Wilson Electronics Three way Splitter
Contents
1. 3 The In Line should be placed where it can make up for installation gain loss due to cable taps or splitters Optimal location is near or directly connected to the Inside Antenna 4 a Connect a cable to the In Building Signal Booster at the connector labeled Inside Antenna b Run the cable to the In Line attach to the connector labeled Outside Antenna c From the In Line connector marked Inside Antenna run a cable to the Inside Antenna For more information on running cable refer to diagrams on pages 3 amp 4 5 Before powering up the In Line verify that all cables are connected and check that all connections are tight Note Be careful when plugging the connectors in so as not to bend the center pins on the connectors 6 The In Line has been packaged with the gain control knobs adjusted to the highest gain position If one or both of the lights are not green refer to pages 9 amp 10 A Warning Connecting the Signal Booster directly to a cell phone with use of an adapter may damage the cell phone and or the Signal Booster Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Before Getting Started This guide will help you properly install your Wilson Electronics Signal Booster It is important to read through all of the installation steps for your particular application prior to installin2. All Wilson Electronics products are protected by Wilson Electronics 30 day money back guarantee If for any reason the performance of any product is not acceptable simply return the product directly to the reseller with a dated proof of purchase 2 Year Warranty Wilson Electronics Signal Boosters are warranted for two 2 years against defects in workmanship and or materials Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase Signal Boosters may also be returned directly to the manufacturer at the consumer s expense with a dated proof of purchase and a Returned Material Authorization RMA number supplied by Wilson Electronics Wilson Electronics shall at its option either repair or replace the product Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer if located within the continental U S This warranty does not apply to any Signal Booster determined by Wilson Electronics to have been subjected to misuse abuse neglect or mishandling that alters or damages physical or electronic properties Failure to use a surge protected AC Power Strip with at least a 1000 Joule rating will void your warranty RMA numbers may be obtained by contacting Technical Support at 866 294 1660 Disclaimer The information provided by Wilson Electronics LLC is believed to be complete and accurate However no responsibility is assumed by
3. channel downlink 30 2 dBm 30 5 dBm 3Power output for multiple transmitted channels uplink Maximum Power The maximum power is reduced by the number of channels Number of channels 800 MHz 1900 MHz 2 10 6 dBm 9 4 dBm 3 14 1 dBm 12 9 dBm 4 16 6 dBm 15 4 dBm 5 18 5 dBm 17 4 dBm 6 20 1 dBm 19 0 dBm 4Power output for multiple received channels downlink Maximum Power The maximum power is reduced by the number of channels Number of channels 800 MHz 1900 MHz 2 22 3 dBm 21 dBm 3 18 8 dBm 17 4 dBm 4 16 3dBm 14 9 dBm 5 14 4 dBm 13 0 dBm 6 12 8 dBm 11 4 dBm eree a aon re Isolation gt 45 dB Power Requirements 110 240 V AC 50 60 Hz 8 W Notes 1 Nominal gain is the maximum gain at any frequency in the passband 2 Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB lower than the passband amplification One of the frequencies is lower than the passband and the other is higher 3 The Manufacturer s rated output power of this equipment is for single carrier operation For situations when multiple carrier signals are present the rating would have to be reduced by 3 5 dB especially where the output signal is re radiated and can cause interference to adjacent band users This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device 4 The maximum power for 2 or more simultaneous si
4. 0 years The company designs and manufactures Signal Boosters antennas and related components that significantly improve cellular phone signal reception and transmission in a wide variety of applications mobile vehicle RV marine and in building home office machine to machine With extensive experience in antenna and Signal Booster research and design the company s engineering team uses a state of the art testing laboratory including an anechoic chamber and network analyzers to fine tune antenna designs and performance For its Signal Boosters Wilson Electronics uses a double electrically shielded RF enclosure and cell tower simulators for compliance testing Wilson Electronics Signal Boosters feature patented Smart Technology I that enables them to automatically adjust their power based on cell tower requirements By detecting and preventing oscillation feedback signal overload and interference with other users these Smart Technology I Signal Boosters improve network cell phone areas without compromising carrier systems All products are engineered and assembled in the company s 100 000 square foot headquarters in St George Utah Wilson Electronics has product dealers in all 50 states as well as in countries around the world Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST 30 Day Money Back Guarantee
5. EOI tion iais In Line or 75 Ohm In Line 17dB Adjustable Gain 800 1900 MHz Smart Technology II Signal Booster Contents Quick Install Overview 2 2 0 0 0 00 eee 2 Installation Diagram 4 0002 ea dee ek od ee hee ee deen ea bs 3 Understanding the Signal Booster Lights 9 Warnings and Recommendations 11 Appearance of device and accessories may vary Note This manual contains important safety and operating information Please read and follow the instructions in this manual Failure to do so could be hazardous and result in damage to your Signal Booster amp Wilson Electronics LLC Installation Instructions for In Line or 75 Ohm In Line 17dB Adjustable Gain 800 1900 MHz Smart Technology II Signal Booster Model 276215 FCC ID PWO276215 IC 4726A 276215 The term IC before the radio certification number only signifies that Industry Canada technical specifications were met How it Works The In Line Signal Booster is designed to provide an additional 17dB gain to compensate for signal loss due to a long cable run or the use of taps or splitters The In Line Signal Booster allows installation of multiple inside antennas with minimal signal loss and is installed between a Wilson indoor Signal Booster like the AG Pro Installer and the Inside Antenna Optimally the In Line Signal Booster is installed after long runs of cable and or taps and splitters t
6. Place as close as possible Vara ISS A Le to splitter E Surge Protector Surge Protector Power Strip Power Strip Inside Antennas Surge Protector Power Strip Surge Protector Power Strip In Line Place as close as possible to Inside Antennas Inside Antennas Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Reasons for Using an In Line with In Building Installations Covering multiple rooms or even floors of a building can be challenging as each is a different size and shape Balancing the signal coverage can require multiple attenuators cables taps and splitters All of these can decrease your system gain and coverage Reasons to install an In Line include 1 Cable loss Long runs of cable from the Inside Antenna to the main In Building Signal Booster may have significant loss or require Wilson 400 low loss cable 2 Splitter loss When multiple rooms must be evenly covered a splitter evenly divides the signal for separate Inside Antennas Each division reduces system gain and inside coverage area 3 Tap loss Taps pass the signal with low attenuation out one port and pass the signal with high attenuation port continues on to another location possibly with more spl
7. Wilson Electronics LLC for any business or personal losses arising from its use or for any infringements of patents or other rights of third parties that may result from its use _ Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Next Usable Cellular Signal Without a Wilson Booster 50 Miles Copyright 2013 Wilson Electronics LLC All rights reserved U S Patent Nos 7 221 967 7 729 669 7 486 929 7 409 186 7 783 318 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST In Line Specifications Part 806215 806715 Model Number 276215 Antenna connectors N Female F Female Antenna impedance 50 ohm 75 ohm Dimensions 5 7 x 4 2 x 1 5 inch 14 0 x 10 8 x 3 9 cm Weight 1 27 Ibs 0 544 kg Frequency 824 894 MHz 1850 1990 MHz Passband Gain nominal 800 MHz uplink downlink 17 dB typical 19 dB max 17 dB typical 19 dB max 1900 MHz uplink downlink 17 dB typical 19 dB max 17 dB typical 19 dB max 220 dB Bandwidth nominal Uplink Downlink 800 MHz 26 MHz typical 29 MHz maximum 29 MHz typical 32 MHz max 1900 MHz 63 MHz typical 69 MHz maximum 63 MHz typical 70 MHz max Power Output 800 MHz 1900 MHz Power output for single cell phone uplink 3 7 dBm 2 dBm Power output for single received
8. e In Line and attach it to the connector labeled Inside Antenna on the In Line For more information refer to pages 3 amp 4 Plug the power supply into the In Line input marked POWER carefully to avoid damaging the center pin and then into a surge protected AC Power Strip with at least a 1000 Joule rating If the In Line does not have two green lights please refer to pages 9 amp 10 If you Know that only one frequency band 800 or 1900 is available in your coverage area or going to be used reduce the gain control on the frequency band that is NOT in use to the lowest setting This will reduce the power consumption of the In Line Using multiple In Building Signal Boosters other than the In Line in one installation could cause interference to the cell tower Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Technical Support hours are Mon Fri 7am to 6 pm MST Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Figure 4 CORRECT INSTALLATION Point antennas away from each other Recommended placement for In Line Signal Booster Figure 5 INCORRECT INSTALLATION Never point antennas toward each other Inside Panel Antenna 4 Signal Booster ianen Contact Wilson Electronics Techn
9. e In Line to reset Continue this adjustment until the indicator light turns green When you are turning down the gain you are reducing the inside coverage area If the amount of coverage area is sufficient for your needs and the light is green the installation is complete If the coverage area is not large enough it is necessary to increase the separation distance of the antennas by moving them horizontally or vertically farther apart or both see Figure 7 below Then increase the gain until the red light comes on and then slightly keep decreasing the gain until the green light appears If after separating the antennas your coverage area is still too small contact Wilson Electronics Technical Support Team for assistance 866 294 1660 Figure 7 Signal Booster il Outside Antenna f M Inside A n To increase coverage move Outside amp Inside Antennas farther apart horizontally or vertically The In Line can be reset by disconnecting and reconnecting the power supply from the Signal Booster Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Warnings and Recommendations A Warning A Warning A Warning A Warning As Warning The Directional Antenna must always be located so the back or side points to the Inside Antenna Never point th
10. e front of the Outside Antenna toward the Inside Antenna this is to prevent oscillation Connecting the In Building Signal Booster directly to the cell phone with use of an adapter will damage the cell phone Use only the power supply provided Use of a non Wilson Electronics product may damage your equipment RF Safety FCC regulations require that the Inside Antenna used with this Signal Booster be listed on page 1 of this installation guide Use of other antennas is not permitted The antenna must be located 8 inches or more from all persons Verify that both the Outside Antenna and the Inside Antenna are connected to the In Building Signal Booster amp In Line before powering them up Recommendation Lightning Surge Protection is recommended for all in building installations This device complies with Part 15 of FCC rules Operation is subject to two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Changes or modifications not expressly approved by Wilson Electronics could void the authority to operate this equipment Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email techQwilsonelectronics com Mon Fri Hours 7 am to 6 pm MST About Wilson Electronics Wilson Electronics LLC has been a leader in the wireless communications industry for over 4
11. g any equipment Read through the instructions visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment Contact Wilson Electronics Technical Support with any questions at 866 294 1660 Installation Diagrams Note Do not install the In Line without Figure 1 an In Building Signal Booster between One In Line amp One Inside Antenna the Outside Antenna and In Line Note Install the In Line as close as Outside Antenna possible to Inside Antenna for optimal performance Lightning Surge Protector Splitter Options Signal Booster Surge Protector Power Strip 2 B 859957 50 ohm 4 Way 859981 3 wo ee 50 ohm 2 Way 859993 E 75 oh 5 ohm Ea 3 Way 859994 75 ohm fe In Line Place near Indoor Antenna as close as possible for optimal performance Surge Protector Power Strip ntenna Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Figure 3 Two In Lines amp Two Inside Antennas Figure 2 One In Line amp Two Inside Antennas Outside Antenna Outside Antenna Lightning Surge Protector Lightning Surge Protector a Signal Booster LP LM NN B yA Surge Protector Power Strip 2 In Line im Signal Booster i
12. gnals will be reduced by 6 dB every time the number of signals is doubled amp Wilson Electronics LLC 3301 East Deseret Drive St George UT 84790 For additional Technical Support visit www WilsonElectronics com or email at tech wilsonelectronics com Phone 866 294 1660 Local 435 673 5021 Fax 435 656 2432 www twitter com WilsonCellular www facebook com WilsonCellular AIG 111003_In Line_Rev10_04 16 13
13. ical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Understanding the In Line Lights and Troubleshooting The In Line is equipped with two indicator lights one for the 800 MHz band and the other for the 1900 MHz band During this time both lights will do one of the following 2 things Figure 6 f 800m 1900m Indicator light Indicator light w Wilson Electronics LLC SMART TECHNOLOGY I Adjustable Gain Signal Booster 1 3 3 Gain control Al 10 10 Gain control s 14 Wy 14 Note The In Line can be reset by disconnecting and reconnecting the power supply from the Signal Booster 1 GREEN If the indicator lights are green the In Line is operating properly If you are happy with the coverage area in your building then you are done Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST 2 RED If either of the two indicator lights on the In Line are red this indicates that the In Line has shut down on that frequency to prevent an oscillation feedback First make sure that all the connections are tight Then reduce the gain for that frequency in small increments by rotating the gain control counter clockwise waiting 5 seconds between each adjustment for the In Line to reset it may take up to 3 minutes for th
14. ilding Signal Booster and Inside Antenna Note It is important to have adequate air ventilation Maintain at least 6 inches of clearance from surrounding objects The In Line should be placed where it can make up for installation gain loss due to cable taps or splitters Optimal location is near or directly connected to the Inside Antenna Note For distances of 20 feet or more use Wilson low loss cable to prevent significant signal loss or contact Wilson Electronics Technical Support Team for assistance 866 294 1660 Note Be careful when plugging the connector in so as not to damage the center pins on the connectors IMPORTANT NOTICE i is very important to power your Signal Booster using a surge protected AC Power Strip with at least a 1000 Joule rating 4 7955 E na e Failure to do this will void your warranty in the event of a power surge or lightning strike L Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Powering up a Wilson Electronics In Line 1 Never point the front of a Directional Outside Antenna toward the Inside Antenna Refer to Figures 4 amp 5 on page 8 Run the antenna cable from the In Building Signal Booster Inside Antenna connector to the In Line Outside Antenna connector and attach to both connectors Run the Inside Antenna cable to th
15. itters and taps downstream The attenuation port typically runs directly to an Inside Antenna 4 Increased system dynamic range A user who gets too near an Inside Antenna can lower the gain and coverage area for all other users The In Line adds dynamic range to the In Building installation and reduces use of the main Signal Booster automatic gain control The In Line overcomes the losses associated with large In Building installations The In Line recovers inside coverage area that is normally lost due to cable splitter and tap loss By installing the In Line near an Inside Antenna uplink noise figure is minimized and downlink power is maximized Additionally the In Line enhances performance of the main Signal Booster by increasing the systems gain and input signal dynamic range The variable gain knobs on the In Line allow for simple quick signal level balancing and installation Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Installing the Wilson Electronics In Line Select a location to install the In Line that is away from excessive heat direct sunlight moisture and has proper ventilation Do not place in an air tight enclosure Recommended installation locations for the In Line are e On a shelf e In a closet e Near a power outlet e Near the Inside Antenna Where there is more than 5dB loss between In Bu
16. o compensate for the signal loss The In Line Signal Booster can be installed in the middle of a cable run or near the inside antenna The In Line is designed to offset cable and splitter tap loss for In Building installations It should be used on the Inside Antenna side of a Wilson Electronics In Building Signal Booster such as the AG Pro 75 Inside this Package Note Kits may contain different accessories In Line AC DC Power Supply 806215 amp 806715 6V 2 5A 859912 Indoor Antenna Options Tap Option 50 ohms 75 ohms 301135 301155 g a l 304451 304471 EA Note Splitter Options 304452 304472 on page 3 304453 304473 50 ohm 859907 Appearance of device and accessories may vary To purchase call Wilson Electronics Sales Department at 800 204 4104 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 or email tech wilsonelectronics com Mon Fri Hours 7 am to 6 pm MST Quick Install Overview Refer to Installation Diagrams on page 3 amp 4 Contact Wilson Electronics Technical Support Team with any questions at 866 294 1660 _ Install In Building Signal Booster such as the AG Pro 75 sold separately Use the installation guide for the model you purchased to install 2 Select a location to install the In Line that is away from excessive heat direct sunlight moisture and has proper ventilation Do not place the In Line in an air tight enclosure
Download Pdf Manuals
Related Search