AT&T TL7612 User's Manual
Contents
1. Headset base and handset lifter installation Installation of large lifter pad optional If the small lifter pad cannot hold the corded handset steadily you can attach a large lifter pad provided to enlarge the contact area 1 Hold the large lifter pad in front of the small lifter pad as shown below 2 Insert the large lifter pad into the two front gaps of the small lifter pad Installation of anti slip pad optional The anti slip pad provided helps prevent your corded handset from slipping from the Lifter 1 Choose an appropriate position for the anti slip pad above the small lifter pad 2 Peel off the protective strip from the anti slip pad 3 Carefully stick the anti slip pad to your chosen position You may now place the corded handset back onto the lifter Adhesive tape Protective strip 21 About internal and auxiliary ring detectors The internal or auxiliary ring detector detects the telephone ringer and sends a ring tone to the headset earpiece If you installed the lifter over the top of the corded phone speaker the internal ring detector will recognize when the phone rings However if your corded phone speaker is located elsewhere on the phone stick the auxiliary ring detector to the speaker as shown below Install the auxiliary ring detector 1 Insert the auxiliary ring detector plug into the RING DETECT jack on the lifter 2 Remove the protective strip from the adhesive tape on2. a ring tone to the headset earpiece Adhesive tape Remove the protective strips before attaching the lifter to the telephone base Quick reference guide handset lifter STATUS light On when the headset is not in use and the ring detector is turned off Flashes slowly when the headset is in use and the ring detector is turned off On when the headset is not in use and the ring detector is turned on Flashes four times every three seconds when the ring detector detects an incoming call Flashes slowly when the headset is in use and the ring detector is turned on The headset base does not have power The lifter control cable is not plugged into the LIFTER jack on the headset base Battery installation Install the battery as shown below After installing the battery you may be able to make and receive short calls For optimal performance charge the headset battery for at least six hours before use When the headset is not in use recharge the headset by returning it to the headset base 1 Insert the battery into the battery Push the battery plug into the Insert the tab on the bottom of the Press down gently on the battery If the battery compartment cover is attached press on both sides of the cover and lift it up and off compartment with the label THIS SIDE UP facing up connector inside the compartment according to the color coded label Place the wires neatly inside the compar
3. base mode is set to NO LIFTER MODE e Plug the small end of the headset base power e Plug one end of the telephone line cord into the TEL WALL JACK red dot at the back of adapter into the the headset base POWER jack green dot at the back of the headset base e Plug the other end of the telephone line cord into the line splitter Telephone line cord e Plug the line splitter into the telephone wall jack or DSL filter if Line splitter you subscribe to DSL Internet service e Plug the headset base power adapter eS a into an electrical outlet not controlled E a _ not included is by a wall switch 2 D required if you have a D9 DSL high speed Internet service pect G O O e Connect another Cordless or corded hehe te wie cole phone between the telephone and the line splitter 25 Headset operation Making a call When the headset base is connected to a corded handset of your telephone with the handset lifter installed option 1 You must select LIFTER MODE on the headset base 1 Press on the headset The switch hook presser rises and releases the switch hook You hear a dial tone in the headset earpiece 2 Dial the telephone number using the dialing keys When the headset base is connected to a telephone wall jack option 2 You must select NO LIFTER MO
4. decrease the sensitivity When the ring detector detects the telephone ringer correctly e The STATUS light on the lifter flashes quickly when the telephone rings e The detector sends the ring tone to the headset earpiece 23 Headset base installation Option 2 Connect the headset to a telephone wall jack In order to make calls using this installation option you need a telephone plugged into the same telephone line or a dial pad TL7601 purchased separately Make sure the headset base mode is set to NO LIFTER MODE e Plug the small end of e Plug one end of the headset base power the telephone line adapter into the POWER f cord into the jack green dot at the TEL WALL JACK back of the headset base red dot at the back of the ZO headset base f 0 Doo m E LIFTER POWER a inex wey vi M Telephone lt p line cord e Plug the other end of the telephone line cord into a telephone jack e Plug the headset Ne base power adapter A DSL filter not included is required if you have DSL outlet not controlled high speed Internet service into an electrical by a wall switch Q NOTE For more information about the accessory dial pad model TL7601 visit our website at WWW telephones att com 24 Headset base installation Option 3 Connect the headset to a corded or cordless phone To use this installation option make sure the headset
5. pressed to go on hook or off hook Quick reference guide headset base Charging cradle Insert the headset here for charging PAIR Press to register or deregister the headset NO LIFTER MODE light On when NO LIFTER MODE is selected Flashes while on a call or another telephone is in use on the same line Flashes quickly when there is an incoming call LIFTER MODE light On when LIFTER MODE is selected Flashes while on a call Flashes quickly when there is an incoming call MUTE light On when a call is muted Quick reference guide headset base LIFTER AUDIO ADJUST Switch to choose the best headset audio quality when using LIFTER MODE VOLUME b AV Press the volume keys on the side of the headset base to adjust the speaking volume while on a call LS Press to choose between o S NO LIFTER MODE or LIFTER MODE when the headset is not in use The corresponding light turns on Quick reference guide headset base Headset base indicator lights NO LIFTER MODE LIFTER MODE On when NO LIFTER MODE is selected default mode Flashes quickly when there is an incoming call Flashes when the headset is in use or another telephone on the same line is in use On when LIFTER MODE is selected Flashes quickly when there is an incoming call Flashes when the headset is in use On when a call is muted On when y
6. DE on the headset base 1 Follow the instructions in your telephone user s manual for making calls 2 Press ON off on the headset at any time to join the call 3 After you join the call on the headset you can hang up the telephone and continue the call on the headset When the headset base is connected to a corded or cordless phone option 3 You must select NO LIFTER MODE on the headset base 1 Use the dial pad for making calls 2 Press ON OFF on the headset at any time to join the call 26 Headset operation Answering a call on the headset When the headset base is connected to a corded handset of your telephone with the handset lifter installed option 1 e Press ON OFF on the headset The switch hook presser rises and releases the switch hook You hear the caller through the headset earpiece When the headset base is connected to a telephone wall jack or connected to a corded or cordless phone option 2 or 3 e Press ON OFF on the headset Ending a call on the headset When the headset base is connected to a corded handset of your telephone with the handset lifter installed option 1 e Press ON OFF on the headset or place the headset in the headset base to end a call The switch hook presser pushes down the switch hook and ends the call When the headset base is connected to a telephone wall jack or connected to a corded or cordless phone option 2 or 3 e Press ON OFF on the headset or place the h
7. This option enables you to use the headset with a single telephone line with or without a telephone Connect the headset to a corded or cordless telephone page 25 You can use the provided line splitter to connect the headset to a telephone 15 Headset base and handset lifter installation Option 1 Connect the handset lifter to a corded phone 1 Unplug the curly handset cord from the telephone and plug it into the s CURLY CORD jack light blue dot on the headset base 2 Plug one end of the telephone line cord provided with the headset base into the base handset jack on the telephone where the curly handset cord was originally plugged in 3 Plug the other end of the line cord into the BASE JACK orange dot on the headset base 4 Plug the lifter control cable into the jack of the base adapter 5 Plug the other end of the base adapter into the LIFTER jack blue dot on the headset base Adjust the corded handset audio see page 17 before you install the handset lifter to your telephone See page 18 to attach the handset lifter Make sure the headset base mode is set to LIFTER MODE Plug the small end of the headset base power adapter to the POWER jack green dot on the headset base A fT i Plug the large end of the headset base power adapter into a power outlet not controlled by a wall switch Telephone wall jack A DSL filter not included is required if you have DSL high speed Internet ser
8. atat Quick start guide TL7612 DECT 6 0 cordless headset and handset lifter Installation You must install and See pages 10 11 charge the battery before for instructions using the headset If you subscribe to high speed Internet service DSL digital subscriber line through your telephone line you must install a DSL filter between the telephone line cord and the telephone wall jack The filter prevents noise and caller ID problems caused by DSL interference Please contact your DSL service provider for more information about DSL filters For customer service or product information visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 Avoid placing the headset base too close to e Communication devices such as television sets VCRs or other cordless telephones e Excessive heat sources e Noise sources such as a window with traffic outside motors microwave ovens refrigerators or fluorescent lighting e Excessive dust sources such as a workshop or garage e Excessive moisture e Extremely low temperature e Mechanical vibration or shock such as on top of a washing machine or work bench Quick reference guide headset Flashing ON OFF Press to make and or answer a call and to end a call Headset is charging in the headset base Headset is trying to register to the headset base Headset is searching for the headset base Flashes slowly wh
9. ce as shown in Figure 2 Figure 2 12 Headset base and handset lifter installation No lifter mode or lifter mode There are two answer modes available on the headset bese The current mode is indicated J by the NO LIFTER MODE or LIFTER MODE lights on the front of the headset base e When plugging your headset base into the telephone wall jack make sure the headset base mode is set to NO LIFTER MODE OR MODE e When connecting your headset base to a corded telephone make sure the headset base mode is set to LIFTER MODE and that the LIFTER AUDIO ADJUST is switched for the best headset audio quality To change the answer mode When the headset is not in use press MODE on the headset base to select NO LIFTER MODE or LIFTER MODE The corresponding light on the front of the headset base turns on to indicate the current mode QO NOTE If you are using the handset lifter you must use the LIFTER MODE 13 Headset base and handset lifter installation Cord labels The cords provided with your headset have colored labels attached to help you plug them into the headset base The back of the headset base has colored dots above the jacks and the names of the jacks on the rear bottom piece of the headset base corresponding to the colored labels on the cords If you are using installation option 1 you can attac
10. eadset in the headset base 27 atat www telephones att com 2011 Advanced American Telephones All Rights Reserved AT amp T and the AT amp T logo are trademarks of AT amp T Intellectual Property licensed to Advanced American Telephones San Antonio TX 78219 Printed in China Issue 1 AT amp T 03 11
11. en an incorrect type of battery is installed Flashes three times followed by a pause then repeats this cycle three more times and then shuts down to indicate the battery is very low Flashes twice every five seconds to indicate the headset is not registered Flashes every 20 seconds to indicate the battery is low and needs to be charged in the headset base Flashes every three seconds to indicate the headset is in use Flashes quickly when there is an incoming call Quick reference guide headset VOLUME 9 Press the volume keys on the side of the headset to adjust the listening volume when on a call MUTE FLASH Press to mute the microphone during a call Press and hold to answer a call waiting call while on a call Earpiece Press to mute the ring tone in the earpiece when there is an incoming call Microphone Battery cover Open to install or replace the battery Quick reference guide headset Headset alert tones Three quick beeps e VOLUME 2 keys are pressed when the volume is already at its highest or lowest setting e The headset is not registered and the headset ON oFF button was pressed e The headset is out of range from the headset base during a call One short beep Low battery warning every 20 seconds One short beep The call is muted every 15 seconds One long beep Call waiting alert tone repeated One short beep The headset ON OFF key is
12. h the provided light blue colored label to the end of the curly handset cord of your telephone that you plug into the headset base Digital subscriber line DSL If you subscribe to high speed Internet service DSL digital subscriber line through your telephone line you must install a DSL filter between the telephone base and the telephone wall jack The filter prevents noise and caller ID problems caused by DSL interference Please contact your DSL service provider for more information about DSL filters 14 Headset base and handset lifter installation Installation options You have three installation options Option 1 Connect the handset lifter to a corded phone pages 16 Option 2 Option 3 23 This option enables you to answer calls even if you are away from the telephone base For this option you can use the headset with a single line or multiple line corded telephone such as the AT amp T 1080 1070 or 1040 or a digital business system such as a proprietary PBX telephone system The handset lifter lifter works with the cordless headset to provide a complete communication solution for most corded telephones The lifter raises and lowers its switch hook presser to answer make and end phone calls The ring detector provides an incoming call indication through the cordless headset so you can answer calls even when you are away from the telephone base Connect the headset to a telephone wall jack page 24
13. one switch hook Adjust the height of the lifter arm Turn the ADJUST LIFTER knob to change the height of the lifter arm When in the raised position the arm should release the switch hook so you can hear a dial tone When lowered the arm should hold the switch hook down so that there is no dial tone Z ADJUST LIFTER Headset base and handset lifter installation Lifter adjustments and testing 1 Make sure that the headset base is set to LIFTER MODE and that the LIFTER AUDIO ADJUST setting is correct 2 Turn the switch hook presser adjustment knob until the switch hook presser is just above the switch hook 3 Lower the lifter arm until the switch hook presser holds the switch hook down 4 Place the corded handset on the lifter 5 Press ON OFF on the headset The switch hook presser should rise and release the switch hook on your telephone base Make sure you hear a dial tone through your headset earpiece 6 If the switch hook is not fully released turn the ADJUST LIFTER knob while the corded handset is on the lifter When the switch hook is fully released you will hear a dial tone from the headset It may take some adjustments and testing to find the right position for the lifter For the lifter to work properly the switch hook must release completely when you press ON OFF to turn the headset on The switch hook must also be held down completely when you press ON OFF to turn the headset off 20
14. ou are registering a headset Flashes when you are deregistering the headset s or dial pad from the headset base Quick reference guide handset lifter SENSOR ADJ knob Adjusts the sensitivity of the ring detector ADJUST LIFTER knob Adjusts the height of the lifter arm Lifter arm Holds the corded telephone handset RING DETECT ADJUST LIFTER Switch hook presser When the CORDED HANDSET CONNECTED switch is set to YES pressing ON OFF on the headset raises or lowers the switch hook presser Lifter control cable RING DETECT jack This cable is hard wired into the lifter Plug in the auxiliary ring and plugs into the LIFTER jack on the detector headset base Quick reference guide handset lifter 1 4H0 NO ONY n m 2 a a gt i RING ON OFF Press to turn the ring detector on or off When the ring detector is off the cordless headset does not ring SALVLS i Switch hook presser adjustment knob Adjusts the position of the switch hook presser Small lifter pad Holds the earpiece of the corded telephone handset STATUS light On in red when the ring detector is off On in blue when the ring detector is on and the headset not in use Flashes blue four times every three seconds when the ring detector detects an incoming call Flashes blue slowly when the switch hook presser is raised and you are on a Call Internal ring detector Detects the telephone ringer and sends
15. the auxiliary ring detector 3 Stick the auxiliary ring detector to the center of the corded phone speaker Auxiliary ring detector Speaker faNeoerecr ADIUSTUFTER Adhesive tape RING DETECT jack RING DETECT jack Auxiliary ring detector plug 22 About internal and auxiliary ring detectors Ring detector on off When the ring detector detects an incoming call it sends a ring tone to the headset earpiece e Press the RING ON OFF button on the lifter to turn the ring detector on or off The STATUS light is blue when the ring detector is turned on and red when the ring detector is turned off e When the ring detector is turned off it does not send a ring tone to the headset a gt ioe 440 NO ONIY NOTE When you are using the speakerphone of your telephone the ring detector may send a ring tone to the headset If you do not want the headset to ring press the RING ON OFF button to turn the ring detector off After the call you can press the RING ON OFF button again to turn the ring detector back on Adjust the sensitivity level The default setting of the ring detector works with most corded telephones However the ring detector might need some adjustments to recognize less common telephone ring tones To adjust the ring detector sensitivity while the telephone is ringing e Turn the SENSOR ADJ knob clockwise to increase the sensitivity e Turn the SENSOR ADJ knob counterclockwise to
16. tment battery compartment cover into the battery compartment compartment cover until it snaps into place Q NOTE Remove the ear hook from the headset before battery replacement 10 Battery charging After installing the battery charge the headset by placing it on the headset base as shown below The headset ON OFF light is on when the headset is charging ON OFF light Insert VOLUME 1 Insert the headset into 2 Push the headset downward the charging cradle until the ON OFF light on the headset turns on CAUTION There may be a risk of detonation if you use a wrong type of battery Use only the supplied rechargeable battery or replacement battery model BT191545 BYD SL531732 To order visit our website at www telephones att com or call 1 800 222 3111 In Canada dial 1 866 288 4268 11 Headset base and lifter installation Installation preparation Before installing the headset base remove the rear bottom piece of the headset base by pushing it away from the base as shown in Figure 1 Install the headset base as shown on the following pages After completing installation option 1 2 or 3 see page 15 slide the rear bottom piece towards the headset base until it clicks into pla
17. vice Telephone line cord ba S 16 Headset base and handset lifter installation Adjust the corded handset audio 1 Make sure that LIFTER MODE light on the headset base is on Press the MODE button on the headset base to change the mode 2 Lift the corded handset to release the switch hook Place the corded handset aside 3 Place the headset earpiece in your ear A Press ON OFF on the headset to listen for a dial tone If there is no dial tone or the dial tone is unclear slide the LIFTER AUDIO ADJUST switch on the side of the headset base from A to G until the dial tone is clear LIFTER AUDIO ADJUST 17 Headset base and handset lifter installation Attach the Lifter 1 To choose where to install the lifter on your telephone look at the space underneath the corded handset If there is a speaker the lifter should be centered over the speaker If there is no speaker the lifter should be centered within the space Make sure the lifter arm is raised above the switch hook of the telephone base 2 Peel off the protective strips from the adhesive tape at the bottom of the lifter 3 Carefully place the lifter in the desired position and press down Headset base and handset lifter installation Adjust the switch hook presser position Turn the knob to move the switch hook presser until it is lined up with your teleph
Download Pdf Manuals
Related Search