Audiovox VX6020 Installation Manual
Contents
1. Radio Ant Camera LZ of Rear Video Rep 115 0000000 Yellow Camera Video LEFT FRONT SPEAKER LEFT FRONT SPEAKER RIGHT FRONT SPEAKER RIGHT FRONT SPEAKER RIGHT REAR SPEAKER RIGHT REAR SPEAKER LEFT REAR SPEAKER LEFT REAR SPEAKER BATTERY 12V CHASSIS GROUND ACC IGNITION ILLUMINATION GPS Antenna KEY A SWC A Primary programming lead KEY A SWC B Secondary programming lead SWC A and SWC B are to be connected to the two leads of the SWC harness in the automobile The third wire SWC GND is to be connected to the lead identified as Ground on the SWC lead diagram for the specific automobile Wiring of the SWC lead in the auto steering wheel may vary depending on the type of automobile Please consult the wire harness diagram for the pinout of your specific automobile s SWC configuration Some automobiles may not be compatible with this 3 wire SWC resistive input AVX recommends that installation of this radio be performed by a professional installer JENSEN Audiovox Electronics Corporation Hauppauge NY 11788 Technical Assistance 1 800 323 4815 www jensenmobile com 2013 Audiovox Printed in China 128 9244a2. Installation Guide T VX6020 ne What s in the Box Tools and Supplies j The following items are supplied with The following tools and supplies are the VX6020 needed to install the VX6020 e VX6020 Head Unit Torx type flat head and Philips e Custom Cosmetic Trim Ring screwdrivers e Hardware Bag e Wire cutters and strippers J e Power Speaker Output Harness Tools to remove existing radio screw GPS Antenna Harness driver socket wrench set or other DER U Mini USB Adapter eae e A to Mini apte fT Owners Manual amp Warrenty Card F ectiigal tape e Installation Guide Crimping tool Volt meter test light Crimp connections 18 gauge wire for power connections V e 16 18 gauge speaker wire Optional Equipment e Steering Wheel Control SWC The VX6020 is SWC ready for vehicles equipped with the option See wiring diagram for installation details e Rear Camera The VX6020 is Rear Camera ready for vehicles equipped with the option See wiring diagram for installation details Disconnect the Battery To prevent a short circuit be sure to turn off the ignition and remove the negative battery cable prior to installation NOTE If the VX6020 is to be installed in a car equipped with an on board drive or navigation computer do not disconnect the battery cable If the cable is disconnected the computer memory may be lost Under these conditions use extra caution duri
3. es not operate re check all wiring until the problem is corrected 4 Mount the new radio assembly to the dashboard or center console using the reverse procedure in step 1 above CAUTION Be careful not to damage the car wiring NOTE It is the end users responsibility to install and operate this unit ina manner in accordance with local state and federal laws The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual Using the Cosmetic Trim Ring Acosmetic trim ring is supplied with the head unit for installation flexibility This unit will fit into most import dashes with little or no modification to the dash board cavity Some US domestic vehicle dashes will accept a Double DIN chassis but there is usually a small gap between the radio and dash piece after installation is complete In this case use the appropriate trim ring to conceal any gaps that may be present NOTE For proper operation of the CD DVD player the chassis must be mounted within 30 of horizontal Make sure the unit is mounted within this limitation fully instructions care wiring ins BLUE POWER ANTENNA amp AMPLIFIER TURN ON ons can damage the unit Follow the or have the installation handled by an experienced technician Incorrect wiring connecti iagram D CAUTION IMPORTANT iring Need Help For technical assistance call the Jensen customer support line at 1 800 323 4815 WwW Power On Trigger Wire Backup
4. ng installation to avoid causing a short circuit Replacing the Fuse e When replacing the vehicles Radio fuse always use the proper rated replacement fuse Using a fuse with an improper rating could damage the unit and cause a fire ISO DIN Installation The VX6020 is designed to fit into a 2 0 DIN dashboard opening The unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota Nissan Mitsubishi Isuzu Hyundai and Honda vehicles to mount the radio to the dashboard Please consult with your local car stereo specialty shop for assistance on this type of installation 1 Remove the existing factory radio from the dashboard or center console mounting Save all hardware and brackets as they will be used to mount the new radio 2 Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio CAUTION Do not exceed M5 X 6MM screw size Longer screws may damage components inside the chassis 3 Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve Follow the wiring diagram carefully and make certain all connections are secure and insulated with wire nuts or electrical tape After completing the wiring connections plug the ISO connectors into the mating sockets on the rear of the chassis Turn the unit on to confirm operation vehicle ignition switch must be on If the unit do
Download Pdf Manuals
Related Search