Wilson Electronics Portable Carrying Case
Contents
1. Warning Use only Wilson Electronics power supply units Use of a non Wilson Electronics product may damage your equipment The Signal Booster may remain on all the time However leaving the Signal Booster on in a vehicle when it is not running can discharge the battery in a day or two Power supply may change due to upgrades A good option is to power the Signal Booster through the ignition switch so the Signal Booster is turned on and off with the vehicle IMPORTANT Do not power up the Signal Booster unless both antenna cables are attached to the Signal Booster AC DC power supply sold separately 859903 Note The aluminum casing of the Signal Booster will adjust very quickly to the ambient temperature of its environment For example in the summer when the inside of a car can reach 140 Fahrenheit the Signal Booster temperature may be 150 or higher The casing will be hot to the touch similar to a metal door handle or steering wheel Such high temperatures will not damage the Signal Booster nor do they pose a fire risk As recommended in these instructions when installing the Signal Booster in a vehicle select a location with adequate ventilation such as under the seat or dashboard Keep the area free of items that could block air flow to the Signal Booster ntact Wilson Electronics Technical Support Team with any questions at 866 294 1660 Or email tech wilsonelectronics com Hours 7am to 69m MST2. 811714 811910 811914 Inside this Package Items below may be included with some kits Products may change due to upgrades i Ultra Slim Adhesive Screw Swivel Bracket DUAL BAND Antenna Signal Booster Cellular Cradle Plus 4 IP Adhesive leA Bracket lente 12 Magnet 4 Mini Magnet Mount Antenna Mount Antenna AC DC power supply 859903 12 inch Magnet Mount Soft Carrying 12 V DC power supply vehicle Products may change due to upgrades Optional Items and Accessories Cellular Cradle Plus 301246 Mini Magnet Mount Antenna Antenna Case Window Bracket Ultra Slim Antenna 301113 301103 859924 901128 301143 Available at www WilsonElectronics com Appearance of device and accessories may vary How it Works The Signal Booster in conjunction with the use of an Outside Antenna will collect the signal from the cell tower and send it through the cable to the Signal Booster The state of the art technology that powers this Signal Booster is designed to increase your signal more than 20 times and reduce disconnects and dropped calls The boosted signal is then sent to the Cellular Cradle Plus or Ultra Slim Antenna depending on which one you have Your cellular device receives the improved signal When the cellular device transmits the signal goes through the Cellular Cradle Plus or Ultra Slim Antenna boosted by the Signal Booster and broadcasted back to the cell tower through the Outside Ant
3. To receive the best cell signal select a window location at least 12 inches away from any radio or television antennas and free of obstructions Installing the Outside Antenna Using the suction cups position the mounting bracket on the window at a height convenient to where the Signal Booster will be located then attach the antenna to the bracket The antenna must be installed vertically Signal performance will be degraded if the antenna is not vertical Warning The antenna used with this Signal Booster must have a separation distance of at least 12 inches from all persons Installing the Wilson Electronics Signal Booster Select a location to install the Signal Booster that is away from excessive heat direct sunlight or moisture and that has proper ventilation Recommended installation locations are e On a desk or table top e In a bookshelf e On the floor Warning Do not plug in the AC power supply until both antenna cables are attached to the Signal Booster Wilson Electronics recommends that all AC power 4 Too 6 aa supplies for home electronics be plugged into a Surge Protector Power Strip J Run the cable from the Outside Antenna and attach it to the connector labeled Outside Antenna on the Signal Booster Attach the Cellular Cradle Plus or Ultra Slim cable to the connector labeled Inside Antenna on the Signal Booster Then attach the
4. M2M With extensive experience in antenna and Signal Booster research and design the company s engineering team uses a state of the art testing laboratory including an anechoic chamber and network analyzers to fine tune antenna designs and performance For its Signal Boosters Wilson Electronics uses a double electrically insulated RF enclosure and cell tower simulators for compliance testing All products are engineered and assembled in the company s 55 000 square foot headquarters in St George Utah Wilson Electronics has product dealers in all 50 states as well as in countries around the world ntact Wilson Electronics Technical Support Team with any questions at 866 294 1660 Or email tech wilsonelectronics com Hours 7am to 6pm MST 30 Day Money Back Guarantee All Wilson Electronics products are protected by Wilson Electronics 30 day money back guarantee If for any reason the performance of any product is not acceptable simply return the product directly to the reseller with a dated proof of purchase 1 Year Warranty Wilson Electronics Signal Boosters are warranted for one 1 year against defects in workmanship and or materials Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase Signal Boosters may also be returned directly to the manufacturer at the consumer s expense with a dated proof of purchase and a Returned Material Authorization RMA nu
5. 0 In Vehicle Installation Diagram In Building Installation Diagram Contact Wilson Electronics Technical Support Team with any questions at 866 294 1 Or email tech wilsonelectronics com Hours 7am to 6pm MST Installing the Outside Antenna To receive the best cell signal select a location in the center of the vehicle s roof that is 12 inches away from any other antennas and free of obstructions The antenna must be installed vertically Signal performance will be degraded if the antenna is not vertical Warning The antenna used with this Signal Booster must have a separation distance of at least 12 inches from all persons The antenna cable may run through the door to the Signal Booster For a more professional looking installation run the antenna cable under the door seal Carefully pull down the door seal Run the cable through the seal and push the seal back into place This prevents constant wear and tear on the cable as the door opens and closes Carefully Run Cable Pull Down Under Door Seal Seal n The antenna cable is small enough to easily S tuck under the door seal or plastic molding lt gt Tuck Cable Under Seal ntac Wilson Electronics Technical Support Team with any questions at 866 294 1660 Or email tech wilsonelectronics com Hours 7am to 6pm MST Installing the Wilson Electronics Signal Booster Select a location to install the Signal Booster that is away f
6. 1 0 dBm 1 7 dBm 3 2 5 dBm 1 8 dBm 4 5 0 dBm 4 3 dBm 5 7 0 dBm 6 3 dBm 6 8 5 dBm 7 8 dBm Noise Figure typical 3 5 dB nominal Isolation uplink downlink more than 50 dB Power Requirements Notes 12 V 2 A subject to uplink power Nominal gain is the maximum gain at any frequency in the passband 2 Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the passband amplification One of the frequencies is lower than the passband and the other is higher 3 The Manufacturer s rated output power of this equipment is for single carrier operation For situations when multiple carrier signals are present the rating would have to be reduced by 3 5 dB especially where the output signal is re radiated and can cause interference to adjacent band users This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device D The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled Signal Booster Specifications Not for use in U S or Canada Model Number 811510 14 811710 14 811910 14 Frequency Gain up down 880 960 MHz 880 960 MHz 1710 1880 MHz 880 960 MHz 1920 2170 MHz 25 dB 25 dB Max RF 34 dBm 32 dBm Noise Figure 3 5 dB nominal Flatness up down 2dB 2dB Isolation gt 50 d
7. 29 656 7 409 186 7 783 318 7 684 838 12 714 994 Wilson Electronics Inc 3301 East Deseret Drive St George UT 84790 For additional Technical Support visit www WilsonElectronics com or email at tech wilsonelectronics com Phone 866 294 1660 Local 435 673 5021 Fax 435 656 2432 www twitter com WilsonCellular www facebook com WilsonCellul Contact Wilson Electronics Technical Support Team with any questions at 866 294 1 Or email tech wilsonelectronics com Hours 7am to 6pm MST Signal Booster Specifications Model Number Connectors Impedance input output Dimensions Weight Dual Band Specifications 811210 FME Male 50 Ohms 5X3 DX F2Inenoni2 n8 9X SCM 1 03 Ibs or 0 468 kg Frequency 824 894 MHz 1850 1990 MHz Passband Gain nominal 800 MHz uplink downlink 1900 MHz uplink downlink 25 06 25 0B 220 dB Bandwidth nominal 800 MHz uplink downlink 1900 MHz uplink downlink 112 MHz 110 MHz 25 dB 25 dB 53 MHz 62 MHz Power output for single cell phone uplink 800 MHz 1900 MHz CDMA 33 0 dBm 29 3 dBm GSM 34 3 dBm 30 3 dBm EDGE 34 1 dBm 30 2 dBm AMPS 30 1 dBm Power output for single received channel 800 MHz 1900 MHz downlink CDMA 5 1 dBm 6 8 dBm GSM 3 2 dBm 4 4 dBm EDGE 3 2 dBm 4 6 dBm AMPS 3 2 dBm Power output for multiple received channels downlink Maximum Power The maximum power is reduced by Number of the number of channels channels 800 MHz 1900 MHz 2
8. B Power Requirements 12 V 2 A subject to uplink power Connectors FME Male 50 ohms Dimensions 5 x 3 5 x 1 2 inch 12 7 x 8 9 x 3 cm Weight 1 03 Ibs 0 468 kg w Wilson Electronics Inc AIG 110464_REV 21_ 11 30 11
9. Cellular Cradle Plus or Ultra Slim to your cell phone or data c See page 5 amp 6 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1 Or email tech wilsonelectronics com Hours 7am to 69m MST Warnings and Recommendations As Warning The antenna must be installed with a separation distance of at least 12 inches from any vehicle occupant and must not be located or operating in conjunction with any other antenna or Signal Booster Use of this Signal Booster with an antenna providing gain higher than 6 12 dBi is in violation of FCC regulations for which the offender is fully liable All Wilson Electronics mobile antennas provide 6 12 dBi gain or less A Warning Do not connect the power supply to the Signal Booster until the Outside Antenna and Cellular Cradle Plus or Ultra Slim Antenna cables are attached to the Signal Booster As Warning Do not plug the Signal Booster directly into the cell phone or cellular data card using an antenna adapter It could damage the Signal Booster cell phone and or cellular data card About Wilson Electronics Wilson Electronics Inc has been a leader in the wireless communications industry for over 40 years The company designs and manufactures Signal Boosters antennas and related components that significantly improve cellular signal reception and transmission in a wide variety of applications both mobile marine RV vehicles and in building home office
10. e suggest that you choose a flat smooth surface like the console area of your vehicle between the two front seats If this is not available in your vehicle you may mount the cradle on the front of the dashboard If mounting the cradle on a sloped area of the dashboard in your vehicle please note that gravity may affect the adhesive over time Use the screw mount for a more permanent attachment Attaching the Cradle Option 1 Adhesive Bracket Clean the area where the bracket will be mounted with the alcohol wipe included in some kits and a soft cloth Allow to dry Peel the backing to expose the adhesive and press the bracket onto the desired location in the vehicle Note Be sure the bracket is positioned vertically Allow the adhesive to cure for 24 hours before you attach the cradle Note Once the cradle is attached you can adjust the angle of the adhesive bracket by applying gentle pressure to the top or bottom of the cradle Option 2 Adhesive Screw Swivel Bracket Clean the area where the bracket is to be mounted with the alcohol wipe included in some kits and a soft cloth Allow to dry For an adhesive mount peel the backing to expose the adhesive and press the bracket onto the desired location in the vehicle Allow the adhesive to cure for 24 hours before you attach the cradle For a screw mount use an ice pick or awl to punch through the adhesive and expose the four screw holes in the bracket N
11. enna lf your kit contains the Cellular Cradle Plus it provides a convenient place to stow your cell hone and allows the driver to keep both hands on the wheel while using the phone greatly easing safety This kit may include different mounting options for installing the cradle on sh or console of your vehicle ur kit does not contain a Cellular Cradle Plus it is available for purchase at www WilsonElectronics com ntact Wilson Electronics Technical Support Team with any questions at 866 294 1660 Or email tech wilsonelectronics com Hours 7am to 6pm MST Before Getting Started This guide will help you properly install your Wilson Electronics SIGNALBOOST Dual Band Signal Booster It is important to read through all of the installation steps for your particular application prior to installing any equipment Read through the instructions visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment Please contact Wilson Electronics Technical Support with any questions at 866 294 1660 You may also send an email to tech wilsonelectronics com Installation Overview The following steps provide a summary of the Signal Booster antenna installation process using the Mini Magnet Mount or Magnet Mount Antenna However they are not a substitute for the complete installation instructions on the following pages which you should read thoroughly If you are using a different Outs
12. ide Antenna follow the specific instructions that come with it STEP 1 Install the Outside Antenna For a In Vehicle installation attach the Outside Antenna in the center of the vehicle s roof and run the cable through the door to the Signal Booster For In Building installation affix the optional window bracket to a window with the suction cups attach the Outside Antenna to the bracket and run the cable to the Signal Booster See page 3 for In Vehicle and page 8 for In Building STEP 2 Install the Signal Booster Position the Signal Booster in a well ventilated location away from direct sunlight Run the cable from the Outside Antenna and attach it to the connector labeled Outside Antenna on the Signal Booster See page 4 STEP 3 Attach the Cellular Cradle Plus or Ultra Slim Antenna Attach the Cellular Cradle Plus or Ultra Slim cable to the connector labeled Inside Antenna on the Signal Booster If using the Ultra Slim Antenna attach the antenna to your cell phone or cellular data card with the VELCRO provided See page 6 STEP 4 Power up the Signal Booster IMPORTANT Before connecting the power supply ensure that both the Outside Antenna cable and the Cradle Plus or Ultra Slim cable are connected See page 7 Connection onnection AC Power Supply and Window Bracket sold separately Part 85994
13. mber supplied by Wilson Electronics Wilson Electronics shall at its option either repair or replace the product Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer if located in the USA This warranty does not apply to any Signal Boosters determined by Wilson Electronics to have been subjected to misuse abuse neglect or mishandling that alters or damages physical or electronic properties RMA numbers may be obtained by phoning Technical Support at 866 294 1660 This device complies with Part 15 of FCC rules The transaction is subject to two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by Wilson Electronics could void the authority to operate this equipment Disclaimer The information provided by Wilson Electronics Inc is believed to be complete and accurate However no responsibility is assumed by Wilson Electronics Inc for any business or personal losses arising from its use or for any infringements of patents or other rights of third parties that may result from its use Copyright 2011 Wilson Electronics Inc All rights reserved One or more of the following U S Patent numbers may apply to the Signal Booster in this product D596 614 D596 615 D563 381 7 729 669 7 486 929 7 7
14. onelectronics com Hours 7am to 69m MST The Ultra Slim must be placed directly on the cell phone or cellular data card to work properly Attach the Ultra Slim to the cell phone or cellular data card with the VELCRO provided The Ultra Slim cable is long enough to reach the Signal Booster location This allows for ease and convenience of use To adjust the Ultra Slim for the best signal go to a weak signal location where your cell phone registers only 1 2 bars without the Ultra Slim connected Be sure the Signal Booster is turned off when checking for low signal Then attach the Ultra Slim to the phone power up the Signal Booster and you should see a signal improvement of 2 or more bars Note Many phones take up to 30 seconds to reset the bar indicator To maximize performance attach the Ultra Slim as close as possible to the original antenna on your cell phone or cellular data card Figure 1 Figure 2 To Signal Boa In Vehicle amp In Building Powering Up the Signal Booster Make sure both the Outside Antenna and Cellular Cradle Plus or Ultra Slim Antenna cables are connected before powering up the Signal Booster SIGNALBOOS DustBand cettuiariPcs ff Carefully insert the power cable 1 at i Connect the power cable from the power supply to the Signal Booster input marked 12 V DC and insert the large end into the power socket or the vehicle power outlet
15. ote Screws are not included in this kit Using the bracket as a template mark the locations for the screws as shown drill pilot holes and attach the bracket with screws not included Once the cradle is attached you can loosen the knurled wheel and swivel the hook to the desired angle then re tighten the wheel Once you have installed the mount in the desired location attach the cradle by aligning the rectangular hole on its back with the hook on the mount Grasping the sides of the Cradle slide it downward approximately 1 4 inch into place ntact Wilson Electronics Technical Support Team with any questions at 866 294 1660 Or email tech wilsonelectronics com Hours 7am to 6pm MST Installing the Ultra Slim Antenna Included in some kits Cellular data card For cell phones with an internal antenna place the Ultra Slim on the back of the phone near the top Figure 1 Note Certain phones such as the Motorola RAZR have internal antennas at the base rather than the top in which case the Ultra Slim should be attached at the bottom rear of the phone For cell phones with an external antenna place the Ultra Slim directly below the phone s original antenna Figure 2 If you have any questions as to the location of the antenna on your phone call Wilson Electronics Technical Support at 866 294 1660 Contact Wilson Electronics Technical Support Team with any questions at 866 294 16 Or email tech wils
16. rom excessive heat direct sunlight or moisture and that has proper ventilation Recommended installation locations for the Signal Booster are e Under the seat e Under the dash Run the cable from the Outside Antenna and attach it to the connector labeled Outside Antenna on the Signal Booster Warning Do not plug in the DC power supply until the Outside Antenna and Cellular Cradle Plus or Ultra Slim Antenna cables are attached to the Signal Booster Attach the cable from the Cellular Cradle Plus or the Ultra Slim Antenna to the connector on the Signal Booster Warning Do not plug the Signal Booster directly into the cell phone or cellular data card using an antenna adapter It could damage the Signal Booster cell phone and or cellular data card Adjusting the Cradle Plus Arms Included with your Cradle Plus are various sized arms which will provide you with multiple options to customize the Cradle to fit your phone 1 Change arms 2 Reposition arms Gently grab the arm and lift upward until Position the arm above a different slot the arm slides free from the Cradle the Cradle Gently slide the arm dow the arm is firmly in place Contact Wilson Electronics Technical Support Team with any questions at 866 294 16 Or email tech wilsonelectronics com Hours 7am to 69m MST Installing the Cellular Cradle Plus Included in some kits For best mounting results and long term performance w
17. signal lation nstallation Waal SIGNALBOOST Dual Band Mobile as Signal Booster I 811510 is single band Contents ROW IC WOKS 23608 i e Gee geek eau ee heen ee ceed ae 1 Before Getting Started 0 0 0 ce eee eee 2 Installation Overview 2 0 0 0 0c ee eee 2 In Vehicle Installation n nananana aaa 3 Outside Antenna anaana aaaea aaa 3 Signal Booster naana anaa a Yoewae fe 4 Cellular Cradle PluS nananana 5 Ultra Slim Antenna anaana aaaea aaa 6 Powering Up the Signal Booster 00 7 In Building Installation i420 aw cee ew ee ee we 8 Warnings and Recommendations 05 9 Guarantee and Warranty 0 20000 cece eee 10 Signal Booster Specifications Back Cover Appearance of device and accessories may vary Note This manual contains important safety and operating information Please read and follow the instructions in this manual Failure to do so could be hazardous and result in damage to your Signal Booster amp Wilson Electronics Inc Installation Instructions for the Following Wilson Electronics Signal Booster SIGNALBOOST Dual Band Mobile Signal Booster Model 811210 FCC ID PWO819DA IC 4726A 819DA The term IC before the radio certification number only signifies that Industry Canada technical specifications were met Not For Sale in U S Canada 811510 811514 811710
Download Pdf Manuals
Related Search