appliance up the chimney and emitted safely Also check all joints and seals On completion of the installation and commissioning please leave the operating instruc tions with the customer and advise them on the use of the appliance Country 8B Woodburner Overall Dimensions all dimensions are in mm Page 9 Country 8B WB _ 10 00
8. CHARNWOOD COUNTRY 8B WOODBURNER WITH BOILER Operating and Installation Instructions BY A J WELLS amp SONS Bishop s Way Newport Isle Of Wight PO30 5WS U K Tel 01983 527552 Fax 01983 821267 CHARNWOOD COUNTRY 8B WOODBURNER OPERATING INSTRUCTIONS Before lighting the stove check with the installer that the work and checks described in the Installation Instructions have been carried out correctly and that the chimney has been swept is sound and free from any obstructions FUELS Wood Wood must be dry and well seasoned Ideally it should be cut split and stacked under cover for at least a year and preferably two years before being burnt Hard woods such as Ash Beech and Oak are preferable to Soft woods such as Pine The wood should be burnt in a bed of ash on the flat base of the stove Burning wet unseasoned wood will result in heavy tar deposits in the chimney and reduced outputs Peat Cut peat should be dried before burning to reduce tar deposits Peat should be burnt in the same manner as wood on the flat base of the stove in a bed of ash House Coal Doubles Trebles and Cobbles may be burnt do not use singles or coal dust or slack Coal must only be burnt with the optional coal kit burning it on the flat base of the stove may cause dam
9. NWOOD COUNTRY 8B WOODBURNER INSTALLATION INSTRUCTIONS HEALTH AND SAFETY PRECAUTIONS Please take care when installing the stove that the requirements of the Health and Safety at Work Act 1974 are met Some types of fire cement are caustic and should not be allowed to come into contact with the skin In case of contact wash with plenty of water If there is a possibility of disturbing any asbestos in the course of installation then please use appropriate protective equipment There must not be an extractor fan fitted in the same room as the stove as this can cause the appliance to emit fumes into the room There must be an adequate air supply into the room in which the appliance is installed totalling at least 100 square cm 16 square inches to provide combustion air This is particularly necessary if the room is double glazed In addition to these instructions the requirements of BS 8303 and BS 6461 Pt 1 amp 2 1984 must be fulfilled Local Authority Bylaws and Building Regulations regarding the installation of Solid Fuel burning appliances flues and chimneys must also be observed PERFORMANCE The output of the Country 8B WB is 7 0 kW 23 800 Btu h to water and 2 5 kW 8 500 Btu h to the room These outputs are based on a 2 hourly re fuelling cycle burning seasoned hardwood logs or a 4 hourly re fuelling cycle burning smokeless fuel CHIMNEY In order for the appliance to perform satisfactorily the chim
10. age A little extra care is needed when burning coal please refer to the section Special Points When Burning House Coal later in the instructions Smokeless Fuel A wide variety of smokeless fuels are available many of which are suitable for use on your Country 8 Some of these are listed below Ancit Anthracite Large Nuts Centurion Extracite Homefire Maxibrite Phurnacite Welsh Dry Steam Coal Large Nuts Smokeless fuels must only be burnt with the optional coal kit burning it on the flat base of the stove may cause damage At first you may find it helpful to try several fuels to find the most suitable If you are unable to obtain the fuel you want ask your supplier or an approved fuel distributor to suggest an alternative Only smokeless fuels may be burnt in smoke control areas Airwash Control osed lt Open Door Knob 3 To Open Door Airslide Open lt gt Closed Door Airslide Closed lt gt Open Fig 1 Stove Controls Page 2 Country 8B WB 10 00 DOOR OPERATION Turn the right hand door knob anti clockwise to open and clockwise to close see Fig 1 FITTING THE OPTIONAL COAL KIT Before burning coal or smokeless fuel the coal kit must be fitted This consists of a grate and an ashpan Fit the legs onto the grate ensuring that the grate is the right way up fill the holes around the legs with fire cement Remove the fron
11. blockage For your own safety these must be kept clean Fire blazing out of control Check that a The doors are tightly closed b The airslides are turned down to the minimum setting c The airwash control is closed d A suitable fuel is being used e Door seals and airwash slide are intact Page 5 Country 8B WB 10 00 Over Firing If the fire is over fired it will cause premature failure of the internal fire parts Overfiring is occurring when any parts of the fire begin to glow red To prevent over firing ensure that a the door seals are kept in good condition and that the doors are sealing correctly b the air controls on the fire is working correctly c a suitable fuel is being used d the fire is not fitted onto a heating system which is too large Chimney Fires If the chimney is thoroughly and regularly swept chimney fires should not occur However if a chimney fire does occur close the door air slides and the airwash control and tightly close the doors of the appliance This should cause the chimney fire to go out in which case the controls should be kept closed until the stove has gone out The chimney and flueways should then be cleaned If the chimney fire does not go out when the above action is taken then the fire brigade should be called immediately After a chimney fire the chimney should be carefully examined for any damage Expert advice should be sought if necessary CHAR
12. estrict the flow of air through the front fence When burning coal or smokeless fuel the ashpan should be emptied regularly before it becomes too full generally once or twice a day Never allow the ash to accumulate in the ashpan so that it comes in contact with the underside of the grate as this will seriously damage the grate Care should be taken to ensure that ash is cool before emptying it into plastic liners or bins After emptying the ashpan poke the fire with a poker to clear the firebed of ash To make ash removal easier when burning coal or smokeless fuel there is a special Charnwood ash carrier available This enables the whole ashpan to be placed in the sealed carrier and taken outside These may be purchased from your supplier or in case of difficulty from ourselves Page 3 Country 8B WB _ 10 00 SPECIAL POINTS WHEN BURNING HOUSE COAL When loading the stove take care not to smother the fire instead fill the firebox in two stages waiting between each stage for the flames to appear above the fire After a period of slumbering always open the door air slides and wait until flames appear above the fuel bed before opening the doors Burning coal will produce more soot deposits than other fuels especially if the fire is run at low levels for long periods It is therefore vital to clean the throat plate regularly weekly cleaning is recommended Never fully close the Airwash control when burning coal
13. front fence This will not obscure the view of the fire or affect its performance Freezing Do not light the fire if there is any possibility that any parts of the system may be frozen Lack of Heat To Radiators Hot Water Check that a the fire is burning properly if not then carry out the checks under Fire Will Not Burn b the throat plate is fitted correctly see Fig 2 and that it is not distorted c the door seals are in good condition d If the hot water goes cold when the pump is turned on or if some radiators are hotter than others then the system may need balancing the pump may be pumping the water too quickly around the system or the radiators may need bleeding Please ask your installer to check these points Fume Emission Warning Note Properly installed and operated this appliance will not emit fumes Occasional fume from de ashing and re fuelling may occur Persistent fume emission is potentially dangerous and must not be tolerated If fume emission does persist then the following immediate actions should be taken a Open doors and windows to ventilate the room b Let the fire out and safely dispose of the fuel from the appliance c Check for flue or chimney blockage and clean if required d Do not attempt to re light the fire until cause of fume has been identified if necessary seek professional advice The most common cause of fume emission is flueway or chimney
14. nector is used it will generally be possible to sweep the chimney through the appliance First remove the front fence and the throat plate Then sweep the chimney ensuring that soot is removed from all horizontal surfaces after sweeping In situations where it is not possible to sweep through the appliance the installer will have provided alternative means such as a soot door After sweeping the chimney the appliance flue outlet and the flue pipe connecting the stove to the chimney must be cleaned with a flue brush After clearing any soot from within the stove replace the throat plate see Fig 2 and the front fence Different types of sweep s brushes are available to suit different flueways For standard brick chimneys a wire centre sweep s brush fitted with a guide wheel is recommended For prefabricated insulated chimneys the manufacturers instructions with regard to sweeping should be consulted TROUBLE SHOOTING Fire Will Not Burn Check that a the air inlet is not obstructed in any way Page 4 Country 8B WB _ 10 00 b chimneys and flueways are clear c that a suitable fuel is being used d that there is an adequate air supply into the room e that an extractor fan is not fitted in the same room as the stove f there is sufficient draw in the chimney Once the chimney is warm a draught reading of at least 2 5 mm 0 10 inches water gauge should be obtained Door Glass Blacks Up Difference
15. ney height must not be less than 4 metres measured vertically from the outlet of the stove to the top of the chimney The internal dimensions of the chimney should preferably be 175 mm 7 inches or 200mm 8 inches either square or round and MUST NOT BE LESS THAN 150 mm 6 INCHES Boiler Output kW 8 0 6 0 4 0 1 0 2 0 Space Output kW Fig 3 Performance Chart If an existing chimney is to be used it must be swept and checked it must be in good condition free from cracks and blockages and should not have an excessive cross sectional area If you find that the chimney is in poor condition then expert advice should be sought regarding the necessity of having the chimney lined If it is found necessary to line the chimney then a lining suitable for Solid Fuel must be used If there is no existing chimney then a prefabricated block chimney or a twin walled insulated stainless steel flue to BS 4543 can be used either internally Page 6 Country 8B WB _ 10 00 or externally These chimneys must be fitted in accordance with the manufacturers instructions and Building Regulations Single wall flue pipe is suitable for connecting the stove to the chimney but is not suitable for using for the complete chimney If it is found that there is excessive draw in the chimney then a draught stabilizer should be fitted It is important that there is sufficient draw in the chimney and that
16. ng taken to ensure that the fold on the blanking plate is in line with the lugs on the firebox as shown in Fig 7 Ensure that the clamping plate does not prevent the throat plate from seating correctly All flue connections must be well sealed SOOT DOORS It is possible to pass a 16 inch diameter sweeps brush through the appliance but in most back outlet installations it will be necessary to have a soot door to enable the chimney to be swept The optional vertical rear flue connector does allow the chimney to be swept through the stove Soot doors may either be in the actual brickwork of the chimney or in the register plate Various positions of soot doors are shown in Figs 8 to 11 PRE LIGHTING CHECK Ensure that the throat plate is fitted Page 8 Country 8B WB 10 00 Soot Door In Side or Rear Of Chimne Fig 8 Vertical Register Plate With Bricked Up Fireplace Alternative Soot Door Positions Register Plate With Soot Door Fig 9 Horizontal Register Plate With Rear Flue Connection Alternative Soot Door Positions Fig 10 Horizontal Register Plate With Top Flue Connection Alternative Soot Door Positions Register Plate With Soot Door Fig 11 Horizontal Register Plate With Optional Vertical Rear Flue Connector in the roof of the appliance The location and positioning of the throat plate is shown in Fig 2 Before initial lighting check that the front fence is fitted correctly and that
17. s should be connected for domestic hot water and central heating Where a common return is used an injector tee must be incorporated into the system as shown in Fig 6 This will ensure that a good domestic hot water supply is maintained when the central heating pump is operating The system must incorporate a gravity circuit which will normally heat the domestic hot water and an unvalved radiator with an output of at least 1 kW When the appliance is not connected to a domestic hot water system the unvalved radiator s on the gravity circuit must have an output of at least 1 25 kW This is to prevent boiling in case of pump failure All pipework in the primary circuit must be 28 mm diameter and the gravity flow pipe must rise continuously from the boiler to the open vent Two typical systems are shown in Figures 4 and 5 Blanking Plate Back of the Stove TEA Clamping Plate Blanking Plate with fold horizontal Clamping plate finishes flush with inside face of firebox top and bottom Seal Blanking Plate with fire cement Fig 7 Flue Blanking Plate If the appliance is used to heat a very small central heating system then the heat output to the room from the fire will be reduced Fig 3 shows the ratio of space heating to water heating which can be expected Fitting a radiator in the same room as the fire is recommended as it will allow greater flexibility in the way that the system is operated as well as
18. s in chimney draughts mean that the best settings of the air controls will vary for different installations A certain amount of experimentation may be required however the following points should be noted and with a little care should enable the glass to be kept clean in most situations a The airwash relies on a supply of heated air to keep the glass clean therefore when lighting the stove allow the firebed to become well established before closing the airslides This may also be necessary when re fuelling the stove b When re fuelling keep the fuel as far back from the front fence as possible do not try to fit too much fuel into the firebox c Never completely close the airwash control as a guide it should be at least a quarter open d The airslides in the doors may be kept slightly open to assist in keeping the glass clean e Wet wood or logs overhanging the front fence will cause the glass to blacken It is always more difficult to keep the glass clean when running the stove very slowly for long periods If blackening of the glass still occurs check that all flue connections and the blanking plate are well sealed It is also important that the chimney draw is sufficient and that it is not affected by down draught When the chimney is warm a draught reading of at least 2 5 mm 0 10 inches water gauge should be obtained When burning coal some blackening of the glass may occur below the level of the
19. t fence and place the grate in the stove so that it comes hard up against the back fire brick Replace the front fence so that the slope rests on the top of the grate Slide the ashpan in under the grate LIGHTING On initial lighting the stove may smoke and give off an odour as the silicon paint with which the firebox is painted reacts to the heat This is normal and will cease after a short time but meanwhile the room should be kept well ventilated At first only light a small fire and burn it slowly for two hours to allow any residual moisture in the bricks to evaporate IMPORTANT When burning wood or peat on the base of the stove there must be a bed of ash to prevent damage to the base When first lighting the stove if there is no ash available then a make a layer of sand or earth about 12mm 1 2 inch thick on the base to prevent any damage The stove may be lit using dry kindling wood and paper or fire lighters Place the paper or fire lighters and kindling on the base or the grate and cover with approximately 2 inches of fuel Open the air slides in the doors and open the airwash control fully see Fig 1 Light the paper or fire lighters Close the doors until the fuel is well ignited then load with fuel and adjust the air controls to the required setting When relighting the stove leave the ash on the base if burning wood or peat unless it is beginning to block the slots in the front fence in which case
Download Pdf Manuals
Related Search